STM8的SPI口写的NRF24L01程序
//========================================
// PROJECT: nrf24l01调试程序 发射
// AUTHOR: MENGJICHENG
// MODULE: main.c
// COMPILER: STM8 Cosmic C Compiler
// DATE: 2010-9-12 16:41
//=========================================
#include "STM8S103F.h" //Registers and memory
#define u8 unsigned char
#define u16 unsigned int
#define u32 unsigned int
//-----------------------------------
_Bool f_250us=0;
_Bool power_pin @PB_ODR:5;
_Bool key1_pin @PC_IDR:4;
_Bool key2_pin @PD_IDR:5;
_Bool IRQ_PIN @PD_IDR:3; //为低表示:1已接收到数据,数据移完时自动变为高,2发送完变低，3从发送次数超过设定值
_Bool CSN_PIN @PA_ODR:3; //为低时激活SPI发送数据，此时可设置24L01
_Bool CE_PIN @PD_ODR:4; //低时系统进入待机模式I,为高时启动发射,要保持10US
_Bool SPE @SPI_CR1:6;
_Bool MSTR @SPI_CR1:2;
_Bool TXE @SPI_SR:1;
_Bool RXNE @SPI_SR:0;
// SPI(nRF24L01) registers(addresses)
#define CONFIG 0x00 //;'Config' register address
#define EN_AA 0x01 //;'Enable Auto Acknowledgment' register address
#define EN_RXADDR 0x02 // 'Enabled RXaddresses' register address
#define SETUP_AW 0x03 // 'Setup address width' register address
#define SETUP_RETR 0x04 // 'Setup Auto. Retrans' register address
#define RF_CH 0x05 // 'RF channel' register address
#define RF_SETUP 0x06 // 'RF setup' register address
#define STATUS 0x07 // 'Status' register address
#define OBSERVE_TX 0x08 // 'Observe TX' register address
#define CD 0x09 // 'Carrier Detect' register address
#define RX_ADDR_P0 0x0A // 'RX address pipe0' register address
#define RX_ADDR_P1 0x0b // 'RXaddress pipe1' register address
#define RX_ADDR_P2 0x0c // 'RXaddress pipe2' register address
#define RX_ADDR_P3 0x0d // 'RX address pipe3' register address
#define RX_ADDR_P4 0x0e // 'RX address pipe4' register address
#define RX_ADDR_P5 0x0f // 'RX address pipe5' register address
#define TX_ADDR 0x10 // 'TX address' register address
#define RX_PW_P0 0x11 // 'RX payload width, pipe0' register address
#define RX_PW_P1 0x12 // 'RX payload width, pipe1' register address
#define RX_PW_P2 0x13 // 'RX payload width, pipe2' register address
#define RX_PW_P3 0x14 // 'RX payload width, pipe3' register address
#define RX_PW_P4 0x15 // 'RX payload width, pipe4' register address
#define RX_PW_P5 0x16 // 'RX payload width, pipe5' register address
#define FIFO_STATUS 0x17 // 'FIFO Status Register' register address
//nRF24L01 SPI Command constant 写命令时要CSN_PIN要为低
#define READ_REG 0x00 //read command to register
#define WRITE_REG 0x20 //write command to register
#define R_RX_PAYLOAD 0x61 //RX payload register address
#define W_TX_PAYLOAD 0xa0 //TX payload register address
#define FLUSH_TX 0xe1 //flush TX register command
#define FLUSH_RX 0xe2 //flush RX register command
#define R
EUSE_TX_PL 0xE3 //reuse TX payload register command
#define NOP 0xFF //No Operation, might be used to read status register
#define PAYLOAD_WIDTH 32 //发射与接收的数据个数,最高不超过32字节32*8=256
const u8 TX_ADDRESS[5]={0x12,0x34,0x56,0x78,0x9a};//默认接收通道0地址码为e7 e7 e7 e7 e7,发射地址码e7 e7 e7 e7 e7,先写低字节9a 78
u8 TX_BUF[PAYLOAD_WIDTH]={0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31};
/////////////////////////////////////////////
//
/////////////////////////////////////////////
delay_time(u16 i)
{ u16 j;
for(j=0;j
{ IWDG_KR=0Xaa; //清除看门狗
}
f_250us=0;
}
}
////////////////////////////////////////////////
//
/////////////////////////////////////
void initial_data(void)
{ u16 i;
_asm("sim"); //Disable interrupts
//Configure HSI prescaler
CLK_CKDIVR &= ~0x10; //HSIDIV[4:3]=00 [系统分频1.2.4.8],上电默认值8分频
//8mhz=16mhz/系统2分频
//Configure CPU clock prescaler
CLK_CKDIVR |= 0x00; //CPUDIV[2:0]=000: fCPU=fMASTER/[1.2.4.8.16.32.64.128]
//决定指令速度,不影响定时器
//time---------------------------
/* //TIM2 CC2 control LED Brightness
TIM2_CCMR2 |= 0x70; //Output mode PWM2.
