故障码英文)
老车故障码
D701,Immobilizer:ECU-BCM Communication Line Data Error 1,钥匙防盗系统:ECU-BCM 通信线路数据错误1 D702,Immobilizer:ECU-BCM Communication Line Data Error 2,钥匙防盗系统:ECU-BCM 通信线路数据错误2 D704,Immobilizer:ECU-BCM Communication Line Data Error 3,钥匙防盗系统:ECU-BCM 通信线路数据错误3 D708,Immobilizer:No ECM Request,钥匙防盗系统:无ECM 请求
D901,Immobilizer:Immobilizer Power Short to Ground,钥匙防盗系统:钥匙防盗系统电源与搭铁电路短路
D902,Immobilizer:Immobilizer Power Short to Battery,钥匙防盗系统:钥匙防盗系统电源与蓄电池短路
D904,Immobilizer:Immobilizer Output Signal Open/Short(Ground),钥匙防盗系统:钥匙防盗系统输出信号断路/短路(搭铁)
D908,Immobilizer:Immobilizer Output Signal Short to Battery.,钥匙防盗系统:钥匙防盗系统输出信号与蓄电池短路.
D910,Immobilizer:Immobilizer Input Signal Open/Short(Ground),钥匙防盗系统:钥匙防盗系统输入信号断路/短路(搭铁)
D920,Immobilizer:Immobilizer Input Signal Short to Battery.,钥匙防盗系统:钥匙防盗系统输入信号与蓄电池短路.
D940,Immobilizer:Immobilizer Antenna Coil Malfunction,钥匙防盗系统:钥匙防盗系统天线线圈故障
P32,Ignition Output(Battery Short),点火开关输出(蓄电池短路)
P32-1,Ignition Output(OC/SC Ground),点火开关输出(OC/SC搭铁)
P33,Idle Speed Control Adaption,怠速控制适应
P34,Idle Speed Control Actuator Short to Battery,怠速控制执行器与蓄电池短路
P34-1,Idle Speed Control Actuator Open / Short to Ground,怠速控制执行器断路/ 与搭铁电路短路
P46,A/C Relay Short to Battery,空调继电器与蓄电池短路
P46-1,A/C Relay Open or Short to Ground,空调继电器电路与搭铁电路断路或短路
P67,Cooling Fan Relay Short to Battery,冷却风扇继电器与蓄电池短路
P67-1,Cooling Fan Relay Open or Short to Ground,冷却风扇继电器断路或与搭铁短路
P86,No Answer From VIM (Line Open),VIM无应答(电路断路)
P86-1,VIM Error Answer (Mismatching),VIM故障应答(不匹配)
PXX,Potentionmeter,电位计
PXX-1,A/F Ratio Correction,A/F 比(空燃比)校正
PXX-2,Engine Coolant Temperature Signal Circuit Short to Battery,发动机冷却水温信号电路与蓄电池短路
PXX-3,Engine Coolant Temperature Signal Circuit Open/Short to Ground,发动机冷却水温信号电路断路/与搭铁电路短路
E5,CAS Reference Mark,CAS 参考标记
M33,ISC Valve,ISC 阀
MXX,Engine Coolant Temperature Signal(A/T),发动机冷却水温度信号(A/T)
XX,Timing Overflow,正时过大
XX-1,Illegal Interrupt,非法中断
XX-10,Accelerometer Bias,加速表偏离
XX-11,Accelerometer Continuity,加速表连续
XX-2,Watchdog Failure,监测器故障
XX-3,A/D Error,A/D 故障
XX-4,Parameter Xsum Fail,参数Xsum 错误
XX-5,Threshold Xsum Fail,界限Xsum 故障
XX-6,Threshold Load Fail,界限负荷故障
XX-7,Accelerometer 1st St.,加速表1st St.
XX-8,Accelerometer Rail,加速杆
XX-9,Accelerometer Temp,加速表温度
00,Crash Data Stored,碰撞数据储存
00-1,Crash Data Stored(Int),碰撞数据储存(Int)
00-2,Crash Data Stored H,碰撞数据储存H
00-3,Crash Occurred,碰撞产生
0001,Power Seat ECU Malfunction,电动座椅ECU 故障
0002,Power Seat Slide Motor Malfunction,电动座椅滑动电机故障
0003,Power Seat Front Height Motor-Malfunction,电动座椅前高度电机-故障
0004,Power Seat Right Rear Height Motor-Malfunction,电动座椅右后高度电机-故障
0005,Power Seat Recline Motor-Malfunction,电动座椅倾斜电机-故障
0006,Power Tilt ECU-Malfunction,动力倾斜ECU-故障
0007,Steering Tilt Motor-Malfunction,转向倾斜电机-故障
0008,Steering Tilt Position Sensor,转向倾斜位置传感器
001-1,TCCU Module,TCCU 块
0010,Steering Telescopic Motor-Malfunction,转向伸缩式电机-故障
0011,Telescopic Sensor-Malfunction,伸缩传感器-故障
0011-1,Hard/Soft Valve,硬/软阀
0012,Keyless Entry Communication Malfunction,遥控器通信故障
0013,Multifunction ECU Malfunction,多功能ECU 故障
0014,ETACS-ECU Malfunction,ETACS-ECU 故障
0015,Instrument Panel-ECU Malfunction,仪表板-ECU 故障
0016,Drive Door Module(LH) Malfunction,驾驶席车门模块(LH)故障
0017,Room Mirror Motor-Malfunction,室内后视镜电机-故障
0018,Room Mirror Sensor-Malfunction,室内后视镜传感器-故障
0019,Crash Sensor Malfunction,碰撞传感器故障
01,Engine Speed(Np) Sensor,发动机速度(Np)传感器
01-08,Driver Airbag Resistance Circuit Short to Ground (1st stage) H,驾驶席安全气囊电阻电路与搭铁电路短路(1级) H
01-1,Untaught Transponder,未登录发射器
01-11,Accelerometer Error,加速表故障
01-2,Ignition System,点火系统
01-3,Transponder Communication Error,发射器通信故障
01-4,ADU Fault,ADU 故障
01-6,ADU Fault H,ADU 故障H
01-7,Driver Airbag Resistance Circuit Short to Ground (1st stage),驾驶席安全气囊电阻电路与搭铁电路短路(1级)
01-8,Actuator System,执行器系统
010-1,Shift Motor,换档电机
011-1,Magnetic S/Clutch,电磁S/离合器
02,Isolation Solenoid Circuit Open,隔离电磁阀电路断路
02-1,ECM Communication Link Malfunction,ECM 通信连接故障
02-10,Driver Airbag Resistance Circuit Short to Battery (1st stage) H,驾驶席安全气囊电阻电路与蓄电池短路(1级) H
02-11,CPU Error,CPU 故障
02-12,FCVC Request Signal Error,FCVC 请求信号故障
02-2,Crankshaft Position Sensor A Circuit,曲轴位置传感器A 电路
02-4,Distributor Ne Signal,分电器Ne 信号
02-5,Engine Speed Signal,发动机速度信号
02-6,Engine Speed(TDC) Sensor,发动机速度(TDC)传感器
02-7,Engine Speed Signal,发动机速度信号
02-9,Driver Airbag Resistance Circuit Short to Battery (1st stage),驾驶席安全气囊电阻电路与蓄电池短路(1级) 0215,1st Cylinder Detect Sensor,1st 气缸检测传感器
0216,Idle-Up Solenoid 1,快怠速电磁阀1
0217,Second Lock Solenoid Malfunction,二次锁止电磁阀故障
03,Dump Solenoid Circuit Open,清除电磁阀电路断路
03-1,Distributor G1 Signal,分电器G1 信号
03-2,ECM Communication Error,ECM 通信故障
03-3,ETACS RF Communication Error,ETACS RF 通信故障
03-4,Fuel Pump Relay,燃油泵继电器
03-5,Driver Airbag Circuit open,驾驶席安全气囊电路断路
03-6,Camshaft Position Sensor,凸轮轴位置传感器
04,Solenoid Valve Switch Close,电磁阀开关关闭
04-1,Distributor G2 Signal,分电器G2 信号
04-2,ETACS C/S Communication Error,ETACS C/S 通信故障
04-3,Immobilizer Antenna-Open,钥匙防盗系统天线-断路
04-4,Idle Speed Control Actuator (Opening Coil),怠速控制执行器(打开线圈)
04-5,Driver Airbag Circuit short,驾驶席安全气囊电路短路
04-6,IP0: Ground Leakage,IP0: 搭铁电压泄漏
04-7,Driver Squib Open,
0416,Idle-Up Solenoid 2,快怠速电磁阀2
0417,Liquid/Vapor Relay Malfunction,液气态继电器故障
05,Driver Squib Short,
05-1,IP0: V Battery Leakage,IP0: 电源电压泄漏
05-2,Knock Sensor/Control Unit,爆震传感器/控制模块
05-3,BCM Internal Fault or EEPROM,BCM 间歇故障或EEPROM
05-7,Low Side Driver Error,低侧驾驶席故障
0552,Power Steering Switch-Low Input,动力转向开关-低电压输入
06,Rear Wheel Speed Sensor. Signal Sudden Change,后轮速传感器信号突变
06-1,ECM Request Signal Error,ECM 请求信号故障
06-2,EMS not Detected,EMS 未检测到
06-7,Driver Airbag Circuit,驾驶席安全气囊电路
07,Isolation Solenoid Circuit Short,隔离电磁阀电路短路
07-1,Passenger Airbag Circuit Open,助手席安全气囊电路断路
07-4,VIN Error,VIN 错误
07-5,Passenger Airbag Circuit,助手席安全气囊电路
0704,BCM :Brake Lamp Malfunction,BCM :倒车灯故障
0704-1,Brake Lamp Malfunction,制动灯故障
0708,BCM :Brake Fuse Open,BCM :制动器保险丝断路
0708-1,Brake Fuse Open,制动保险丝断路
0710,BCM irection Lamp Malfunction,BCM :转向灯故障
0742-b,Torque Converter Clutch System B,液力变矩器离合器系统B
0763,Shift Solenoid #3 Electrical,电子式换档电磁阀#3
08,Passenger Squib Open,
08-1,Dump Solenoid Circuit Short,清除电磁阀电路短路
08-2,Passenger Airbag Circuit Short,助手席安全气囊电路短路
0816,Idle-Up Solenoid 3,快怠速电磁阀3
09,Speed Sensor Circuit Open,速度传感器电路断路
09-1,Water Temperature Sensor,水温度传感器
09-2,Passenger Squib Short,
09-3,Low Pressure Switch-Short Circuit,低压开关-电路短路
09-4,Low Pressure Switch-Short Circuit H,低压开关-电路短路H
0901,BCM :Rain Sensor Malfunction 1,BCM :雨量传感器故障1
0902,BCM :Rain Sensor Malfunction 2,BCM :雨量传感器故障2
0904,BCM :Rain Sensor Malfunction 3,BCM :雨量传感器故障3
0908,BCM :Wiper Stop Circuit Short to Battery,BCM :雨刮器停止电路与蓄电池短路0910,BCM :Wiper Stop Circuit Short to Ground,BCM :雨刮器停止电路与搭铁电路短路0A,Low Pressure Switch-Open Circuit,低压开关-电路断路
0A-1,Low Pressure Switch-Open Circuit H,低压开关-电路断路H
0B,Power Supply Ignition,电源点火开关
0B-1,Firing Circuit Short to Ground,点火电路与搭铁电路短路
0B-2,Firing Circuit Short to Ground H,点火电路与搭铁电路短路H
0B01,BCM :CAN Error,BCM :CAN故障
0B02,BCM :CAN Bus Off,BCM :CAN Bus Off
0B04,BCM ow Voltage/Lin Communication Line(Rx),BCM :低压/Lin通信线(Rx)
0B08,BCM ow Voltage/Lin Communication Line(Tx),BCM :低压/Lin通信线(Tx)
0B10,BCM :CAN Timeout between BCM & DDM,BCM :BCM & DDM之间CAN 超时
