土木工程外文文献翻译

专业资料

学院：

专业：土木工程

姓名：

学号：

外文出处：Structural Systems to resist (用外文写)

Lateral loads

附件：1.外文资料翻译译文；2.外文原文。

附件1：外文资料翻译译文

抗侧向荷载的结构体系

常用的结构体系

若已测出荷载量达数千万磅重，那么在高层建筑设计中就没有多少可以进行极其复杂的构思余地了。确实，较好的高层建筑普遍具有构思简单、表现明晰的特点。

这并不是说没有进行宏观构思的余地。实际上，正是因为有了这种宏观的构思，新奇的高层建筑体系才得以发展，可能更重要的是：几年以前才出现的一些新概念在今天的技术中已经变得平常了。

如果忽略一些与建筑材料密切相关的概念不谈，高层建筑里最为常用的结构体系便可分为如下几类：

1.抗弯矩框架。

2.支撑框架，包括偏心支撑框架。

3.剪力墙，包括钢板剪力墙。

4.筒中框架。

5.筒中筒结构。

6.核心交互结构。

7. 框格体系或束筒体系。

特别是由于最近趋向于更复杂的建筑形式，同时也需要增加刚度以抵抗几力和地震力，大多数高层建筑都具有由框架、支撑构架、剪力墙和相关体系相结合而构成的体系。而且，就较高的建筑物而言，大多数都是由交互式构件组成三维陈列。

将这些构件结合起来的方法正是高层建筑设计方法的本质。其结合方式需要在考虑环境、功能和费用后再发展，以便提供促使建筑发展达到新高度的有效结构。这并

不是说富于想象力的结构设计就能够创造出伟大建筑。正相反，有许多例优美的建筑仅得到结构工程师适当的支持就被创造出来了，然而，如果没有天赋甚厚的建筑师的创造力的指导，那么，得以发展的就只能是好的结构，并非是伟大的建筑。无论如何，要想创造出高层建筑真正非凡的设计，两者都需要最好的。

虽然在文献中通常可以见到有关这七种体系的全面性讨论，但是在这里还值得进一步讨论。设计方法的本质贯穿于整个讨论。设计方法的本质贯穿于整个讨论中。

抗弯矩框架

抗弯矩框架也许是低，中高度的建筑中常用的体系，它具有线性水平构件和垂直构件在接头处基本刚接之特点。这种框架用作独立的体系，或者和其他体系结合起来使用，以便提供所需要水平荷载抵抗力。对于较高的高层建筑，可能会发现该本系不宜作为独立体系，这是因为在侧向力的作用下难以调动足够的刚度。

我们可以利用STRESS，STRUDL 或者其他大量合适的计算机程序进行结构分析。所谓的门架法分析或悬臂法分析在当今的技术中无一席之地，由于柱梁节点固有柔性，并且由于初步设计应该力求突出体系的弱点，所以在初析中使用框架的中心距尺寸设计是司空惯的。当然，在设计的后期阶段，实际地评价结点的变形很有必要。

支撑框架

支撑框架实际上刚度比抗弯矩框架强，在高层建筑中也得到更广泛的应用。这种体系以其结点处铰接或则接的线性水平构件、垂直构件和斜撑构件而具特色，它通常与其他体系共同用于较高的建筑，并且作为一种独立的体系用在低、中高度的建筑中。

尤其引人关注的是，在强震区使用偏心支撑框架。

此外，可以利用STRESS，STRUDL，或一系列二维或三维计算机分析程序中的任何一种进行结构分析。另外，初步分析中常用中心距尺寸。

剪力墙

剪力墙在加强结构体系刚性的发展过程中又前进了一步。该体系的特点是具有相当薄的，通常是（而不总是）混凝土的构件，这种构件既可提供结构强度，又可提供建筑物功能上的分隔。

在高层建筑中，剪力墙体系趋向于具有相对大的高宽经，即与宽度相比，其高度偏大。由于基础体系缺少应力，任何一种结构构件抗倾覆弯矩的能力都受到体系的宽度和构件承受的重力荷载的限制。由于剪力墙宽度狭狭窄受限，所以需要以某种方式加以扩大，以便提从所需的抗倾覆能力。在窗户需要量小的建筑物外墙中明显地使用了这种确有所需要宽度的体系。

钢结构剪力墙通常由混凝土覆盖层来加强以抵抗失稳，这在剪切荷载大的地方已得到应用。这种体系实际上比钢支撑经济，对于使剪切荷载由位于地面正上方区域内比较高的楼层向下移特别有效。这种体系还具有高延性之优点，这种特性在强震区特别重要。

由于这些墙内必然出同一些大孔，使得剪力墙体系分析变得错综复杂。可以通过桁架模似法、有限元法，或者通过利用为考虑剪力墙的交互作用或扭转功能设计的专门计处机程序进行初步分析。

框架或支撑式筒体结构：

框架或支撑式筒体最先应用于IBM公司在Pittsburgh的一幢办公楼，随后立即被应用于纽约双子座的110层世界贸易中心摩天大楼和其他的建筑中。这种系统有以下几个显著的特征：三维结构、支撑式结构、或由剪力墙形成的一个性质上差不多是圆柱体的闭合曲面，但又有任意的平面构成。由于这些抵抗侧向荷载的柱子差不多都被设置在整个系统的中心，所以整体的惯性得到提高，刚度也是很大的。

在可能的情况下，通过三维概念的应用、二维的类比，我们可以进行筒体结构的分析。不管应用那种方法，都必须考虑剪力滞后的影响。

这种最先在航天器结构中研究的剪力滞后出现后，对筒体结构的刚度是一个很大的限制。这种观念已经影响了筒体结构在60层以上建筑中的应用。设计者已经开发出了很多的技术，用以减小剪力滞后的影响，这其中最有名的是桁架的应用。框架或支撑式筒体在40层或稍高的建筑中找到了自己的用武之地。除了一些美观的考虑外，桁架几乎很少涉及与外墙联系的每个建筑功能，而悬索一般设置在机械的地板上，这就令机械体系设计师们很不赞成。但是，作为一个性价比较好的结构体系，桁架能充分发挥它的性能，所以它会得到设计师们持续的支持。由于其最佳位置正取决于所提供的桁架的数量，因此很多研究已经试图完善这些构件的位置。实验表明：由于这种结构体系的经济性并不十分受桁架位置的影响，所以这些桁架的位置主要取决于机械系统的完善，审美的要求，