TIM2_CCE_PINR1 |= 0x30; //CC polarity low,enable PWM output
TIM2_ARRH = 0x00; //自动从装载寄存器/定时初值,
TIM2_ARRL = 0xff; //先装高字节
TIM2_CCR2H = 0X00; //决定PWM的占空比/utycycle control register: CCR是16BIT
TIM2_CCR2L = 0X00;
TIM2_PSCR = 0x00; //BIT[2:0] Configure TIM2 prescaler =1
TIM2_CR1 |= 0x81; //ARPE - - - OPM URS UDIS CE_PINN
//------------------------------//
// TIM3 CC1 control LED Blinking
TIM3_CCMR1 |= 0x78; //Output mode PWM2.
TIM3_CCE_PINR1 |= 0x03; //CC polarity low,enable PWM output
TIM3_ARRH = 0x03;
TIM3_ARRL = 0xff; //自动从装载寄存器,先装高字节
TIM3_CCR1H = 0x02; //决定PWM的占空比/Dutycycle control register: CCR
TIM3_CCR1L = 0x00;
TIM3_PSCR |= 0x0d; //Configure TIM3 prescaler = 8192
TIM3_CR1 |= 0x81; //*/
//------------------------------//
TIM4_PSCR = 0x03; //PSC[2:0] [1.2.4.8.16.32.64.128]
TIM4_ARR = 0xfA; //定时器初值*定时器分频*系统分频/16MHZ=定时时间
//250*8*2/16mhz=250us
TIM4_IER |= 0x01; //- - - - - - - UIE(Enable TIM4 OVR interrupt)
TIM4_CR1 |= 0x81; //ARPE - - - OPM URS UDIS CE_PINN
//i/o----------------------------
PA_DDR = 0b00001000; //1=Output.
PA_CR1 = 0B11111111; //需入时1=PushPull 输出时1=推挽输出
PA_CR2 = 0b00000000;
PA_ODR = 0b00001000;
PB_DDR = 0b00100000;
PB_CR1 = 0b11111111;
PB_CR2 = 0b00000000;
PB_ODR = 0b00100000;
PC_DDR = 0b01110000;
PC_C
R1 = 0B11111111;
PC_CR2 = 0b01100000;//10mhz
PC_ODR = 0b00000000;
PD_DDR = 0b00010000;
PD_CR1 = 0b11111111;
PD_CR2 = 0b00000000; //
PD_ODR = 0b00000000;
// SPI_DeInit(void)
SPE =0;
SPI_CR1 = 0b00000000;
SPI_CR2 = 0b00000011;
SPI_ICR = 0b00000000;
SPI_SR = 0b00000000; //发射缓冲空
SPI_CRCPR = 0X07;
MSTR =1; //主设备,并开启SPI
SPE =1;
_asm("rim");
}
//////////////////////////////////////
u8 SPI_RW(u8 Data)
{
while(!TXE); // Wait until the transmit buffer is empty
SPI_DR = Data; // Send the byte
while(!RXNE); // Wait to receive a byte
Data = SPI_DR;
return(Data);
}
/*寄存器访问函数：用来设置24L01 的寄存器的值。基本思路就是通过WRITE_REG 命令（也
就是0x20+寄存器地址）把要设定的值写到相应的寄存器地址里面去，并读取返回值。对于
函数来说也就是把value 值写到reg 寄存器中。
需要注意的是，访问NRF24L01 之前首先要enable 芯片（CSN_PIN=0；），访问完了以后再disable
芯片（CSN_PIN=1；）。*/
u8 SPI_RW_Reg(u8 reg, u8 value)
{ u8 status;
CSN_PIN = 0; // CSN_PIN low, init SPI transaction
status =SPI_RW(reg); // select register
SPI_RW(value); // ..and write value to it..