0B20,BCM :CAN Timeout between BCM & ADM,BCM :BCM & ADM之间CAN 超时
0B40,BCM :CAN Timeout between BCM & PIC,BCM :BCM & PIC之间CAN 超时
0B80,BCM :CAN Timeout between BCM & Seat,BCM : BCM & 座椅之间CAN 超时
0C,Firing Circuit Malfunction,点火电路故障
0C-1,Firing Circuit Malfunction H,点火电路故障H
0D,SRS Service Reminder Indicator,SRS 维修提示器指示灯
0D-1,SRS Service Reminder Indicator H,SRS 维修提示器指示灯H
0E-1,ECU Error H,ECU 故障H
0E-3,SRS Control Module H,SRS 控制模块H
0F,Engine Malfunction Indication Lamp,发动机故障警告灯
1,Left Front Sensor Error,左前传感器故障
1-1,Main eft Front PSW Lin Error,主:左前PSW Lin 故障
1-2,Main:Right Front WDW Lin Error,主:右前WDW电路故障
1-3,Seat Slide Motor or Sensor Error,座椅滑动电机或传感器故障
1-4,Tilt Motor or Sensor Error,倾斜电机或传感器故障
10,Air Temp Sensor,空气温度传感器
10-1,Left Front:SPW Motor Hall Sensor 1 Error,左前:SPW 电机霍尔传感器 1 故障
10-11,MFI Control Relay,MFI 控制继电器
10-2,Right Front:SPW Motor Hall Sensor 2 Error,右前:SPW 电机霍尔传感器2 故障
10-3,Low Ignition Power Supply,点火开关电源电压低
10-4,Low Ignition Power Supply(Int),点火开关电源电压低(Int)
10-5,Speed Sensor Circuit Short/Malfunction,速度传感器电路短路/故障
10-6,Injector #2,喷油嘴#2
10-7,SRSCM Parameter,SRSCM 参数
10-8,SRSCM Parameter H,SRSCM 参数H
100,Pretensioner Front-Driver Resistance Circuit Open,拉紧器前-驾驶席电阻电路断路
100-1,Speed Sensor,速度传感器
1001,Control Module or Checksum,控制模块或检测sum
1001-2,Control Module or Checksum A,控制模块或检测sum A
1002,No Start ,No Flame-Up A,不起动，不点火-Up A
1002-1,No Start ,No Flame-Up,不起动，不点火-Up
1002-2,No Start, No Flame-Up Even after Restart,不起动，不点火-重新启动后上升平稳
1003,Flame-Out During Operation with No Further Flame-Up A,工作中燃烧停止A
1003-1,Flame-Out During Operation with No Further Flame-Up,工作中燃烧停止
1006,Flame Prior to Combustion Operation A,燃烧工作前点火A
1006-1,Flame Prior to Combustion Operation,燃烧工作前点火
101,Pretensioner Front-Driver Resistance Circuit Short,拉紧器前-驾驶席电阻电路短路
101-1,Hub Solenoid Valve,轮毂电磁阀
1013,3 Times Flame-Out During Heating Cycle A,加热周期A期间3次燃烧停止
1013-1,3 Times Flame-Out During Heating Cycle,加热周期内3次燃烧停止
1016,Ignition Signal Output,点火开关信号输出
1017,A/C Cut Relay Malfunction,空调切断继电器故障
102,Pretensioner Front-Driver Resistance Circuit Short to Battery,拉紧器前-驾驶席电阻电路与蓄电池短路103,Pretensioner Front-Driver Resistance Circuit Short to Ground,拉紧器前-驾驶席电阻电路与搭铁电路短路11,Left Front:SPW Motor Hall Sensor 2 Error,左前:SPW 电机霍尔传感器 2 故障
11-11,Throttle Position Sensor-Short Circuit,节气门位置传感器-短路
11-12,Right Front:SPW Normalization Error,右前:SPW 正常故障
11-13,High Ignition Power Supply,点火开关电源供应信号过高
11-14,High Ignition Power Supply(Int),点火开关电源供应信号过高(Int)
11-16,Valve Relay Circuit Open,阀继电器电路断路
11-17,Injector #1,喷油嘴#1
11-18,Airbag Unit Specification Mismatch,安全气囊模块参数不相匹配
11-19,Power Supply Ignition H,电源点火开关H
11-2,FIS(Front Impact Sensor)-Short,FIS(前碰撞传感器)-短路
11-20,Clutch Coil,离合器线圈
11-3,Accelerator Pedal Position Sensor Malfunction,加速踏板位置传感器故障
11-4,TCS Control Module,TCS 控制模块
11-6,Transaxle Control Module-Failsafe,变速器控制模块-失效保护
11-7,Room Temperature Sensor-Open,室内温度传感器-断路
11-8,G-Sensor,G-传感器
11-9,Oxygen Sensor,氧传感器
110,Selector Switch,换档开关
12,Right Front:SPW Unit Error,右前:SPW 模块故障
12-1,Accel Sensor,加速传感器
12-13,Accessory Power Supply Fault,附加电源故障
12-14,Accessory Power Supply Fault(Intermittent),附加电源故障(间歇故障)
12-15,Insufficient Brake Fluid/Brake Pressure Low,制动液不足/制动压力低
12-16,Valve Relay Circuit Short,阀继电器电路短路
12-17,Unit Connector Assembling Incomplete,模块连接器总成不完整
12-18,Left Front:SPW Normalization Error,左前:SPW 正常故障
12-19,ABS Modulator,ABS 调制器
12-2,SCSV-A,SCSV-A
12-21,TCM-First Gear Command Fail,TCM-1档控制故障
12-23,Firing Circuit Short to Battery,点火电路与蓄电池短路
12-24,Manifold Absolute Pressure/Barometric Pressure Circuit,进气歧管绝对压力/大气压压力电路12-26,Volume Air Flow Sensor,空气流量传感器
12-3,Room Temperature Sensor-Short,室内温度传感器-短路
12-4,Knee Squib Open,
12-5,Alternator L-Terminal,交流发电机L- 端子
12-6,LH or RH Impact Sensor-Open,左/右碰撞传感器-断路
12-7,Manifold Absolute Pressure Sensor,进气歧管绝对压力传感器
1245,Air Mix Feedback Open(Low)-Driver,温度门反馈电路断路(低压)-驾驶席
1250-3,Direction Mode Feedback Short (High)-Driver,方向模式反馈电路短路(高压)-驾驶席
老车故障码13,Left Front:SPW Unit Error,左前:SPW 模块故障
13-1,Pulse Generator B-Failsafe,脉冲发生器B-失效保护
13-10,Low Pressure Switch,低压开关
13-11,Right Front:Motor Hall Sensor Count Dir.Error,右前:电机霍尔传感器反方向故障
13-12,Control Module,控制模块
13-13,Motor Relay Circuit Open,电机继电器电路断路
13-14,Power Supply(ACC),电源(ACC)
13-16,Excessive Decay,腐蚀严重
13-17,Low Speed Limit,低速限制
13-2,SCSV-B,SCSV-B
13-21,Intake Air Temperature Sensor,进气温度传感器
13-3,Throttle Position Sensor-Malfunction,节气门位置传感器-故障
13-4,Engine Speed Signal,发动机速度信号
13-5,EPS Solenoid Valve,EPS 电磁阀
13-6,Knee Squib Short,
13-8,LH and RH Impact Sensor-Open,左/右碰撞传感器-断路
13-9,In-CAR Temperature Sensor Circuit Open,室内温度传感器电路断路
14,Left Front:Motor Hall Sensor Counter Dir.Error,左前:电机霍尔传感器反方向异常
14-10,Boost Pressure Sensor Circuit Malfunction,助力器传感器电路故障
14-12,Redundant Brake,多余制动
14-14,Right Front:Motor Thermal Protection Error,右前:电机热保护故障
14-15,Motor Relay Circuit Short,电机继电器电路短路
14-16,Ignition Low,点火开关电压低
14-18,Throttle Position Sensor,节气门位置传感器
14-2,SCSV-A(Failsafe),SCSV-A(失效保护)
14-3,In-CAR Temperature Sensor Circuit Short,室内温度传感器电路短路
14-5,Throttle Position Sensor-Abnormal Adjustment,节气门位置传感器-异常调整
14-6,TCS On Switch,TCS On 开关
14-7,Steering Angle Sensor,转向角传感器
15,Left Front:Motor Thre.Protection Error,左前:电机热保护故障
15-1,HO2S (Left),氧传感器(左)
15-10,Control Switch,控制开关
15-13,Capacitor Volt Low,电容器电压低
15-2,SCSV-B(Failsafe),SCSV-B(失效保护)
15-4,Traction Control Switch,牵引力控制开关
15-6,Transmission Fluid Temperature Sensor Circuit Open,变速器液体温度传感器电路断路15-7,Right Front:Motor Holl Sensor Power Line Short,右前:电机霍尔传感器电源电路短路15-8,Wheel Speed Sensor,轮速传感器
16,Left Front:Motor Hall Sensor Power Line Short,左前:电机霍尔传感器电源电路短路
16-1,Transmission Fluid Temperature Sensor Circuit Short,变速器液体温度传感器电路短路16-12,Warning Lamp Short,警告灯短路
16-3,PCSV(Failsafe),PCSV(失效保护)
16-4,EGR Position Sensor,EGR 位置传感器
16-5,Low Ignition Voltage,点火开关电压低
16-6,Idle Speed Control Actuator (Closing Coil),怠速控制执行器(关闭线圈)
16-7,Brake Switch Circuit,制动开关电路
16-8,Power Supply System,电源系统
16-9,Cancel Signal,取消信号
1608,Dosing Pump Circuit Short to Ground A,定量泵电路与搭铁电路短路A
1608-1,Dosing Pump Circuit Short to Ground,定量泵电路与搭铁电路短路
1608-2,Dosing Pump: Short Circuit Against Ground,定量泵: 搭铁电路短路
1609,Combustion Air Fan Circuit Short to Ground A,燃烧空气风扇电路与搭铁短路A
1609-1,Combustion Air Fan Circuit Short to Ground,燃烧空气风扇电路与搭铁电路短路
160A,Glow Plug Circuit Short to Ground A,预热塞电路与搭铁电路短路A
160A-1,Glow Plug Circuit Short to Ground,预热塞电路与搭铁电路短路
160B,Water Pump:Circuit Ground A,水泵:搭铁电路A
160B-1,Water Pump:Circuit Ground,水泵:搭铁电路
160B-2,Water Pump: Short Circuit Against Ground,水泵:搭铁电路短路
160C,Vehicle Air Fan:Circuit Ground A,车辆空气风扇:搭铁电路A
160C-1,Vehicle Air Fan:Circuit Ground,车辆空气风扇:搭铁电路
160C-2,Vehicle Air Fan: Short Circuit Against Ground,车辆空气风扇: 搭铁电路短路
17,Right Front:SPW Input Voltage Low,右前:SPW 输入电压低
17-1,Feedback System,反馈系统
17-2,Feedback System(Left),反馈系统(左)
17-5,High Ignition Voltage,点火开关电压过高
17-6,TCS Switch,TCS 开关
1772,Selection Position,换档位置
1780,Push-Pull Sensor,推-拉传感器
18,Left Front:SPW Input Voltage Low,左前:SPW 输入电压低
18-1,Feedback Solenoid Valve,反馈电磁阀
18-2,Heater Relay2,加热器继电器2
18-3,Right Front:SPW Input Voltage High,右前:SPW 输入电压高
