UA5000脚本

sysname XXXXXXXX
加框加板及配置端口模式
frame add 0 0

frame add 1 9

frame connect 0 1//连接主从框

增加单板：
board batadd 0/6 0/16 a32
board add 0/17 tss
board batadd 0/18 0/35 a32
board confirm 0 确认单板

1.配置端口模式

up-linkport set workmode eth1
fe mode active eth1 100mfull

fe mode standby eth1 100mfull

修改IP地址：
interface eth

ip modify 172.20.1.2 ip_address 10.49.26.252 submask 255.255.255.248 gateway 10.49.26.249 vlan_tag 1690


2.配置相关参数
alarm alarmlevel 0x1c100007 major

qos threshold jitter 20 loopdelay 100 packetlost 1

modem parameters eventmode 0

fax parameters tranmode 2

time time-stamp local

uplink tps on


3.H248接口数据以及配置MG用户
interface h248 0
y

if-h248 attribute code text domainName dazha-AG01 mgip 10.49.26.252 mgport 2944 transfer alf/udp mgcip_1 10.49.0.71 mgcport_1 2944 mg-media-ip 10.49.26.252


digitmap-timer start 20
digitmap-timer short 3
digitmap-timer long 3
digitmap-timer duration 4000
digitmap set inner [2-8]xxxxxx

mg-ringmode add 0 0 4

if-h248 attribute heartBeatgenTimer 5 heartBeatRetransTimes 5 heartBeatRetransTimer 3


reset coldstart
y

quit

esl user
mgpstnuser batadd 0/6/0 0/16/31 0 terminalid 0

mgpstnuser batadd 0/18/0 0/35/31 0 terminalid 352

pstnport reversepole_pulse batset 0/%d/0 0/%d/31 300 enable

pstnport attribute batset 0/%d/0 0/%d/31 polarity-reverse support

pstnport attribute batset 0/7/0 0/7/31 polarity-reverse support

4.环境监控(h303esc)
emu add 0 h303esc 0 30 RS232 dazha

esc digital 2 available-level high-level name fan digital-alarm 13 风扇告警JDT1

esc digital 3 available-level low-level name fan digital-alarm 13 风扇告警JDT2 #

esc digital 9 available-level low-level name water digital-alarm 16 水浸告警JDT8 #

esc digital 8 available-level high-level name flog digital-alarm 15 烟雾告警JDT7

5.环境监控设置(电源监控4845)
emu add 0 poWER4845 0 0 rs232

interface emu 0

power battery parameter 0.15 60 1 100 (配置蓄电池参数)

power battery temperature 60 -40 100 (配置蓄电池参数)

power environment temperature 62 0 80 -20 (设置温度参数)

power environment humidity 80 10 100 0 (设置湿度参数)

power outside_digital 0 low-level Masterframe_fan (配置扩展数字监控量)

power outside_digital 3 low-level SPD

power outside_digital 4 high-level Smoke

power outside_digital 5 high-level Heat_Exchanger


如果采用220V的电源系统，该步骤无需配置；如果采用110V系统，需要进行如下配置.
power supply-parameter 180 90 58 45


6.网管设置

snmp-agent local-engineid 800007DB03001882BE2F7D
y

snmp-agent community read public

snmp-agent community write private

snmp-agent sys-info contact Telecom-07578222

1196

snmp-agent sys-info location shunde

snmp-agent sys-info version v1 v2c

snmp-agent target-host trap address 132.110.33.40 securityname private v1

snmp-agent trap enable standard

10.49.1.253 （带内报文发送地址）
132.110.33.41(带外报文发送地址 禅城和其他)
132.110.33.40（顺德带外）

oversea parameters 4 80
oversea parameters 3 800

autosave interval 1440

undo rollback active
y

undo rollback standby
y

南海要求
oversea parameters 4 50
oversea parameters 3 700

禅城三水高明要求
oversea parameters 4 50
oversea parameters 3 500

顺德
oversea parameters 4 80
oversea parameters 3 800

9.最后要保存
save


带外网管：
interface outband
ip address 132.116.36.175 255.255.255.128 132.116.36.254
quit

(config)#diagnose
(diagnose)%%outband route add 132.116.0.0 255.255.0.0
(diagnose)%%outband route add 132.110.0.0 255.255.0.0

display outband route table
(diagnose
outband route add 增加带外网管路由PVMD的主控板)

外线测试：
test
pots loop-line-test v5id 2 l3add 417

---------------------------------------------------------------------------------------------------------------------------------------------------
V5部分配置：

阻抗的设定
(config)#interface pvm 0/4
(config-if-pvm-0/4)#impedance 0 75
(config-if-pvm-0/4)#impedance 1 75
(config-if-pvm-0/4)#impedance 2 75
(config-if-pvm-0/4)#impedance 3 75

(config)#interface pvm 0/5
(config-if-pvm-0/5)#impedance 0 75
(config-if-pvm-0/5)#impedance 1 75
(config-if-pvm-0/5)#impedance 2 75
(config-if-pvm-0/5)#impedance 3 75

CRC4校验(交换机为华为设备时不用做crc4验证，此处上联是NEC交换机要做crc4验证)
(config)#interface pvm 0/4
(config-if-pvm-0/4)#crc4 0
(config-if-pvm-0/4)#crc4 1

(config)#interface pvm 0/5
(config-if-pvm-0/5)#crc4 0
(config-if-pvm-0/5)#crc4 1

增加V5接口及链路
(config)#interface v5 0 (V5ID)
(config-if-v5-4)#if-v5 attribute an_v5 v52 0 0 linkidentify failures yes reprovision yes startup yes timing yes （第一个0是变量编码Variable code，第二个0是pstnid）

(config-if-v5-4)#link add 0/4/0 0
(config-if-v5-4)#link add 0/4/1 1

(config-if-v5-4)#link add 0/5/0 2
(config-if-v5-4)#link add 0/5/1 3

c通道标识0

增加C通道
(config-if-v5-4)#c-channel add 0/4/0 tsno 16 1:protc1_act 0（logiccid是0=pstnid）
(config-if-v5-4)#c-channel add 0/5/0 tsno 16 2:protc1_std


V5参数的设定
(config-if-v5-4)#v5-software parameters modify 19 100

(config-if-v5-4)#reset

时钟源配置
(config)#clock source 0 E1 0/4/0

(config)#clock source 1 E1 0/5/0

(config)#clock priority 0/1 //设置时钟优先级成功
(config)#save

增加PSTN用户
(config)#narrow user
(config-narrow-user)#pstnuser batadd 0/18/0

0/35/31 0 352
pstnport reversepole_pulse batset 0/6/0 0/6/31 300 enable

pstnport attribute batset 0/6/0 0/6/31 polarity-reverse support