CSN_PIN = 1; // CSN_PIN high again
return(status); // return nRF24L01 status byte
}
/*接收缓冲区访问函数：主要用来在接收时读取FIFO 缓冲区中的值。基本思路就是通过
READ_REG 命令把数据从接收FIFO（RD_RX_PLOAD）中读出并存到数组里面去*/
u8 SPI_Read_Buf(u8 reg, u8 *pBuf, u8 bytes)
{ u8 status,byte_ctr;
CSN_PIN = 0; // Set CSN_PIN low, init SPI tranaction
status = SPI_RW(reg); // Select register to write to and read status byte
for(byte_ctr=0;byte_ctr
CSN_PIN = 1; // Set CSN_PIN high again
return(status); // return nRF24L01 status byte
}
/*发射缓冲区访问函数：主要用来把数组里的数放到发射FIFO 缓冲区中。基本思路就是通过
WRITE_REG 命令把数据存到发射FIFO（WR_TX_PLOAD）中去。*/
u8 SPI_Write_Buf(u8 reg, u8 *pBuf, u8 bytes)
{ u8 status,byte_ctr;
CSN_PIN = 0; // Set CSN_PIN low, init SPI tranaction
status = SPI_RW(reg); //写命令字 and read status byte
for(byte_ctr=0; byte_ctr
CSN_PIN = 1; // Set CSN_PIN high again
return(status); // return nRF24L01 status byte
}
/*设定24L01 为发送方式，配置过程详见3.1 Tx 模式初始化过程。*/
void TX_Mode(void)
{ CE_PIN=0; //为低时才可设置24L01,此时处于待机模式1
// SPI_RW_Reg(WRITE_REG+SETUP_AW,0x00000011);//默认地址宽度为5字节,要与接收地址宽度
一致
SPI_Write_Buf(WRITE_REG+TX_ADDR,TX_ADDRESS,5);//发射不需要选择通道，只有一个发射通道，而接收有6个通道
SPI_Write_Buf(WRITE_REG+RX_ADDR_P0,TX_ADDRESS,5);/*P0通道用于应答,地址必须与发送的节点地址一致,地址宽度可设定,默认为5字节,如没开应答可不用写*/
SPI_RW_Reg(WRITE_REG+EN_AA,0b00000001); //Enable Auto.Ack:Pipe0
SPI_RW_Reg(WRITE_REG+EN_RXADDR,0b00000001); //Enable Pipe0作为发射时还要开启0接收吗?可能是作为应答的接收
SPI_RW_Reg(WRITE_REG+SETUP_RETR,0b00000011); //250us+86us, 3 retrans只有发射要设定
SPI_RW_Reg(WRITE_REG+RF_CH,40); //通道频率(共128频率),要与发射一致
SPI_RW_Reg(WRITE_REG+RF_SETUP,0b00000111); //TX_PWR:0dBm, Datarate:2Mbps,LNA_HCURR
SPI_RW_Reg(WRITE_REG+CONFIG,0b00001110); //上电 CRC 2bytes TX_DS允许,MAX_RT禁止
CE_PIN=1;
}
//////////////////////////////////////
void rf_power_down()
{
CE_PIN=0; //系统进入待机模式I
SPI_RW_Reg(WRITE_REG+CONFIG,0b01011000);//CRC=1(1byte),Power down,PTX
}
//////////////////////////////////////////////
void rf_power_up(void) //开启24L01
{
CE_PIN=0; //系统进入待机模式I
SPI_RW_Reg(WRITE_REG+CONFIG,0b01011010); //CRC=1(1byte),Power up,PTX
delay_time(8); //2ms 置少保持1.5ms
}
//////////////////////////////////////
//
//////////////////////////////////////
void key_scannal(void)
{ static u16 key_delay=0xffff;
static _Bool f_release ;
u16 i;
if(!key2_pin)
goto key_in;
key_delay=200; //100ms
f_release=0;
return;
key_in:
if(f_release)
return;
if(!(--key_delay==0))
return;
f_release=1;
key_delay=200; //100ms
