文档库

最新最全的文档下载
当前位置:文档库 > orinoco AP-700设置说明

orinoco AP-700设置说明

orinoco AP-700设置说明

orinoco AP-700设置说明

orinoco AP-700设置说明

t.

2Connect the Cables

1.Provide power to the unit as follows:

A. A. If not using PoE, plug the power cord into the power jack and

connect

B.the unit to an AC power outlet (100/240V, 50-60Hz).

C. B. If using PoE, connect power to the unit from a DC injector

device, such as the 1-Port Active Ethernet DC Injector hub.

Note:Note: If you are installing the AP in a plenum, you

must use PoE.

2.Optionally, connect an RS-232 cable to the RS-232 console port.

3.Wait for the power LED to turn green before proceeding.

4.Connect the AP-700 LAN port to a stand-alone PC using a cross-

over Ethernet cable, or to a network hub or switch.

5.When the RS-232 cable is not connected, you may optionally install a

security cover to prevent access to the power and LAN ports, and the

reset and reload buttons:

—Slide the hinging end of the security cover into the hole on the

rear panel of the AP-700 to the left of the connectors.

—Use two screws to attach the right side of the security cover to

orinoco AP-700设置说明

the RS-232 screw holes on the rear panel of the AP-700.

3 Initialize the AP-700

There are two ways to initialize the AP:

A.

orinoco AP-700设置说明

If the AP is connected to a stand-alone PC using the cross-over

Ethernet cable and is in its factory default configuration state,

s ee Option A

orinoco AP-700设置说明

below.

B.If the AP is connected to a DHCP server

orinoco AP-700设置说明

on the same subnet as

your computer, s ee Option B below.

Option A:

1.Ensure there is no DHCP server running on the PC.

2.Set the IP address of the PC to 169.254.x.y (where x and y can be

any number between 1 and 254).

3.Set the subnet mask of the PC to 255.255.0.0.

4.

orinoco AP-700设置说明

Note that you will use the unit’s default IP address (169.254.128.132)

for configuration.

orinoco AP-700设置说明

5.Proceed to Basic Configuration.

Option B:

1.Select Start > All Programs > ORiNOCO > ScanTool. ScanTool

will discover the access point and display the IP address to use for

configuration.

2.Note the IP address displayed and click the

orinoco AP-700设置说明

Cancel button, OR

Click the Change button and then the Web Configuration button.

3.Proceed to Basic Configuration.

4 Basic Configuration

1.Open your browser and enter the IP Address configured in Step 3.

Press Enter. Result: The AP-700 Login screen appears.

2.Leave the user name field empty, enter your password (default is

public), and click OK. Result: The System Status screen appears.

3.Click the Configure button. Result: The System Configuration

screen appears. Each tab contains information for specific

configuration categories.

4. If your AP model number ends in -WD, select the System tab and

choose the installation Country and location (indoor/outdoor). This

step is not required for model numbers not ending in -WD.

1

4

3

2 (optional)

4

3

2

orinoco AP-700设置说明

orinoco AP-700设置说明

AP-700 Quick Installation Guide

orinoco AP-700设置说明

5.Select the Interfaces

orinoco AP-700设置说明

tab.

6.Select the Wireless tab.

7.Enter a primary Network Name (SSID). You can later configure

multiple SSID/VLAN pairs (up to 16) and define security profiles for

each pair. Refer to the AP-700 User Guide for more information..

5Association Test

1.Install a wireless card in a laptop or other computer, including the

drivers and the management software.

2.Configure the card to match the network name and encryption key of

one of the wireless interfaces on the AP-700 unit.

3.Verify that your Client Manager application shows association with

the AP-700 device.

6Install Software and Documentation

Insert the CD into your computer’s CD-ROM drive and install the

software and documentation.

The Scan Tool program, Help files, and User Guide are added to

the Start > All Programs > ORiNOCO menu.

In addition, software and documentation are installed in the following

locations:

?ScanTool: C:\Program Files\ORiNOCO\AP-700.

?Help files: C:\Program Files\ORiNOCO\AP-700\HTML

?User Guide: C:\Program Files\ORiNOCO\AP-700\PDF

?Safety and Regulatory Compliance Guide:

C:\Program Files\ORiNOCO\AP-700\PDF

Accessing the Command Line Interface

Ethernet Port

To use the CLI through the Ethernet port, you must have a telnet

program, the CLI password, and the unit’s IP address.

To access the unit through Ethernet on a Windows PC

1.Open a DOS command window: from the Windows Start menu,

select Run; enter cmd.

2.In the DOS window displayed, enter telnet and the IP address (e.g.

telnet 10.0.0.1).

3.Click OK to start the telnet program; you are prompted for your

password.

4.Enter the password (the default password is public).

Technical Support

Proxim eService Web Site Support

The Proxim eService Web site is available 7x24x365 at: http://

http://www.wendangku.net/doc/2e894ddf5022aaea998f0f39.html

Telephone Support

Contact for technical support via telephone as follows:

?US and Canada: 408-383-7700 (8.00AM-6.00PM)

?APAC Countries: +91 40 23115490 (9.00AM-6.00PM)

?International: 408-383-7700 (8.00AM-6.00PM)

ServPak Support

?Advanced Replacement

?Extended Warranty

?7x24x365 Technical Support

?Priority Queuing

To learn more, please call Proxim Support at 408-383-7700 or send an

email to servpak@http://www.wendangku.net/doc/2e894ddf5022aaea998f0f39.html. To purchase ServPak support services,

please contact your authorized Proxim distributor.

What is in the Kit

?AP-700 unit with integrated 802.11a/b/g radio and Power over

Ethernet (PoE) support

?Mounting plate for wall or ceiling mounting

?Security cover

?Power adapter

?CD-ROM containing software and documentation

Additional Items Required

?Windows?95 or higher PC with CD-ROM drive

? A cross-over Ethernet cable to initialize the unit

?Microsoft? IE 6 with Service Pack 1 or later and patch Q323308 or

Netscape? 7.1 or higher web browser

1Mount the AP-700

Conduct a site survey to determine the best location for your device.

Once you have chosen a final location for your unit, mount the AP-700 to

a wall or a T-bar ceiling as follows:

To mount the AP-700 to a ceiling

1.Attach the mounting plate to the bottom of the AP-700 by lining up

the keyholes and attaching it with two screws.

2.Snap the tabs onto the ceiling T-bar. Rotate the AP-700 until it snaps

on to the T-bar.

To mount the AP-700 to a wall

1.Put the mounting plate up to the wall. The knobs that fit into the

keyholes on the AP-700 should be in a vertical line.

2.Screw through the mounting plate.

3.Place the AP up against the mounting plate. Orient the AP with the

long access vertical, with the connectors facing right.

You can optionally install external antennas on the AP-700. Refer to the

AP-700 User Guide for installation instructions..

IMPORTANT

This device must be installed by a trained professional, value added

reseller or systems integrator who is familiar with RF planning issues

and the regulatory limits.

CAUTION!

Heed all the WARNINGS. Follow all the instructions. Do not defeat the

safety purpose of the grounding. Only use attachments/accessories

specified by the manufacturer.

1561 Buckeye Drive, Milpitas, California 95035

Phone: (408) 383-7600 , Fax: (408) 383-7680

http://www.wendangku.net/doc/2e894ddf5022aaea998f0f39.html

PN 75339 1 ? 2008 Proxim Wireless Corporation

6

5