当前位置：文档库 › BTA204S-800E中文资料

BTA204S-800E中文资料

DISCRETE SEMICONDUCTORS DATA SHEET

BTA204S series D, E and F

BTA204M series D, E and F

Three quadrant triacs guaranteed commutation

Product speci?cation December1998

guaranteed commutation

BTA204M series D, E and F

GENERAL DESCRIPTION

QUICK REFERENCE DATA

Passivated guaranteed commutation SYMBOL

PARAMETER

MAX.MAX.

MAX.UNIT triacs in a plastic envelope suitable for surface mounting,intended for use in BTA204S (or BTA204M)-500D 600D -motor control circuits or with other BTA204S (or BTA204M)-500E 600E 800E highly inductive loads.These devices BTA204S (or BTA204M)-500F 600F 800F balance the requirements of V DRM Repetitive peak 500600800V commutation performance and gate off-state voltages sensitivity.The "sensitive gate"E I T(RMS)RMS on-state current 444A series and "logic level"D series are I TSM

Non-repetitive peak on-state 2525

intended for interfacing with low power current

drivers,including micro controllers.

PINNING - SOT428

PIN CONFIGURATION

SYMBOL

PIN Standard Alternative NUMBER S M

1MT1gate 2MT2MT23gate MT1tab

MT2

LIMITING VALUES

Limiting values in accordance with the Absolute Maximum System (IEC 134).SYMBOL PARAMETER

CONDITIONS

MIN.MAX.UNIT -500-600-800V DRM Repetitive peak off-state

-5001

6001800

V voltages

I T(RMS)RMS on-state current full sine wave;-4

T mb ≤ 107 ?C I TSM

Non-repetitive peak full sine wave;on-state current

T j = 25 ?C prior to surge t = 20 ms -25A t = 16.7 ms -27A I 2t I 2t for fusing

t = 10 ms

3.1A 2s dI T /dt Repetitive rate of rise of I TM = 6 A; I G = 0.2 A;100A/μs on-state current after dI G /dt = 0.2 A/μs triggering

I GM Peak gate current -2A V GM Peak gate voltage -5V P GM Peak gate power -5W P G(AV)Average gate power over any 20 ms -0.5W period

T stg Storage temperature -40150?C T j

Operating junction -

125

temperature

tab

T2G

1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may switch to the on-state. The rate of rise of current should not exceed 6 A/μs.

guaranteed commutation

BTA204M series D, E and F

THERMAL RESISTANCES

SYMBOL PARAMETER

CONDITIONS

MIN.TYP.MAX.UNIT R th j-mb Thermal resistance full cycle -- 3.0K/W junction to mounting base half cycle -- 3.7K/W R th j-a

Thermal resistance pcb (FR4) mounted; footprint as in Fig.14-

K/W

junction to ambient

STATIC CHARACTERISTICS

T j = 25 ?C unless otherwise stated SYMBOL PARAMETER CONDITIONS

MIN.

TYP.

MAX.UNIT

BTA204S (or BTA204M)-...D ...E ...F I GT

Gate trigger current 2

V D = 12 V; I T = 0.1 A T2+ G+--51025mA T2+ G---51025mA T2- G---51025mA I L

Latching current

V D = 12 V; I GT = 0.1 A T2+ G+--61220mA T2+ G---91830mA T2- G---61220mA I H Holding current V D = 12 V; I GT = 0.1 A --6

1220

mA V T On-state voltage I T = 5 A

- 1.4 1.7V V GT

Gate trigger voltage

V D = 12 V; I T = 0.1 A -0.7 1.5V V D = 400 V; I T = 0.1 A;0.250.4-V T j = 125 ?C

I D

Off-state leakage V D = V DRM(max); T j = 125 ?C

-0.1

0.5

mA current

DYNAMIC CHARACTERISTICS

T j = 25 ?C unless otherwise stated SYMBOL PARAMETER CONDITIONS

MIN.TYP.

MAX.

UNIT

BTA204S (or BTA204M)-...D

...E ...F dV D /dt Critical rate of rise of V DM = 67% V DRM(max);203050--V/μs off-state voltage

T j = 125 ?C; exponential waveform; gate open circuit

dI com /dt

Critical rate of change V DM = 400 V; T j = 125 ?C; 1.0 2.0

2.5

--A/ms

of commutating current I T(RMS) = 4 A;

dV com /dt = 20V/μs; gate open circuit

dI com /dt

Critical rate of change V DM = 400 V; T j = 125 ?C; 5.0----A/ms

of commutating current I T(RMS) = 4 A;

dV com /dt = 0.1V/μs; gate open circuit

t gt

Gate controlled turn-on I TM = 12 A; V D = V DRM(max);---2-μs

time I G = 0.1 A; dI G /dt = 5 A/μs

2 Device does not trigger in the T2-, G+ quadrant.

guaranteed commutation

BTA204M series D, E and F

Fig.1. Maximum on-state dissipation, P tot , versus rms on-state current, I T(RMS), where α = conduction angle.Fig.2. Maximum permissible non-repetitive peak on-state current I TSM , versus pulse width t p , for

sinusoidal currents, t p ≤ 20ms.Fig.3. Maximum permissible non-repetitive peak on-state current I TSM , versus number of cycles, for

sinusoidal currents, f = 50 Hz.

