hp 3par 初始化安装
(none) login: consle
Password:
用户名/密码 console/cmp43pd
login: console
Password:
Usage of the 3PAR(R) InForm(tm) Operating System is subject to the terms of
the End-User License Agreement (EULA), with the exclusion of software licensed
under other terms. The EULA can be found in /usr/share/doc/tpd/copyright.
Many of the programs included with the 3PAR InForm(tm) Operating System are
freely redistributable; the exact distribution terms for each program
are described in the individual files in /usr/share/doc/*/copyright.
No directory, logging in with HOME=/
3PAR Console Menu 1627110-0 3.2.1.46
1. Out Of The Box Procedure
2. Re-enter network configuration
3. Update the CBIOS
4. Enable or disable CLI error injections
5. Perform a Node-to-Node rescue
6. Set up the system to wipe and rerun ootb
7. Cancel a wipe
8. Perform a deinstallation
9. Update the system for recently added hardware (admithw)
10. Check system health (checkhealth)
11. Exit
> 1
It appears your Cluster is in a proper manual startup state to proceed.
Removing VMs
Welcome to the Out-Of-The-Box Experience 3.2.1.46
*****************************************************************************
*****************************************************************************
* *
* CAUTION!! CONTINUING WILL CAUSE COMPLETE AND IRRECOVERABLE DATA LOSS *
* *
*****************************************************************************
*****************************************************************************
You need to have the InServ network config information available.
This can be obtained from the Systems Assurance Document.
DO YOU WISH TO CONTINUE? yes/no ==> yes
Cluster has the following nodes:
Node 0
Node 1
Enter < C > to continue or < Q > to quit ==> c
Please identify a location so that time zone rules can be set correctly.
Please select a continent or ocean.
1) Africa
2) Americas
3) Antarctica
4) Arctic Ocean
5) Asia
6) Atlantic Ocean
7) Australia
8) Europe
9) Indian Ocean
10) Pacific Ocean
11) none - I want to specify the time zone using the Posix TZ format.
#? 5
Please select a country.
1) Afghanistan 18) Israel 35) Palestine
2) Armenia 19) Japan 36) Philippines
3) Azerbaijan 20) Jordan 37) Qatar
4) Bahrain 21) Kazakhstan 38) Russia
5) Bangladesh 22) Korea (North) 39) Saudi Arabia
6) Bhutan 23) Korea (South) 40) Singapore
7) Brunei 24) Kuwait 41) Sri Lanka
8) Cambodia 25) Kyrgyzstan 42) Syria
9) China 26) Laos 43) Taiwan
10) Cyprus 27) Lebanon
44) Tajikistan
11) East Timor 28) Macau 45) Thailand
12) Georgia 29) Malaysia 46) Turkmenistan
13) Hong Kong 30) Mongolia 47) United Arab Emirates
14) India 31) Myanmar (Burma) 48) Uzbekistan
15) Indonesia 32) Nepal 49) Vietnam
16) Iran 33) Oman 50) Yemen
17) Iraq 34) Pakistan
#? 9
Please select one of the following time zone regions.
1) east China - Beijing, Guangdong, Shanghai, etc.
2) Heilongjiang (except Mohe), Jilin
3) central China - Sichuan, Yunnan, Guangxi, Shaanxi, Guizhou, etc.
4) most of Tibet & Xinjiang
5) west Tibet & Xinjiang
#? 1
The following information has been given:
China
east China - Beijing, Guangdong, Shanghai, etc.
Therefore TZ='Asia/Shanghai' will be used.
Local time is now: Mon Aug 17 11:49:52 CST 2015.
Universal Time is now: Mon Aug 17 03:49:52 UTC 2015.
Is the above information OK?
1) Yes
2) No
#? 1
You can make this change permanent for yourself by appending the line
TZ='Asia/Shanghai'; export TZ
to the file '.profile' in your home directory; then log out and log in again.
Here is that TZ value again, this time on standard output so that you
can use the /usr/bin/tzselect command in shell scripts:
Updating all nodes to use timezone Asia/Shanghai...
Timezone set successfully.
Setting TOD on all nodes.
Current date according to the system: Mon Aug 17 11:49:57 CST 2015
Enter dates in MMDDhhmmYYYY format. For example, 0318******** would
be March 18, 2002 10:57 PM.