筒中筒结构：

筒体结构系统能使外墙中的柱具有灵活性，用以抵抗颠覆和剪切力。“筒中筒”这个名字顾名思义就是在建筑物的核心承重部分又被包围了第二层的一系列柱子，它们被当作是框架和支撑筒来使用。配置第二层柱的目的是增强抗颠覆能力和增大侧移刚

度。这些筒体不是同样的功能，也就是说，有些筒体是结构的，而有些筒体是用来支撑的。

在考虑这种筒体时，清楚的认识和区别变形的剪切和弯曲分量是很重要的，这源于对梁的对比分析。在结构筒中，剪切构件的偏角和柱、纵梁（例如：结构筒中的网等）的弯曲有关，同时，弯曲构件的偏角取决于柱子的轴心压缩和延伸（例如：结构筒的边缘等）。在支撑筒中，剪切构件的偏角和对角线的轴心变形有关，而弯曲构件的偏角则与柱子的轴心压缩和延伸有关。

根据梁的对比分析，如果平面保持原形（例如：厚楼板），那么外层筒中柱的轴心压力就会与中心筒柱的轴心压力相差甚远，而且稳定的大于中心筒。但是在筒中筒结构的设计中，当发展到极限时，内部轴心压力会很高的，甚至远远大于外部的柱子。这种反常的现象是由于两种体系中的剪切构件的刚度不同。这很容易去理解，内筒可以看成是一个支撑（或者说是剪切刚性的）筒，而外筒可以看成是一个结构（或者说是剪切弹性的）筒。

核心交互式结构：

核心交互式结构属于两个筒与某些形式的三维空间框架相配合的筒中筒特殊情况。事实上，这种体系常用于那种外筒剪切刚度为零的结构。位于Pittsburgh的美国钢铁大楼证实了这种体系是能很好的工作的。在核心交互式结构中，内筒是一个支撑结构，外筒没有任何剪切刚度，而且两种结构体系能通过一个空间结构或“帽”式结构共同起作用。需要指出的是，如果把外部的柱子看成是一种从“帽”到基础的直线体系，这将是不合适的；根据支撑核心的弹性曲线，这些柱子只发挥了刚度的15%。同样需要指出的是，内柱中与侧向力有关的轴向力沿筒高度由拉力变为压力，同时变化点位于

筒高度的约5/8处。当然，外柱也传递相同的轴向力，这种轴向力低于作用在整个柱子高度的侧向荷载，因为这个体系的剪切刚度接近于零。

把内外筒相连接的空间结构、悬臂梁或桁架经常遵照一些规范来布置。美国电话电报总局就是一个布置交互式构件的生动例子。

1．结构体系长59.7米，宽28.6米，高183.3米。

2．布置了两个筒，每个筒的尺寸是9.4米×12.2米，在长方向上有27.4米的间隔。

3. 在短方向上内筒被支撑起来，但是在长方向上没有剪切刚度。

4. 环绕着建筑物布置了一个外筒。

5. 外筒是一个瞬时抵抗结构，但是在每个长方向的中心15.2米都没有剪切刚度。

6.在建筑的顶部布置了一个空间桁架构成的“帽式”结构。

7.在建筑的底部布置了一个相似的空间桁架结构。

8.由于外筒的剪切刚度在建筑的底部接近零，整个建筑基本上由两个钢板筒来支

持。

框格体系或束筒体系结构：

位于美国芝加哥的西尔斯大厦是箱式结构的经典之作，它由九个相互独立的筒组成的一个集中筒。由于西尔斯大厦包括九个几乎垂直的筒，而且筒在平面上无须相似，基本的结构体系在不规则形状的建筑中得到特别的应用。一些单个的筒高于建筑一点或很多是很常见的。事实上，这种体系的重要特征就在于它既有坚固的一面，也有脆弱的一面。

这种体系的脆弱，特别是在结构筒中，与柱子的压缩变形有很大的关系，柱子的

压缩变形有下式计算：

△=ΣfL/E

对于那些层高为3.66米左右和平均压力为138MPa的建筑，在荷载作用下每层柱子的压缩变形为15（12）/29000或1.9毫米。在第50层柱子会压缩94毫米，小于它未受压的长度。这些柱子在50层的时候和100层的时候的变形是不一样的，位于这两种体系之间接近于边缘的那些柱需要使这种不均匀的变形得以调解。

主要的结构工作都集中在布置中。在Melbourne的Rialto项目中，结构工程师发现至少有一幢建筑，很有必要垂直预压低高度的柱子，以便使柱不均匀的变形差得以调解，调解的方法近似于后拉伸法，即较短的柱转移重量到较高的邻柱上。

附件2：外文原文（复印件）

Structural Systems to resist lateral loads Commonly Used structural Systems

With loads measured in tens of thousands kips, there is little room in the design of high-rise buildings for excessively complex thoughts. Indeed, the better high-rise buildings carry the universal traits of simplicity of thought and clarity of expression.

It does not follow that there is no room for grand thoughts. Indeed, it is with such grand thoughts that the new family of high-rise buildings has evolved. Perhaps more important, the new co ncepts of but a few years ago have become commonplace in today’ s technology.

Omitting some concepts that are related strictly to the materials of construction, the most commonly used structural systems used in high-rise buildings can be categorized as follows:

1.Moment-resisting frames.

2.Braced frames, including eccentrically braced frames.

3.Shear walls, including steel plate shear walls.

4.Tube-in-tube structures.

5.Tube-in-tube structures.

6.Core-interactive structures.

7.Cellular or bundled-tube systems.

Particularly with the recent trend toward more complex forms, but in response also to the need for increased stiffness to resist the forces from wind and earthquake, most high-rise buildings have structural systems built up of combinations of frames, braced bents, shear walls, and related systems. Further, for the taller buildings, the majorities are composed of interactive elements in three-dimensional arrays.

The method of combining these elements is the very essence of the design process for high-rise buildings. These combinations need evolve in response to environmental, functional, and cost considerations so as to provide efficient structures that provoke the architectural development to new heights. This is not to say that imaginative structural design can create great architecture. To the contrary, many examples of fine architecture have been created with

only moderate support from the structural engineer, while only fine structure, not great architecture, can be developed without the genius and the leadership of a talented architect. In any event, the best of both is needed to formulate a truly extraordinary design of a high-rise building.

While comprehensive discussions of these seven systems are generally available in the literature, further discussion is warranted here .The essence of the design process is distributed throughout the discussion.

