Gamma Compatible Materials List

Gamma Compatible Materials Reference Guide

Gamma Compatible Materials

2Radiation Stability of Selected Medical Grade Polymers

Material Tolerance Level (kGy) Comments

THERMOPLASTICS

Acrylonitrile/Butadiene/Styrene 1,000 Protected by Benzene ring structure.

(ABS) Avoid high dose on high impact grades.

Aromatic Polyesters 1,000 Very stable, retains excellent clarity. Drying is essential.

(PET, PETG) Good in luer connectors.

Cellulosics

Esters and Ethers 100

Paper, Card, Corrugated, Fibers 100-200 Paper and natural fibers scission, discolor and embrittle.

Cellulose Acetate Propiconate and 100 Retains good clarity and impact.

Butyrate

Fluoropolymers

Tetrafluroethylene (PTFE) 5 Liberates fluorine gas, disintegrates to powder. Avoid use.

Polychlorotrifluoroethylene (ECTFE) 200

Polyvinyl Fluoride 1,000

Polyvinylidene Fluoride (PVDF) 1,000

Ethylene-Tetrafluoroethylene (ETFE) 1,000

Fluorinated Ethylene Propylene (FEP) 50 Avoid use.

Polyacetals (Delrin, Celcon) 5 Avoid use due to embrittlement.

Polyacrylics

Polymethylmethacrylate 100 Yellows at 20-40 kGy; clarity recovers partially on aging.

Polyacrylonitrile 100 Yellows at 20-40 kGy.

Polyacrylate 100 Yellows at 20-40 kGy.

Polycyanoacrylate 200 Adhesives function at 100 kGy with less than 30% degradation.

Polyamides (Nylons)

Aliphatic & Amorphous Grades 50 Discolours. Avoid thin films and fibers. Dry before molding.

Aromatic Polyamide/Polyimide 10,000 High heat/strength grade.

Polycarbonate 1,000 Discolours, clarity recovers after aging. Dry before molding.

Polyethylene (LDPE, LLDPE, 1,000 Crosslinks to gain strength, loses some elongation.

HDPE, UHMPE, UHMWPE) All polyethylene radiation stable, low density most resistant.

Polyimides 10,000

Polymethylpentene 20 Subject to oxidation degradation. Avoid use.

Polyphenylene Sulfide 1,000

Polypropylene, Radiation Stabilized

Homopolymer 20-50 Subject to orientation embrittlement. Validate with real time aging.

Copolymers of Propylene-Ethylene 25-60 More stable than Homopolymer.

Polypropylene, natural 20 Avoid use of unstabilized polypropylene.

Note: Physical properties of polymers that are irradiated may vary due to: section thickness; molecular weight distribution; morphology; moisture; oxygen levels; and either residual

or functional stress. Each polymer must be tested in the specific application under consideration.

Gamma Compatible Materials Reference Guide

3 Material Tolerance Level (kGy) Comments

Polystyrene 10,000 All styrenes are stabilized by Benzene ring structure.

Polysulfone 10,000 Amber colour before irradiation.

Polyurethane 10,000 Excellent clarity and chemical resistance to stress-cracking.

Drying is essential.

Polyvinylbutyral 100 Yellows.

Polyvinylchloride (PVC) 100 Yellows, can be tinted for colour correction.

Polyvinylidene Chloride (PVDC) 100 Yellows, releases HCL.

Styrene/Acrylonitrile (SAN) 1,000 Yellows at 40 kGy.

THERMOSETS

Allyl Digylcol Carbonate (Polyester) 5,000-10,000 All thermosets as a class are highly resistant.

Epoxies 1,000 Many good formulations available. Success depends

on joint design and application process.

Phenolics 50,000

Polyesters 100,000

Polyurethanes 100-1,000 Wide formulation variations for urethanes.

ELASTOMERS*

Butyl 50

Ethylene-Propylene Diene Monomer 100-200 Crosslinks, yellows slightly.

(EPDM)

Fluoro Elastomer 50 Avoid multiple sterilization.

Natural Rubber (Isoprene) 100 Very stable with sulfur or resin cure systems.

Nitrile 200 Avoid multiple sterilization.

Polyacrylic 50-200 Avoid multiple sterilization.

Polychloroprene (Neoprene) 200 Avoid multiple sterilization.

Silicones 50-100 Crosslink density increases more in peroxide systems

(Peroxide & Platinum Catalyst Systems) than in platinum systems.

Styrene-Butadiene 100 Avoid multiple sterilization.

Urethanes 100-200 Wide variations in urethane chemistry applied to medical devices.

* E lastomers: 1) Radiation tolerance is affected by the base polymer and the curing system used. Sulfur and resin cures are more durable.

2) All elastomers are subject to cross-linking. Avoid folds, coils, curves in the shape packaged. T ypical sterilization processing dose: 20-50 kGy (2.0-5.0 Mrads).

Although MDS Nordion compiles this information, we do not verify radiation compatibility of the products listed.

It is recommended that all materials should be tested thoroughly to verify the compounds’ performance after irradiation.

An excellent reference source is the Association for the Advancement of Medical Instrumentation web site at https://www.wendangku.net/doc/1115024317.html,

for a material qualification technical information report and sterilization standard.

https://www.wendangku.net/doc/1115024317.html,

Corporate Headquarters: 447 March Road

Ottawa, ON, Canada K2K 1X8 Tel: +1 613 592 2790

Fax: +1 613 592 6937Regional Office:

4004 Wesbrook Mall

Vancouver, BC, Canada V6T 2A3

Tel: +1 604 228 8952

Fax: +1 604 228 5990

European Office:

Zoning Industriel

Avenue de l’Espérance

B-6220 Fleurus, Belgium

Tel: +32 71 82 35 86

Fax: +32 71 82 36 66

Asia Pacific Sales Offices:

Hong Kong

901 Matheson Centre

3 Matheson Street

Causeway Bay, Hong Kong

Tel: +852 2827 8666

Fax: +852 2827 8302

Japan

Room 905, Tokyo Royal Plaza

1-18-11, Uchi-kanda, Chiyoda-ku

Tokyo 101-0047, Japan

Tel: +81 3 5283 6872

Fax: +81 3 5283 6873