if(key2_pin)
return;
if(!IRQ_PIN) //为低时中断
{ CSN_PIN = 0;
i = SPI_RW(NOP); // 返回状态寄存器
CSN_PIN = 1;
if(i&0b00010000)//MAX_RT判断是否因为从发次数溢出而中断
_asm("nop");
SPI_RW_Reg(WRITE_REG+STATUS,0B01110000);//要用软件写1后才能清除IRQ_PIN为高电平
}
SPI_Write_Buf(W_TX_PAYLOAD, TX_BUF, PAYLOAD_WIDTH); //Writes data to TX payload,最多只能发射32字节
CE_PIN = 1; //CE置少要保持10US高电平
i=0x0A;
while(--i);
CE_PIN = 0;
PB_ODR ^= 0b00100000;
}
//////////////////////////////////////
//
/////////////////////////////////////
void main ( void )
{ u16 i;
u8 j;
initial_data();
CE_PIN=0; // chip enable
CSN_PIN=1; // Spi disable
delay_time(400); //wait 0.1 second
TX_Mode();
delay_time(400); //wait 0.1 second
//------------------------------------
while ( 1 )
{ if(f_250us)
{ f_250us=0;
key_scannal();
++i;
if(i>0xf00)
{ i=0;
if(!IRQ_PIN) //为低时中断
{ CSN_PIN = 0;
i = SPI_RW(NOP); // 返回状态寄存器
CSN_PIN = 1;
if(i&0b00010000)//MAX_RT判断是否因为从发次数溢出而中断
PB_ODR ^= 0b00100000;
SPI_RW_Reg(WRITE_REG+STATUS,0B01110000);//要用软
件写1后才能清除IRQ_PIN为高电平
}
SPI_Write_Buf(W_TX_PAYLOAD, TX_BUF, PAYLOAD_WIDTH); //Writes data to TX payload,最多只能发射32字节
CE_PIN = 1; //CE置少要保持10US高电平
j=0x0A;
while(--j);
CE_PIN = 0;
}
}
}
}
//========================================
// PROJECT: nrf24l01调试程序 接收
// AUTHOR: MENGJICHENG
// MODULE: main.c
// COMPILER: STM8 Cosmic C Compiler
// DATE: 2010-9-12 16:41
//=========================================
#include "STM8S103F.h" //Registers and memory
#define u8 unsigned char
#define u16 unsigned int
#define u32 unsigned int
//-----------------------------------
_Bool f_250us=0;
//////////////////////////////////////////
//NRF24L01脚定义
_Bool IRQ_PIN @PD_IDR:3; //为低表示:1已接收到数据,2发送完变低，3从发送次数超过设定值
_Bool CSN_PIN @PA_ODR:3; //为低时激活SPI发送数据，此时可设置24L01
_Bool CE_PIN @PD_ODR:4; //低时系统进入待机模式I,为高时启动发射,要保持10US
_Bool SPE @SPI_CR1:6;
_Bool MSTR @SPI_CR1:2;
_Bool TXE @SPI_SR:1;
_Bool RXNE @SPI_SR:0;
// SPI(nRF24L01) registers(addresses)
#define CONFIG 0x00 //;'Config' register address
#define EN_AA 0x01 //;'Enable Auto Acknowledgment' register address
#define EN_RXADDR 0x02 // 'Enabled RXaddresses' register address
#define SETUP_AW 0x03 // 'Setup address width' register address
#define SETUP_RETR 0x04 // 'Setup Auto. Retrans' register address
#define RF_CH 0x05 // 'RF channel' register address
#define RF_SETUP 0x06 // 'RF setup' register address
