Release_Note_InstallSheild_Project
****************************************************************************
**************** D720200 & D720200A Design Resources Release ***************
****************************************************************************
Release Note April.22.2011
Renesas Electronics uPD720200 & uPD720200A
USB 3.0 Host Controller Driver Installer Project
Kit Version : 2.1.16.0 : April 22th, 2011
Copyright (C) Renesas Electronics Corporation 2010-2011 All Rights Reserved
****************************************************************************
NOTE1:
This installer package is generated with the InstallShield2010 SP1 Premier.
If the previous driver package(v0.X.X.X , v1.0.1.0 or v1.0.7.0) is installed,
Please uninstall the previous driver package and install new package.
---------------------------------------------------------------------------
Table of Contents
---------------------------------------------------------------------------
1. Release Files
2. Command Line Options
3. History
---------------------------------------------------------------------------
---------------------------------------------------------------------------
1. Release Files
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Date Time Size File Name Version
2011/04/19 19:03 3052KB usb3drvinst-msi_USB3-Host-21160.ism 2.1.16.0
--CustomDLL
---x64
2011/01/21 15:20 98KB nusb3drvinst.dll 1.2.3.0
---x86
2011/01/21 15:19 92KB nusb3drvinst.dll 1.2.3.0
--LicenseAgreement
2010/04/02 14:56 32KB License.rtf 1.1d
--Script Files
2010/05/13 13:21 3KB Setup.Rul
--VersionDLL
2011/04/31 08:56 48KB nusb3ver.dll 2.0.34.1
---------------------------------------------------------------------------
---------------------------------------------------------------------------
2. Command Line Options
---------------------------------------------------------------------------
---------------------------------------------------------------------------
1)Silent install
Ex.) setup.exe /s
-To install this driver package silently, "setup.iss" file is needed.
This package includes the "setup.iss" in which the following folder
path is set.
"C:\Program Files\Renesas Electronics\USB 3.0 Host Controller Driver".
If you want to change install path, you need to generate setup.iss as
follows: setup /r /f1".\setup.iss"
2)Check existence of USB3.0 Host Controller
Ex.) setup.exe /v"CHECK_HW_EXIST=1"
-When this command line option is set, the installer checks existence of
the USB3.0 Host Controller(uPD720200). If the uPD720200 is not in the PC,
this installer does not install the device drivers.
##Caution##
To in
stall the device drivers with this command line option after
uninstalling the device drivers, it is necessary to restart the PC.
3) Not install the USB3.0 Monitor application (nusb3mon.exe/dll)
/v"NO_MONITOR=1"
-When this command line option is set, the USB3.0 Monitor Application
(nusb3mon.exe/dll) is not installed.
##Caution##
If the USB3.0 Monitor Application is already installed, it is necessary to
uninstall the USB3 driver package of previous version before installing the
new USB3 driver package (v1.0.19.0 or later).
4) Not install the USB3.0 Utility application (nusb3utl.exe)
/v"NO_UTILITY=1"
-When this command line option is set, the USB3.0 Utility Application
(nusb3utl.exe) is not installed.
##Caution##
If the USB3.0 Utility Application is already installed, it is necessary to
uninstall the USB3 driver package of previous version before installing the
new USB3 driver package (v2.0.4.0 or later).
5) Disable the Selective Suspend function
Ex.) setup.exe /v"SET_SELSUS_MODE1=1"
-Selective Suspend function is enabled by default starting with Ver2.0.20.0.
This option disables the Selective Suspend function. The Selective Suspend
function is described in section 1.4 & 2.8 of "USB 3.0 Host Controller Driver
Application Note (ISG-NC1-200030)". Please see that document for more detail.
##Note##
This option is supported from Ver.2.0.20.0.
The Selective Suspend function for External Hubs is supported from Ver.2.0.20.0.
6) Hide the pop-up message
Ex.) setup.exe /v"CHECK_HW_EXIST=1 NO_MESSAGE=1"
-This option suppresses the pop-up message when it is used with the "CHECK_HW_EXIST"
option. If you want to hide the pop-up message on the "CHECK_HW_EXIST" option,
you should use this option on the command line.