Moment-Resisting Frames

Perhaps the most commonly used system in low-to medium-rise buildings, the moment-resisting frame, is characterized by linear horizontal and vertical members connected essentially rigidly at their joints. Such frames are used as a stand-alone system or in combination with other systems so as to provide the needed resistance to horizontal loads. In the taller of high-rise buildings, the system is likely to be found inappropriate for a stand-alone system, this because of the difficulty in mobilizing sufficient stiffness under lateral forces.

Analysis can be accomplished by STRESS, STRUDL, or a host of other appropriate computer programs; analysis by the so-called portal method of the cantilever method has no place in today’s technology.

Because of the intrinsic flexibility of the column/girder intersection, and because preliminary designs should aim to highlight weaknesses of systems, it is not unusual to use center-to-center dimensions for the frame in the preliminary analysis. Of course, in the latter phases of design, a realistic appraisal in-joint deformation is essential.

Braced Frame s

The braced frame, intrinsically stiffer than the moment –resisting frame, finds also greater application to higher-rise buildings. The system is characterized by linear horizontal, vertical, and diagonal members, connected simply or rigidly at their joints. It is used commonly in conjunction with other systems for taller buildings and as a stand-alone system in low-to medium-rise buildings.

While the use of structural steel in braced frames is common, concrete frames are more likely to be of the larger-scale variety.

Of special interest in areas of high seismicity is the use of the eccentric braced frame.

Again, analysis can be by STRESS, STRUDL, or any one of a series of two –or three dimensional analysis computer programs. And again, center-to-center dimensions are used commonly in the preliminary analysis.

Shear walls

The shear wall is yet another step forward along a progression of ever-stiffer structural systems. The system is characterized by relatively thin, generally (but not always) concrete elements that provide both structural strength and separation between building functions.

In high-rise buildings, shear wall systems tend to have a relatively high aspect ratio, that is, their height tends to be large compared to their width. Lacking tension in the foundation system, any structural element is limited in its ability to resist overturning moment by the width of the system and by the gravity load supported by the element. Limited to a narrow overturning, One

obvious use of the system, which does have the needed width, is in the exterior walls of building, where the requirement for windows is kept small.

Structural steel shear walls, generally stiffened against buckling by a concrete overlay, have found application where shear loads are high. The system, intrinsically more economical than steel bracing, is particularly effective in carrying shear loads down through the taller floors in the areas immediately above grade. The sys tem has the further advantage of having high ductility a feature of particular importance in areas of high seismicity.

The analysis of shear wall systems is made complex because of the inevitable presence of large openings through these walls. Preliminary analysis can be by truss-analogy, by the finite element method, or by making use of a proprietary computer program designed to consider the interaction, or coupling, of shear walls.

Framed or Braced Tubes

The concept of the framed or braced or braced tube erupted into the technology with the IBM Building in Pittsburgh, but was followed immediately with the twin 110-story towers of the World Trade Center, New York and a number of other buildings .The system is characterized by three –dimensional frames, braced frames, or shear walls, forming a closed surface more or less cylindrical in nature, but of nearly any plan configuration. Because those columns that resist lateral forces are placed as far as possible from the cancroids of the system, the overall moment of inertia is increased and stiffness is very high.

The analysis of tubular structures is done using three-dimensional concepts, or by two- dimensional analogy, where possible, whichever method is used, it must be capable of

accounting for the effects of shear lag.

The presence of shear lag, detected first in aircraft structures, is a serious limitation in the stiffness of framed tubes. The concept has limited recent applications of framed tubes to the shear of 60 stories. Designers have developed various techniques for reducing the effects of shear lag, most noticeably the use of belt trusses. This system finds application in buildings perhaps 40stories and higher. However, except for possible aesthetic considerations, belt trusses interfere with nearly every building function associated with the outside wall; the trusses are placed often at mechanical floors, mush to the disapproval of the designers of the mechanical systems. Nevertheless, as a cost-effective structural system, the belt truss works well and will likely find continued approval from designers. Numerous studies have sought to optimize the location of these trusses, with the optimum location very dependent on the number of trusses provided. Experience would indicate, however, that the location of these trusses is provided by the optimization of mechanical systems and by aesthetic considerations, as the economics of the structural system is not highly sensitive to belt truss location.

Tube-in-Tube Structures

The tubular framing system mobilizes every column in the exterior wall in resisting over-turning and shearing forces. The term‘tube-in-tube’is largely self-explanatory in that a second ring of columns, the ring surrounding the central service core of the building, is used as an inner framed or braced tube. The purpose of the second tube is to increase resistance to over turning and to increase lateral stiffness. The tubes need not be of the same character; that is, one tube could be framed, while the other could be braced.

In considering this system, is important to understand clearly the difference between the shear and the flexural components of deflection, the terms being taken from beam analogy. In a framed tube, the shear component of deflection is associated with the bending deformation of columns and girders (i.e, the webs of the framed tube) while the flexural component is associated with the axial shortening and lengthening of columns (i.e, the flanges of the framed tube). In a braced tube, the shear component of deflection is associated with the axial deformation of diagonals while the flexural component of deflection is associated with the axial shortening and lengthening of columns.

Following beam analogy, if plane surfaces remain plane (i.e, the floor slabs),then axial stresses in the columns of the outer tube, being farther form the neutral axis, will be substantially larger than the axial stresses in the inner tube. However, in the tube-in-tube design, when optimized, the axial stresses in the inner ring of columns may be as high, or even higher, than the axial stresses in the outer ring. This seeming anomaly is associated with differences in the shearing component of stiffness between the two systems. This is easiest to under-stand where the inner tube is conceived as a braced (i.e, shear-stiff) tube while the outer tube is conceived as a framed (i.e, shear-flexible) tube.

Core Interactive Structures

Core interactive structures are a special case of a tube-in-tube wherein the two tubes are coupled together with some form of three-dimensional space frame. Indeed, the system is used often wherein the shear stiffness of the outer tube is zero. The United States Steel Building, Pittsburgh, illustrates the system very well. Here, the inner tube is a braced frame, the outer tube

has no shear stiffness, and the two systems are coupled if they were considered as systems passing in a straight line from the “hat” structure. Note that the exterior columns would be improperly modeled if they were considered as systems passing in a straight line from the “hat” to the foundations; these columns are perhaps 15% stiffer as they follow the elastic curve of the braced core. Note also that the axial forces associated with the lateral forces in the inner columns change from tension to compression over the height of the tube, with the inflection point at about 5/8 of the height of the tube. The outer columns, of course, carry the same axial force under lateral load for the full height of the columns because the columns because the shear stiffness of the system is close to zero.