18-4,Brake Switch Circuit,制动开关电路
18-5,Injector #1,#3,喷油嘴#1,#3
18-6,Main Duty Solenoid Valve,主占空比电磁阀
18-7,Feedback Solenoid Circuit Short to Battery,反馈电磁阀电路与蓄电池短路
18-8,Feedback Solenoid Circuit Open/Short to Ground,反馈电磁阀电路断路/与搭铁短路
18-9,Ignition High,点火开关电压高
1818,Dosing Pump Circuit Open A,定量泵电路断路A
1818-1,Dosing Pump Circuit Open,定量泵电路断路
1818-2,Dosing Pump Circuit Open or Short to Battery,定量泵电路断路或与蓄电池短路
1819,Combustion Air Fan Circuit Open or Short to Battery A,燃烧空气风扇电路断路或与蓄电池短路A 1819-1,Combustion Air Fan Circuit Open or Short to Battery,燃烧空气风扇电路断路或与蓄电池短路181A,Glow Plug Circuit Open A,预热塞电路断路A
181A-1,Combustion Air Fan Circuit Open,燃烧空气风扇电路断路
181A-2,Glow Plug Circuit Open,预热塞电路断路
181B,Water Pump:Open Circuit A,水泵:电路断路A
181B-1,Water Pump:Open Circuit,水泵:电路断路
19,Left Front:SPW Input Voltage High,左前:SPW 输入电压高
19-1,Defective Tone Wheel,有缺陷的信号轮
19-2,Right Front:SPW Low Speed Error,右前:SPW 低速故障
19-3,Reuse Error,再利用故障
19-4,Injector #2,#4,喷油嘴#2,#4
1A05,Undervoltage A,过低电压A
1A05-1,Undervoltage,过低电压
1C04,Overvoltage A,电压过高A
1C04-1,Overvoltage,电压过高
1C07,Overheating
1C07-1,Overheating(Water Temp.>125℃),过热(水温>125℃)
2,Right Front Sensor Error,右前传感器故障
2-1,Main eft Rear PSW Lin Error,主:左后PSW 电路故障
2-2,Main:Right Rear WDW Lin Error,主:右后WDW电路故障
2-3,Seat Recline Motor or Sensor Error,座椅倾斜电机或传感器故障
2-4,Telescope Motor or Sensor Error,伸缩电机或传感器故障
20,Ignition Switch 2,点火开关2
20-1,Left Front:SPW Motor Low Speed Error,左前:SPW 电机低速故障
20-2,Right Rear:SPW Motor Hall Sensor 1 Error,右后:SPW 电机霍尔传感器 1 故障
20-3,Start Solenoid Valve,起动电磁阀
20-4,Start Solenoid (Open/Short to Ground),起动电磁阀(断路/与搭铁电路短路)
20-5,Radiator Cooling Fan,散热器风扇
20-7,EEPROM Error,EEPROM 故障
200,PAB Seat Belt Pretensioner Open,PAB 座椅安全带拉紧器断路
2001,Control Module or Checksum H,控制模块或检测sum H
2001-2,Control Module or Checksum F,控制模块或检测sum F
2002,No Start ,No Flame-Up F,不起动，不点火e-Up F
2002-1,No Start ,No Flame-Up H,不起动，不点火-Up H
2002-2,No Start, No Flame-Up Even after Restart H,不起动，不点火-重新启动后上升平稳 H 2003,Flame-Out During Operation with No Further Flame-Up F,工作中燃烧停止F
2003-1,Flame-Out During Operation H,工作中燃烧停止H
2003-2,Flame-Out During Operation with No Further Flame-Up H,工作中燃烧停止H
2006,Flame Prior to Combustion Operation F,燃烧工作前点火F
2006-1,Flame Prior to Combustion Operation H,燃烧工作前点火H
2006-2,Flame Prior to Combustion Operation H,燃烧工作前点火H
201,PAB Seat Belt P/T Short,PAB 座椅安全带P/T 短路
2013,3 Times Flame-Out During Heating Cycle F,加热周期F期间3次燃烧停止
2013-1,3 Times Flame-Out During Heating Cycle H,加热周期F期间3次燃烧停止
2015,Engine Load(MAP Sensor),发动机负荷(MAP 传感器)
2016,Fuel Cut Solenoid,燃油切断电磁阀
2017,Second Air Solenoid,二次进气电磁阀
202,PAB Seat Belt Pretensioner Short to Battery,PAB 座椅安全带拉紧器与蓄电池短路
203,PAB Seat Belt Pretensioner Short to Ground,PAB 座椅安全带拉紧器与搭铁电路短路
21,Left Front Solenoid Circuit-Short to Battery,左前电磁阀电路-与蓄电池短路
21-1,Main eft Rear PSW Lin Error,主:左后PSW 电路故障
21-11,Right Rear:SPW Motor Hall Sensor 2 Error,右后:SPW 电机霍尔传感器 2 故障
21-12,Open/Shorted Sensor-Left Front,左前传感器断路/短路
21-13,Inlet Valve Right Front,右前输入阀
21-14,Right Front Wheel Speed Sensor Continuity Fault,右前轮速传感器导通故障
21-15,Input Voltage Low,输入电压低
21-16,Set Switch On,设定开关On
21-17,Left Rear:SPW Motor Hall Sensor 1 Error,左后:SPW 电机霍尔传感器1 故障21-18,Engine Coolant Temperature Sensor,发动机冷却水温度传感器
21-19,21.Solenoid No.1 Open,21.电磁阀1号断路
21-2,Throttle Position Sensor-Short Circuit,节气门位置传感器-短路电路
21-20,LF Solenoid Circuit-Short to Battery,LF 电磁阀电路-与蓄电池短路
21-21,Engine Coolant Temperature Circuit,发动机冷却水温度电路
21-3,Evaporator Temperature Sensor Open(High),蒸发器温度传感器断路(高)
21-4,Engine Coolant Temperature Circuit,发动机冷却水温度电路
21-5,Solenoid No.1 Open,电磁阀1 断路
21-6,Driver Airbag Short,驾驶席安全气囊电路短路
21-8,Left Front Wheel Speed Sensor,左前轮速传感器
21-9,Front Wheel Speed Sensor,前轮速传感器
22,Left Rear:SPW Motor Hall Sensor 2 Error,左后:SPW 电机霍尔传感器 2 故障
22-1,Throttle Position Sensor-Open Circuit,节气门位置传感器-电路断路
22-10,Anti-Lock Brake System-Fail,防抱死制动系统-故障
22-11,Right Front Wheel Speed Sensor,右前轮速传感器
22-12,Left Front Solenoid Circuit-Short to Ground,左前电磁阀电路-与搭铁电路短路22-13,Right Rear:SPW Normalization Error,右后:SPW 正常故障
22-14,Outlet Valve -Right Front,输出阀-右前
22-15,Injector #4,喷油嘴#4
22-16,Right Front Wheel Speed Sensor Fault,右前轮速传感器故障
22-17,Input Voltage High,输入电压高
22-18,Slow Cut Solenoid Valve,切断电磁阀慢
22-19,Fuel-Cut Valve(Open/Short to Ground),燃油-切断阀(断路/与搭铁电路短路)
22-2,Evaporator Temperature Sensor Short(Low),蒸发器温度传感器短路(低)
22-21,ABS Warning Lamp,ABS 警告灯
22-212,22.Solenoid No.1 Short,22.电磁阀1号短路
22-22,Resume Switch On,恢复开关On
22-23,Passenger Configuration Fault,助手席配置故障
22-24,LF Solenoid Circuit-Short to Ground,LF 电磁阀电路-与搭铁电路短路
22-25,Left Front Height Sensor,左前高度调节传感器
22-3,Front Height Sensor,前高度调节传感器
22-5,Crankshaft Position Sensor,曲轴位置传感器
22-7,Driver Airbag Open,驾驶席安全气囊电路断路
22-8,Fuel-Cut Solenoid Valve,燃油-切断电磁阀
22-9,Solenoid No.1 Short,电磁阀1 短路
22-a,Idle Adaption,怠速适应
23,Left Rear:SPW Normalization Error,左后:SPW 正常故障
23-,RF Solenoid Circuit-Short Battery,RF 电磁阀电路-与蓄电池短路
23-1,Solenoid No.2 Open,电磁阀2 断路
23-10,Right Front Solenoid Circuit-Short Battery,右前电磁阀电路-与蓄电池短路
23-11,Right Rear:SPW Unit Error,右后:SPW 模块故障
23-12,Open/Shorted Sensor-Right Front,右前传感器断路/短路
23-13,Inlet Valve Left Front,左前输入阀
23-14,Injector #3,喷油嘴#3
23-17,Idle-Up Solenoid Valve,快怠速电磁阀
23-18,ABS Warning Lamp Relay,ABS警告灯继电器
23-19,Cancel Switch On,取消开关On
23-20,Checksum Error,检测sum故障
23-21,23.Solenoid No.2 Open,23.电磁阀2号断路
23-22,Idle-Up Solenoid Valve,快怠速电磁阀
23-23,Right Front Height Sensor,右前高度传感器
23-3,Left Rear Wheel Speed Sensor,左后轮速传感器
23-4,Rear Height Sensor,后高度传感器
23-9,HO2S (Right),氧传感器(右)
24,Left Rear:SPW Unit Error,左后:SPW 模块故障
24-1,Right Rear Wheel Speed Sensor,右后轮速传感器
24-10,Open/Shorted Sensor-Left Rear,左后传感器断路/短路
24-11,Outlet Valve -Left Front,输出阀-左前
24-13,ABS Power Relay,ABS电源继电器
24-14,40km/h Over,高于40km/h
24-15,Open/Shorted Sensor(Rear),传感器断路/短路(后)
24-16,Parameter Table Error,参数表错误
24-17,TPS Idle Switch Short Of Bad Adjustment,不良调整引起的TPS怠速开关短路
24-18,24.Solenoid No.2 Short,24.电磁阀2号短路
24-19,RF Solenoid Circuit-Short Ground,RF 电磁阀电路-与搭铁电路短路
24-20,Second Air Solenoid Valve,二次进气电磁阀
24-4,Feedback System(Right),反馈系统(右)
24-6,Solenoid No.2 Short,电磁阀2 短路
24-7,Right Front Solenoid Circuit-Short Ground,右前电磁阀电路-与搭铁电路短路
24-8,Right Rear:Motor Hall Sensor Conut Dir.Error,右后:电机霍尔传感器反方向故障
24-9,Open/Shorted Sensor-Right Rear,右后传感器断路/短路
25,Left Rear:Motor Hall Sensor Counter Direction Error,左后:电机霍尔传感器计数器方向故障25-1,Kickdown Servo Switch-Open Circuit,强制将档伺服开关-电路断路
25-10,Inlet Valve Right Rear,右后输入阀
25-12,Q Adjusting Resister,Q 调节电阻器
25-13,Left Front Wheel Speed Sensor Continuity Fault,左前轮速传感器导通故障
25-15,40km/h Lower,低于40km/h
25-16,Closed Throttle Position Switch-Short Circuit,关闭节气门位置开关-电路短路
25-17,25.Solenoid No.3 Open,25.电磁阀3号断路
25-18,Left Rear Solenoid Circuit-Short to Battery,左后电磁阀电路-与蓄电池短路
25-19,Rear Wheel Sensor-Temporarily,后轮速传感器-暂时性
25-2,Rear Wheel Sensor-Temporarily,后轮速传感器-暂时性
25-3,Fuel Pressure Solenoid Valve,燃油压力电磁阀
25-4,Solenoid No.3 Open,电磁阀3 断路
25-6,Rear Pressure Sensor,后压力传感器
25-7,Barometric Pressure Sensor Circuit,大气压力传感器电路
25-8,Left Rear Solenoid Circuit-Short to Battery,左后电磁阀电路-与蓄电池短路
25-9,Right Rear:Motor Thermal Protection Error,右后:电机热保护故障
