H3C基本配置(默认路由)
H3C基本配置
#进入系统视图
#配置设备名
[H3C]sys name RouterA
#设置super（明文）密码
[RouterA]super password simple quidway
#设置super（密文）密码
[RouterA]super password cipher quidway
#启用tel net管理功能
[RouterA]user-i nteface vty 0 4
[RouterA-ui-vtyO-4]authe nticati on-m ode password [RouterA-ui-vtyO-
4]set authe nticati on password quidway [RouterA-ui-vty0-4]user
privilege level 3 [RouterA-ui-vtyO-4]quit
[RouterA]tel net server en able
#配置端口IP地址
[RouterA]i nt e 0
[RouterA-EthernetO]ip add 192.168.1.1 24
#启动端口
[RouterA-Ether netO ]undo shutdow n
[RouterA-EthernetO]quit
#保存,在任何视图下
#查看当前设备配置信息
[RouterA]display curre nt-con figurati on
# 查看Flash 中的配置（相当于CISCO start-config） [RouterA]display
saved-c on figurati on
#删除FLASH中的配置信息（重置设备配置）
[RouterA]reset saved-c on figurati on
#重新启动设备
#显示系统软件版本
[RouterA]display version
#访问TFTP服务器
上传
#交换机IP地址
[H3C] in t vla n 1
[H3C-Vla n-in terface1]ip add 192.168.1.1 24
[H3C-Vla n-in terface1]u ndo ip add 192.168.1.1 24 #创建VLAN
[H3C]vla n 10
[H3C]u ndo vlan 10
#向VLAN添加一个、多个端口
[H3C-vla n10]port e 1/0/1
[H3C-vla n10]port e 1/0/5 to e 1/0/7
[H3C-vla n10]port e 1/0/8 to e 1/0/9 e 1/0/11 to e 1/0/12 #显示VLAN信息
[H3C]dis vla n
#设置以太网端口的链路类型为TRUNK
[H3C-Ethernet1/0/1]port lin k-type trunk
[H3C-Ethernet1/0/1]port trunk permit vlan all
[H3C-Ethernet1/0/1]port trunk pvid vlan 1
#设置以太网端口的链路类型为ACCESS
[H3C-Ethernet1/0/1]port lin k-type access
[H3C-Ethernet1/0/1]port access vlan 10
[H3C-Ethernet1/0/1]u ndo port access vlan
# 配置Loopback 环回接口
[H3C]i nt loopback 0
[H3C-Lookback0]ip add 10.1.1.1 24
#静态路由
[H3C]ip route 192.168.3.0 255.255.255.0 s 1/0
[H3C]u ndo ip route 192.168.3.0 255.255.255.0 s 1/0
#默认路由
[H3C]ip route 0.0.0.0 0.0.0.0 s 1/0
缺省路由和静态路由
实验拓扑
Eth 0/0 Eth 0/0 Eth 0/0
PCI PC2 PC3二、实验要求
使各网络间能互相通信，R1和R3使用缺省路由，指向R2 ;在R2上配置静态路由到
192.168.1.0 和192.168.3.0 的子网
三、实验步骤
R1:
[R1]ip route 0.0.0.0 0.0.0.0 192.168.10.2
R2:
[R2]ip route 192.168.1.0 255.255.255.0 192.168.10.1
[R2]ip route 192.168.3.0 255.255.255.0 192.168.20.2
R3:
[R3]ip route 0.0.0.0 0.0.0.0 192.168.20.1
RIPv1
一、实验拓扑
Eth 0/0 Eth 0/0 Eth 0/0
PCI PC2 PC3二、实验要求
使用RIPv1,使各子网间能正常通信
三、实验步骤
R1:
[R1]rip
[R1-rip-1] undo summary
[R1-rip-1] network 192.168.1.0
[R1-rip-1] network 192.168.10.0
R2:
[R2]rip
[R2-rip-1] undo summary
[R2_rip_1] network 192.168.2.0
[R2_rip_1] network 192.168.10.0
[R2_rip_1] network 192.168.20.0
R3:
[R3]rip
[R3-rip-1] undo summary
[R3-rip-1] network 192.168.3.0
[R3-rip-1] network 192.168.20.0
RIPv2
实验拓扑
Eth 0/0 Eth O/O Eth 0/0
PCI PC2 PC3二、实验要求
使用RIPv2,使各子网间能正常通信
三、实验步骤
R1:
[R1]rip
[R1-rip-1]versio n 2
[R1-rip-1] undo summary
[R1-rip-1] network 192.168.1.0
[R1-rip-1] network 192.168.10.0
R2:
[R2]rip
[R2-rip-1]v 2
[R2-rip-1] net 192.168.10.0
[R2-rip-1] net 192.168.2.0
[R2-rip-1] net 192.168.20.0
R3:
[R3]rip
[R3-rip-1]v 2
[R3-rip-1] undo summary
[R3-rip-1] network 192.168.3.0 [R3-rip-1] network 192.168.20.0