The space structures of outrigger girders or trusses, that connect the inner tube to the outer tube, are located often at several levels in the building. The AT&T headquarters is an example of an astonishing array of interactive elements:

1.The structural system is 94 ft (28.6m) wide, 196ft(59.7m) long, and 601ft (183.3m) high.

2.Two inner tubes are provided, each 31ft(9.4m) by 40 ft (12.2m), centered 90 ft (27.4m)

apart in the long direction of the building.

3.The inner tubes are braced in the short direction, but with zero shear stiffness in the long

direction.

4. A single outer tube is supplied, which encircles the building perimeter.

5.The outer tube is a moment-resisting frame, but with zero shear stiffness for the center50ft

(15.2m) of each of the long sides.

6. A space-truss hat structure is provided at the top of the building.

7. A similar space truss is located near the bottom of the building

8.The entire assembly is laterally supported at the base on twin steel-plate tubes, because

the shear stiffness of the outer tube goes to zero at the base of the building.

Cellular structures

A classic example of a cellular structure is the Sears Tower, Chicago, a bundled tube structure of nine separate tubes. While the Sears Tower contains nine nearly identical tubes, the basic structural system has special application for buildings of irregular shape, as the several tubes need not be similar in plan shape, It is not uncommon that some of the individual tubes one of the strengths and one of the weaknesses of the system.

This special weakness of this system, particularly in framed tubes, has to do with the concept of differential column shortening. The shortening of a column under load is given by the expression

△=ΣfL/E

For buildings of 12 ft (3.66m) floor-to-floor distances and an average compressive stress of 15 ksi (138MPa), the shortening of a column under load is 15 (12)(12)/29,000 or 0.074in (1.9mm) per story. At 50 stories, the column will have shortened to 3.7 in. (94mm) less than its unstressed length. Where one cell of a bundled tube system is, say, 50stories high and an adjacent cell is, say, 100stories high, those columns near the boundary between .the two systems need to have this differential deflection reconciled.

Major structural work has been found to be needed at such locations. In at least one building, the Rialto Project, Melbourne, the structural engineer found it necessary to vertically pre-stress the lower height columns so as to reconcile the differential deflections of columns

in close proximity with the post-tensioning of the shorter column simulating the weight to be added on to adjacent, higher columns.

土木工程类专业英文文献及翻译

PA VEMENT PROBLEMS CAUSED BY COLLAPSIBLE SUBGRADES By Sandra L. Houston,1 Associate Member, ASCE (Reviewed by the Highway Division) ABSTRACT: Problem subgrade materials consisting of collapsible soils are com- mon in arid environments, which have climatic conditions and depositional and weathering processes favorable to their formation. Included herein is a discussion of predictive techniques that use commonly available laboratory equipment and testing methods for obtaining reliable estimates of the volume change for these problem soils. A method for predicting relevant stresses and corresponding collapse strains for typical pavement subgrades is presented. Relatively simple methods of evaluating potential volume change, based on results of familiar laboratory tests, are used. INTRODUCTION When a soil is given free access to water, it may decrease in volume, increase in volume, or do nothing. A soil that increases in volume is called a swelling or expansive soil, and a soil that decreases in volume is called a collapsible soil. The amount of volume change that occurs depends on the soil type and structure, the initial soil density, the imposed stress state, and the degree and extent of wetting. Subgrade materials comprised of soils that change volume upon wetting have caused distress to highways since the be- ginning of the professional practice and have cost many millions of dollars in roadway repairs. The prediction of the volume changes that may occur in the field is the first step in making an economic decision for dealing with these problem subgrade materials. Each project will have different design considerations, economic con- straints, and risk factors that will have to be taken into account. However, with a reliable method for making volume change predictions, the best design relative to the subgrade soils becomes a matter of economic comparison, and a much more rational design approach may be made. For example, typical techniques for dealing with expansive clays include: (1) In situ treatments with substances such as lime, cement, or fly-ash; (2) seepage barriers and/ or drainage systems; or (3) a computing of the serviceability loss and a mod- ification of the design to "accept" the anticipated expansion. In order to make the most economical decision, the amount of volume change (especially non- uniform volume change) must be accurately estimated, and the degree of road roughness evaluated from these data. Similarly, alternative design techniques are available for any roadway problem. The emphasis here will be placed on presenting economical and simple methods for: (1) Determining whether the subgrade materials are collapsible; and (2) estimating the amount of volume change that is likely to occur in the 'Asst. Prof., Ctr. for Advanced Res. in Transp., Arizona State Univ., Tempe, AZ 85287. Note. Discussion open until April 1, 1989. To extend the closing date one month,

土木工程外文文献及翻译

本科毕业设计 外文文献及译文 文献、资料题目：Designing Against Fire Of Building 文献、资料来源：国道数据库 文献、资料发表（出版）日期：2008.3.25 院（部）：土木工程学院 专业：土木工程 班级：土木辅修091 姓名：武建伟 学号：2008121008 指导教师：周学军、李相云 翻译日期： 20012.6.1

外文文献: Designing Against Fire Of Buliding John Lynch ABSTRACT: This paper considers the design of buildings for fire safety. It is found that fire and the associ- ated effects on buildings is significantly different to other forms of loading such as gravity live loads, wind and earthquakes and their respective effects on the building structure. Fire events are derived from the human activities within buildings or from the malfunction of mechanical and electrical equipment provided within buildings to achieve a serviceable environment. It is therefore possible to directly influence the rate of fire starts within buildings by changing human behaviour, improved maintenance and improved design of mechanical and electrical systems. Furthermore, should a fire develops, it is possible to directly influence the resulting fire severity by the incorporation of fire safety systems such as sprinklers and to provide measures within the building to enable safer egress from the building. The ability to influence the rate of fire starts and the resulting fire severity is unique to the consideration of fire within buildings since other loads such as wind and earthquakes are directly a function of nature. The possible approaches for designing a building for fire safety are presented using an example of a multi-storey building constructed over a railway line. The design of both the transfer structure supporting the building over the railway and the levels above the transfer structure are considered in the context of current regulatory requirements. The principles and assumptions associ- ated with various approaches are discussed. 1 INTRODUCTION Other papers presented in this series consider the design of buildings for gravity loads, wind and earthquakes.The design of buildings against such load effects is to a large extent covered by engineering based standards referenced by the building regulations. This is not the case, to nearly the same extent, in the

