PSRL5017RX8-15N中文资料
AC/DC Switching Power Supply
FEATURES
● 2 Year Warranty
● Optional Top Cover Available ● Universal AC Input / Full Range ● Optional N+1 Active Current Sharing
● Peak Power 900W within 500uS duty duration ● Power Factor Corrected to EN61000-3-2 Class D ● High Power Density (Max. 9.1 Watts per cubic inch) ● Approved to UL/CUL/TUV/CB/CE & Class B Emissions ● U-Chassis & Enclosed with Built-in Fan Mechanical Options
SPECIFICATIONS:
PSRL5017R8-N Series
All specifications are based on 25o
C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
INPUT SPECIFICATIONS Input Voltage 90 - 264 VAC Full Range Input Current 12A at 90VAC and full load. Input Frequency 47 to 63Hz Inrush Current 70A max. @ 230VAC with full load cold start. Leakage Current 3.5mA max. @ 240VAC. Remote ON/OFF Designated as RSW on CN3, requires a low signal to inhibit output. OUTPUT SPECIFICATIONS Output Voltage See Table Output Power Range 800 Watts max with airflow. (See Note 3) Output Adjustability Output user adjustable ±5% minimum. Total Regulation ±1% Output Current See Table Ripple & Noise (peak to peak) ±1% Transient Response Returns to within 1% in less than 2.5ms for a 50% load change and the peak transient does not excess 5%. Hold-Up Time 20ms min. at 80% of full load. Overshoot Turn-On & Off overshoot < 5% over nominal voltage. Turn On Delay 1.5 seconds maximum at 230VAC.
Remote Sense
Designated as RS+ and RS- on CN3, total voltage compensation for cable losses with respect to the main
output. (Not available for current sharing models).
PROTECTION
Over Voltage Protection Unit latching down when output voltage exceeds 130% and recycle AC input to reset. Short Circuit Protection Trip without damage and auto-recovery. Over-Temperature Protection Unit protected of excessive operating ambient 85°C and automatic recovery. Over-Power Protection Fold back mode 110-140% and auto-recovery. Input Voltage Protection Power shut down under 80 ±5VAC, and recovered over 86VAC Input Fusing Protection A T12A/250V fuse is inserted in primary. GENERAL SPECIFICATIONS Efficiency 80% for 12V, and 83% minimum for other outputs @ 230VAC and full load.
Withstand Voltage
1500 VAC input line to chassis (10mA DC cut off current); 3000VAC between primary and secondary
windings. Primary to core 1500VAC. All for 3 seconds.
Burn In 45 ±5°C for one hour @ 230VAC with full load. PFC Active power factor correction meets EN61000-3-2 class D.
Power Good
Designated as PG on the CN3 and TTL high 100-500ms after regulation. It goes low at least 1ms before loss
of regulation for Power on Reset signal.
Grounding Test Apply 25A from ground pin of the three prong plug to the far most earth. Max allowable resistance is 0.1 ohm.
U Type
E Type
F Type
AC/DC Switching Power Supply SPECIFICATIONS (CONTINUED)
GENERAL SPECIFICATIONS (CONTINUED)
Current Sharing Designated as CSH on the CN3, optional single wired for forced current sharing function and parallel up to 4 units within 10% accuracy at full load.
Current Monitor Designated as CMN on the CN3 is a 0.5V to 3VDC output voltage to represent 0% to 100% output current.
LED Display Bi-color LED1 emit Green for Power On and emit Orange when protection is enabled or RSW is applied a low signal.
ENVIRONMENTAL SPECIFICATIONS
Operating Temperature 0°C to +70°C ambient, de-rating at 2.5% per degree from 50°C to 70°C. Storage Temperature -20°C to +85°C
Operating Humidity 5% to 90% RH, non-condensing
Storage Humidity 5% to 95% RH, non-condensing
Vibration 5 ~ 50Hz, acceleration 7.35 m/(s x s) on X, Y, and Z axis.
Cooling U Type (U-Chassis): 25CFM to achieve maximum power
E &
F Type (Enclosed with built-in fan): Self cooled by built-in fan.
MTBF 150,000 hours (according to MIL-HBK-217F) at 30°C. PHYSICAL SPECIFICATIONS
Weight U Type (U-Chassis): 1350 grams
E &
F Type (Enclosed with built-in fan): 1450 grams
Dimensions U Type (U-Chassis): 8(L) x 4.33(W) x 2.5(H) inches.