26,Left Rear:Motor Thermal Protection Error,左后:电机热保护故障
26-1,Solenoid No.3 Short,电磁阀3 短路
26-10,Outlet Valve -Right Rear,输出阀-右后
26-11,Left Front Wheel Speed Sensor Fault,左前轮速传感器故障
26-12,Wheel Speed Sensor Output Signal,轮速传感器输出信号
26-13,26.Solenoid No.3 Short,26.电磁阀3号短路
26-14,Left Rear Solenoid Circuit-Short to Ground,左后电磁阀电路-与搭铁电路短路
26-2,Kickdown Servo Switch-Short Circuit,强制将档伺服开关-电路短路
26-3,Purge Control Solenoid Valve,净化控制电磁阀
26-6,Rear Wheel Sensor-Permanently,后轮速传感器-永久性
26-7,Left Rear Solenoid Circuit-Short to Ground,左后电磁阀电路-与搭铁电路短路
26-8,Right Rear:Motor Holl Sensor Power Line Short,右后:电机霍尔传感器电源电路短路
26-9,Missing Sensor-Left Front,缺少传感器-左前
老车故障码2608,Dosing Pump Circuit Short to Ground F,定量泵电路与搭铁电路短路 F 2608-1,Dosing Pump Circuit Short to Ground H,定量泵电路与搭铁电路短路H
2608-2,Dosing Pump: Short Circuit Against Ground H,定量泵: 搭铁电路短路H
2609,Combustion Air Fan Circuit Short to Ground F,燃烧空气风扇电路与搭铁电路短路F 2609-1,Combustion Air Fan Circuit Short to Ground H,燃烧空气风扇电路与搭铁电路短路H 260A,Glow Plug Circuit Short to Ground F,预热塞电路与搭铁电路短路F
260A-1,Glow Plug Circuit Short to Ground H,预热塞电路与搭铁电路短路H
260B,Water Pump:Circuit Ground F,水泵:搭铁电路F
260B-1,Water Pump:Circuit Ground H,水泵:搭铁电路H
260B-2,Water Pump: Short Circuit Against Ground H,水泵: 搭铁电路短路H
260C,Vehicle Air Fan:Circuit Ground F,车辆空气风扇:搭铁电路F
260C-1,Vehicle Air Fan:Circuit Ground H,车辆空气风扇:搭铁电路H
260C-2,Vehicle Air Fan: Short Circuit Against Ground H,车辆空气风扇: 搭铁电路短路H 27,Left Rear:Motor Hall Sensor Power Line Short,左后:电机霍尔传感器电源电路短路
27-1,Ignition Pulse Line-Open Circuit,点火开关脉冲电路-断路
27-2,Belt Pretensioner Front-Passenger Open,安全带预紧器前-助手席断路
27-3,Right Rear Solenoid Circuit-Short Battery,右后电磁阀电路-与蓄电池短路
27-4,Missing Sensor-Right Front,缺少传感器-右前
27-5,Inlet Valve Left Rear,左后输入阀
27-6,Right Rear:Spw Input Voltage Very Low,右后:Spw 输入电压过低
28,Right Rear Solenoid Circuit-Short Ground,右后电磁阀电路-与搭铁电路短路
28-1,Accelerator Switch-Short Circuit,加速踏板开关-电路短路
28-10,EGR Valve(Short to Battery),EGR 阀(与蓄电池短路)
28-11,EGR Valve(Open/Short to Ground),EGR 阀(断路/与搭铁短路)
28-12,Left Rear:Spw Input Voltage Very Low,左后:Spw 输入电压非常低
28-2,Belt Pretensioner Front-Driver Open,安全带预紧器前-驾驶席断路
28-3,EGR Unit(Vacuum Side),EGR 模块(真空侧)
28-4,EGR Unit,EGR 模块
28-5,Right Rear:SPW Input Voltage Low,右后:SPW输入电压低
28-6,Missing Sensor(Rear),缺少传感器(后)
28-7,Missing Sensor-Left Rear,缺少传感器-左后
28-8,Outlet Valve -Left Rear,输出阀-左后
28-9,A/C Compressor,空调压缩机
2818,Dosing Pump Circuit Open F,定量泵电路断路F
2818-1,Dosing Pump Circuit Open H,定量泵电路断路H
2818-2,Dosing Pump Circuit Open or Short to Battery H,定量泵电路断路或与蓄电池短路H
2819,Combustion Air Fan Circuit Open or Short to Battery F,燃烧空气风扇电路断路或与蓄电池短路F 2819-1,Combustion Air Fan Circuit Open or Short to Battery H,燃烧空气风扇电路断路或与蓄电池短路H 281A,Glow Plug Circuit Open F,预热塞电路断路F
281A-1,Combustion Air Fan Circuit Open H,燃烧空气风扇电路断路H
281A-2,Glow Plug Circuit Open H,预热塞电路断路H
281B,Water Pump:Open Circuit F,水泵:电路断路F
281B-1,Water Pump:Open Circuit H,水泵:电路断路H
281B-2,Water Pump: Open Circuit H,水泵: 电路断路H
29,Left Rear:SPW Input Voltage Low,左后:SPW 输入电压低
29-1,EGR Unit(Barometric Side),EGR 模块(气压侧)
29-3,Flash Code,闪光器代码
29-4,Right Rear:SPW Input Voltage High,右后:SPW 输入电压高
29-5,Driver Configuration Fault,驾驶席配置故障
29-6,Diag Init Short to Ground,诊断电路与搭铁电路短路
29-7,Missing Sensor-Right Rear,缺少传感器-右后
2A05,Undervoltage F,过低电压F
2A05-1,Undervoltage H,过低电压H
2C04,Overvoltage F,电压过高F
2C04-1,Overvoltage H,电压过高H
2C07,Overheating
2C07-1,Overheating(Water Temp.>125℃) H,过热(水温>125℃) H
2C07-2,Overheating (Water Temperature > 125 °C) H,过热(水温> 125 °C) H
3,Trunk Open Error,行李箱打开错误
3-1,Main:Switch Module Lin Error,主:开关模块电路故障
3-2,Main:RH Outside Mirror Horizontal Motor/Sensor Error,主:RH 左室外后视镜或水平电机/传感器故障3-4,Right Front Motor/Sensor Error,右前电机/传感器故障
30-1,Left Rear:SPW Input Voltage High,左后:SPW 输入电压高
30-2,Main:Right Outside Mirror Horizontal Motor/Sensor Error,主:右室外后视镜或水平电机/传感器故障30-4,Passenger Configuration Fault,助手席配置故障
31,Left Rear:SPW Motor Low Speed Error,左后:SPW 电机低速故障
31-10,Wheel Speed Sensor Right Front,右前轮速传感器
31-11,Feedback System(Injection),反馈系统(喷射)
31-12,Ignition Switch Signal,点火开关信号
31-13,ACU Fault,ACU 故障
31-14,31.Vehicle Speed Sensor,31.车速传感器
31-15,Exhaust Valve,排气阀
31-3,Steering Angle Sensor-Open,转向角传感器-断路
31-4,Transaxle Control Module,变速器控制模块
31-5,Knock Sensor,爆震传感器
31-6,Air Mixture Damper Position,温度门减震器位置
31-7,Pulse Generator A-Open Circuit,脉冲发生器A-电路断路
31-8,LF Wheel Speed Sensor-Air Gap,LF 轮速传感器-气隙
31-9,Simultaneous Dropout/Right Front,同时丢码/右前
31-A,Maximum RPM Surpassed,超过最大RPM
32,RF Wheel Speed Sensor-Air Gap,RF 轮速传感器-气隙
32-1,Steering Angle Sensor-Short,转向角传感器-短路
32-10,Right Rear Wheel Speed Sensor Fault,右后轮速传感器故障
32-11,Timing Overflow,正时过大
32-2,2nd Air Solenoid Valve,二次空气电磁阀
32-3,Pulse Generator B-Open Circuit,脉冲发生器B-电路断路
32-4,TCM-First Gear Command,TCM-1档控制
32-5,Damper Position Mode,减震器位置模式
32-6,Erratic Sensor(LF),不稳定传感器(LF)
32-7,Wheel Speed Sensor Left Front,左前轮速传感器
32-8,TPS Sensor,TPS 传感器
32-9,Right Rear Wheel Speed Sensor Continuity Fault,右后轮速传感器导通故障
33,Steering Wheel Neutral Detect Sensor,方向盘空档检测传感器
33-1,Cranking Signal Circuit-Short,曲轴信号电路-电路
33-2,Steering Angle Sensor-Fail,转向角传感器-故障
33-3,Throttle Position Valve,节气门位置阀
33-4,Left Rear Wheel Speed Sensor-Air Gap,左后轮速传感器-气隙
33-6,Feedback System(Injection Timing),反馈系统(喷射时间)
33-8,Power Supply Low,电源电路与搭铁电路短路
34,Right Rear Wheel Speed Sensor-Air Gap,右后轮速传感器-气隙
34-1,Shift Switches,换档开关
34-10,Power Supply High,电源电压高
34-11,Watchdog Fault,监测器故障
34-12,34.Shift Switches,34.换档开关
34-2,Idle Speed Control Valve,怠速控制阀
34-3,Steering Angle Sensor-Power,转向角传感器-电源
34-4,Connector Shorting Bar-Fail,连接器短路片-故障
34-5,Erratic Sensor(RF),不稳定传感器(RF)
34-6,Engine Load Solenoid Valve,发动机负荷电磁阀
34-8,Idle-Up Solenoid Valve 1 (Short to Battery),快怠速电磁阀1 (与蓄电池短路)
34-9,Idle-Up Solenoid Valve 1 (Open/Short to Battery),快怠速电磁阀1 (断路/与蓄电池短路) 34-A,Idle Control Valve,怠速控制阀
35-1,Engine Speed Signal,发动机速度信号
35-10,Idle-Up Solenoid Valve 2 (Short to Battery),快怠速电磁阀2 (与蓄电池短路)
35-11,Idle-Up Solenoid Valve 2 (Open/Short to Ground),快怠速电磁阀2 (断路/与搭铁电路短路)
35-15,35.Engine Speed Signal not Input,35.发动机速度信号无输入
35-2,Steering Angle Sensor-Neutral,转向角传感器-空档
35-3,Slow Duty Solenoid Valve,Slow占空比电磁阀
35-4,Erratic Sensor(Rear),不稳定传感器(后)
35-5,Erratic Sensor(LR),不稳定传感器(LR)
35-6,Left Rear Wheel Speed Sensor Continuity Fault,左后轮速传感器导通故障
35-8,Left Front Preview Sensor,左前预览传感器
35-9,DRB Module Short to Ground,DRB模块与搭铁短路
35-A,O2 Adaption: DTV,氧适应: DTV
36,Motor Pump Relay-Short to Ground,电机泵继电器-与搭铁电路短路
36-1,HO2S Heater Relay,氧传感器加热器继电器
36-10,Idle-Up Solenoid Valve 3 (Short to Battery),快怠速电磁阀3 (与蓄电池短路)
36-11,Idle-Up Solenoid Valve 3 (Open/Short to Battery),快怠速电磁阀3 (断路/与蓄电池短路)
36-17,Erratic Sensor(Right Rear),不稳定传感器(右后)
36-2,Heater Relay1,加热器继电器1
36-3,Glow Plug Relay,预热塞继电器
36-4,A/C Idle Up Solenoid Valve,空调怠速上部电磁阀
36-5,Ignition Timing Adjust Signal,点火正时调节信号
36-6,Left Rear Wheel Speed Sensor Fault,左后轮速传感器故障
36-7,Steering Wheel Sensor-N,方向盘传感器-N
36-8,Right Front Preview Sensor,右前预览传感器
36-9,DRB Module Short to Battery,DRB模块与蓄电池短路
36-A,O2 Adaption: FRA,氧适应: FRA
37,Motor Pump Relay-Short to Battery,电机泵继电器-与蓄电池短路
37-1,Wheel Speed Error Detect,轮速错误检测
37-2,ADU Incomplete Connection,ADU 不完全连接
37-3,ADU Incomplete Connection(INT),ADU 不完全连接(INT)
37-4,Steering Wheel Sensor-1,2,方向盘传感器-1,2
37-6,ADU Incomplete Connection H,ADU 不完全连接H
37-8,Transmission Range Sensor Circuit Open,变速器档位传感器电路断路
37-9,O2 Adaption: TRA,氧适应: TRA
38,O2 Sensor Heater Circuit Malfunction,氧传感器加热器电路故障
38-1,Motor Pump Circuit-Short to Ground,电机泵电路-与搭铁电路短路
38-2,RPM Signal Fault,RPM 信号故障
38-5,Ignition Pulse,点火开关脉冲
39,Motor Pump Circuit-Short to Battery,电机泵电路-与蓄电池短路
39-1,Passenger Module Short to Ground,助手席模块与搭铁电路短路
3B,Passenger Module Short,助手席模块短路
3D,Pretensioner Front-Driver Short to Ground,拉紧器前-驾驶席与搭铁电路短路
3E,Pretensioner Front-Driver Short to Battery,拉紧器前-驾驶席与蓄电池短路
3F,Pretensioner Front-Driver Short,拉紧器前-驾驶席短路
4-1,Main eft Outside Mirror Horizontal Motor/Sensor Error,主:左室外后视镜或水平电机/传感器故障
4-2,Main:Right Outside Mirror Vertical Motor/Sensor Error,主:右室外后视镜或垂直电机/传感器故障4-3,Lost Communication Between Tilt/Telescope and BCM,倾斜/伸缩装置与BCM之间失去通信
4-4,Right Rear Motor/Sensor Error,右后电机/传感器故障
40,Pretensioner Front-Driver Open,拉紧器前-驾驶席断路
40-1,DICS Solenoid Valve,DICS 电磁阀
4016,Feedback Solenoid,反馈电磁阀
4017,HO2S Heater,氧传感器加热器
41,Fail Safe Relay Circuit-Short to Battery,失效保护继电器电路-与蓄电池短路
41-1,TPS 5V Reference Open/Short to Ground,TPS 5V 参考电压电路断路/与搭铁电路短路
41-10,Open Isolation Solenoid-Left Front,左前隔离电磁阀断路
41-11,Power Supply Over Voltage,电源电压过高
41-12,Actuator(Step Motor),执行器(步进电动机)
41-13,CPU(A/D),CPU(A/D)
41-14,Right Front ABS Inlet Valve Solenoid Fault,右前ABS 加压阀电磁阀故障
41-15,LF Solenoid Valve,LF 电磁阀
41-17,VICS Valve(Short to Battery),VICS 阀(与蓄电池短路)
41-18,VICS Valve(Open/Short to Ground),VICS 阀(断路/与搭铁电路短路)
41-19,FSR Circuit Short(Ground),FSR 电路短路(搭铁)
41-20,Height Adjust,高度调节
41-3,Front Actuator Circuit,前执行器电路
41-4,SCSV A-Open Circuit,SCSV A-电路断路
41-5,Injector,喷油嘴
41-7,Air Mixture Damper Motor,温度门减震器电机
41-9,VICS Solenoid Valve,VICS 电磁阀
42,Fail Safe Relay Circuit-Short to Ground,失效保护继电器电路-与搭铁短路
42-1,Engine-Throttle System,发动机-节汽门系统
42-10,Warning Lamp Short to Ground/Open,警告灯与搭铁电路短路/断路
42-11,Warning Lamp Short to Ground/Open(INT),警告灯与搭铁电路短路/断路(INT)
42-12,CPU(DSD3),CPU(DSD3)
42-13,Solenoid Power Supply Relay,电磁阀电源继电器
42-14,Right Front ABS Outlet Valve Solenoid Fault,右前ABS 减压阀电磁阀故障
42-15,RF Solenoid Valve,RF 电磁阀
42-17,Warning Lamp Short to Ground/Open H,警告灯与搭铁电路短路/断路H
42-2,Fuel Pump,燃油泵
42-3,DDS Output Error,DDS 输出故障
42-4,Rear Actuator Circuit,后执行器电路
42-5,SCSV A-Short Circuit,SCSV A-短路电路
42-6,Damper Motor Mode,减震器电机模式
42-7,ECS Relay,ECS 继电器
42-8,TPS 5V Reference Short to Battery,TPS 5V 参考电压电路与蓄电池短路
42-9,Open Dump Solenoid-Left Front,左前倾斜电磁阀断路
43,Fail Safe Relay Coil,失效保护继电器线圈
43-1,SRS SRI Circuit-Open,SRS SRI 电路-断路
43-10,Compressor Relay,压缩机继电器
43-11,Prime Line Solenoid Fault(ASV) TCS,主要线路电磁阀故障(ASV) TCS
43-12,Left Rear Solenoid Valve,左后电磁阀
43-15,FSR Circuit Short(Battery),FSR 电路短路(蓄电池)
43-2,SCSV B-Open Circuit,SCSV B-电路断路
43-3,Malfunction Indicator Lamp (MIL) Control Circuit,故障指示灯(MIL) 控制电路
43-5,Throttle/Pedal Position Sensor/Switch Short to Battery,节气门/踏板位置传感器/开关与蓄电池短路
43-6,EGR System,EGR系统
43-7,Compressor Relay,压缩机继电器
43-8,Open Isolation Solenoid-Right Front,右前隔离电磁阀断路
43-9,Acceleration Pedal Position Reference Voltage,加速踏板位置参考电压
44,ABS Warning Lamp Circuit-Short Ground,ABS 警告灯电路-与搭铁短路
44-1,SRS SRI Control Malfunction,SRS SRI 控制故障
44-10,Boost Pressure Sensor Reference Voltage Malfunction,助力器传感器规定电压故障
44-11,Pilot Valve Solenoid Fault(ASV) TCS,辅助电磁阀故障(ASV) TCS
44-12,Right Rear Solenoid Valve,右后电磁阀
44-14,Ignition System Cylinder No.1&4,点火系统气缸编号1&4
44-16,Ignition System Cylinder No.1&4,点火系统气缸编号1&4
44-2,SCSV B-Short Circuit,SCSV B-短路电路
44-3,Throttle/Pedal Position Sensor/Switch Open/Short to Ground,节气门/踏板位置传感器/开关断路/与搭铁电路短路
44-4,Rear Actuator Malfunction,后执行器故障
44-7,Return Pump Relay,回位泵继电器
44-8,Warning Lamp Short to Battery,警告灯与蓄电池短路
44-9,Warning Lamp Short to Battery(Int),警告灯与蓄电池短路(Int)
45,ABS Warning Lamp Diode-Open,ABS 警告灯二极管-断路
45-1,Exhaust Valve Actuation,排气阀启动
45-2,PCSV-Open Circuit,PCSV-电路断路
45-4,SRS Control Module,SRS 控制模块
45-5,Open Dump Solenoid-Right Front,右前倾斜电磁阀断路
45-6,Battery Error,蓄电池故障
45-7,Left Front ABS Inlet Valve Solenoid Fault,左前ABS 加压电磁阀故障
45-8,Left Front Cut Valve,左前切断阀
46,Open Isolation Solenoid-Right Rear,右后隔离电磁阀断路
46-1,A/C Cut Relay,空调切断继电器
46-10,Evaporative Emission System-Purge Control Valve Circuit,蒸发排放系统-净化控制阀电路
46-2,PCSV-Short Circuit,PCSV-短路
46-3,Flow Control Valve,流动控制阀
46-4,Open Isolation Solenoid-Left Rear,左后隔离电磁阀断路
46-5,PCM Data(EEPROM),PCM 数据(EEPROM)
46-6,Left Front ABS Outlet Valve Solenoid Fault,左前ABS 减压电磁阀故障
46-7,Right Front Cut Valve,右前切断阀
46-8,Evaporative Emission System-Purge Control Valve Circuit,蒸发排放系统-净化控制阀电路
46-9,Open Isolation Solenoid(Rear),后隔离电磁阀断路
47,Open Dump Solenoid-Right Rear,右后倾斜电磁阀断路
47-1,Torque Converter Clutch Circuit Open,液力变矩器离合器电路断路
47-2,Active Exhaust Valve,激活排放阀
47-20,Supply Valve Malfunction,供给阀故障
47-3,Open Dump Solenoid-Left Rear,左后倾斜电磁阀断路
47-4,Left Front Intro Valve,左前Intro 阀
47-5,Open Dump Solenoid(Rear),后倾斜电磁阀断路
P0500;Vehicle Speed Sensor "A";车辆速度传感器"A"
P0501;Vehicle Speed Sensor "A" Range/Performance;车辆速度传感器"A"范围/性能
P0502;Vehicle Speed Sensor "A" Circuit Low Input;车辆速度传感器"A"电路低输入
P0503;Vehicle Speed Sensor "A" Intermittent/Erratic/High;车辆速度传感器"A"间歇/不稳定/高
P0504;Brake Switch "A"/"B" Correlation;制动开关"A"/"B"相关关系
P0505;Idle Air Control System;怠速空气控制系统
P0506;Idle Air Control System RPM Lower Than Expected;怠速空气控制系统RPM低于期望值
P0507;Idle Air Control System RPM Higher Than Expected;怠速空气控制系统RPM高于期望值
P0508;Idle Air Control System Circuit Low;
P0509;Idle Air Control System Circuit High;
P0510;Closed Throttle Position Switch;关闭节气门位置开关
P0511;Idle Air Control Circuit;怠速空气控制电路
P0512;Starter Request Circuit;
P0513;Incorrect Immobilizer Key;
P0514;Battery Temperature Sensor Circuit Range/Performance;
P0515;Battery Temperature Sensor Circuit;
P0516;Battery Temperature Sensor Circuit Low;
P0517;Battery Temperature Sensor Circuit High;
P0518;Idle Air Control Circuit Intermittent;
P0519;Idle Air Control System Performance;
P0520;Engine Oil Pressure Sensor/Switch Circuit;
P0521;Engine Oil Pressure Sensor/Switch Range/Performance;
P0522;Engine Oil Pressure Sensor/Switch Low Voltage;
P0523;Engine Oil Pressure Sensor/Switch High Voltage;
P0524;Engine Oil Pressure Too Low;
P0525;Cruise Control Servo Control Circuit Range/Performance;
P0526;Fan Speed Sensor Circuit;
P0527;Fan Speed Sensor Circuit Range/Performance;
P0528;Fan Speed Sensor Circuit No Signal;
P0529;Fan Speed Sensor Circuit Intermittent;
P0530;A/C Refrigerant Pressure Sensor "A" Circuit;A/C制冷剂压力传感器"A"电路
P0531;A/C Refrigerant Pressure Sensor "A" Circuit Range/Performance;A/C制冷剂压力传感器"A"电路范围/性能
P0532;A/C Refrigerant Pressure Sensor "A" Circuit Low;A/C制冷剂压力传感器"A"电路低
P0533;A/C Refrigerant Pressure Sensor "A" Circuit High;A/C制冷剂压力传感器"A"电路高
P0534;Air Conditioner Refrigerant Charge Loss;
P0535;A/C Evaporator Temperature Sensor Circuit;
P0536;A/C Evaporator Temperature Sensor Circuit Range/Performance;
P0537;A/C Evaporator Temperature Sensor Circuit Low;
P0538;A/C Evaporator Temperature Sensor Circuit High;
P0539;A/C Evaporator Temperature Sensor Circuit Intermittent;
P0540;Intake Air Heater "A" Circuit;进气空气加热器"A"电路
