MC74LCX04DR2中文资料

MC74LCX04

Low?Voltage CMOS Hex Inverter

With 5 V?Tolerant Inputs

The MC74LCX04 is a high performance hex inverter operating from a 2.3 to 3.6 V supply. High impedance TTL compatible inputs significantly reduce current loading to input drivers while TTL compatible outputs offer improved switching noise performance. A V I specification of 5.5 V allows MC74LCX04 inputs to be safely driven from 5 V devices.

Current drive capability is 24 mA at the outputs.

Features

?Designed for 2.3 V to 3.6 V V CC Operation

?5 V Tolerant Inputs ? Interface Capability With 5 V TTL Logic ?LVTTL Compatible

?LVCMOS Compatible

?24 mA Balanced Output Sink and Source Capability

?Near Zero Static Supply Current (10 m A) Substantially Reduces System Power Requirements

?Latchup Performance Exceeds 500 mA

?ESD Performance:Human Body Model >2000 V;

Machine Model >200 V

?Pb?Free Packages are Available*

*For additional information on our Pb?Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.

A=Assembly Location

L, WL=Wafer Lot

Y=Year

W, WW=Work Week

TSSOP?14

DT SUFFIX

CASE 948G

1

SOEIAJ?14

M SUFFIX

CASE 965

SOIC?14

D SUFFIX

CASE 751A

1

14

LCX

04

ALYW

74LCX04

ALYW

14

1

MARKING

DIAGRAMS

See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet.

ORDERING INFORMATION

https://www.wendangku.net/doc/1b3112991.html,

Figure 1. Pinout: 14?Lead (Top View)

13

14

12

11

10

9

8

2134567V CC A3O3A4O4A5O5A0

O0

A1

O1

A2

O2

GND

O0A0O1A1O2A2O3A3

O4A4O5

A5

Figure 2. Logic Diagram

values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,damage may occur and reliability may be affected.1.I O absolute maximum rating must be observed.

RECOMMENDED OPERATING CONDITIONS

DC ELECTRICAL CHARACTERISTICS

I

AC CHARACTERISTICS t = t = 2.5 ns; R = 500 W

The specification applies to any outputs switching in the same direction, either HIGH?to?LOW (t OSHL) or LOW?to?HIGH (t OSLH); parameter guaranteed by design.

DYNAMIC SWITCHING CHARACTERISTICS

measured in the LOW state.

CAPACITIVE CHARACTERISTICS

ORDERING INFORMATION

?For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.

*This package is inherently Pb?Free.

WAVEFORM 1 ? PROPAGATION DELAYS t R = t F = 2.5 ns, 10% to 90%; f = 1 MHz; t W = 500 ns

V CC

0 V

V OH

V OL

An

On

Figure 3. AC Waveforms

V R L

C L = 50 pF at V CC = 3.3 0.3 V or equivalent (includes jig and probe capacitance)C L = 30 pF at V CC = 2.5 0.2 V or equivalent (includes jig and probe capacitance)R L = R 1 = 500 W or equivalent

R T = Z OUT of pulse generator (typically 50 W )

Figure 4. Test Circuit

PACKAGE DIMENSIONS

SOIC?14D SUFFIX CASE 751A?03ISSUE G

TSSOP?14DT SUFFIX CASE 948G?01

ISSUE O

DIM MIN MAX MIN MAX INCHES

MILLIMETERS A 4.90 5.100.1930.200B 4.30 4.500.1690.177C ??? 1.20???0.047D 0.050.150.0020.006F 0.500.750.0200.030G 0.65 BSC 0.026 BSC H 0.500.600.0200.024J 0.090.200.0040.008J10.090.160.0040.006K 0.190.300.0070.012K10.190.250.0070.010L 6.40 BSC 0.252 BSC M

0 8 0 8 NOTES:

1.DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 198

2.

2.CONTROLLING DIMENSION: MILLIMETER.

3.DIMENSION A DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15(0.006) PER SIDE.

4.DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.

5.DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR

PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION.

6.TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY.

7.DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE ?W?.

__

__

14X REF K

1.DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 198

2.

2.CONTROLLING DIMENSION: MILLIMETER.

3.DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION.

4.MAXIMUM MOLD PROTRUSION 0.15 (0.006)PER SIDE.

5.DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127(0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION.

DIM MIN MAX MIN MAX INCHES

MILLIMETERS A 8.558.750.3370.344B 3.80 4.000.1500.157C 1.35 1.750.0540.068D 0.350.490.0140.019F 0.40 1.250.0160.049G 1.27 BSC 0.050 BSC J 0.190.250.0080.009K 0.100.250.0040.009M 0 7 0 7 P 5.80 6.200.2280.244R

0.250.50

0.0100.019

____

PACKAGE DIMENSIONS

SOEIAJ?14

M SUFFIX

CASE 965?01

ISSUE O

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION