土木工程中英文对照外文翻译文献
中英文翻译
1 中文翻译
1.1钢筋混凝土
素混凝土是由水泥、水、细骨料、粗骨料（碎石或；卵石）、空气，通常还有其他外加剂等经过凝固硬化而成。将可塑的混凝土拌合物注入到模板内，并将其捣实，然后进行养护，以加速水泥与水的水化反应，最后获得硬化的混凝土。其最终制成品具有较高的抗压强度和较低的抗拉强度。其抗拉强度约为抗压强度的十分之一。因此，截面的受拉区必须配置抗拉钢筋和抗剪钢筋以增加钢筋混凝土构件中较弱的受拉区的强度。
由于钢筋混凝土截面在均质性上与标准的木材或钢的截面存在着差异，因此，需要对结构设计的基本原理进行修改。将钢筋混凝土这种非均质截面的两种组成部分按一定比例适当布置，可以最好的利用这两种材料。这一要求是可以达到的。因混凝土由配料搅拌成湿拌合物，经过振捣并凝固硬化，可以做成任何一种需要的形状。如果拌制混凝土的各种材料配合比恰当，则混凝土制成品的强度较高，经久耐用，配置钢筋后，可以作为任何结构体系的主要构件。
浇筑混凝土所需要的技术取决于即将浇筑的构件类型，诸如：柱、梁、墙、板、基础，大体积混凝土水坝或者继续延长已浇筑完毕并且已经凝固的混凝土等。对于梁、柱、墙等构件，当模板清理干净后应该在其上涂油，钢筋表面的锈及其他有害物质也应该被清除干净。浇筑基础前，应将坑底土夯实并用水浸湿6英寸，以免土壤从新浇的混凝土中吸收水分。一般情况下，除使用混凝土泵浇筑外，混凝土都应在水平方向分层浇筑，并使用插入式或表面式高频电动振捣器捣实。必须记住，过分的振捣将导致骨料离析和混凝土泌浆等现象，因而是有害的。
水泥的水化作用发生在有水分存在，而且气温在50°F以上的条件下。为了保证水泥的水化作用得以进行，必须具备上述条件。如果干燥过快则会出现表面裂缝，这将有损与混凝土的强度，同时也会影响到水泥水化作用的充分进行。
设计钢筋混凝土构件时显然需要处理大量的参数，诸如宽度、高度等几何尺寸，配筋的面积，钢筋的应变和混凝土的应变，钢筋的应力等等。因此，在选择混凝土截面时需要进行试算并作调整，根据施工现场条件、混凝土原材料的供应情况、业主提出的特殊要求、对建筑和净空高度的要求、所用的设计规范以及建筑物周围环境条件等最后确定截面。钢筋混凝土通常是现场浇注的合成材料，它与在工厂中制造的标准的钢结构梁、柱等不同，因此对于上面所提到的一系列因素必须予以考虑。
对结构体系的各个部位均需选定试算截面并进行验算，以确定该截面的名义强
度是否足以承受所作用的计算荷载。由于经常需要进行多次试算，才能求出所需的截面，因此设计时第一次采用的数值将导致一系列的试算与调整工作。
选择混凝土截面时，采用试算与调整过程可以使复核与设计结合在一起。因此，当试算截面选定后，每次设计都是对截面进行复核。手册、图表和微型计算机以及专用程序的使用，使这种设计方法更为简捷有效，而传统的方法则是把钢筋混凝土的复核与单纯的设计分别进行处理。
1.2土方工程
由于和土木工程中任何其他工种的施工方法与费用相比较，土方挖运的施工方法与费用的变化都要快得多，因此对于有事业心的人来说，土方工程是一个可以大有作为的领域。在1935年，目前采用的利用轮胎式机械设备进行土方挖运的方法大多数还没有出现。那是大部分土方是采用窄轨铁路运输，在这目前来说是很少采用的。当时主要的开挖方式是使用正铲、反铲、拉铲或抓斗等挖土机，尽管这些机械目前仍然在广泛应用，但是它们只不过是目前所采用的许多方法中的一小部分。因此，一个工程师为了使自己在土方挖运设备方面的知识跟得上时代的发展，他应当花费一些时间去研究现代的机械。一般说来，有关挖土机、装载机和运输机械的唯一可靠而又最新的资料可以从制造厂商处获得。
土方工程或土方挖运工程指的是把地表面过高处的土壤挖去（挖方），并把它倾卸到地表面过低的其他地方（填方）。为了降低土方工程费用，填方量应该等于挖方量，而且挖方地点应该尽可能靠近土方量相等的填方地点，以减少运输量和填方的二次搬运。土方设计这项工作落到了从事道路设计的工程师的身上，因为土方工程的设计比其他任何工作更能决定工程造价是否低廉。根据现有的地图和标高，道路工程师应在设计绘图室中的工作也并不是徒劳的。它将帮助他在最短的时间内获得最好的方案。
费用最低的运土方法是用同一台机械直接挖方取土并且卸土作为填方。这并不是经常可以做到的，但是如果能够做到则是很理想的，因为这样做既快捷又省钱。拉铲挖土机。推土机和正铲挖土机都能做到这点。拉铲挖土机的工作半径最大。推土机所推运的图的数量最多，只是运输距离很短。拉铲挖土机的缺点是只能挖比它本身低的土，不能施加压力挖入压实的土壤内，不能在陡坡上挖土，而且挖。卸都不准确。
正铲挖土机介于推土机和拉铲挖土机的之间，其作用半径大于推土机，但小于拉铲挖土机。正铲挖土机能挖取竖直陡峭的工作面，这种方式对推土机司机来说是危险的，而对拉铲挖土机则是不可能的。每种机械设备应该进行最适合它的性能的作业。正铲挖土机不能挖比其停机平面低很多的土，而深挖坚实的土壤时，反铲挖
土机最适用，但其卸料半径比起装有正铲的同一挖土机的卸料半径则要小很多。
在比较平坦的场地开挖，如果用拉铲或正铲挖土机运输距离太远时，则装有轮胎式的斗式铲运机就是比不可少的。它能在比较平的地面上挖较深的土（但只能挖机械本身下面的土），需要时可以将土运至几百米远，然后卸土并在卸土的过程中把土大致铲平。在挖掘硬土时，人们发现在开挖场地经常用一辆助推拖拉机（轮式或履带式），对返回挖土的铲运机进行助推这种施工方法是经济的。一旦铲运机装满，助推拖拉机就回到开挖的地点去帮助下一台铲运机。
斗式铲运机通常是功率非常大的机械，许多厂家制造的铲运机铲斗容量为8 m 3，满载时可达10 m3。最大的自行式铲运机铲斗容量为19立方米（满载时为25 m 3），由430马力的牵引发动机驱动。
