文档库 最新最全的文档下载
当前位置:文档库 › Sabic C2800 Datasheet

Sabic C2800 Datasheet

Sabic C2800 Datasheet
Sabic C2800 Datasheet

C YCOLOY? Resin C2800A sia Pacific: COMMERCIAL

Non-chlorinated and non-brominated flame retardant PC/ABS offering balanced flow and impact for various applications.

TYPICAL PROPERTIES1

TYPICAL VALUE Unit Standard

M ECHANICAL

T ensile Stress, yld, Type I, 2.0 in/min

8400

p si A STM D 638T ensile Strain, yld, Type I, 2.0 in/min 5%A STM D 638T ensile Strain, brk, Type I, 2.0 in/min 50

%A STM D 638T ensile Modulus, 2.0 in/min

389000p si A STM D 638F lexural Stress, yld, 0.10 in/min, 4 in span 13900p si A STM D 790F lexural Modulus, 0.10 in/min, 4 in span 389000p si A STM D 790H ardness, Rockwell R

120

-A STM D 785

I MPACT

Izod Impact, notched, 73°F

8

f t-lb/in A STM D 256 Instrumented Impact Total Energy, 73°F

515

i n-lb A STM D 3763

T HERMAL

V icat Softening Temp, Rate B/50

195

°F A STM D 1525H DT, 264 psi, 0.125 in, unannealed

165°F A STM D 648H DT, 264 psi, 0.250 in, unannealed 176°F A STM D 648 CTE, flow, -40°F to 140°F 4.E-051/°F A STM E 831 CTE, xflow, -40°F to 140°F 4.E-051/°F A STM E 831T hermal Conductivity

0.2W /m-°C A STM C 177R elative Temp Index, Elec

80°C U L 746B R elative Temp Index, Mech w/impact 70°C U L 746B R elative Temp Index, Mech w/o impact

80

°C U L 746B

P HYSICAL

S pecific Gravity

1.17

-A STM D 792S pecific Gravity, color

1.18-A STM D 792 Water Absorption, 24 hours @ 73°F

0.1

%

A STM D 570

Source GMD, last updated:

PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.

DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( S ELLER ) ARE SOLD SUBJECT TO SELLER S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESS OTHERWISE PROVIDED IN SELLER S

STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT. Each user is responsible for making its own determination as to the suitability of Seller s materials, products, services or recommendations for the user s particular use through appropriate end-use and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible use of any material, product, service or design do not, are not intended to, and should not be construed to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of any material, product, service or design in a manner that infringes any patent or other intellectual property right. SABIC and brands marked with ? are trademarks of SABIC or its subsidiaries or affiliates.(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are

measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.

(2) Only typical data for selection purposes. Not to be used for part or tool design.

(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.

(4) Internal measurements according to UL standards.

(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 sec Vertical Burn.

C YCOLOY? Resin C2800A sia Pacific: COMMERCIAL

TYPICAL PROPERTIES1

TYPICAL VALUE Unit Standard

P HYSICAL

W ater Absorption, equilibrium, 73F

0.4

%A STM D 570M old Shrinkage, flow, 0.125" (5)0.4 - 0.6%S ABIC Method M old Shrinkage, xflow, 0.125" (5)0.4 - 0.6%

S ABIC Method Melt Flow Rate, 260°C/2.16 kgf

16

g /10 min A STM D 1238

E LECTRICAL

V olume Resistivity

1.E+17

O hm-cm A STM D 257S urface Resistivity

>1.E+14O hm A STM D 257D ielectric Strength, in oil, 125 mils 457V /mil A STM D 149R elative Permittivity, 50/60 Hz 3-A STM D 150R elative Permittivity, 100 Hz 3

-A STM D 150D issipation Factor, 50/60 Hz 0.0048-A STM D 150A rc Resistance, Tungsten {PLC}6P LC Code A STM D 495H ot Wire Ignition {PLC)

3P LC Code U L 746A H igh Voltage Arc Track Rate {PLC}3P LC Code U L 746A H igh Ampere Arc Ign, surface {PLC}0P LC Code U L 746A C omparative Tracking Index (UL) {PLC}

1

P LC Code U L 746A

F LAME CHARACTERISTICS

U L Recognized, 94V-2 Flame Class Rating (3)

0.035

i n U L 94U L Recognized, 94V-0 Flame Class Rating (3)

0.058i n U L 94U L Recognized, 94-5VB Rating (3)0.091i n U L 94O xygen Index (LOI)

35

%

A STM D 2863

DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( Source GMD, last updated:

PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.

S ELLER ) ARE SOLD SUBJECT TO SELLER S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESS OTHERWISE PROVIDED IN SELLER S

STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT. Each user is responsible for making its own determination as to the suitability of Seller s materials, products, services or recommendations for the user s particular use through appropriate end-use and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible use of any material, product, service or design do not, are not intended to, and should not be construed to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of any material, product, service or design in a manner that infringes any patent or other intellectual property right.(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are

measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.

(2) Only typical data for selection purposes. Not to be used for part or tool design.

(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.

(4) Internal measurements according to UL standards.

(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 sec Vertical Burn.

C YCOLOY? Resin C2800A sia Pacific: COMMERCIAL

PROCESSING PARAMETERS

TYPICAL VALUE Unit

I njection Molding

D rying Temperature 170 - 180°F D rying Time

3 - 4h rs D rying Time (Cumulative)8h rs M aximum Moisture Content 0.04

%M elt Temperature 450 - 530°F N ozzle Temperature

450 - 530°F F ront - Zone 3 Temperature 440 - 530°F M iddle - Zone 2 Temperature 420 - 500°F R ear - Zone 1 Temperature 410 - 490°F M old Temperature 120 - 160°F B ack Pressure 50 - 100p si S crew Speed

40 - 70r pm S hot to Cylinder Size 30 - 80

%V ent Depth

0.0015 - 0.003

i n

? NOTE: Back Pressure, Screw Speed, Shot to Cylinder Size and Vent Depth are only mentioned as general guidelines. These may not apply or need adjustment in specific situations such as low shot sizes, thin wall molding and gas-assist molding.

Source GMD, last updated:

PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.

DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( S ELLER ) ARE SOLD SUBJECT TO SELLER S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESS OTHERWISE PROVIDED IN SELLER S

STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT. Each user is responsible for making its own determination as to the suitability of Seller s materials, products, services or recommendations for the user s particular use through appropriate end-use and other testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible use of any material, product, service or design do not, are not intended to, and should not be construed to grant any license under any patent or other intellectual property right of Seller or as a recommendation for the use of any material, product, service or design in a manner that infringes any patent or other intellectual property right.(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are

measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.

(2) Only typical data for selection purposes. Not to be used for part or tool design.

(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.

(4) Internal measurements according to UL standards.

(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 sec Vertical Burn.

相关文档