#define STATUS 0x07 // 'Status' register address
#define OBSERVE_TX 0x08 // 'Observe TX' register address
#define CD 0x09 // 'Carrier Detect' register address
#define RX_ADDR_P0 0x0A // 'RX address pipe0' register address
#define RX_ADDR_P1 0x0b // 'RXaddress pipe1' register address
#define RX_ADDR_P2 0x0c // 'RXaddress pipe2' register address
#define RX_ADDR_P3 0x0d // 'RX address pipe3' register address
#define RX_ADDR_P4 0x0e // 'RX address pipe4' register address
#define RX_ADDR_P5 0x0f // 'RX address pipe5' register address
#define TX_ADDR 0x10 // 'TX address' register address
#define RX_PW_P0 0x11 // 'RX payload width, pipe0' register address
#define RX_PW_P1 0x12 // 'RX payload width, pipe1' register address
#define RX_PW_P2 0x13 // 'RX payload width, pipe2' register address
#define RX_PW_P3 0x14 // 'RX payload width, pipe3' register address
#define RX_PW_P4 0x15 // 'RX payload width, pipe4' register address
#define RX_PW_P5 0x16 // 'RX payload width, pipe5' register address
#define FIFO_STATUS 0x17 // 'FIFO Status Register' register address
//nRF24L01 SPI Command constant
#define READ_REG 0x00 //read command to register
#define WRITE_REG 0x20 //write command to register
#define R_RX_PAYLOAD
0x61 //RX payload register address
#define W_TX_PAYLOAD 0xa0 //TX payload register address
#define FLUSH_TX 0xe1 //flush TX register command
#define FLUSH_RX 0xe2 //flush RX register command
#define REUSE_TX_PL 0xE3 //reuse TX payload register command
#define NOP 0xFF //No Operation, might be used to read status register
#define PAYLOAD_WIDTH 32 //发射与接收的数据个数,最高不超过32字节32*8=256
const u8 RX_ADDRESS[5]={0x12,0x34,0x56,0x78,0x9a};
u8 RX_BUF[PAYLOAD_WIDTH];
/////////////////////////////////////////////
//
/////////////////////////////////////////////
delay_time(u16 i)
{ u16 j;
for(j=0;j
{
IWDG_KR=0Xaa; //清除看门狗
}
f_250us=0;
}
}
////////////////////////////////////////////////
//
/////////////////////////////////////
void initial_data(void)
{ u16 i;
_asm("sim"); //Disable interrupts
//Configure HSI prescaler
CLK_CKDIVR &= ~0x10; //HSIDIV[4:3]=00 [系统分频1.2.4.8],上电默认值8分频
//8mhz=16mhz/系统2分频
//Configure CPU clock prescaler
CLK_CKDIVR |= 0x00; //CPUDIV[2:0]=000: fCPU=fMASTER/[1.2.4.8.16.32.64.128]
//决定指令速度,不影响定时器
//time---------------------------
/* //TIM2 CC2 control LED Brightness
TIM2_CCMR2 |= 0x70; //Output mode PWM2.