翻斗机可能是使用最为普遍的轮胎式运输设备，因为它们还可以被用来送混凝土或者其他建筑材料。翻斗车的车斗位于大橡胶轮胎车轮前轴的上方，尽管铰接式翻斗车的卸料方向有很多种，但大多数车斗是向前翻转的。最小的翻斗车的容量大约为0.5立方米，而最大的标准型翻斗车的容量大约为4.5m3。特殊型式的翻斗车包括容量为4 m3的自装式翻斗车，和容量约为0.5 m3的铰接式翻斗车。必须记住翻斗车与自卸卡车之间的区别。翻斗车车斗向前倾翻而司机坐在后方卸载，因此有时被称为后卸卡车。
1.3结构的安全度
规范的主要目的是提供一般性的设计原理和计算方法，以便验算结构的安全度。就目前的趋势而言，安全系数与所使用的材料性质及其组织情况无关，通常把它定义为发生破坏的条件与结构可预料的最不利的工作条件之比值。这个比值还与结构的破坏概率（危险率）成反比。
破坏不仅仅指结构的整体破坏，而且还指结构不能正常的使用，或者，用更为确切的话来说，把破坏看成是结构已经达到不能继续承担其设计荷载的“极限状态”。通常有两种类型的极限状态，即：
（1）强度极限状态，它相当于结构能够达到的最大承载能力。其例子包括结构的局部屈曲和整体不稳定性；某此界面失效，随后结构转变为机构；疲劳破坏；引起结构几何形状显著变化的弹性变形或塑性变形或徐变；结构对交变荷载、火灾和爆炸的敏感性。
（2）使用极限状态，它对应着结构的使用功能和耐久性。器例子包括结构失稳之前的过大变形和位移；早期开裂或过大的裂缝；较大的振动和腐蚀。
根据不同的安全度条件，可以把结构验算所采用的计算方法分成：
（1）确定性的方法，在这种方法中，把主要参数看作非随机参数。
（2）概率方法，在这种方法中，主要参数被认为是随机参数。
此外，根据安全系数的不同用途，可以把结构的计算方法分为：
（1）容许应力法，在这种方法中，把结构承受最大荷载时计算得到的应力与经过按规定的安全系数进行折减后的材料强度作比较。
（2）极限状态法，在这种方法中，结构的工作状态是以其最大强度为依据来衡量的。由理论分析确定的这一最大强度应不小于结构承受计算荷载所算得的强度（极限状态）。计算荷载等于分别乘以荷载系数的活载与恒载之和。
把对应于不乘以荷载系数的活载和恒载的工作（使用）条件的应力与规定值（使用极限状态）相比较。根据前两种方法和后两种方法的四种可能组合，我们可以得到一些实用的计算方法。通常采用下面两种计算方法：
确定性的方法，这种方法采用容许应力。
概率方法，这种方法采用极限状态。
至少在理论上，概率法的主要优点是可以科学的考虑所有随机安全系数，然后将这些随机安全系数组合成确定的安全系数。概率法取决于：
（1）制作和安装过程中材料强度的随机分布（整个结构的力学性能数值的分散性）；
（2）截面和结构几何尺寸的不确定性（由结构制作和安装造成的误差和缺陷而引起的）；
对作用在结构上的活载和恒载的预测的不确定性；
所采用的近似计算方法有关的不精确性（实际应力与计算应力的偏差）。
此外，概率理论意味着可以基于下面几个因素来确定允许的危险率，例如：建筑物的重要性和建筑物破坏造成的危害性；
（2）由于建筑物破坏使生活受到威胁的人数；
（3）修复建筑的可能性；
（4）建筑物的预期寿命。
所有这些因素均与经济和社会条件有关，例如：
（1）建筑物的初始建设费；
（2）建筑物使用期限内的折旧费；
（3）由于建筑物破坏而造成的物质和材料损失费；
（4）在社会上造成的不良影响；
（5）精神和心理上的考虑。
就给定的安全系数而论，所有这些参数的确定都是以建筑物的最佳成本为依据的。但是，应该考虑到进行全概率分析的困难。对于这种分析来说，应该了解活载及其所引起的盈利的分布规律、材料的力学性能的分散性和截面的结构几何尺寸的
分散性。此外，由于强度的分布规律和应力的分布规律之间的相互关系是困难的。这些实际困难可以采用两种方法来克服。第一种方法对材料和荷载采用不同的安全系数，而不需要采用概率准则；第二种方法是引入一些而简化假设的近似概率方法（半概率方法）。
2 外文翻译
2.1 Reinforced Concrete
Plain concrete is formed from a hardened mixture of cement ,water ,fine aggregate, coarse aggregate (crushed stone or gravel),air, and often other admixtures. The plastic mix is placed and consolidated in the formwork, then cured to facilitate the acceleration of the chemical hydration reaction lf the cement/water mix, resulting in hardened concrete. The finished product has high compressive strength, and low resistance to tension, such that its tensile strength is approximately one tenth lf its compressive strength. Consequently, tensile and shear reinforcement in the tensile regions of sections has to be provided to compensate for the weak tension regions in the reinforced concrete element.
It is this deviation in the composition of a reinforces concrete section from the homogeneity of standard wood or steel sections that requires a modified approach to the basic principles of structural design. The two components of the heterogeneous reinforced concrete section are to be so arranged and proportioned that optimal use is made of the materials involved. This is possible because concrete can easily be given any desired shape by placing and compacting the wet mixture of the constituent ingredients are properly proportioned, the finished product becomes strong, durable, and, in combination with the reinforcing bars, adaptable for use as main members of any structural system.
The techniques necessary for placing concrete depend on the type of member to be cast: that is, whether it is a column, a bean, a wall, a slab, a foundation. a mass columns, or an extension of previously placed and hardened concrete. For beams, columns, and walls, the forms should be well oiled after cleaning them, and the reinforcement should be cleared of rust and other harmful materials. In foundations, the earth should be compacted and thoroughly moistened to about 6 in. in depth to avoid absorption of the moisture present in the wet concrete. Concrete should always be placed in horizontal layers which are compacted by means of high frequency power-driven vibrators of either the immersion or external type, as the case requires, unless it is placed by pumping. It must be kept in mind, however, that over vibration can be harmful since it could cause segregation of the aggregate and bleeding of the concrete.
Hydration of the cement takes place in the presence of moisture at temperatures above 50°F. It is necessary to maintain such a condition in order that the chemical hydration reaction can take place. If drying is too rapid, surface cracking takes place. This would result in reduction of concrete strength due to cracking as well as the failure to attain full chemical hydration.
It is clear that a large number of parameters have to be dealt with in proportioning a reinforced concrete element, such as geometrical width, depth, area of reinforcement, steel strain, concrete strain, steel stress, and so on. Consequently, trial and adjustment is necessary in the choice of concrete sections, with assumptions based on conditions at site, availability of the constituent materials, particular demands of the owners, architectural and headroom requirements, the applicable codes, and environmental reinforced concrete is often a site-constructed composite, in contrast to the standard mill-fabricated beam and column sections in steel structures.
A trial section has to be chosen for each critical location in a structural system. The trial section has to be analyzed to determine if its nominal resisting strength is adequate to carry the applied factored load. Since more than one trial is often necessary to arrive at the required section, the first design input step generates into a series of trial-and-adjustment analyses.
The trial-and –adjustment procedures for the choice of a concrete section lead to the convergence of analysis and design. Hence every design is an analysis once a trial section is chosen. The availability of handbooks, charts, and personal computers and programs supports this approach as a more efficient, compact, and speedy instructional method compared with the traditional approach of treating the analysis of reinforced concrete separately from pure design.
2.2 Earthwork
Because earthmoving methods and costs change more quickly than those in any other branch of civil engineering, this is a field where there are real opportunities for the enthusiast. In 1935 most of the methods now in use for carrying and excavating earth with rubber-tyred equipment did not exist. Most earth was moved by narrow rail track, now relatively rare, and the main methods of excavation, with face shovel, backacter, or dragline or grab, though they are still widely used are only a few of the many current methods. To keep his knowledge of earthmoving equipment up to date an engineer must therefore spend tine studying modern machines. Generally the only reliable up-to-date
information on excavators, loaders and transport is obtainable from the makers.
Earthworks or earthmoving means cutting into ground where its surface is too high ( cuts ), and dumping the earth in other places where the surface is too low ( fills). Toreduce earthwork costs, the volume of the fills should be equal to the volume of the cuts and wherever possible the cuts should be placednear to fills of equal volume so as to reduce transport and double handlingof the fill. This work of earthwork design falls on the engineer who lays out the road since it is the layout of the earthwork more than anything else which decides its cheapness. From the available maps ahd levels, the engineering must try to reach as many decisions as possible in the drawing office by drawing cross sections of the earthwork. On the site when further information becomes available he can make changes in jis sections and layout,but the drawing lffice work will not have been lost. It will have helped him to reach the best solution in the shortest time.
The cheapest way of moving earth is to take it directly out of the cut and drop it as fill with the same machine. This is not always possible, but when it canbe done it is ideal, being both quick and cheap. Draglines, bulldozers and face shovels an do this. The largest radius is obtained with the dragline,and the largest tonnage of earth is moved by the bulldozer, though only over short distances.The disadvantages of the dragline are that it must dig below itself, it cannot dig with force into compacted material, it cannot dig on steep slopws, and its dumping and digging are not accurate.
Face shovels are between bulldozers and draglines, having a larger radius of action than bulldozers but less than draglines. They are anle to dig into a vertical cliff face in a way which would be dangerous tor a bulldozer operator and impossible for a dragline. Each piece of equipment should be level of their tracks and for deep digs in compact material a backacter is most useful, but its dumping radius is considerably less than that of the same escavator fitted with a face shovel.
Rubber-tyred bowl scrapers are indispensable for fairly level digging where the distance of transport is too much tor a dragline or face shovel. They can dig the material deeply ( but only below themselves ) to a fairly flat surface, carry it hundreds of meters if need be, then drop it and level it roughly during the dumping. For hard digging it is often found economical to keep a pusher tractor ( wheeled or tracked ) on the digging site, to push each scraper as it returns to dig. As soon as the scraper is full,the pusher tractor returns to the beginning of the dig to heop to help the nest scraper.
Bowl scrapers are often extremely powerful machines;many makers build scrapers
of 8 cubic meters struck capacity, which carry 10 m 3 heaped. The largest self-propelled scrapers are of 19 m 3 struck capacity ( 25 m 3 heaped )and they are driven by a tractor engine of 430 horse-powers.
Dumpers are probably the commonest rubber-tyred transport since they can also conveniently be used for carrying concrete or other building materials. Dumpers have the earth container over the front axle on large rubber-tyred wheels, and the container tips forwards on most types, though in articulated dumpers the direction of tip can be widely varied. The smallest dumpers have a capacity of about 0.5 m 3, and the largest standard types are of about 4.5 m 3. Special types include the self-loading dumper of up to 4 m 3and the articulated type of about 0.5 m 3. The distinction between dumpers and dump trucks must be remembered .dumpers tip forwards and the driver sits behind the load. Dump trucks are heavy, strengthened tipping lorries, the driver travels in front lf the load and the load is dumped behind him, so they are sometimes called rear-dump trucks.
2.3 Safety of Structures
The principal scope of specifications is to provide general principles and computational methods in order to verify safety of structures. The “ safety factor ”, which according to modern trends is independent of the nature and combination of the materials used, can usually be defined as the ratio between the conditions. This ratio is also proportional to the inverse of the probability ( risk ) of failure of the structure.
Failure has to be considered not only as overall collapse of the structure but also as unserviceability or, according to a more precise. Common definition. As the reaching of a “ limit state ” which causes the construction not to accomplish the task it was designed for. There are two categories of limit state :
(1)Ultimate limit sate, which corresponds to the highest value of the load-bearing capacity. Examples include local buckling or global instability of the structure; failure of some sections and subsequent transformation of the structure into a mechanism; failure by fatigue; elastic or plastic deformation or creep that cause a substantial change of the geometry of the structure; and sensitivity of the structure to alternating loads, to fire and to explosions.
(2)Service limit states, which are functions of the use and durability of the structure. Examples include excessive deformations and displacements without instability; early or excessive cracks; large vibrations; and corrosion.
Computational methods used to verify structures with respect to the different safety
conditions can be separated into:
(1)Deterministic methods, in which the main parameters are considered as nonrandom parameters.
(2)Probabilistic methods, in which the main parameters are considered as random parameters.
Alternatively, with respect to the different use of factors of safety, computational methods can be separated into:
(1)Allowable stress method, in which the stresses computed under maximum loads are compared with the strength of the material reduced by given safety factors.
(2)Limit states method, in which the structure may be proportioned on the basis of its maximum strength. This strength, as determined by rational analysis, shall not be less than that required to support a factored load equal to the sum of the factored live load and dead load ( ultimate state ).
The stresses corresponding to working ( service ) conditions with unfactored live and dead loads are compared with prescribed values ( service limit state ) . From the four possible combinations of the first two and second two methods, we can obtain some useful computational methods. Generally, two combinations prevail:
(1)deterministic methods, which make use of allowable stresses.
(2)Probabilistic methods, which make use of limit states.
The main advantage of probabilistic approaches is that, at least in theory, it is possible to scientifically take into account all random factors of safety, which are then combined to define the safety factor. probabilistic approaches depend upon :
(1) Random distribution of strength of materials with respect to the conditions of fabrication and erection ( scatter of the values of mechanical properties through out the structure );
(2) Uncertainty of the geometry of the cross-section sand of the structure ( faults and imperfections due to fabrication and erection of the structure );
(3) Uncertainty of the predicted live loads and dead loads acting on the structure;
(4)Uncertainty related to the approximation of the computational method used ( deviation of the actual stresses from computed stresses ).
Furthermore, probabilistic theories mean that the allowable risk can be based on several factors, such as :
(1) Importance of the construction and gravity of the damage by its failure;
(2)Number of human lives which can be threatened by this failure;
土木工程类专业英文文献及翻译