P0541;Intake Air Heater "A" Circuit Low;进气空气加热器"A"电路低
P0542;Intake Air Heater "A" Circuit High;进气空气加热器"A"电路高
P0543;Intake Air Heater "A" Circuit Open;进气空气加热器"A"电路断路
P0544;Exhaust Gas Temperature Sensor Circuit Bank 1 Sensor 1;排气温度传感器电路1排传感器1
P0545;Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 1;排气温度传感器电路低1排传感器1
P0546;Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 1;排气温度传感器电路高1排传感器1
P0547;Exhaust Gas Temperature Sensor Circuit Bank 2 Sensor 1;
P0548;Exhaust Gas Temperature Sensor Circuit Low Bank 2 Sensor 1;
P0549;Exhaust Gas Temperature Sensor Circuit High Bank 2 Sensor 1;
P0550ower Steering Pressure Sensor/Switch Circuit;电动转向压力传感器/开关电路
P0551ower Steering Pressure Sensor/Switch Circuit Range/Performance;电动转向压力传感器/开关电路范围/性能
P0552ower Steering Pressure Sensor/Switch Circuit Low Input;电动转向压力传感器/开关电路低输入
P0553ower Steering Pressure Sensor/Switch Circuit High Input;电动转向压力传感器/开关电路高输入
P0554ower Steering Pressure Sensor/Switch Circuit Intermittent;
P0555;Brake Booster Pressure Sensor Circuit;
P0556;Brake Booster Pressure Sensor Circuit Range/Performance;
P0557;Brake Booster Pressure Sensor Circuit Low Input;
P0558;Brake Booster Pressure Sensor Circuit High Input;
P0559;Brake Booster Pressure Sensor Circuit Intermittent;
P0560;System Voltage;系统电压
P0561;System Voltage Unstable;系统电压不稳
P0562;System Voltage Low;系统电压低
P0563;System Voltage High;系统电压高
P0564;Cruise Control Multi-Function Input "A" Circuit;巡航控制多功能输入"A"电路P0565;Cruise Control On Signal;巡航控制接通信号
P0566;Cruise Control Off Signal;巡航控制切断信号
P0567;Cruise Control Resume Signal;巡航控制恢复信号
P0568;Cruise Control Set Signal;巡航控制设置信号
P0569;Cruise Control Coast Signal;
P0570;Cruise Control Accelerate Signal;
P0571;Brake Switch "A" Circuit;制动开关"A"电路
P0572;Brake Switch "A" Circuit Low;
P0573;Brake Switch "A" Circuit High;制动开关"A"电路高
P0574;Cruise Control System - Vehicle Speed Too High;巡航控制系统－车辆速度过高P0575;Cruise Control Input Circuit;
P0576;Cruise Control Input Circuit Low;
P0577;Cruise Control Input Circuit High;
P0578;Cruise Control Multi-Function Input "A" Circuit Stuck;
P0579;Cruise Control Multi-Function Input "A" Circuit Range/Performance;
P0580;Cruise Control Multi-Function Input "A" Circuit Low;
P0581;Cruise Control Multi-Function Input "A" Circuit High;
P0582;Cruise Control Vacuum Control Circuit/Open;
P0583;Cruise Control Vacuum Control Circuit Low;
P0584;Cruise Control Vacuum Control Circuit High;
P0585;Cruise Control Multi-Function Input "A"/"B" Correlation;
P0586;Cruise Control Vent Control Circuit/Open;
P0587;Cruise Control Vent Control Circuit Low;
P0588;Cruise Control Vent Control Circuit High;
P0589;Cruise Control Multi-Function Input "B" Circuit;
P0590;Cruise Control Multi-Function Input "B" Circuit Stuck;
P0591;Cruise Control Multi-Function Input "B" Circuit Range/Performance;
P0592;Cruise Control Multi-Function Input "B" Circuit Low;
P0593;Cruise Control Multi-Function Input "B" Circuit High;
P0594;Cruise Control Servo Control Circuit/Open;
P0595;Cruise Control Servo Control Circuit Low;
P0596;Cruise Control Servo Control Circuit High;
P0597;Thermostat Heater Control Circuit/Open;
P0598;Thermostat Heater Control Circuit Low;
P0599;Thermostat Heater Control Circuit High;
P0600;Serial Communication Link;串行通信连接
P0601;Internal Control Module Memory Check Sum Error;内部控制模块记忆检查总数错误
P0602;Control Module Programming Error;控制模块程序错误
P0603;Internal Control Module Keep Alive Memory (KAM) Error;
P0604;Internal Control Module Random Access Memory (RAM) Error;内部控制模块随机存储（RAM）错误
P0605;Internal Control Module Read Only Memory (ROM) Error;内部控制模块只读存储器
电脑常出现故障的英文翻译
1.开机BIOS出错提示 1 CMOS battery failed 中文：CMOS电池失效。解释：这说明CMOS电池已经快没电了，只要更换新的电池即可。 2 CMOS check sum error－Defaults loaded 中文：CMOS 执行全部检查时发现错误，要载入系统预设值。解释：一般来说出现这句话都是说电池快没电了，可以先换个电池试试，如果问题还是没有解决，那么说明CMOS RAM可能有问题，如果没过保修期就到经销商处换一块主板，过了保修期就让经销商送回生产厂家修一下吧！ 3 Press ESC to skip memory test 中文：正在进行内存检查，可按ESC键跳过。解释：这是因为在CMOS内没有设定跳过存储器的第2、3、4次测试，开机就会执行4次内存测试，当然你也可以按ESC键结束内存检查，不过每次都要这样做太麻烦了，你可以进入COMS设置后选择BIOS FEATURS SETUP，将其中的Quick Power On Self Test设为Enabled，储存后重新启动即可。 4 Keyboard error or no keyboard present 中文：键盘错误或者未接键盘。解释：检查一下键盘的连线是否松动或者损坏。 5 Hard disk install failure 中文：硬盘安装失败。解释：这是因为硬盘的电源线或数据线可能未接好或者硬盘跳线设置不当。你可以检查一下硬盘的各根连线是否插好，看看同一根数据线上的两个硬盘的跳线的设置是否一样，如果一样，只要将两个硬盘的跳线设置得不一样即可（一个设为Master，另一个设为Slave）。 6 Secondary slave hard fail 中文：检测从盘失败解释：可能是CMOS设置不当，比如说没有从盘但在CMOS里设为有从盘，那么就会出现这个出错提示，这时可以进入COMS设置选择IDE HDD AUTO DETECTION进行硬盘自动侦测。
常见电脑故障的英语提示
Press any key to continue 按任意一个键继续 Bad command or 坏的命令或文件名字 Press Del to enter setup 按删除键进入设置程序 Keyboard error or no keyboard present 键盘错误或不存在键盘Scanning memory for virus扫描内存为病毒 Scan and kill virus tools 扫描和杀病毒工具 Exit without saving 退出没有保存 Not ready reading driver D? 不准备读驱动器D Abort Retry fail 终止重试失败 Microsoft scan disk 微软扫描磁盘 Because windows was not properly shut down 因为windows不能正确的关闭 One or more of your disk drivers may have errors on it 一个或多个你的磁盘驱动器可能有错误 Disks write error 磁盘写错误 Unable to write to disk in driver A 不能写磁盘驱动器A Press ESC to return to disk options 按退出键返回分区选项 Load BIOS default 调BIOS默认值 User’s manual用户手册 Create DOS partition or logical DOS drive 建立DOS分区或逻辑DOS驱动器 Set active partition 设置活动分区 Delete partition or logical Dos drive 删除分区或逻辑DOS驱动器Current fixed disk drive 当前固定磁盘驱动器 TO avoid seeing this message again Always shut down your computer by
常见硬盘故障英文提示信息
硬盘常见英文提示 网上对硬盘错误的英文提示有很多的资料，我只是列出一些常见的硬盘故障的提示，主要针对喜欢折腾电脑的又是新手的朋友，高手绕道啊，呵呵。下面绝大部分是我遇见过的硬盘故障。 1、Date error（数据错误）： 从软盘或硬盘上读取数据不存在不可修复错误，磁盘上有坏扇区或坏的文件分配表。 2、Hard disk configuration error（硬盘配置错误）： 硬盘配置不正错，跳线不对，硬盘参数设置不正确等。 3、Hard disk controller failure（硬盘控制器失效）： 控制器卡（多功能卡）松动，连线不对，硬盘配置不正确，跳线不对，硬盘参数设置不正确等。 4、Hard disk failure(硬盘失效故障）： 控制器卡（多功能卡）故障，硬盘配置不正确，跳线不对，硬盘物理故障。 5、Hard disk drive read failure（硬盘驱动器读取失效）： 控制器卡（多功能卡）松动，硬盘配置不正确，硬盘参数设置不正确，硬盘记录数据被破坏等。 6、No boot device available（无引导设备）： 系统找不到为引导设备的软盘或硬盘。 7、No boot sector on hard disk drive （硬盘上无引导扇区）： 硬盘上引导扇区丢失，感染了病毒或配置参数不正确。 8、Non system disk or disk error（非系统盘或磁盘错误）： 作为引导的磁盘不是系统盘，不含有系统引导和核心文件，或磁盘片本身故障。 9、Sector not found （扇区未找到）： 系统在软盘和硬盘上不能定位给定扇区 10、seek error(搜索错误）： 系统在软盘和硬盘上不能定位给定扇区，磁道或磁头。 11、Reset failed（硬盘复位失败）： 硬盘或硬盘接口的电路故障。 12、Fatal error Rad Hard Disk（硬盘致命错误）： 硬盘或硬盘接口故障
电脑开机时各种故障的英文提示
电脑开机时各种故障的英文提示 1.CMOS battery failed 中文：CMOS电池失效。 解释：这说明CMOS电池已经快没电了，只要更换新的电池即可。 2.CMOS check sum error-Defaults loaded 中文：CMOS执行全部检查时发现错误，要载入系统预设值。 解释：一般来说出现这句话都是说电池快没电了，可以先换个电池试试，如果问题还是没有解决，那么说明CMOS RAM可能有问题，如果没过一年就到经销商处换一块主板，过了一年就让经销商送回生产厂家修一下吧！ l m+~l 3.Press ESC to skip memory test 中文：正在进行内存检查，可按ESC键跳过。 解释：这是因为在CMOS内没有设定跳过存储器的第二、三、四次测试，开机就会执行四次内存测试，当然你也可以按ESC键结束内存检查，不过每次都要这样太麻烦了，你可以进入COMS设置后选择BIOS FEATURS SETUP，将其中的Quick Power On Self Test设为Enabled，储存后重新启动即可。 4.Keyboard error or no keyboard present 中文：键盘错误或者未接键盘。 解释：检查一下键盘的连线是否松动或者损坏。 5.Hard disk install failure 中文：硬盘安装失败。 解释：这是因为硬盘的电源线或数据线可能未接好或者硬盘跳线设置不当。你可以检查一下硬盘的各根连线是否插好，看看同一根数据线上的两个硬盘的跳线的设置是否一样，如果一样，只要将两个硬盘的跳线设置的不一样即可(一个设为Master，另一个设为Slave)。 6.Secondary slave hard fail 中文：检测从盘失败 解释：可能是CMOS设置不当，比如说没有从盘但在CMOS里设为有从盘，那么就会出现错误，这时可以进入COMS设置选择IDE HDD AUTO DETECTION进行硬盘自动侦测。也可能是硬盘的电源线、数据线可能未接好或者硬盘跳线设置不当，解决方法参照第5条。 7.Floppy Disk(s) fail或Floppy Disk(s) fail(80)或Floppy Disk(s) fail(40) 中文：无法驱动软盘驱动器。