土木工程外文翻译

转型衰退时期的土木工程研究 Sergios Lambropoulosa[1], John-Paris Pantouvakisb, Marina Marinellic 摘要 最近的全球经济和金融危机导致许多国家的经济陷入衰退，特别是在欧盟的周边。这些国家目前面临的民用建筑基础设施的公共投资和私人投资显著收缩，导致在民事特别是在民用建筑方向的失业。因此，在所有国家在经济衰退的专业发展对于土木工程应届毕业生来说是努力和资历的不相称的研究，因为他们很少有机会在实践中积累经验和知识，这些逐渐成为过时的经验和知识。在这种情况下，对于技术性大学在国家经济衰退的计划和实施的土木工程研究大纲的一个实质性的改革势在必行。目的是使毕业生拓宽他们的专业活动的范围，提高他们的就业能力。 在本文中，提出了土木工程研究课程的不断扩大，特别是在发展的光毕业生的潜在的项目，计划和投资组合管理。在这个方向上，一个全面的文献回顾，包括ASCE体为第二十一世纪，IPMA的能力的基础知识，建议在其他：显著增加所提供的模块和项目管理在战略管理中添加新的模块，领导行为，配送管理，组织和环境等；提供足够的专业训练五年的大学的研究；并由专业机构促进应届大学生认证。建议通过改革教学大纲为土木工程研究目前由国家技术提供了例证雅典大学。 1引言 土木工程研究（CES）蓬勃发展，是在第二次世界大战后。土木工程师的出现最初是由重建被摧毁的巨大需求所致，目的是更多和更好的社会追求。但是很快，这种演变一个长期的趋势，因为政府为了努力实现经济发展，采取了全世界的凯恩斯主义的理论，即公共基础设施投资作为动力。首先积极的结果导致公民为了更好的生活条件（住房，旅游等）和增加私人投资基础设施而创造机会。这些现象再国家的发展中尤为为明显。虽然前景并不明朗（例如，世界石油危机在70年代），在80年代领先的国家采用新自由主义经济的方法（如里根经济政策），这是最近的金融危机及金融危机造成的后果（即收缩的基础设施投资，在技术部门的高失业率），消除发展前途无限的误区。 技术教育的大学所认可的大量研究土木工程部。旧学校拓展专业并且新的学校建成，并招收许多学生。由于高的职业声望，薪酬，吸引高质量的学校的学生。在工程量的增加和科学技术的发展，导致到极强的专业性，无论是在研究还是工作当中。结构工程师，液压工程师，交通工程师等，都属于土木工程。试图在不同的国家采用专业性的权利，不同的解决方案，，从一个统一的大学学历和广泛的专业化的一般职业许可证。这个问题在许多其他行业成为关键。国际专业协会的专家和机构所确定的国家性检查机构，经过考试后，他们证明不仅是行业的新来者，而且专家通过时间来确定进展情况。尽管在很多情况下，这些证书虽然没有国家接受，他们赞赏和公认的世界。 在试图改革大学研究（不仅在土木工程）更接近市场需求的过程中，欧盟确定了1999博洛尼亚宣言，它引入了一个二能级系统。第一级度（例如，一个三年的学士）是进入

零售企业营销策略中英文对照外文翻译文献

零售企业营销策略中英文对照外文翻译文献(文档含英文原文和中文翻译)

译文： 零售企业的营销策略 Philip Kotlor 今天的零售商为了招徕和挽留顾客，急欲寻找新的营销策略。过去，他们挽留顾客的方法是销售特别的或独特的花色品种，提供比竞争对手更多更好的服务提供商店信用卡是顾客能赊购商品。可是，现在这一切都已变得面目全非了。现在，诸如卡尔文·克连，依佐和李维等全国性品牌，不仅在大多数百货公司及其专营店可以看到，并且也可以在大型综合商场和折扣商店可以买到。全国性品牌的生产商为全力扩大销售量，它们将贴有品牌的商品到处销售。结果是零售商店的面貌越来越相似。 在服务项目上的分工差异在逐渐缩小。许多百货公司削减了服务项目，而许多折扣商店却增加了服务项目。顾客变成了精明的采购员，对价格更加敏感。他们看不出有什么道理要为相同的品牌付出更多的钱，特别是当服务的差别不大或微不足道时。由于银行信用卡越来越被所有的商家接受，他们觉得不必从每个商店赊购商品。 百货商店面对着日益增加的价格的折扣店和专业商店的竞争，准备东山再起。历史上居于市中心的许多商店在郊区购物中心开设分店，那里有宽敞的停车场，购买者来自人口增长较快并且有较高收入的地区。其他一些则对其商店形式进行改变，有些则试用邮购盒电话订货的方法。超级市场面对的是超级商店的竞争，它们开始扩大店面，经营大量的品种繁多的商品和提高设备等级，超级市场还增加了它们的促销预算，大量转向私人品牌，从而增加盈利。 现在，我们讨论零售商在目标市场、产品品种和采办、服务以及商店气氛、定价、促销和销售地点等方面的营销策略。 一、目标市场 零售商最重要的决策时确定目标市场。当确定目标市场并且勾勒出轮廓时，零售商才能对产品分配、商店装饰、广告词和广告媒体、价格水平等作出一致的决定。如沃尔玛的目标市场相当明确：

土木工程岩土类毕业设计外文翻译

姓名： 学号： 10447425 X X 大学 毕业设计（论文）外文翻译 （2014届） 外文题目Developments in excavation bracing systems 译文题目开挖工程支撑体系的发展 外文出处Tunnelling and Underground Space Technology 31 (2012) 107–116 学生XXX 学院XXXX 专业班级XXXXX 校内指导教师XXX 专业技术职务XXXXX 校外指导老师专业技术职务 二○一三年十二月