PA VEMENT PROBLEMS CAUSED BY COLLAPSIBLE SUBGRADES By Sandra L. Houston,1 Associate Member, ASCE (Reviewed by the Highway Division) ABSTRACT: Problem subgrade materials consisting of collapsible soils are com- mon in arid environments, which have climatic conditions and depositional and weathering processes favorable to their formation. Included herein is a discussion of predictive techniques that use commonly available laboratory equipment and testing methods for obtaining reliable estimates of the volume change for these problem soils. A method for predicting relevant stresses and corresponding collapse strains for typical pavement subgrades is presented. Relatively simple methods of evaluating potential volume change, based on results of familiar laboratory tests, are used. INTRODUCTION When a soil is given free access to water, it may decrease in volume, increase in volume, or do nothing. A soil that increases in volume is called a swelling or expansive soil, and a soil that decreases in volume is called a collapsible soil. The amount of volume change that occurs depends on the soil type and structure, the initial soil density, the imposed stress state, and the degree and extent of wetting. Subgrade materials comprised of soils that change volume upon wetting have caused distress to highways since the be- ginning of the professional practice and have cost many millions of dollars in roadway repairs. The prediction of the volume changes that may occur in the field is the first step in making an economic decision for dealing with these problem subgrade materials. Each project will have different design considerations, economic con- straints, and risk factors that will have to be taken into account. However, with a reliable method for making volume change predictions, the best design relative to the subgrade soils becomes a matter of economic comparison, and a much more rational design approach may be made. For example, typical techniques for dealing with expansive clays include: (1) In situ treatments with substances such as lime, cement, or fly-ash; (2) seepage barriers and/ or drainage systems; or (3) a computing of the serviceability loss and a mod- ification of the design to "accept" the anticipated expansion. In order to make the most economical decision, the amount of volume change (especially non- uniform volume change) must be accurately estimated, and the degree of road roughness evaluated from these data. Similarly, alternative design techniques are available for any roadway problem. The emphasis here will be placed on presenting economical and simple methods for: (1) Determining whether the subgrade materials are collapsible; and (2) estimating the amount of volume change that is likely to occur in the 'Asst. Prof., Ctr. for Advanced Res. in Transp., Arizona State Univ., Tempe, AZ 85287. Note. Discussion open until April 1, 1989. To extend the closing date one month,
土木工程英文文献
2.1 Reinforced Concrete Plain concrete is formed from a hardened mixture of cement ,water ,fine aggregate, coarse aggregate (crushed stone or gravel),air, and often other admixtures. The plastic mix is placed and consolidated in the formwork, then cured to facilitate the acceleration of the chemical hydration reaction lf the cement/water mix, resulting in hardened concrete. The finished product has high compressive strength, and low resistance to tension, such that its tensile strength is approximately one tenth lf its compressive strength. Consequently, tensile and shear reinforcement in the tensile regions of sections has to be provided to compensate for the weak tension regions in the reinforced concrete element. It is this deviation in the composition of a reinforces concrete section from the homogeneity of standard wood or steel sections that requires a modified approach to the basic principles of structural design. The two components of the heterogeneous reinforced concrete section are to be so arranged and proportioned that optimal use is made of the materials involved. This is possible because concrete can easily be given any desired shape by placing and compacting the wet mixture of the constituent ingredients are properly proportioned, the finished product becomes strong, durable, and, in combination with the reinforcing bars, adaptable for use as main members of any structural system. The techniques necessary for placing concrete depend on the type of member to be cast: that is, whether it is a column, a bean, a wall, a slab, a foundation. a mass columns, or an extension of previously placed and hardened concrete. For beams, columns, and walls, the forms should be well oiled after cleaning them, and the reinforcement should be cleared of rust and other harmful materials. In foundations, the earth should be compacted and thoroughly moistened to about 6 in. in depth to avoid absorption of the moisture present in the wet concrete. Concrete should always be placed in horizontal layers which are compacted by means of high frequency power-driven vibrators of either the immersion or external type, as the case requires, unless it is placed by pumping. It must be kept in mind, however, that over vibration can be harmful since it could cause segregation of the aggregate and bleeding of the concrete. Hydration of the cement takes place in the presence of moisture at temperatures above 50°F. It is necessary to maintain such a condition in order that the chemical hydration reaction can take place. If drying is too rapid, surface
土木工程外文文献及翻译
本科毕业设计 外文文献及译文 文献、资料题目：Designing Against Fire Of Building 文献、资料来源：国道数据库 文献、资料发表（出版）日期：2008.3.25 院（部）：土木工程学院 专业：土木工程 班级：土木辅修091 姓名：武建伟 学号：2008121008 指导教师：周学军、李相云 翻译日期： 20012.6.1
