rev 02.24.05
Technical Support: (888) 41-ASTEC or (407) 241-2752
Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211
Asia (HK) 852-2437-96622
350-1400 Watts
HPS35 Series
Total p p ower:350W Input v v oltage: 90-2264VAC # o o f o o utputs: One && s s tandby
ASIA
Units 2111-2116, Level 21Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories
Hong Kong
Telephone: 852-2437-9662Facsimile: 852-2402-4426
E U R O P E
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211Facsimile: 44 (1384) 843-355
A M E R I C A S
5810 Van Allen Way Carlsbad, CA 92008Telephone: 760-930-4600
Facsimile: 760-930-0698
https://www.wendangku.net/doc/305622162.html,
Module Max. Size Max. Module
Number Unit Code (H x W x L)Power
per Rack Weight (lbs)
HPS35
1.6" x 4.3" x 10.5"
350 W
4
3.2
H P S 35L -N N N R -0000
HPS35
North America (USA): 1-888-41-ASTEC Europe (UK): 44 (1384) 842-211Asia (HK): 852-2437-9662
154
rev 02.24.05
1A B C
D E F
H J
K L
M N P
R S T U V
W X
Y Z
AA AB
2345678
9101112131415161718192021222324Mating c c onnector:
EDAC 307-048-520-201 or equivalent
Rating: 5A per contact
P i n 66 - S S W P (IN/OUT Signal)(S i n g l e W W i r e P P a r a l l e l )
SWP Pin is used when
connecting units in parallel to achieve current sharing.Current share accuracy is typically 10% of full load.
P i n 223 - F F a n M M o n i t o r (OUT Signal)
P i n Z Z - A A C O O K (OUT Signal)
P i n F F - --R R e m o t e S S e n s e P i n H H - ++ R R e m o t e S S e n s e
Compensates for up to 0.5V drop.Recommended shielded twisted wire pair.
P i n X X - M M o d u l e I I n h i b i t (IN Signal)
Note:
SWP Voltage is 5V at 100% load current Note:
Hi state: Source 100uA @ 4V Low State: Sink 10mA @ 0.5V
P i n A A A - D D C O O K (OUT Signal)
Unit C C onnector
Card Edge Connector with gold fingers double-sided 1.6mm FR-4 PCB
E U R O P E
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211Facsimile: 44 (1384) 843-355
A M E R I C A S
5810 Van Allen Way Carlsbad, CA 92008Telephone: 760-930-4600Facsimile: 760-930-0698
155
https://www.wendangku.net/doc/305622162.html,
ASIA
Units 2111-2116, Level 21Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories
Hong Kong
Telephone: 852-2437-9662Facsimile: 852-2402-4426
HPS35 Series
DRAWINGS
H P R 1 -000
System Max. Size Max. System Module Standard Unit Code (H x W x L)Power Distribution Size Weight (lbs.)
HPR1
1.75" x 19.0" x 13.0"
1400 W
(4 ea) HPS35
1U
8.6
P i n 22 ++ R R e m o t e S S e n s e P i n 33 - R R e m o t e S S e n s e
Compensates for up to 0.5V drop.Recommended shielded twisted wire pair.
P i n 112 - G G l o b a l A A C O O K (OUT signal)
Note: AC OK signals are OR'ed together internally. If any module fails, the LED on the affected module will be off and the logic signal will indicate AC NOT OK.P i n 119 - G G l o b a l I I n h i b i t (IN signal)
Note: All outputs disabled when Pin 19is open or High.
P i n 222 - S S W P (IN/OUT signal)
SWP Pin is used when connecting racks in parallel to achieve
current sharing. Current share accuracy is
typically 10% of full load.Note:SWP Voltage is 5V at 100% load current.
M o d u l e I I n h i b i t (IN Signal)
Note: Module Inhibit signals for each slot in the rack is accessible in the D-sub connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 is the Return Pin.
North America (USA): 1-888-41-ASTEC Europe (UK): 44 (1384) 842-211Asia (HK): 852-2437-9662
156
rev 02.24.05
D C O O K (OUT Signal)
Note: DC OK signals for each slot in the rack is accessible in the D-sub
connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1is the Return Pin.
A C O O K (OUT Signal)
Note: AC OK signals for each slot in the rack is accessible in the D-sub
connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1is the Return Pin.
Hi state: Source 100uA @ 4V Low State: Sink 10mA @ 0.5V
F a n M M o n i t o r (OUT Signal)Note:Fan Monitor signals for each slot
in the rack is accessible in the D-sub connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1is the Return Pin.I2C_ADD#1I2C_ADD#2TBD