E Type (Enclosed with built-in fan):9.17(L) x 4.25(W) x 2.5(H) inches.
F Type (Enclosed with top built-in fan): 8(L) x 4.33(W) X 3.4(H) inches.
Warranty 2 years
SAFETY
Emissions FCC part15, CISPR 22 Class B, Conducted.
Safety Regulations Approved to UL60950-1, CSA C22.2 No. 60950-1-03, TUV EN60950-1, CE Mark (LVD) EN61000-3-2,3, and IEC61000-4 Series Regulations and CB.
OUTPUT VOLTAGE / CURRENT RATING CHART
Model Output Voltage
Range
Preset
Voltage
Output
Current
Regulation Ripple & Noise Output Power
PSRL5017Rx8-12N(I) 12 – 14 VDC 12 VDC 62.5A ±1% ±1% 750W PSRL5017Rx8-15N(I) 15 – 19 VDC 15 VDC 50A ±1% ±1% 750W PSRL5017Rx8-24N(I) 20 – 26 VDC 24 VDC 40A ±1% ±1% 800W PSRL5017Rx8-36N(I) 27 – 36 VDC 36 VDC 29.63A ±1% ±1% 800W PSRL5017Rx8-40N(I) 37 – 47 VDC 40 VDC 21.62A ±1% ±1% 800W PSRL5017Rx8-48N(I) 48 – 60 VDC 48 VDC 16.67A ±1% ±1% 800W
NOTES
1. PSRL5017R8-N Series is designated as PSRL5017Rxw-yz where x can be E (enclosed with end side built-in fan), U (U-Chassis with optional cover), or F (enclosed with top built-in fan), w = 8 for output power from 750W to 800W, y can be 12N, 15N, 24N, 36N, 40N, or 48N for output voltage, and z can be blank or I where I denote forced current sharing option (output with internal OR-ring diode). See PSRL5017R-N I Series for forced current sharing.
2. All output ranges are covered in agency certifications and preset voltage will be set as standard models. If any request is not preset
output, then please contact us in advance.
3. U-Chassis type needs external forced airflow min. 25CFM to achieve maximum power.
4. Ripple & noise are measured from 10KHZ to 20MHz bandwidth at output with parallel 0.1uF ceramic and 22uF electrolytic capacitors.
5. Providing peak power to 900W within 500uS for all models, longer duty duration need contact manufacturer.
6. 1% minimum load is required to maintain the ripple and regulation.
7. Cover is optional for U-Chassis Type. Please call factory for ordering details.
8. Output is fully isolated.
AC/DC Switching Power Supply MECHANICAL DRAWINGS
PSRL5017RU8-N Series (U-Chassis Type): 8(L) x 4.33(W) x 2.5(H) inches; Weight: 1350g; Option: Top Cover.
PSRL5017RE8-N Series (Enclosed with Built-in Fan Type): 9.17(L) x 4.25(W) x 2.5(H) inches; Weight: 1450g.
AC/DC Switching Power Supply
PSRL5017RF8-N Series (Enclosed with Top Built-in Fan Type): 8(L) x 4.33(W) x 3.4(H) inches; Weight: 1450g.
I/O CONNECTOR PIN ASSIGNMENT
AC Input Connector (CN1):
E Type: IEC320 or equivalent Snap-in mounting type or DINKLE Terminal block Part No. DT-35-A02W-03 (3 pin).
U & F Type: Mating Molex Part No. 09-91-0700 or equivalent (7 pin. 5 used) or Howder Terminal block Part No. HD-121-3P.
Output Connector (CN2):
Mating Molex Part No. 09-91-2000 (20 pin) or Howder Terminal block Part No. HD-121-8P (8 pin).
Output Pin Assignment:
Optional two type - Molex: VO+ (Pins 1-10 ), VO- (Pins 11-20) ; Howder: VO+ (Pins 1-4 ), VO- (Pins 5-8).
Logic signal connectors (CN3):
Mating JST XHP-7 or equivalent (CHYAO SHIUNN JS-2001-07).
Fan Drive:
12VDC/400mA Mating JST XHP-2 or equivalent (CHYAO SHIUNN JS-2001-02).
Mounting Inserts:
6-32, M4 4 Places individually with maximum penetration 0.2 inch on bottom side and 0.25 inch on both sides.
OUTPUT PIN CONNECTION Howder Molex
Vo+Pins 1 – 4 Pins 1 – 10Vo-
Pins 5 – 8
Pins 11 – 20