外文文献: Designing Against Fire Of Buliding John Lynch ABSTRACT: This paper considers the design of buildings for fire safety. It is found that fire and the associ- ated effects on buildings is significantly different to other forms of loading such as gravity live loads, wind and earthquakes and their respective effects on the building structure. Fire events are derived from the human activities within buildings or from the malfunction of mechanical and electrical equipment provided within buildings to achieve a serviceable environment. It is therefore possible to directly influence the rate of fire starts within buildings by changing human behaviour, improved maintenance and improved design of mechanical and electrical systems. Furthermore, should a fire develops, it is possible to directly influence the resulting fire severity by the incorporation of fire safety systems such as sprinklers and to provide measures within the building to enable safer egress from the building. The ability to influence the rate of fire starts and the resulting fire severity is unique to the consideration of fire within buildings since other loads such as wind and earthquakes are directly a function of nature. The possible approaches for designing a building for fire safety are presented using an example of a multi-storey building constructed over a railway line. The design of both the transfer structure supporting the building over the railway and the levels above the transfer structure are considered in the context of current regulatory requirements. The principles and assumptions associ- ated with various approaches are discussed. 1 INTRODUCTION Other papers presented in this series consider the design of buildings for gravity loads, wind and earthquakes.The design of buildings against such load effects is to a large extent covered by engineering based standards referenced by the building regulations. This is not the case, to nearly the same extent, in the
土木工程外文翻译
转型衰退时期的土木工程研究 Sergios Lambropoulosa[1], John-Paris Pantouvakisb, Marina Marinellic 摘要 最近的全球经济和金融危机导致许多国家的经济陷入衰退，特别是在欧盟的周边。这些国家目前面临的民用建筑基础设施的公共投资和私人投资显著收缩，导致在民事特别是在民用建筑方向的失业。因此，在所有国家在经济衰退的专业发展对于土木工程应届毕业生来说是努力和资历的不相称的研究，因为他们很少有机会在实践中积累经验和知识，这些逐渐成为过时的经验和知识。在这种情况下，对于技术性大学在国家经济衰退的计划和实施的土木工程研究大纲的一个实质性的改革势在必行。目的是使毕业生拓宽他们的专业活动的范围，提高他们的就业能力。 在本文中，提出了土木工程研究课程的不断扩大，特别是在发展的光毕业生的潜在的项目，计划和投资组合管理。在这个方向上，一个全面的文献回顾，包括ASCE体为第二十一世纪，IPMA的能力的基础知识，建议在其他：显著增加所提供的模块和项目管理在战略管理中添加新的模块，领导行为，配送管理，组织和环境等；提供足够的专业训练五年的大学的研究；并由专业机构促进应届大学生认证。建议通过改革教学大纲为土木工程研究目前由国家技术提供了例证雅典大学。 1引言 土木工程研究（CES）蓬勃发展，是在第二次世界大战后。土木工程师的出现最初是由重建被摧毁的巨大需求所致，目的是更多和更好的社会追求。但是很快，这种演变一个长期的趋势，因为政府为了努力实现经济发展，采取了全世界的凯恩斯主义的理论，即公共基础设施投资作为动力。首先积极的结果导致公民为了更好的生活条件（住房，旅游等）和增加私人投资基础设施而创造机会。这些现象再国家的发展中尤为为明显。虽然前景并不明朗（例如，世界石油危机在70年代），在80年代领先的国家采用新自由主义经济的方法（如里根经济政策），这是最近的金融危机及金融危机造成的后果（即收缩的基础设施投资，在技术部门的高失业率），消除发展前途无限的误区。 技术教育的大学所认可的大量研究土木工程部。旧学校拓展专业并且新的学校建成，并招收许多学生。由于高的职业声望，薪酬，吸引高质量的学校的学生。在工程量的增加和科学技术的发展，导致到极强的专业性，无论是在研究还是工作当中。结构工程师，液压工程师，交通工程师等，都属于土木工程。试图在不同的国家采用专业性的权利，不同的解决方案，，从一个统一的大学学历和广泛的专业化的一般职业许可证。这个问题在许多其他行业成为关键。国际专业协会的专家和机构所确定的国家性检查机构，经过考试后，他们证明不仅是行业的新来者，而且专家通过时间来确定进展情况。尽管在很多情况下，这些证书虽然没有国家接受，他们赞赏和公认的世界。 在试图改革大学研究（不仅在土木工程）更接近市场需求的过程中，欧盟确定了1999博洛尼亚宣言，它引入了一个二能级系统。第一级度（例如，一个三年的学士）是进入
土木工程岩土类毕业设计外文翻译
姓名： 学号： 10447425 X X 大学 毕业设计（论文）外文翻译 （2014届） 外文题目Developments in excavation bracing systems 译文题目开挖工程支撑体系的发展 外文出处Tunnelling and Underground Space Technology 31 (2012) 107–116 学生XXX 学院XXXX 专业班级XXXXX 校内指导教师XXX 专业技术职务XXXXX 校外指导老师专业技术职务 二○一三年十二月
开挖工程支撑体系的发展 1.引言 几乎所有土木工程建设项目（如建筑物，道路，隧道，桥梁，污水处理厂，管道，下水道）都涉及泥土挖掘的一些工程量。往往由于由相邻的结构，特性线，或使用权空间的限制，必须要一个土地固定系统，以允许土壤被挖掘到所需的深度。历史上，许多挖掘支撑系统已经开发出来。其中，现在比较常见的几种方法是：板桩，钻孔桩墙，泥浆墙。 土地固定系统的选择是由技术性能要求和施工可行性（例如手段，方法）决定的，包括执行的可靠性，而成本考虑了这些之后，其他问题也得到解决。通常环境后果（用于处理废泥浆和钻井液如监管要求）也非常被关注（邱阳、1998）。 土地固定系统通常是建设项目的较大的一个组成部分。如果不能按时完成项目，将极大地影响总成本。通常首先建造支撑，在许多情况下，临时支撑系统是用于支持在挖掘以允许进行不断施工，直到永久系统被构造。临时系统可以被去除或留在原处。 打桩时，因撞击或振动它们可能会被赶入到位。在一般情况下，振动是最昂贵的方法，但只适合于松散颗粒材料，土壤中具有较高电阻（例如，通过鹅卵石）的不能使用。采用打入桩系统通常是中间的成本和适合于软沉积物（包括粘性和非粘性），只要该矿床是免费的鹅卵石或更大的岩石。 通常，垂直元素（例如桩）的前安装挖掘工程和水平元件（如内部支撑或绑回）被安装为挖掘工程的进行下去，从而限制了跨距长度，以便减少在垂直开发弯矩元素。在填充情况下，桩可先设置，从在斜坡的底部其嵌入悬挑起来，安装作为填充进步水平元素（如搭背或土钉）。如果滞后是用来保持垂直元素之间的土壤中，它被安装为挖掘工程的进行下去，或之前以填补位置。 吉尔- 马丁等人（2010）提供了一个数值计算程序，以获取圆形桩承受轴向载荷和统一标志（如悬臂桩）的单轴弯矩的最佳纵筋。他们开发的两种优化流程：用一个或两个直径为纵向钢筋。优化增强模式允许大量减少的设计要求钢筋的用量，这些减少纵向钢筋可达到50％相对传统的，均匀分布的加固方案。 加固桩集中纵向钢筋最佳的位置在受拉区。除了节约钢筋，所述非对称加强钢筋图案提高抗弯刚度，通过增加转动惯量的转化部分的时刻。这种增加的刚性可能会在一段时间内增加的变形与蠕变相关的费用。评估相对于传统的非对称加强桩的优点，对称，钢筋桩被服务的条件下全面测试来完成的，这种试验是为了验证结构的可行性和取得的变形的原位测量。 基于现场试验中，用于优化的加强图案的优点浇铸钻出孔（CIDH）在巴塞罗那的
土木工程外文文献翻译
专业资料 学院： 专业：土木工程 姓名： 学号： 外文出处：Structural Systems to resist (用外文写) Lateral loads 附件：1.外文资料翻译译文；2.外文原文。
附件1：外文资料翻译译文 抗侧向荷载的结构体系 常用的结构体系 若已测出荷载量达数千万磅重，那么在高层建筑设计中就没有多少可以进行极其复杂的构思余地了。确实，较好的高层建筑普遍具有构思简单、表现明晰的特点。 这并不是说没有进行宏观构思的余地。实际上，正是因为有了这种宏观的构思，新奇的高层建筑体系才得以发展，可能更重要的是：几年以前才出现的一些新概念在今天的技术中已经变得平常了。 如果忽略一些与建筑材料密切相关的概念不谈，高层建筑里最为常用的结构体系便可分为如下几类： 1.抗弯矩框架。 2.支撑框架，包括偏心支撑框架。 3.剪力墙，包括钢板剪力墙。 4.筒中框架。 5.筒中筒结构。 6.核心交互结构。 7. 框格体系或束筒体系。 特别是由于最近趋向于更复杂的建筑形式，同时也需要增加刚度以抵抗几力和地震力，大多数高层建筑都具有由框架、支撑构架、剪力墙和相关体系相结合而构成的体系。而且，就较高的建筑物而言，大多数都是由交互式构件组成三维陈列。 将这些构件结合起来的方法正是高层建筑设计方法的本质。其结合方式需要在考虑环境、功能和费用后再发展，以便提供促使建筑发展达到新高度的有效结构。这并
不是说富于想象力的结构设计就能够创造出伟大建筑。正相反，有许多例优美的建筑仅得到结构工程师适当的支持就被创造出来了，然而，如果没有天赋甚厚的建筑师的创造力的指导，那么，得以发展的就只能是好的结构，并非是伟大的建筑。无论如何，要想创造出高层建筑真正非凡的设计，两者都需要最好的。 虽然在文献中通常可以见到有关这七种体系的全面性讨论，但是在这里还值得进一步讨论。设计方法的本质贯穿于整个讨论。设计方法的本质贯穿于整个讨论中。 抗弯矩框架 抗弯矩框架也许是低，中高度的建筑中常用的体系，它具有线性水平构件和垂直构件在接头处基本刚接之特点。这种框架用作独立的体系，或者和其他体系结合起来使用，以便提供所需要水平荷载抵抗力。对于较高的高层建筑，可能会发现该本系不宜作为独立体系，这是因为在侧向力的作用下难以调动足够的刚度。 我们可以利用STRESS，STRUDL 或者其他大量合适的计算机程序进行结构分析。所谓的门架法分析或悬臂法分析在当今的技术中无一席之地，由于柱梁节点固有柔性，并且由于初步设计应该力求突出体系的弱点，所以在初析中使用框架的中心距尺寸设计是司空惯的。当然，在设计的后期阶段，实际地评价结点的变形很有必要。 支撑框架 支撑框架实际上刚度比抗弯矩框架强，在高层建筑中也得到更广泛的应用。这种体系以其结点处铰接或则接的线性水平构件、垂直构件和斜撑构件而具特色，它通常与其他体系共同用于较高的建筑，并且作为一种独立的体系用在低、中高度的建筑中。
土木工程外文翻译.doc
项目成本控制 一、引言 项目是企业形象的窗口和效益的源泉。随着市场竞争日趋激烈，工程质量、文明施工要求不断提高，材料价格波动起伏，以及其他种种不确定因素的影响，使得项目运作处于较为严峻的环境之中。由此可见项目的成本控制是贯穿在工程建设自招投标阶段直到竣工验收的全过程，它是企业全面成本管理的重要环节，必须在组织和控制措施上给于高度的重视，以期达到提高企业经济效益的目的。 二、概述 工程施工项目成本控制，指在项目成本在成本发生和形成过程中，对生产经营所消耗的人力资源、物资资源和费用开支，进行指导、监督、调节和限制，及时预防、发现和纠正偏差从而把各项费用控制在计划成本的预定目标之内，以达到保证企业生产经营效益的目的。 三、施工企业成本控制原则 施工企业的成本控制是以施工项目成本控制为中心，施工项目成本控制原则是企业成本管理的基础和核心，施工企业项目经理部在对项目施工过程进行成本控制时，必须遵循以下基本原则。 3.1 成本最低化原则。施工项目成本控制的根本目的，在于通过成本管理的各种手段，促进不断降低施工项目成本，以达到可能实现最低的目标成本的要求。在实行成本最低化原则时，应注意降低成本的可能性和合理的成本最低化。一方面挖掘各种降低成本的能力，使可能性变为现实；另一方面要从实际出发，制定通过主观努力可能达到合理的最低成本水平。 3.2 全面成本控制原则。全面成本管理是全企业、全员和全过程的管理，亦称“三全”管理。项目成本的全员控制有一个系统的实质性内容，包括各部门、各单位的责任网络和班组经济核算等等，应防止成本控制人人有责，人人不管。项目成本的全过程控制要求成本控制工作要随着项目施工进展的各个阶段连续 进行，既不能疏漏，又不能时紧时松，应使施工项目成本自始至终置于有效的控制之下。 3.3 动态控制原则。施工项目是一次性的，成本控制应强调项目的中间控制，即动态控制。因为施工准备阶段的成本控制只是根据施工组织设计的具体内容确
土木工程专业外文文献及翻译
（ 二 〇 一 二 年 六 月 外文文献及翻译 题 目： About Buiding on the Structure Design 学生姓名： 学 院：土木工程学院 系 别：建筑工程系 专 业：土木工程(建筑工程方向) 班 级：土木08-4班 指导教师：
英文原文： Building construction concrete crack of prevention and processing Abstract The crack problem of concrete is a widespread existence but again difficult in solve of engineering actual problem, this text carried on a study analysis to a little bit familiar crack problem in the concrete engineering, and aim at concrete the circumstance put forward some prevention, processing measure. Keyword:Concrete crack prevention processing Foreword Concrete's ising 1 kind is anticipate by the freestone bone, cement, water and other mixture but formation of the in addition material of quality brittleness not and all material.Because the concrete construction transform with oneself, control etc. a series problem, harden model of in the concrete existence numerous tiny hole, spirit cave and tiny crack, is exactly because these beginning start blemish of existence just make the concrete present one some not and all the characteristic of quality.The tiny crack is a kind of harmless crack and accept concrete heavy, defend Shen and a little bit other use function not a creation to endanger.But after the concrete be subjected to lotus carry, difference in temperature etc. function, tiny crack would continuously of expand with connect, end formation we can see without the
土木工程毕业设计外文翻译最终中英文
7 Rigid-Frame Structures A rigid-frame high-rise structure typically comprises parallel or orthogonally arranged bents consisting of columns and girders with moment resistant joints. Resistance to horizontal loading is provided by the bending resistance of the columns, girders, and joints. The continuity of the frame also contributes to resisting gravity loading, by reducing the moments in the girders. The advantages of a rigid frame are the simplicity and convenience of its rectangular form.Its unobstructed arrangement, clear of bracing members and structural walls, allows freedom internally for the layout and externally for the fenestration. Rig id frames are considered economical for buildings of up to' about 25 stories, above which their drift resistance is costly to control. If, however, a rigid frame is combined with shear walls or cores, the resulting structure is very much stiffer so that its height potential may extend up to 50 stories or more. A flat plate structure is very similar to a rigid frame, but with slabs replacing the girders As with a rigid frame, horizontal and vertical loadings are resisted in a flat plate structure by the flexural continuity between the vertical and horizontal components. As highly redundant structures, rigid frames are designed initially on the basis of approximate analyses, after which more rigorous analyses and checks can be made. The procedure may typically inc lude the following stages: 1. Estimation of gravity load forces in girders and columns by approximate method. 2. Preliminary estimate of member sizes based on gravity load forces with arbitrary increase in sizes to allow for horizontal loading. 3. Approximate allocation of horizontal loading to bents and preliminary analysis of member forces in bents. 4. Check on drift and adjustment of member sizes if necessary. 5. Check on strength of members for worst combination of gravity and horizontal loading, and adjustment of member sizes if necessary. 6. Computer analysis of total structure for more accurate check on member strengths and drift, with further adjustment of sizes where required. This stage may include the second-order P-Delta effects of gravity loading on the member forces and drift.. 7. Detailed design of members and connections.
土木工程外文翻译参考3篇
学校 毕业设计（论文）附件 外文文献翻译 学号： xxxxx 姓名： xxx 所在系别： xxxxx 专业班级： xxx 指导教师： xxxx 原文标题： Building construction concrete crack of prevention and processing 2012年月日 .
建筑施工混凝土裂缝的预防与处理1 摘要 混凝土的裂缝问题是一个普遍存在而又难于解决的工程实际问题，本文对混凝土工程中常见的一些裂缝问题进行了探讨分析，并针对具体情况提出了一些预防、处理措施。 关键词：混凝土裂缝预防处理 前言 混凝土是一种由砂石骨料、水泥、水及其他外加材料混合而形成的非均质脆性材料。由于混凝土施工和本身变形、约束等一系列问题，硬化成型的混凝土中存在着众多的微孔隙、气穴和微裂缝，正是由于这些初始缺陷的存在才使混凝土呈现出一些非均质的特性。微裂缝通常是一种无害裂缝，对混凝土的承重、防渗及其他一些使用功能不产生危害。但是在混凝土受到荷载、温差等作用之后，微裂缝就会不断的扩展和连通，最终形成我们肉眼可见的宏观裂缝，也就是混凝土工程中常说的裂缝。 混凝土建筑和构件通常都是带缝工作的，由于裂缝的存在和发展通常会使内部的钢筋等材料产生腐蚀，降低钢筋混凝土材料的承载能力、耐久性及抗渗能力，影响建筑物的外观、使用寿命，严重者将会威胁到人们的生命和财产安全。很多工程的失事都是由于裂缝的不稳定发展所致。近代科学研究和大量的混凝土工程实践证明，在混凝土工程中裂缝问题是不可避免的，在一定的范围内也是可以接受的，只是要采取有效的措施将其危害程度控制在一定的范围之内。钢筋混凝土规范也明确规定：有些结构在所处的不同条件下，允许存在一定宽度的裂缝。但在施工中应尽量采取有效措施控制裂缝产生，使结构尽可能不出现裂缝或尽量减少裂缝的数量和宽度，尤其要尽量避免有害裂缝的出现，从而确保工程质量。 混凝土裂缝产生的原因很多，有变形引起的裂缝：如温度变化、收缩、膨胀、不均匀沉陷等原因引起的裂缝；有外载作用引起的裂缝；有养护环境不当和化学作用引起的裂缝等等。在实际工程中要区别对待，根据实际情况解决问题。 混凝土工程中常见裂缝及预防: 1.干缩裂缝及预防 干缩裂缝多出现在混凝土养护结束后的一段时间或是混凝土浇筑完毕后的一周左右。水泥浆中水分的蒸发会产生干缩，且这种收缩是不可逆的。干缩裂缝的产生主要是由于混凝土内外水分蒸发程度不同而导致变形不同的结果：混凝土受外部条件的影响，表面水分损失过快，变形较大，内部湿度变化较小变形较小，较大的表面干缩变形受到混凝土内部约束，产生较大拉应力而产生裂缝。相对湿度越低，水泥浆体干缩越大，干缩裂缝越易产 1原文出处及作者：《加拿大土木工程学报》
土木工程毕业设计中英文翻译
附录：中英文翻译 英文部分： LOADS Loads that act on structures are usually classified as dead loads or live loads are fixed in location and constant in magnitude throughout the life of the the self-weight of a structure is the most important part of the structure and the unit weight of the density varies from about 90 to 120 pcf (14 to 19 KN/m)for lightweight concrete,and is about 145 pcf (23 KN/m)for normal calculating the dead load of structural concrete,usually a 5 pcf (1 KN/m)increment is included with the weight of the concrete to account for the presence of the reinforcement. Live loads are loads such as occupancy,snow,wind,or traffic loads,or seismic may be either fully or partially in place,or not present at may also change in location. Althought it is the responsibility of the engineer to calculate dead loads,live loads are usually specified by local,regional,or national codes and sources are the publications of the American National Standards Institute,the American Association of State Highway and Transportation Officials and,for wind loads,the recommendations of the ASCE Task Committee on Wind Forces. Specified live the loads usually include some allowance for overload,and may include measures such as posting of maximum loads will not be is oftern important to distinguish between the