Enter the correct date and time, or just press enter to accept
the date shown above. ==>
Enter the InServ system name ==> 111111
Cluster will be initialized with the name < 111111 >
IS THIS THE CORRECT NAME? yes/change ==> yes
Cluster is being initialized with the name < 111111 > ...Please Wait...
Please verify your InForm OS versions are correct.
Release version 3.2.1.46
Patches: None
Component Name Version
CLI Server 3.2.1.46
CLI Client 3.2.1.46
System Manager 3.2.1.46
Kernel 3.2.1.46
TPD Kernel Code 3.2.1.46
Enter < C > to continue or < Q > to quit ==> c
Examining the port states...
All ports are in acceptable states.
Examining state of new disks...
Found < 8 > HCBRE0900GBAS10K disks
Cluster has < 8 > total disks in < 8 > magazines.
< 8 > are new and have unexpected issues.
Now would be the time to fix any disk problems.
Enter < C > to continue or < Q > to quit ==> c
Ensuring all ports are properly connected before continuing... Please Wait...
Cages appear to be connected correctly, continuing.
Examining drive cage firmware... Please wait a moment...
All disks have current firmware.
Issuing admitpd... Please wait a moment...
admitpd completed with the following results...
Found < 8 > HCBRE0900GBAS10K disks
Cluster has < 8 > total disks in < 8 > magazines.
< 8 > are valid.
At this point, it is recommended that the OOTB stress test be started. This
will run heavy I/O on the PDs for 1 hour following 1 hour of chunklet
initialization. The stress test will stop in approximately 2 hours and 15
minutes. Chunklet initialization may continue even after the stress test
completes. Failures will show up as slow disk events.
Do you want to start the test (y/n)? ==> y
Starting system stress test...
Checking for drive table upgrade packages
System has less cages than nodes; using -ha mag for admin volume
Creating admin volume.
Failed --
... will retry in roughly 30 seconds.
... re-issuing the request
Checking for drive table upgrade packages
System has less cages than nodes; using -ha mag for System Reporter data volume
Creating .srdata volume.
Failed --
... will retry in roughly 30 seconds.
... re-issuing the request
Failed --
... will retry in roughly 187 seconds.
... re-issuing the request
Failed --
... will retry in roughly 46 seconds.
... re-issuing the request
Creating SSL certificate ...
SSL certificate has been created. Subject and SHA1 fingerprint
shown below need to be known to users when they first connect
to this HP 3PAR Storage System.
Subject: CN=HP_3PAR 7200-1627110
Fingerprint: c2c8ae6fb8b13f8c3da3e4eb8dea309630efdf6f
Enter < C > to continue ==>
Enter < C > to continue ==> c
InServ Network Configuration
This system has only 2 nodes, so only 1 IP address is supported.
Select IP address type you want to assign:
1: IPv4 Address
2: Both IPv4 and IPv6 Address
> 1
IPv4 Address: 192.168.0.1
Netmask [255.255.255.0]:
Please specify a gateway IP address (enter for default of 192.168.0.1,
"none" if none):
none
Please specify speed (10, 100 or 1000) and duplex (half or full), or auto
to use autonegotiation: auto
NTP server's IP address (enter if none): none
Invalid entry.
NTP server's IP address (enter if none):
DNS server's IP address (enter if none):
Disabling non-encrypted ports will disable SP event handling,
Recovery Manager for VMWare and SRA. Disabling SP event handling will
prevent support personnel from being notified of system problems.
Disabling non-encrypted ports should only be done if there is a strict
requirement for all connections to be encrypted.
Disable non-encrypted ports? [y/n] n
Please verify the following:
IPv4 Address: 192.168.0.1
Netmask: 255.255.255.0
IPv6 Address: ::/0
Nodes: 0 1 2 3 4 5 6 7
Speed and duplex will be autonegotiated.
No NTP server.
No DNS server.
Non-encrypted ports are enabled.
Does this appear to be
correct? [y/n] y
Updated netc configuration in the PR.
SIGHUP has been sent to the netc controller. The network configuration
should reach the new state momentarily.
Checking for active ethernet interface...
Active ethernet interface found.
Checking for drive table upgrade packages
System has less cages than nodes; using -ha mag for logging LDs.
Creating logging LD for node 0.
Creating logging LD for node 1.