TIM2_CCE_PINR1 |= 0x30; //CC polarity low,enable PWM output
TIM2_ARRH = 0x00; //自动从装载寄存器/定时初值,
TIM2_ARRL = 0xff; //先装高字节
TIM2_CCR2H = 0X00; //决定PWM的占空比/utycycle control register: CCR是16BIT
TIM2_CCR2L = 0X00;
TIM2_PSCR = 0x00; //BIT[2:0] Configure TIM2 prescaler =1
TIM2_CR1 |= 0x81; //ARPE - - - OPM URS UDIS CE_PINN
//------------------------------//
// TIM3 CC1 control LED Blinking
TIM3_CCMR1 |= 0x78; //Output mode PWM2.
TIM3_CCE_PINR1 |= 0x03; //CC polarity low,enable PWM output
TIM3_ARRH = 0x03;
TIM3_ARRL = 0xff; //自动从装载寄存器,先装高字节
TIM3_CCR1H = 0x02; //决定PWM的占空比/Dutycycle control register: CCR
TIM3_CCR1L = 0x00;
TIM3_PSCR |= 0x0d; //Configure TIM3 prescaler = 8192
TIM3_CR1 |= 0x81; //*/
//------------------------------//
TIM4_PSCR = 0x03; //PSC[2:0] [1.2.4.8.16.32.64.128]
TIM4_ARR = 0xfA; //定时器初值*定时器分频*系统分频/16MHZ=定时时间
//250*8*2/16mhz=250us
TIM4_IER |= 0x01; //- - - - - - - UIE(Enable TIM4 OVR interrupt)
TIM4_CR1 |= 0x81; //ARPE - - - OPM URS UDIS CE_PINN
//i/o----------------------------
PA_DDR = 0b00001000; //1=Output.
PA_CR1 = 0B11111111; //需入时1=PushPull 输出时1=推挽输出
PA_CR2 = 0b00000000;
PA_ODR = 0b00001000;
PB_DDR = 0b00100000;
PB_CR1 = 0b11111111;
PB_CR2 = 0b00000000;
PB_ODR = 0b00100000;
PC
_DDR = 0b01110000;
PC_CR1 = 0B11111111;
PC_CR2 = 0b01100000;//10mhz
PC_ODR = 0b00000000;
PD_DDR = 0b00010000;
PD_CR1 = 0b11111111;
PD_CR2 = 0b00000000; //
PD_ODR = 0b00000000;
// SPI_DeInit(void)
SPE =0;
SPI_CR1 = 0b00000000;
SPI_CR2 = 0b00000011;
SPI_ICR = 0b00000000;
SPI_SR = 0b00000000; //发射缓冲空
SPI_CRCPR = 0X07;
MSTR =1; //主设备,并开启SPI
SPE =1;
_asm("rim");
}
//////////////////////////////////////
u8 SPI_RW(u8 Data)
{
while(!TXE); /* Wait until the transmit buffer is empty */
SPI_DR = Data; /* Send the byte */
while(!RXNE); /* Wait to receive a byte*/
Data = SPI_DR;
return(Data);
}
/*寄存器访问函数：用来设置24L01 的寄存器的值。基本思路就是通过WRITE_REG 命令（也
就是0x20+寄存器地址）把要设定的值写到相应的寄存器地址里面去，并读取返回值。对于
函数来说也就是把value 值写到reg 寄存器中。
需要注意的是，访问NRF24L01 之前首先要enable 芯片（CSN_PIN=0；），访问完了以后再disable
芯片（CSN_PIN=1；）。*/
u8 SPI_RW_Reg(u8 reg, u8 value)
{ u8 status;
CSN_PIN = 0; // CSN_PIN low, init SPI transaction
status = SPI_RW(reg); // select register
SPI_RW(value); // ..and write value to it..