-This option is described in section 2.5 & 2.9 of "USB 3.0 Host Controller Driver
Application Note(ISG-NC1-200030)". Please see that document for more detail.
##Note##
This option is supported from Ver.2.0.20.0.
This option must be used only with the "CHECK_HW_EXIST" option. If this option is used
by itself, it has no effect.
7) Disable the Dynamic U1/U2 state control function
Ex.) setup.exe /v"U1U2_DISABLE=1"
-The Dynamic U1/U2 state control function is enabled by default starting with
Ver2.0.4.0. If you want to disable the Dynamic U1/U2 state control function,
you should use this option on the command prompt.
##Note##
This option is supported from Ver.2.0.26.0.
8) Disable the check box to disable the Dynamic U1/U2 state control function
on "nusb3utl.exe"
Ex.) setup.exe /v"U1U2_UTL_DISABLE=1"
-From ver2.0.26.0, the USB 3.0 Host controller Utility supported the check-box
to disable the Dynamic U1/U2 state control function. This check-box is appeared
in default setting.
If you don't want to display this checkbox on USB3.0 Host controller Utility,
you should u
se this option on the command prompt.
##Note##
This option is supported from Ver.2.0.26.0.
##NEW##
9) Display the Custom Property page on the device manager
Ex.) setup.exe /v"DP_PROPERTY=1"
-From ver2.1.16.0, the USB 3.0 Host controller Driver supported the Custom
Property page to display the firmware version and disable the Dynamic U1/U2
state control function.
##Note##
The Custom Property page is not displayed in default setting with Ver2.1.16.0.
---------------------------------------------------------------------------
---------------------------------------------------------------------------
3. History
---------------------------------------------------------------------------
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Version 2.1.16.0 : April 22th, 2011
---------------------------------------------------------------------------
- Supported the following command line options
Display the Custom Property page on the device manager
Please see "USB 3.0 Host Controller Driver Application Note(ISG-NK1-100001)"
in more detail.
- Update the project file(.ism).
Added the "DP_PROPERTY" option.
Updated the Custom Sction DLL(nusb3drvinst.dll).
Added the files of Custom Property Sheet page.
---------------------------------------------------------------------------
Version 2.0.34.1 : March 31th, 2011
---------------------------------------------------------------------------
- Update the project file(.ism) only.
Change the value of "USB3PMDisable" script of custom action.
---------------------------------------------------------------------------
Version 2.0.34.0 : February 18th, 2011
---------------------------------------------------------------------------
- Update the project file(.ism) only.
---------------------------------------------------------------------------
Version 2.0.32.0 : December 17th, 2010
---------------------------------------------------------------------------
- Update the project file(.ism) only.
---------------------------------------------------------------------------
Version 2.0.30.0 : November 26th, 2010
---------------------------------------------------------------------------
- The following issue was fixed.
1. When the following commandline was run without USB 3.0 Host controller,
the pop-up message was not shown to the foreground.(Modified the custom DLL)
setup.exe /v"CHECK_HW_EXIST=1"
2. There is an unknown character existed in folder's description of the
start menu.(Modified the InstallShield's project file)
---------------------------------------------------------------------------
Version 2.0.26.0 : October 7th, 2010
---------------------------------------------------------------------------
- Supported the following command line options
1. Disable the Dyn
amic U1/U2 state control function.
2. Make checkbox of Dynamic U1/U2 state control function inivisible.
Please see "USB 3.0 Host Controller Driver Application Note(ISG-NC1-200040)"
in more detail.
---------------------------------------------------------------------------
Version 2.0.20.0 : August 13th, 2010
---------------------------------------------------------------------------
- Supported the following command line options
1. Disable the Selective Suspend function.
2. Hide the pop-up message.
Please see "USB 3.0 Host Controller Driver Application Note(ISG-NC1-200030)"
in more detail.
---------------------------------------------------------------------------
Version 2.0.4.0 : May 14th, 2010
---------------------------------------------------------------------------
- Changed the company name from NEC Electronics to Renesas Electronics.
- Changed the Install Dialog Sequence.
- Deleted the Maintenace Dialog.
- Deleted the "Change" option on the Program and Features of Control panel.
- Supported the command Line option(NO_UTILITY) for not installing
the USB3.0 Utility application.