Fig.4. Maximum permissible rms current I T(RMS) ,

versus mounting base temperature T mb .

Fig.5. Maximum permissible repetitive rms on-state current I T(RMS), versus surge duration, for sinusoidal

currents, f = 50 Hz; T mb ≤ 107?C.

Fig.6. Normalised gate trigger voltage

V GT (T j )/ V GT (25?C), versus junction temperature T j .

012

12345678= 180120906030

BT136

IT(RMS) / A

Ptot / W Tmb(max) / C

125122

119116113110107104

101-50

50100150

BT136

Tmb / C

IT(RMS) / A

107 C

10us

100us

1ms 10ms

100ms

100

1000

BT136

T / s

ITSM / A T

I TSM time

I Tj initial = 25 C max

dI /dt limit T

T2- G+ quadrant

0.01

0.1110

81012BT136

surge duration / s

IT(RMS) / A

101001000

51015202530BT136

Number of cycles at 50Hz

ITSM / A T

I TSM time

I Tj initial = 25 C max

-50

50100150

0.40.6

0.811.21.41.6BT136

Tj / C

VGT(Tj)VGT(25 C)

guaranteed commutation

BTA204M series D, E and F

Fig.7. Normalised gate trigger current I GT (T j )/ I GT (25?C), versus junction temperature T j .

Fig.8. Normalised latching current I L (T j )/ I L (25?C),

versus junction temperature T j .

Fig.9. Normalised holding current I H (T j )/ I H (25?C),

versus junction temperature T j .

Fig.10. Typical and maximum on-state characteristic.

Fig.11. Transient thermal impedance Z th j-mb , versus

pulse width t p .

-50

5010015000.5

11.522.53BTA204

Tj / C

T2+ G+T2+ G-T2- G-

IGT(Tj)IGT(25 C)

00.51

1.52

2.53

24681012

BT136

VT / V

IT / A

Tj = 125 C Tj = 25 C

typ

max

Vo = 1.27 V Rs = 0.091 ohms

-50

50100150

00.5

11.522.53TRIAC

Tj / C

IL(Tj)IL(25 C)

10us

0.1ms 1ms 10ms 0.1s 1s 10s

0.010.1

BT136

tp / s

Zth j-mb (K/W)unidirectional bidirectional

P t

-50

50100150

00.5

11.522.53TRIAC

Tj / C

IH(Tj)IH(25C)

guaranteed commutation

BTA204M series D, E and F

MECHANICAL DATA

Dimensions in mm Net Mass: 1.1 g

Fig.12. SOT428 : centre pin connected to tab.

MOUNTING INSTRUCTIONS

Dimensions in mm

Fig.13. SOT428 : minimum pad sizes for surface mounting .

Notes

1. Plastic meets UL94 V0 at 1/8".

6.22 max

2.38 max 0.93 max

6.73 max

0.310.4 max

0.5

0.8 max (x2)

2.285 (x2)

0.5

seating plane

1.1

0.5 min

5.4

4 min

4.6

tab

7.0

2.152.5

4.57

1.5

guaranteed commutation BTA204M series D, E and F

DEFINITIONS

Data sheet status

Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications.

Limiting values

Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information

Where application information is given, it is advisory and does not form part of the specification.

? Philips Electronics N.V. 1998

All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.

The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.

? Philips Electronics N.V.SCA All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.

The information presented in this document does not form part of any quotation or contract,is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.

Internet: https://www.wendangku.net/doc/165775347.html,

1999

Philips Semiconductors – a worldwide company

For all other countries apply to: Philips Semiconductors,

International Marketing &Sales Communications, Building BE-p, P.O.Box 218,5600MD EINDHOVEN, The Netherlands,Fax.+31402724825Argentina: see South America

Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140,Tel.+61297048141,Fax.+61297048139

Austria:Computerstr. 6, A-1101 WIEN, P.O. Box 213,Tel.+431601011248, Fax.+431601011210

Belarus: Hotel Minsk Business Center, Bld.3, r.1211, Volodarski Str.6,220050MINSK, Tel.+375172200733,Fax.+375172200773Belgium: see The Netherlands Brazil:see South America

Bulgaria:Philips Bulgaria Ltd., Energoproject, 15th floor,51James Bourchier Blvd., 1407SOFIA,Tel.+3592689211,Fax.+3592689102

Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,Tel.+18002347381, Fax.+18009430087