CSN_PIN = 1; // CSN_PIN high again
return(status); // return nRF24L01 status byte
}
/*接收缓冲区访问函数：主要用来在接收时读取FIFO 缓冲区中的值。基本思路就是通过
READ_REG 命令把数据从接收FIFO（RD_RX_PLOAD）中读出并存到数组里面去*/
u8 SPI_Read_Buf(u8 reg, u8 *pBuf, u8 bytes)
{ u8 status,byte_ctr;
CSN_PIN = 0; // Set CSN_PIN low, init SPI tranaction
status = SPI_RW(reg); // Select register to write to and read status byte
for(byte_ctr=0;byte_ctr
CSN_PIN = 1; // Set CSN_PIN high again
return(status); // return nRF24L01 status byte
}
/*发射缓冲区访问函数：主要用来把数组里的数放到发射FIFO 缓冲区中。基本思路就是通过
WRITE_REG 命令把数据存到发射FIFO（WR_TX_PLOAD）中去。*/
u8 SPI_Write_Buf(u8 reg,u8 *pBuf,u8 bytes)
{ u8 status,byte_ctr;
CSN_PIN = 0; // Set CSN_PIN low, init SPI tranaction
status = SPI_RW(reg); //写命令字 and read status byte
for(byte_ctr=0;byte_ctr
CSN_PIN = 1; // Set CSN_PIN high again
return(status); // return nRF24L01 status byte
}
/*设定24L01 为接收方式，配置过程详见3.2 Rx 模式初始化过程。*/
void RX_Mode(void)
{ CE_PIN=0; //为低时才可设置24L01，此时处于待机模式1
// SPI_RW_Reg(WRITE_REG+SETUP_AW,0b00000011); //默认地址宽度为5字
节,要与发送地址宽度一致
SPI_Write_Buf(WRITE_REG+RX_ADDR_P0,RX_ADDRESS,5);//选择接收通道0和地址号
SPI_RW_Reg(WRITE_REG+EN_AA,0b00000001); // Enable Auto.Ack:Pipe0
SPI_RW_Reg(WRITE_REG+EN_RXADDR,0b00000001); // Enable Pipe0
SPI_RW_Reg(WRITE_REG+RF_CH,40); //通道频率(共128频率),要与发射一致
SPI_RW_Reg(WRITE_REG+RX_PW_P0,PAYLOAD_WIDTH);//设定接收多少个字节,最多一帧只能接收32字节,与发射一样
SPI_RW_Reg(WRITE_REG+RF_SETUP,0b00000111); //TX_PWR:0dBm, Datarate:2Mbps,LNA_HCURR
SPI_RW_Reg(WRITE_REG+CONFIG,0b00001111); // 上电,CRC 2 bytes & RX_DR enabled..
CE_PIN = 1;
}
/////////////////////////////////////////////
void rf_power_down()
{
CE_PIN=0; //系统进入待机模式I
SPI_RW_Reg(WRITE_REG+CONFIG,0b01011000);//CRC=1(1byte),Power down,PTX
}
//////////////////////////////////////////////
void rf_power_up(void) //开启24L01
{
CE_PIN=0; //系统进入待机模式I
SPI_RW_Reg(WRITE_REG+CONFIG,0b01011010); //CRC=1(1byte),Power up,PTX
delay_time(8); //2ms 置少保持1.5ms
}
//////////////////////////////////////
//
/////////////////////////////////////
void main ( void )
{
u16 i; u8 z;
initial_data();
CE_PIN=0; // chip enable
CSN_PIN=1; // Spi disable
delay_time(400); //wait 0.1 second
RX_Mode();
delay_time(400); //wait 0.1 second
//------------------------------------
while ( 1 )
{ if(f_250us)
{
f_250us=0;