开挖工程支撑体系的发展 1.引言 几乎所有土木工程建设项目（如建筑物，道路，隧道，桥梁，污水处理厂，管道，下水道）都涉及泥土挖掘的一些工程量。往往由于由相邻的结构，特性线，或使用权空间的限制，必须要一个土地固定系统，以允许土壤被挖掘到所需的深度。历史上，许多挖掘支撑系统已经开发出来。其中，现在比较常见的几种方法是：板桩，钻孔桩墙，泥浆墙。 土地固定系统的选择是由技术性能要求和施工可行性（例如手段，方法）决定的，包括执行的可靠性，而成本考虑了这些之后，其他问题也得到解决。通常环境后果（用于处理废泥浆和钻井液如监管要求）也非常被关注（邱阳、1998）。 土地固定系统通常是建设项目的较大的一个组成部分。如果不能按时完成项目，将极大地影响总成本。通常首先建造支撑，在许多情况下，临时支撑系统是用于支持在挖掘以允许进行不断施工，直到永久系统被构造。临时系统可以被去除或留在原处。 打桩时，因撞击或振动它们可能会被赶入到位。在一般情况下，振动是最昂贵的方法，但只适合于松散颗粒材料，土壤中具有较高电阻（例如，通过鹅卵石）的不能使用。采用打入桩系统通常是中间的成本和适合于软沉积物（包括粘性和非粘性），只要该矿床是免费的鹅卵石或更大的岩石。 通常，垂直元素（例如桩）的前安装挖掘工程和水平元件（如内部支撑或绑回）被安装为挖掘工程的进行下去，从而限制了跨距长度，以便减少在垂直开发弯矩元素。在填充情况下，桩可先设置，从在斜坡的底部其嵌入悬挑起来，安装作为填充进步水平元素（如搭背或土钉）。如果滞后是用来保持垂直元素之间的土壤中，它被安装为挖掘工程的进行下去，或之前以填补位置。 吉尔- 马丁等人（2010）提供了一个数值计算程序，以获取圆形桩承受轴向载荷和统一标志（如悬臂桩）的单轴弯矩的最佳纵筋。他们开发的两种优化流程：用一个或两个直径为纵向钢筋。优化增强模式允许大量减少的设计要求钢筋的用量，这些减少纵向钢筋可达到50％相对传统的，均匀分布的加固方案。 加固桩集中纵向钢筋最佳的位置在受拉区。除了节约钢筋，所述非对称加强钢筋图案提高抗弯刚度，通过增加转动惯量的转化部分的时刻。这种增加的刚性可能会在一段时间内增加的变形与蠕变相关的费用。评估相对于传统的非对称加强桩的优点，对称，钢筋桩被服务的条件下全面测试来完成的，这种试验是为了验证结构的可行性和取得的变形的原位测量。 基于现场试验中，用于优化的加强图案的优点浇铸钻出孔（CIDH）在巴塞罗那的

土木工程外文文献翻译

专业资料 学院： 专业：土木工程 姓名： 学号： 外文出处：Structural Systems to resist (用外文写) Lateral loads 附件：1.外文资料翻译译文；2.外文原文。

附件1：外文资料翻译译文 抗侧向荷载的结构体系 常用的结构体系 若已测出荷载量达数千万磅重，那么在高层建筑设计中就没有多少可以进行极其复杂的构思余地了。确实，较好的高层建筑普遍具有构思简单、表现明晰的特点。 这并不是说没有进行宏观构思的余地。实际上，正是因为有了这种宏观的构思，新奇的高层建筑体系才得以发展，可能更重要的是：几年以前才出现的一些新概念在今天的技术中已经变得平常了。 如果忽略一些与建筑材料密切相关的概念不谈，高层建筑里最为常用的结构体系便可分为如下几类： 1.抗弯矩框架。 2.支撑框架，包括偏心支撑框架。 3.剪力墙，包括钢板剪力墙。 4.筒中框架。 5.筒中筒结构。 6.核心交互结构。 7. 框格体系或束筒体系。 特别是由于最近趋向于更复杂的建筑形式，同时也需要增加刚度以抵抗几力和地震力，大多数高层建筑都具有由框架、支撑构架、剪力墙和相关体系相结合而构成的体系。而且，就较高的建筑物而言，大多数都是由交互式构件组成三维陈列。 将这些构件结合起来的方法正是高层建筑设计方法的本质。其结合方式需要在考虑环境、功能和费用后再发展，以便提供促使建筑发展达到新高度的有效结构。这并

不是说富于想象力的结构设计就能够创造出伟大建筑。正相反，有许多例优美的建筑仅得到结构工程师适当的支持就被创造出来了，然而，如果没有天赋甚厚的建筑师的创造力的指导，那么，得以发展的就只能是好的结构，并非是伟大的建筑。无论如何，要想创造出高层建筑真正非凡的设计，两者都需要最好的。 虽然在文献中通常可以见到有关这七种体系的全面性讨论，但是在这里还值得进一步讨论。设计方法的本质贯穿于整个讨论。设计方法的本质贯穿于整个讨论中。 抗弯矩框架 抗弯矩框架也许是低，中高度的建筑中常用的体系，它具有线性水平构件和垂直构件在接头处基本刚接之特点。这种框架用作独立的体系，或者和其他体系结合起来使用，以便提供所需要水平荷载抵抗力。对于较高的高层建筑，可能会发现该本系不宜作为独立体系，这是因为在侧向力的作用下难以调动足够的刚度。 我们可以利用STRESS，STRUDL 或者其他大量合适的计算机程序进行结构分析。所谓的门架法分析或悬臂法分析在当今的技术中无一席之地，由于柱梁节点固有柔性，并且由于初步设计应该力求突出体系的弱点，所以在初析中使用框架的中心距尺寸设计是司空惯的。当然，在设计的后期阶段，实际地评价结点的变形很有必要。 支撑框架 支撑框架实际上刚度比抗弯矩框架强，在高层建筑中也得到更广泛的应用。这种体系以其结点处铰接或则接的线性水平构件、垂直构件和斜撑构件而具特色，它通常与其他体系共同用于较高的建筑，并且作为一种独立的体系用在低、中高度的建筑中。

土木工程外文翻译.doc

项目成本控制 一、引言 项目是企业形象的窗口和效益的源泉。随着市场竞争日趋激烈，工程质量、文明施工要求不断提高，材料价格波动起伏，以及其他种种不确定因素的影响，使得项目运作处于较为严峻的环境之中。由此可见项目的成本控制是贯穿在工程建设自招投标阶段直到竣工验收的全过程，它是企业全面成本管理的重要环节，必须在组织和控制措施上给于高度的重视，以期达到提高企业经济效益的目的。 二、概述 工程施工项目成本控制，指在项目成本在成本发生和形成过程中，对生产经营所消耗的人力资源、物资资源和费用开支，进行指导、监督、调节和限制，及时预防、发现和纠正偏差从而把各项费用控制在计划成本的预定目标之内，以达到保证企业生产经营效益的目的。 三、施工企业成本控制原则 施工企业的成本控制是以施工项目成本控制为中心，施工项目成本控制原则是企业成本管理的基础和核心，施工企业项目经理部在对项目施工过程进行成本控制时，必须遵循以下基本原则。 3.1 成本最低化原则。施工项目成本控制的根本目的，在于通过成本管理的各种手段，促进不断降低施工项目成本，以达到可能实现最低的目标成本的要求。在实行成本最低化原则时，应注意降低成本的可能性和合理的成本最低化。一方面挖掘各种降低成本的能力，使可能性变为现实；另一方面要从实际出发，制定通过主观努力可能达到合理的最低成本水平。 3.2 全面成本控制原则。全面成本管理是全企业、全员和全过程的管理，亦称“三全”管理。项目成本的全员控制有一个系统的实质性内容，包括各部门、各单位的责任网络和班组经济核算等等，应防止成本控制人人有责，人人不管。项目成本的全过程控制要求成本控制工作要随着项目施工进展的各个阶段连续 进行，既不能疏漏，又不能时紧时松，应使施工项目成本自始至终置于有效的控制之下。 3.3 动态控制原则。施工项目是一次性的，成本控制应强调项目的中间控制，即动态控制。因为施工准备阶段的成本控制只是根据施工组织设计的具体内容确

市场营销_外文翻译_外文文献_英文文献_顾客满意策略与顾客满意

顾客满意策略与顾客满意营销 原文来源：《Marketing Customer Satisfaction 》自20世纪八十年代末以来, 顾客满意战略已日益成为各国企业占有更多的顾客份额, 获得竞争优势的整体经营手段。 一、顾客满意策略是现代企业获得顾客“货币选票”的法宝随着时代的变迁, 社会物质财富的极大充裕, 顾客中的主体———消费者的需求也先后跨越了物质缺乏的时代、追求数量的时代、追求品质的时代, 到了20世纪八十年代末进入了情感消费时代。在我国, 随着经济的高速发展,我们也已迅速跨越了物质缺乏时代、追求数量的时代乃至追求品质的时代, 到今天也逐步迈进情感消费时代。在情感消费时代, 各企业的同类产品早已达到同时、同质、同能、同价, 消费者追求的已不再是质量、功能和价格, 而是舒适、便利、安全、安心、速度、跃动、环保、清洁、愉快、有趣等,消费者日益关注的是产品能否为自己的生活带来活力、充实、舒适、美感和精神文化品位, 以及超越消费者期望值的售前、售中、售后服务和咨询。也就是说, 今天人们所追求的是具有“心的满足感和充实感”的商品, 是高附加值的商品和服务,追求价值观和意识多元化、个性化和无形的满足感的时代已经来临。 与消费者价值追求变化相适应的企业间的竞争, 也由产品竞争、价格竞争、技术竞争、广告竞争、品牌竞争发展到现今的形象竞争、信誉竞争、文化竞争和服务竞争, 即顾客满意竞争。这种竞争是企业在广角度、宽领域的时空范围内展开的高层次、体现综合实力的竞争。它包括组织创新力、技术创新力、管理创新力、产业预见力、产品研发力、员工向心力、服务顾客力、顾客亲和力、同行认同力、社会贡献力、公关传播沟通力、企业文化推动力、环境适应力等等。这些综合形象力和如何合成综合持久的竞争力, 这就是CSft略所要解决的问题。CS寸代,企业不再以“自己为中心”,而是以“顾客为中心”；“顾客为尊”、“顾客满意”不再是流于形式的口号, 而是以实实在在的行动为基础的企业经营的一门新哲学。企业不再以质量达标, 自己满意为经营理念, 而是以顾客满意, 赢得顾客高忠诚度为经营理念。企业经营策略的焦点不再以争取或保持市场占有率为主, 而是以争取顾客满意为经营理念。因此, 营销策略的重心不再放在竞争对手身上而是放在顾客身上, 放在顾客现实的、潜在的需求上。当企业提供的产品和服务达到了顾客事先的期望值, 顾客就基本满意；如果远远超越顾客的期望值, 且远远高于其他同行, 顾客才真正满意；如果企业能不断地或长久地令顾客满意, 顾客就会忠诚。忠诚的顾客不仅会经常性地重复购买, 还会购买企业其它相关的产品或服务；忠诚的顾客不仅会积极向别人推荐他所买的产品, 而且对企业竞争者的促销活动具有免疫能力一个不满意的顾客会将不满意告诉16-20个人, 而每一个被告知者会再传播给12-15个人。这样, 一个不满意者会影响到二、三百人。在互联网普及的今天, 其影响则更大。据美国汽车业的调查, 一个满意者会引发8笔潜在的生意, 其中至少有一笔会成交。而另一项调查表明, 企业每增加5%的忠诚顾客, 利润就会增长25%-95%。一个企业的80%的利润来自20%的忠诚顾客；而获取一个新顾客的成本是维持一个老顾客成本的6倍。所以,美国著名学者唐?佩 珀斯指出: 决定一个企业成功与否的关键不是市场份额, 而是在于顾客份额。 于是, 企业纷纷通过广泛细致的市场调研、与消费者直接接触、顾客信息反馈等方式来了解顾客在各方面的现实需求和潜在需求。依靠对企业满意忠诚的销售、服务人员, 定期、定量地对顾客满意度进行综合测定, 以便准确地把握企业经营中与“顾客满意” 目标的差距及其重点领域, 从而进一步改善企业的经营活动。依靠高亲和力的企业文化、高效率的人文管理和全员共同努力, 不断地向顾客提供高附加值的产品, 高水准的亲情般的服

土木工程专业外文文献及翻译

（ 二 〇 一 二 年 六 月 外文文献及翻译 题 目： About Buiding on the Structure Design 学生姓名： 学 院：土木工程学院 系 别：建筑工程系 专 业：土木工程(建筑工程方向) 班 级：土木08-4班 指导教师：

英文原文： Building construction concrete crack of prevention and processing Abstract The crack problem of concrete is a widespread existence but again difficult in solve of engineering actual problem, this text carried on a study analysis to a little bit familiar crack problem in the concrete engineering, and aim at concrete the circumstance put forward some prevention, processing measure. Keyword:Concrete crack prevention processing Foreword Concrete's ising 1 kind is anticipate by the freestone bone, cement, water and other mixture but formation of the in addition material of quality brittleness not and all material.Because the concrete construction transform with oneself, control etc. a series problem, harden model of in the concrete existence numerous tiny hole, spirit cave and tiny crack, is exactly because these beginning start blemish of existence just make the concrete present one some not and all the characteristic of quality.The tiny crack is a kind of harmless crack and accept concrete heavy, defend Shen and a little bit other use function not a creation to endanger.But after the concrete be subjected to lotus carry, difference in temperature etc. function, tiny crack would continuously of expand with connect, end formation we can see without the