电脑常见故障的英语提示-1
电脑常见故障的英语提示 2010年10月15日星期五 02:01 P.M. 电脑常见故障的英语提示 Press any key to continue 按任意一个键继续 Bad command or file name 坏的命令或文件名字 Press Del to enter setup 按删除键进入设置程序 Keyboard error or no keyboard present 键盘错误或不存在键盘 Scanning memory for virus扫描内存为病毒 Scan and kill virus tools 扫描和杀病毒工具 Exit without saving 退出没有保存 Not ready reading driver D? 不准备读驱动器D Abort Retry fail 终止重试失败 Microsoft scan disk 微软扫描磁盘 Because windows was not properly shut down 因为windows不能正确的关闭One or more of your disk drivers may have errors on it 一个或多个你的磁盘驱动器可能有错误 Disks write error 磁盘写错误 Unable to write to disk in driver A 不能写磁盘驱动器A Press ESC to return to disk options 按退出键返回分区选项 Load BIOS default 调BIOS默认值 User’s manual 用户手册 Create DOS partition or logical DOS drive 建立DOS分区或逻辑DOS驱动器Set active partition 设置活动分区 Delete partition or logical Dos drive 删除分区或逻辑DOS驱动器 Current fixed disk drive 当前固定磁盘驱动器 TO avoid seeing this message again Always shut down your computer by selecting shut down from the start menu 避免看见这个消息再次总是关闭你的计算机选择关闭从开始菜单 DO you wish to use the maximum available size for a primary DOS partition and make the partition active? 你希望使用最大可用大小为一主DOS分区和使用这个分区激活 You must restart your system for your changes to take effect 你必须重新启动你的系统你的变化生效 Any drives you hare created or changed must be formatted after you restart 一些驱动器你已经建立或改变必须被格式化在你重启 Warning! Data in the deleted Extend DOS partition will be lost DO you wish continue 警告数据在这个删除扩展DOS分区将要被丢失你希望继续吗 Program cannot be run in DOS mode 程序不能被运行在DOS 模式 Choosing command form menu 从菜单选择命令 Opening and saving Document 打开和保存文档 Finding information in help 找信息在帮助里 More/ways to use file manager 更多方法使用文件管理器 Working with floppy disks 用软盘工作
(完整版)计算机软件专业考研英语面试必备问题
软件工程（或计算机专业）英语面试，这是本人复试是整理的，成绩一般，大神勿喷。为什么考研（很重要的点，我是软件工程专业的，本段是关于软件工程的） I learnt a lot from university courses during the past four year. However,I think furtherstudy is still urgent for me to realize self-value. Life is precious. It is necessary to seize any chance for self-development,especially in this competitive modern world. And,I am looking forward to making a solid foundation for future profession after two years study here. The major that I hope pursue for my further education is program design. Because I find software are playing a more and more important role in each part of our modern society. And nowadays in China, with the recognition by the government, our domestic software industry is growing rapidly and that may provide a lot of chances to us. I plan to concentrate on study and research in this field in my graduate time. And I hope I can form a systematic view of software engineering and make a solid foundation for future profession after three years study here. 自我介绍 Good morning. I am very glad to be here for this interview. First,let me introduce myself. I come from Suqian city jiangsu province. I will graduate from nanjing university of posts and telecommunications in july this year.In the university, my major is software engineering.I like this major, my ideal is to become an outstanding software engineer.I have learned a lot of courses in the college, data structure, database, software engineering, computer network, software testing, etc.I spent a lot of time to learn the course. In my spare time, I like reading some domestic and foreign literature and magazines, such as "Eugenie Grandet", "the reader". I think reading can increase their self-cultivation and logical ability, and it can exercise a person's patience. I am also very interested in the football, My favorite team is Real Madrid.(本段有语法错误，不过面试中，老师不会在意的，老师只会在意你的流畅度和发音。大神可自行修改) I learnt a lot from university courses during the past four year. However,I think further study is still urgent for me to realize self-value. Life is precious. It is necessary to seize any chance for self-development,especially in this competitive modern world. And,I am looking forward to making a solid foundation for future profession after Two and a half years study here. I want to improve programming ability. Because I find software are playing a more and more important role in each part of our modern society. And nowadays in China, with the recognition by the government, our domestic software industry is growing rapidly and that may provide a lot of chances to us. I plan to concentrate on study and research in this field in my graduate time. And I hope I can form a systematic view of software engineering and make a solid foundation for future profession after two and a half years study in this famous university. That is all, thank you very much. 问题篇（划线部分为必须掌握的点，听不懂的点千万别说pardon，就算再说一遍一般也听不懂） 1、Where are you from? 1、你来自哪里？ I come from suqian in the north of Jiangsu province, it is not famous, but it has a very long history. Suqian is the hometown of Xiang Yu.The native place of xiang yu is located at the ancient wotong lane, birthplace of the overlord in the west chu period.Every year a lot of people come to visit it.Suqian also has a very good ecological and cultural environment, I love my hometown.
电脑常见故障的英语提示
电脑常见故障的英语提示Press any key to continue 按任意一个键继续 Bad command or fil e name 坏的命令或文件名字 Press Del to enter setup 按删除键进入设置程序 Keyboard error or no keyboard present 键盘错误或不存在键盘 Scanning memory for virus 扫描内存为病毒 Scan and kill virus tools 扫描和杀病毒工具 Exit without saving 退出没有保存 Not ready reading driver D? 不准备读驱动器D Abort Retry fail 终止重试失败 Microsoft scan disk 微软扫描磁盘 Because wind ows was not properly shut down
因为wind ows不能正确的关闭 One or more of your disk drivers may have errors on it 一个或多个你的磁盘驱动器可能有错误 Disks write error 磁盘写错误 Unable to write to disk in driver A 不能写磁盘驱动器A Press ESC to return to disk options 按退出键返回分区选项 Load BIOS default 调BIOS默认值 User’s manual 用户手册 Create DOS partition or logical DOS drive 建立DOS分区或逻辑DOS驱动器 Set active partition 设置活动分区 Delete partition or logical Dos drive 删除分区或逻辑DOS驱动器 Current fixed disk drive 当前固定磁盘驱动器 TO avoid seeing this message again Always shut down your computer
电脑常用故障英文
电脑常用故障英文 Company Document number：WUUT-WUUY-WBBGB-BWYTT-1982GT
电脑常用故障英文 中文：CMOS电池失效。 解释：这说明CMOS电池已经快没电了，只要更换新的电池即可。 中文：CMOS执行全部检查时发现错误，要载入系统预设值。 解释：一般来说出现这句话都是说电池快没电了，可以先换个电池试试，如果问题还是没有解决，那么说明CMOSRAM可能有问题，如果没过一年就到经销商处换一块主板，过了一年就让经销商送回生产厂家修一下吧！ 中文：正在进行内存检查，可按ESC键跳过。 解释：这是因为在CMOS内没有设定跳过存储器的第二、三、四次测试，开机就会执行四次内存测试，当然你也可以按ESC键结束内存检查，不过每次都要这样太麻烦了，你可以进入COMS设置后选择BIOSFEATURSSETUP，将其中的QuickPowerOnSelfTest设为Enabled，储存后重新启动即可。 中文：键盘错误或者未接键盘。 解释：检查一下键盘的连线是否松动或者损坏。 中文：硬盘安装失败。 解释：这是因为硬盘的电源线或数据线可能未接好或者硬盘跳线设置不当。你可以检查一下硬盘的各根连线是否插好，看看同一根数据线上的两个硬盘的跳线的设置是否一样，如果一样，只要将两个硬盘的跳线设置的不一样即可(一个设为Master，另一个设为Slave)。
中文：检测从盘失败 解释：可能是CMOS设置不当，比如说没有从盘但在CMOS里设为有从盘，那么就会出现错误，这时可以进入COMS设置选择IDEHDDAUTODETECTION进行硬盘自动侦测。也可能是硬盘的电源线、数据线可能未接好或者硬盘跳线设置不当，解决方法参照第5条。 (s)fail或FloppyDisk(s)fail(80)或FloppyDisk(s)fail(40) 中文：无法驱动软盘驱动器。 解释：系统提示找不到软驱，看看软驱的电源线和数据线有没有松动或者是接错，或者是把软驱放到另一台机子上试一试，如果这些都不行，那么只好再买一个了，好在软驱还不贵。 (s)diagnosisfail 中文：执行硬盘诊断时发生错误。 解释：出现这个问题一般就是说硬盘本身出现故障了，你可以把硬盘放到另一台机子上试一试，如果问题还是没有解决，只能去修一下了。 中文：内存检测失败。 解释：重新插拔一下内存条，看看是否能解决，出现这种问题一般是因为内存条互相不兼容,去换一条吧！ 中文：当前CMOS设定无法启动系统，载入BIOS中的预设值以便启动系统。解释：一般是在COMS内的设定出现错误，只要进入COMS设置选择LOADSETUPDEFAULTS载入系统原来的设定值然后重新启动即可。