if(IRQ_PIN) //为高时
continue;
SPI_Read_Buf(R_RX_PAYLOAD,RX_BUF,PAYLOAD_WIDTH);
SPI_RW_Reg(WRITE_REG+STATUS,0B01110000); //要用软件写1后才能清除IRQ_PIN
if(!RX_BUF[0]==0)
goto main_loop;
if(!RX_BUF[1]==1)
goto main_loop;
if(!RX_BUF[2]==2)
goto main_loop;
if(!RX_BUF[3]==3)
goto main_loop;
if(!RX_BUF[4]==4)
goto main_loop;
if(!RX_BUF[5]==5)
goto main_loop;
if(!RX_BUF[6]==6)
goto main_loop;
if(!RX_BUF[7]==7)
goto main_loop;
if(!RX_BUF[8]==8)
goto main_loop;
if(!RX_BUF[9]==9)
goto main_loop;
if(!RX_BUF[10]==10)
goto main_loop;
if(!RX_BUF[11]==11)
goto main_loop;
if(!RX_BUF[12]==12)
goto main_loop;
if(!RX_BUF[13]==13)
goto main_loop;
if(!RX_BUF[14]==14)
goto main_loop;
if(!RX_BUF[15]==15)
goto main_loop;
if(!RX_BUF[16]==16)
goto main_loop;
if(!RX_BUF[17]==17)
goto main_loop;
if(!RX_BUF[18]==18)
goto main_loop;
if(!RX_BUF[19]==19)
goto main_loop;
if(!RX_BUF[20]==20)
goto main_loop;
if(!RX_BUF[21]==21)
goto main_loop;
if(!RX_BUF[22]==22)
goto main_loop;
if(!RX_BUF[23]==23)
goto main_loop;
if(!RX_BUF[24]==24)
goto main_loop;
if(!RX_BUF[25]==25)
goto main_loop;
if(!RX_BUF[26]==26)
goto main_loop;
if(!RX_BUF[27]==27)
goto main_loop;
if(!RX_BUF[28]==28)
goto main_loop;
if(!RX_BUF[29]==29)
goto m
ain_loop;
if(!RX_BUF[30]==30)
goto main_loop;
if(!RX_BUF[31]==31)
goto main_loop;
RX_BUF[0]==0;
RX_BUF[1]==0;
RX_BUF[2]==0;
RX_BUF[3]==0;
RX_BUF[4]==0;
RX_BUF[5]==0;
RX_BUF[6]==0;
RX_BUF[7]==0;
RX_BUF[8]==0;
RX_BUF[9]==0;
RX_BUF[10]==0;
RX_BUF[11]==0;
RX_BUF[12]==0;
RX_BUF[13]==0;
RX_BUF[14]==0;
RX_BUF[15]==0;
RX_BUF[16]==0;
RX_BUF[17]==0;
RX_BUF[18]==0;
RX_BUF[19]==0;
RX_BUF[20]==0;
RX_BUF[21]==0;
RX_BUF[22]==0;
RX_BUF[23]==0;
RX_BUF[24]==0;
RX_BUF[25]==0;
RX_BUF[26]==0;
RX_BUF[27]==0;
RX_BUF[28]==0;
RX_BUF[29]==0;
RX_BUF[30]==0;
RX_BUF[31]==0;
PB_ODR ^= 0b00100000;
main_loop:
_asm("nop");
}
}
}
- NRF24L01无线模块C语言程序
- nrf24l01无线模块NRF24L01模块收发c程序
- NRF24L01收发程序
- NRF24L01无线发送程序(调试成功)
- NRF24L01功能使用文档
- nrf24L01工作流程图型
- NRF24L01无线模块收发程序(实测成功 多图)
- NRF24L01无线发射简易教程
- STC12单片机SPI的nrf24l01接收程序
- nRF24L01无线通信系统设计
- NRF24L01无线模块程序
- nRF24L01 的无线温湿度检测系统电路及软件设计
- nRF24L01的近距离无线数据传输
- NRF24L01详细教程..
- nrf24L01发送接收流程图
- stc12单片机SPI的nrf24l01程序
- NRF24L01的发送与接收程序
- nRF24L01调试办法
- nRF24l01无线模块 接收端程序for 51单片机
- NRF24L01 MSP430发送接收程序