China/Hong Kong: 501Hong Kong Industrial Technology Centre,72Tat Chee Avenue, Kowloon Tong, HONG KONG,Tel.+852********,Fax.+852********Colombia: see South America Czech Republic: see Austria

Denmark: Sydhavnsgade 23, 1780COPENHAGEN V,Tel.+4533293333,Fax.+4533293905Finland: Sinikalliontie 3, FIN-02630ESPOO,Tel.+3589615800,Fax.+358961580920

France: 51Rue Carnot, BP317, 92156SURESNES Cedex,Tel.+33140996161,Fax.+33140996427

Germany: Hammerbrookstra?e 69, D-20097HAMBURG,Tel.+4940235360,Fax.+494023536300Hungary:see Austria

India: Philips INDIA Ltd, Band Box Building, 2nd floor,254-D,Dr.Annie Besant Road, Worli, MUMBAI 400025,Tel.+91224938541,Fax.+91224930966

Indonesia:PT Philips Development Corporation,Semiconductors Division,Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510,Tel.+62217940040ext.2501, Fax.+62217940080

Ireland: Newstead, Clonskeagh, DUBLIN 14,Tel.+35317640000,Fax.+35317640200

Israel: RAPAC Electronics, 7Kehilat Saloniki St, PO Box 18053,TEL AVIV 61180, Tel.+97236450444,Fax.+97236491007

Italy:PHILIPS SEMICONDUCTORS,Via Casati,23-20052MONZA (MI),Tel. +390392036838,Fax +390392036800

Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku,

TOKYO 108-8507, Tel.+81337405130,Fax.+81337405057Korea: Philips House, 260-199Itaewon-dong, Yongsan-ku, SEOUL,Tel.+8227091412,Fax.+8227091415

Malaysia: No.76Jalan Universiti, 46200PETALING JAYA, SELANGOR,Tel.+60 37505214,Fax.+6037574880

Mexico: 5900Gateway East, Suite 200, EL PASO, TEXAS 79905,Tel.+9-58002347381, Fax +9-58009430087Middle East: see Italy

Netherlands: Postbus 90050, 5600PB EINDHOVEN, Bldg.VB,Tel.+31402782785,Fax.+31402788399

New Zealand: 2Wagener Place, C.P.O.Box 1041, AUCKLAND,Tel.+6498494160,Fax.+6498497811Norway: Box 1, Manglerud 0612, OSLO,Tel.+4722748000,Fax.+4722748341Pakistan: see Singapore

Philippines: Philips Semiconductors Philippines Inc.,

106Valero St.Salcedo Village, P.O.Box 2108MCC,MAKATI,Metro MANILA, Tel.+6328166380,Fax.+6328173474Poland : Al.Jerozolimskie 195B,02-222WARSAW,Tel.+48225710000,Fax.+48225710001Portugal: see Spain Romania: see Italy

Russia: Philips Russia, https://www.wendangku.net/doc/165775347.html,atcheva 35A, 119048MOSCOW,Tel.+70957556918,Fax.+70957556919

Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762,Tel.+653502538,Fax.+652516500Slovakia: see Austria Slovenia: see Italy

South Africa: S.A. PHILIPS Pty Ltd., 195-215Main Road Martindale,2092JOHANNESBURG, P.O.Box 58088 Newville 2114,Tel.+27114715401,Fax.+27114715398

South America: Al.Vicente Pinzon,173, 6th floor,04547-130S?O PAULO,SP, Brazil,

Tel.+55118212333,Fax.+55118212382Spain: Balmes 22, 08007BARCELONA,Tel.+34933016312,Fax.+34933014107

Sweden: Kottbygatan 7, Akalla, S-16485STOCKHOLM,Tel.+46859852000,Fax.+46859852745

Switzerland: Allmendstrasse 140, CH-8027ZüRICH,Tel.+4114882741Fax.+4114883263

Taiwan: Philips Semiconductors, 6F, No.96, Chien Kuo N.Rd.,Sec.1,TAIPEI, Taiwan Tel.+886221342886,Fax.+886221342874Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,

209/2Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,Tel.+6627454090,Fax.+6623980793

Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260Umraniye,ISTANBUL, Tel.+902165221500,Fax.+902165221813

Ukraine : PHILIPS UKRAINE, 4Patrice Lumumba str., Building B, Floor 7,252042KIEV, Tel.+380442642776, Fax. +380442680461

United Kingdom: Philips Semiconductors Ltd., 276Bath Road, Hayes,MIDDLESEX UB35BX, Tel.+442087305000,Fax.+442087548421United States: 811East Arques Avenue, SUNNYVALE, CA 94088-3409,Tel.+18002347381, Fax.+18009430087Uruguay: see South America

Vietnam: see Singapore

Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000BEOGRAD,Tel.+38111625344,Fax.+38111635777

Printed in The Netherlands

135002/1160/03/pp 8 Date of release:December 1998

Document order number: 939775006619