(完整word版)电脑常见硬件故障大全,推荐文档
电脑常见硬件故障大全 硬件故障是每个计算机用户都不愿意面对,却又不得不面对的一道“难题”。其实,解决这些问题并不一定需要非常高深的专业知识，小编为大家分享了电脑常见硬件故障大全，希望大家喜欢。 电脑常见硬件故障大全 Ⅰ、如果电脑无法开机，而且CPU风扇不转动，则有可能是电源有故障或者电源线没有接好。排除故障的方法：更换电源来排除故障。 Ⅱ、如果开机后电源指示灯亮，CPU风扇正常转动，但显示器无显示，无声响，那么就有一下两种可能： (1) CUP或内存接触不良。排除故障的方法：检查重新安装或更换CPU、内存条看是否能解除故障。 (2) 内存、PCI-e或PCI的工作频率与外频不相匹配，发生故障。故障排除方法：一般先进行CMOS放电把CMOS还原成默认设置(注意：放电时一定要把电源线拔出)。重新开机，再试试看看故
障是否排除。 Ⅲ、如果开机后，屏幕有反映，但是屏幕只显示一下黑屏和英文就停下来了即不能完成自检，那么就很可能是主板有故障。
Ⅳ、如果开机后，屏幕没有显示即完全不能自检，并伴有声响，那么可能是以下两种情况： a、伴有两长一短声时，很可能是显示卡接触不良。排除故障的方法：关闭主机电源后，松开显示卡金属挡板上的固定螺丝，插好后，再拧紧螺丝。然后开机，再试试。 b、伴有一长声，则可能是内存条未插好，关闭主机电源重新插好内存条。 Ⅴ、如果开机自检过程中，屏幕提示：“harddisknot present”或“Hard disk drive failure”或“Hard drive controller
failure”或类似信息，则可能是硬盘驱动器的硬件故障。排除故障的方法：可以通过检查硬盘的连接线、或更换硬盘、或者调整CMOS 设置。 Ⅵ、如果开机自检过程中，屏幕提示“Missing operating system”、“Non system disk or disk error”或类似信息，则很可能是硬盘主引导分区表被破坏或者是操作系统损坏。解决办法是：重新安装操作系统。
电脑开机出错英文提示翻译解释
电脑开机出错英文提示翻译解释 1.bat command or file name 错误语法，命令错误。 2.data error 数据错误磁盘上有坏的区 3.deacre asing available memory 可以存贮器容量小，内存条安装不正确，内存坏，病毒。 4.diskette read failvre 软盘读取错误，软盘软驱没有接好 5.hard disk config wration error 硬盘配置不对，coms有错重新修改，硬盘数据线没有连好。 6.inavlid fconfig uratian information 无效的配置信息，coms中记录有系统信息不对。 7.no bat device available 无引导设备 8.no boot sectoron harddisk error 硬盘上无引导系统，引导扇区，病毒，参数不对 9.nonsystem diskor disk error 非系统盘或者硬盘错误，引导的磁盘不是系统盘或者磁盘有问题。 10.invalid disk drive 无效的磁盘驱动器，分区表坏，引导扇区坏，系统不正硬 11.no fised disk resent 硬盘不存在 12.keybard keypressed please hit
电脑开机出错英文提示翻译解释
电脑开机出错英文提示翻译解释 bat command or file name 错误语法，命令错误。 data error 数据错误磁盘上有坏的区 deacre asing available memory 可以存贮器容量小，内存条安装不正确，内存坏，病毒。 diskette read failvre 软盘读取错误，软盘软驱没有接好 hard disk config wration error 硬盘配置不对，coms有错重新修改，硬盘数据线没有连好。inavlid fconfig uratian information 无效的配置信息，coms中记录有系统信息不对。 no bat device available 无引导设备 no boot sectoron harddisk error 硬盘上无引导系统，引导扇区，病毒，参数不对 nonsystem diskor disk error 非系统盘或者硬盘错误，引导的磁盘不是系统盘或者磁盘有问题。invalid disk drive 无效的磁盘驱动器，分区表坏，引导扇区坏，系统不正硬
no fised disk resent 硬盘不存在 keybard keypressed please hit
电脑常用故障英文及软件使用(希望对大家有帮助)
电脑常用故障英文及软件使用 电脑常用故障英文 1.CMOS battery failed 中文：CMOS电池失效。 解释：这说明CMOS电池已经快没电了，只要更换新的电池即可。 2.CMOS check sum error-Defaults loaded 中文：CMOS执行全部检查时发现错误，要载入系统预设值。 解释：一般来说出现这句话都是说电池快没电了，可以先换个电池试试，如果问题还是没有解决，那么说明CMOS RAM可能有问题，如果没过一年就到经销商处换一块主板，过了一年就让经销商送回生产厂家修一下吧！ 3. Press ESC to skip memory test 中文：正在进行内存检查，可按ESC键跳过。 解释：这是因为在CMOS内没有设定跳过存储器的第二、三、四次测试，开机就会执行四次内存测试，当然你也可以按ESC键结束内存检查，不过每次都要这样太麻烦了，你可以进入COMS设置后选择BIOS FEATURS SETUP，将其中的Quick Power On Self Test设为Enabled，储存后重新启动即可。 4.Keyboard error or no keyboard present 中文：键盘错误或者未接键盘。 解释：检查一下键盘的连线是否松动或者损坏。 5.Hard disk install failure 中文：硬盘安装失败。 解释：这是因为硬盘的电源线或数据线可能未接好或者硬盘跳线设置不当。你可以检查一下硬盘的各根连线是否插好，看看同一根数据线上的两个硬盘的跳线的设置是否一样，如果一样，只要将两个硬盘的跳线设置的不一样即可(一个设为Master，另一个设为Slave)。 6.Secondary slave hard fail 中文：检测从盘失败 解释：可能是CMOS设置不当，比如说没有从盘但在CMOS里设为有从盘，那么就会出现错误，这时可以进入COMS设置选择IDE HDD AUTO DETECTION进行硬盘自动侦测。也可能是硬盘的电源线、数据线可能未接好或者硬盘跳线设置不当，解决方法参照第5条。 7.Floppy Disk(s) fail或Floppy Disk(s) fail(80)或Floppy Disk(s) fail(40) 中文：无法驱动软盘驱动器。 解释：系统提示找不到软驱，看看软驱的电源线和数据线有没有松动或者是接错，或者是把软驱放到另一台机子上试一试，如果这些都不行，那么只好再买一个了，好在软驱还不贵。
电脑故障英文处理
CMOS battery failed CMOS电池失效。一般出现这种情况就是说明给主板CMOS供电的电池已经快没电了，需要朋友们及时更换主板电池。 CMOS check sum error-Defaults loaded CMOS执行全部检查时发现错误，要载入系统预设值。一般来说出现这句话有两种解释：一种是说主板CMOS供电电池快要没电了，朋友们可以先换个电池试试看；第二种解释是如果更换电池后问题还是没有解决，那么就说明CMOS RAM可能有问题了，如果主板没过一年的话就可以到经销商处换一块主板，要是过了一年就让经销商送回生产厂家修一下吧！ Floppy Disk(s) fail 或Floppy Disk(s) fail(80) 或Floppy Disk(s) fail(40) 无法驱动软盘驱动器。系统提示找不到软驱，首先要看看软驱的电源线和数据线有没有松动或者是接反，最好是是把软驱放到另外一台机子上试一试，如果这些都不行，那么只好再买一个了，好在目前市场中的软驱还不算贵。 Hard disk install failure 硬盘安装失败。这是因为硬盘的电源线或数据线可能未接好或者硬盘跳线设置不当引起的。朋友们可以检查一下硬盘的各根连线是否插好，看看同一根数据线上的两个硬盘的跳线设置是否一样。如果一样，只要将两个硬盘的跳线设置不一样即可(一个设为Master ，另一个设为Slave)。 Hard disk(s) diagnosis fail 执行硬盘诊断时发生错误。出现这个问题一般就是硬盘内部本身出现硬件故障了，你可以把硬盘放到另一台机子上试一试，如果问题还是没有解决，只能去修一下了。如果硬盘还在包换期内的话，最好还是赶快去换一块！ Hardware Monitor found an error，enter POWER MANAGEMENT SETUP for details，Press F1 to continue，DEL to enter SETUP 监视功能发现错误，进入POWER MANAGEMENT SETUP查看详细资料，或按F1键继续开机程序，按DEL键进入CMOS设置。现在好一些的主板都具备有硬件的监视功能，用户可以设定主板与CPU的温度监视、电压调整器的电压输出准位监视和对各个风扇转速的监视，当上述监视功能在开机时发觉有异常情况，那么便会出现这段话，这时朋友们可以进入CMOS设置选择POWER MANAGEMENT SETUP，在右面的**Fan Monitor**、**Thermal Monitor**和**Voltage Monitor**查看是哪部分监控发出了异常情况，然后再加以解决。 Keyboard error or no keyboard present 键盘错误或者未接键盘。检查一下键盘与主板接口是否接好，如果键盘已经接好，那么就是主板键盘口坏了，主板如尚在包修期内，朋友们可以找经销商或主板厂家进行解决。 Memory test fail 内存检测失败。重新插拔一下内存条，看看是否能解决，出现这种问题一般是因为混插的内存条互相不兼容而引起的，有条件的话去换一条吧！如果使用的只是一根内存条，那么就一定是内存条本身有问题，还是赶快去换一条的好！
计算机维修常用英语
计算机维修常用英语 对于维修人员，整天都在与故障机打交道，大多故障机会给出错误提示，根据提示我们可以最快的排查问题，但这些提示大多是英语，所以了解常用的计算机英语，对我们以后维修非常有帮助。 PC（Personal Computer，个人计算机） Microsoft: 有时缩略为MS，是全球最著名的软件商，美国软件巨头微软公司的名字。Microsoft其实是由两个英语单词组成：Micro意为“微小”，Soft意为“软的”，此处应为“Software，软件”，顾名思义，微软(Microsoft)是专门生产软件的公司。当今90％以上的微机都是装载Microsoft的操作系统，如MS－DOS 6.22、Windows 3.2、Windows 95、Windows NT等。 Intel：英特尔公司，是世界上最大的CPU(中央处理器，被人们称为电脑的心脏)及相关芯片制造商。80％左右的电脑都是使用Intel公司生产的CPU。其产品从早期的8088到目前流行的Pentium、Pentium Pro、Pentium MMX、Pentium Ⅱ等。 AMD：世界第二大CPU制造商。 Cyrix：CPU制造商，主要产品有M1，M2 MMX CPU系列。 Epson：爱普生，日本爱普生打印机制造商。 HP：惠普，Hewlett Packard的缩写，是美国著名的惠普打印机、电脑制造商。Canon：佳能，著名打印机商标。日本著名的佳能打印机制造商。Canon英文意思为“宗教法规，标准”，可以看出佳能公司在创业之初，就决心要把自己的产品作为业界的“标准”。Compaq：汉译为“康柏”，美国康柏电脑公司，它是世界上最大的电脑公司之一。 IBM：是International Business Machine Company(美国国际商用机器公司)的缩写。IBM是美国老牌电脑制造商，其产品是国际知名品牌。 Apple：英文为“苹果”之意，美国苹果电脑公司，该公司以生产高性能专业级电脑著称于世。 Acer：台湾著名的宏电脑公司。 Tulip：英语意思为“郁金香”，来自欧洲的名牌电脑商，郁金香电脑公司。 Sony：索尼，日本索尼公司。 Toshiba：东芝，日本东芝电脑公司，主要生产笔记本电脑。 Philips：飞利浦，荷兰飞利浦公司，主要生产彩显、光驱、家用电器等。 Sumsung：三星，韩国三星公司，著名的彩显制造商，也生产光驱、家用电器等。 IBM（International Business Machine，美国国际商用机器公司简称，最早 的个人计算机品牌） ） Pentium（Intel公司，X86 CPU芯片，中文译名为"奔腾"） IT（Information Technology，信息产业） E-Commerce Eelectronic Business（电子商务） B2C（Business To Customer，商家对顾客, 电子商务的一种模式，还有B2C 、C2C模式） Y2K（2k year，两千年问题，千年虫） IC（Integrate Circuit，集成电路）
电脑常见问题,英文翻译(Computer FAQ)
电脑常见问题,英文翻译（Computer FAQ） Computer FAQ This post is from the Internet to find some of the computer problems, here for your reference. A: the machine more and more slowly reasons There are a lot of people who say how slow their computers are and how slowly they actually make their computers slow! But I'm here to introduce the main reason for the slow computer! 1, loading too many programs at boot time 2. Open tablecloth on the tabletop 3, do not regularly clean the hard disk and the reorganization of hard disk Below, I'll explain in great detail how to speed up the computer and slow the symptoms of the computer! Solve the seven most common symptoms of computer performance. When the computer suddenly slows down, you may wonder if you did something wrong and cause damage to the computer In fact, don't worry too much, because a small change may affect the performance of computer operation, and in the process of using the computer, inevitably can cause a variety of minor changes. Any problem can be solved by any means, so let me elaborate the seven common causes that affect the performance of the computer. After solving them, we can enjoy the high performance of the computer.