差异化营销策略外文文献翻译

文献出处: Dalman, M. Deniz, and Junhong Min. "Marketing Strategy for Unusual Brand Differentiation: Trivial Attribute Effect." International Journal of Marketing Studies 6.5 (2014): 63-72. 原文 Marketing Strategy for Unusual Brand Differentiation: Trivial Attribute Effect Dalman, M. Deniz & Junhong Min Abstract This research investigates that brand differentiation creating superior values can be achieved not only by adding meaningful attributes but also meaningless attributes, which is called "trivial attribute effect." Two studies provided empirical evidences as following; first, trivial attribute effect creates a strong brand differentiation even after subjects realize that trivial attribute has no value. Second, trivial attribute effect is more pronounced in hedonic service category compared to the utilitarian category. Last, the amount of willingness to pay is higher when trivial attribute is presented and evaluated in joint evaluation mode than separate evaluation mode. Finally, we conclude with discussion and provide suggestions for further research. Keywords: brand differentiation, evaluation mode, service industry, trivial attribute Introduction Problem Definition Perhaps the most important factor for new product success is to create the meaningful brand differentiation that provides customers with superior values beyond what the competitors can offer in the same industry (Porter, 1985). Not surprisingly, more than 50 percent of annual sales in consumer product industries including automobiles, biotechnology, computer software, and pharmaceuticals are attributed to such meaningful brand differentiation by including new or noble attributes (Schilling &Hill, 1998). However, the brand differentiation that increases consumer preference is not only by introducing meaningful attributes but also meaningless attributes. For

土木工程毕业设计外文翻译最终中英文

7 Rigid-Frame Structures A rigid-frame high-rise structure typically comprises parallel or orthogonally arranged bents consisting of columns and girders with moment resistant joints. Resistance to horizontal loading is provided by the bending resistance of the columns, girders, and joints. The continuity of the frame also contributes to resisting gravity loading, by reducing the moments in the girders. The advantages of a rigid frame are the simplicity and convenience of its rectangular form.Its unobstructed arrangement, clear of bracing members and structural walls, allows freedom internally for the layout and externally for the fenestration. Rig id frames are considered economical for buildings of up to' about 25 stories, above which their drift resistance is costly to control. If, however, a rigid frame is combined with shear walls or cores, the resulting structure is very much stiffer so that its height potential may extend up to 50 stories or more. A flat plate structure is very similar to a rigid frame, but with slabs replacing the girders As with a rigid frame, horizontal and vertical loadings are resisted in a flat plate structure by the flexural continuity between the vertical and horizontal components. As highly redundant structures, rigid frames are designed initially on the basis of approximate analyses, after which more rigorous analyses and checks can be made. The procedure may typically inc lude the following stages: 1. Estimation of gravity load forces in girders and columns by approximate method. 2. Preliminary estimate of member sizes based on gravity load forces with arbitrary increase in sizes to allow for horizontal loading. 3. Approximate allocation of horizontal loading to bents and preliminary analysis of member forces in bents. 4. Check on drift and adjustment of member sizes if necessary. 5. Check on strength of members for worst combination of gravity and horizontal loading, and adjustment of member sizes if necessary. 6. Computer analysis of total structure for more accurate check on member strengths and drift, with further adjustment of sizes where required. This stage may include the second-order P-Delta effects of gravity loading on the member forces and drift.. 7. Detailed design of members and connections.

土木工程外文翻译参考3篇

学校 毕业设计（论文）附件 外文文献翻译 学号： xxxxx 姓名： xxx 所在系别： xxxxx 专业班级： xxx 指导教师： xxxx 原文标题： Building construction concrete crack of prevention and processing 2012年月日 .

建筑施工混凝土裂缝的预防与处理1 摘要 混凝土的裂缝问题是一个普遍存在而又难于解决的工程实际问题，本文对混凝土工程中常见的一些裂缝问题进行了探讨分析，并针对具体情况提出了一些预防、处理措施。 关键词：混凝土裂缝预防处理 前言 混凝土是一种由砂石骨料、水泥、水及其他外加材料混合而形成的非均质脆性材料。由于混凝土施工和本身变形、约束等一系列问题，硬化成型的混凝土中存在着众多的微孔隙、气穴和微裂缝，正是由于这些初始缺陷的存在才使混凝土呈现出一些非均质的特性。微裂缝通常是一种无害裂缝，对混凝土的承重、防渗及其他一些使用功能不产生危害。但是在混凝土受到荷载、温差等作用之后，微裂缝就会不断的扩展和连通，最终形成我们肉眼可见的宏观裂缝，也就是混凝土工程中常说的裂缝。 混凝土建筑和构件通常都是带缝工作的，由于裂缝的存在和发展通常会使内部的钢筋等材料产生腐蚀，降低钢筋混凝土材料的承载能力、耐久性及抗渗能力，影响建筑物的外观、使用寿命，严重者将会威胁到人们的生命和财产安全。很多工程的失事都是由于裂缝的不稳定发展所致。近代科学研究和大量的混凝土工程实践证明，在混凝土工程中裂缝问题是不可避免的，在一定的范围内也是可以接受的，只是要采取有效的措施将其危害程度控制在一定的范围之内。钢筋混凝土规范也明确规定：有些结构在所处的不同条件下，允许存在一定宽度的裂缝。但在施工中应尽量采取有效措施控制裂缝产生，使结构尽可能不出现裂缝或尽量减少裂缝的数量和宽度，尤其要尽量避免有害裂缝的出现，从而确保工程质量。 混凝土裂缝产生的原因很多，有变形引起的裂缝：如温度变化、收缩、膨胀、不均匀沉陷等原因引起的裂缝；有外载作用引起的裂缝；有养护环境不当和化学作用引起的裂缝等等。在实际工程中要区别对待，根据实际情况解决问题。 混凝土工程中常见裂缝及预防: 1.干缩裂缝及预防 干缩裂缝多出现在混凝土养护结束后的一段时间或是混凝土浇筑完毕后的一周左右。水泥浆中水分的蒸发会产生干缩，且这种收缩是不可逆的。干缩裂缝的产生主要是由于混凝土内外水分蒸发程度不同而导致变形不同的结果：混凝土受外部条件的影响，表面水分损失过快，变形较大，内部湿度变化较小变形较小，较大的表面干缩变形受到混凝土内部约束，产生较大拉应力而产生裂缝。相对湿度越低，水泥浆体干缩越大，干缩裂缝越易产 1原文出处及作者：《加拿大土木工程学报》