Checking for drive table upgrade packages
System has less cages than nodes; using -ha mag for preserved data LDs.
Creating 256 MB of preserved metadata storage on nodes 0 and 1.
Creating 7936 MB of preserved data storage on nodes 0 and 1.
Failed --
1 chunklet out of 24 is not clean yet
... will retry in roughly 5 seconds
... re-issuing the request
The logging LDs have been properly created.
Creating system tasks
Checking for drive table upgrade packages
Creating scheduled task check_slow_disk
Creating scheduled task remove_expired_vvs
Creating scheduled task move_back_chunklet
Creating scheduled task sample
Creating scheduled task checkiperfserver
Creating extended roles
Checking for drive table upgrade packages
Checking if the rights assigned to extended roles need to be updated...
create role updated
basic_edit role updated
3PAR_AO role updated
3PAR_RM role updated
audit role updated
Calculating space usage of sparing algorithms...
Select one of the following spare chunklet selection algorithms:
Minimal: About 13% of the system chunklets will be used.
Default: About 25% of the system chunklets will be used.
Maximal: About 13% of the system chunklets will be used.
Custom allows specifying the exact number of chunklets, but is not recommended
as spares must be manually added when new disks are added.
Enter "Ma" for maximal, "D" for default, "Mi" for minimal, or "C" for custom: d
Selecting spare chunklets...
Checking for drive table upgrade packages
Rebalancing and adding FC spares...
FC spare chunklets rebalanced; number of FC spare chunklets increased by 1638 for a total of 1638.
Rebalancing and adding NL spares...
No NL PDs present
Rebalancing and adding SSD spares...
No SSD PDs present
Please verify that the correct license features are enabled:
License key was generated on Fri Dec 19 09:11:56 2014
System is licensed for 8 disks.
License features currently enabled:
3PAR OS Suite
Adaptive Flash Cache
System Tuner
Thin Conversion
Thin Copy Reclamation
Thin Persistence
Thin Provisioning (10240000G)
VSS Provider for Microsoft Windows
License features enabled on a trial basis that have expired:
Peer Motion Expired on June 18, 2015
If the enabled features are not correct, take note of this and correct
the issue after the out of the box script finishes.
Press enter to continue.
Support
for the CIM-based management API is disabled by default. It can be
enabled at this point.
Does the customer want this feature to be enabled (y/n)? ==> n
Saving backup copy of eventlog as event.txt --> /common/ on node1
Determining most recent copy of /common/pr_ide/biosm*
Copying node0:/common/pr_ide/biosmsg* --> node1:/common//biosmsg*
Creating default cpgs
Checking for drive table upgrade packages
Creating default AO Config
Checking for drive table upgrade packages
Not enough CPGs to create default AO CFG.
Issues were found by checkhealth:
Component ----------------Description---------------- Qty
Alert New alerts 2
Cage Degraded or failed cage power supplies 2
Cage Degraded or failed cage AC power 1
License Licenses which have expired 1
Network Too few working admin network connections 1
Node Power supplies which are failed or degraded 4
Node Power supplies with failed or degraded AC 2
Node Power supplies with failed or degraded DC 2
One or more alerts were generated that were not expected:
Id : 5
State : New
Message Code: 0x02b00de
Time : 2015-08-17 11:50:40 CST
Severity : Degraded
Type : Component state change
Message : Cage 0, Power Supply 0 Degraded (Power Supply Warning {0x403})
Id : 6
State : New
Message Code: 0x02b00fa
Time : 2015-08-17 11:50:40 CST
Severity : Major
Type : Component state change
Message : Cage 0, Power Supply 1 Failed (Power Supply Failed {0x402})
2 alerts
These alerts may indicate issues with the system; please see the Messages and
Operator's Guide for details on the meaning of individual alerts.
Out-Of-The-Box has completed.
Please continue with the SP moment of birth.
Exiting Out-Of-The-Box Experience...
3PAR Console Menu 1627110-0 3.2.1.46
1. Out Of The Box Procedure
2. Re-enter network configuration
3. Update the CBIOS
4. Enable or disable CLI error injections
5. Perform a Node-to-Node rescue
6. Set up the system to wipe and rerun ootb
7. Cancel a wipe
8. Perform a deinstallation
9. Update the system for recently added hardware (admithw)
10. Check system health (checkhealth)
11. Exit