管道工程中英文对照
工程管道英文缩写对照
A
A Anchor 固定
ABS Absolute 绝对的
AISI American Iron and Steel Institute 美国钢铁学会
ANSI American National Standards Institute 美国国家标准学会API American Petroleum Institute 美国石油学会
APPROX Approximate 大约，近似的
ASB Asbestos 石棉
ASME *American Society Of Testing Material 美国机械工程师协会ASSY *Assembly 装配，组装
ASTM *American Society Of
Testing Material 美国材料实验协会
ATM *Atmosphere 大气压
AWG *American Wire Gage 美国线规
AWS *American Wel**** Society 美国焊接协会
AWWA *American Water Works
Association 美国水工协会
B
BB Bolted Bonnet 栓柱连接的阀盖
BB By Buyer 买方供货
B-B Beveled End-Beveled End 两端为坡口端
BC Bolt Circle 螺栓中心圆
B.C Bolted Cover(cap) 螺栓连接的阀兰盖（帽）
BE Beveled End (for wel****) 坡口（焊接用）
B.E Bell End 承口
BEP Both Ends Plain 两端平
BET Both Ends Threaded 两端带螺纹
BL Battery Limit 装置区边界
BF Blind Flange 法兰盖
BLD Blind 盲板
BLDG *Buil**** 建筑物
BM Bill Of Material 材料表
BOP Bottom Of Pipe 管底
B-P Beveled End —Plain End 坡口端.平端
BV Butterfly valve 蝶阀
BWG * Birmingham Wire Gage 伯明翰线规
BW Butt Weld 对焊
C
C Cap 管帽
C-C Center to Center 中至中
C-E Center to End 中至端面
C-F Center to Face 中至面
CH-OP Chain Operated 链条操纵的
CH.PL Checkered Plate 花纹钢管
C.I *Cast Iron 铸铁
CL *Class 英制压力等级，等级，种类CLEAR Clearance 间隙
COD Continued on Drawing 接续图
COL *Column 柱，塔
CONC Concentric 同心的
CONN Connection 连接，接口
CONT *Continue 连续
CONT.V. Control Valve 控制阀
CPLG Coupling 管接头，连轴节
C.R. Concentric Reducer 同心异径管
C.S. *Carbon Steel 碳钢
C.S. Cold Spring 冷紧
C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客
C.V Check Valve 止回阀
D
DEG *Degree 度
DF Drain funnel 排液漏斗
DIA *Diameter 直径
DIM *Dimension 尺寸
DISCH *Discharge 出口，排出Diaphragm VELVE 隔膜阀
DMF Double Male And Female 双重凹凸DN *Double Male And Female 公称直径DN Down 下
DR Drain 排液
DS Directional Stop 定向限为架
DWG *Drawing 图
E
E *East 东
EC External Coating 外面涂防腐层
ECC Eccentric 偏心
EFW Electric Fusion Welded 电容焊的
EL(ELEV) *Elevation 标高；立面
ELL Elbow 弯头
EQIOP Equipment 设备，装置
EQUIV Equivalent 相当的
E.R. Eccentric Reducer 偏心异经管
ERW Electric Resistance Welded 电阻焊的EW Eye Washer & Shower 洗眼器及淋浴器EXP.JT Expansion Joint 膨胀节
F
FDN Foundation 基础
FF Flat Faced Or Full Faced 全平面；满平面
F-F Face To Face 面至面
FGW Fusion Gas Wel**** 气熔焊
FIG *Figure 图
FL Floor 楼面
FLEX TUBE Flexible Tube 挠性管
FLG Flange 法兰
FLGD Flanged 法兰式的
FLGF Flanged Face 法兰面
FOB Flat On Bottom 底面平
FOT Flat On Top 顶面平
FP Fix Point 固定点
FS Forged Steel 锻钢
FTF Fitting To Fitting 管件直连
FTG Fitting 管件
FURND Furnished 提供的，装设的
FW Field Weld 现伤焊
G
G Guide 导向
GA *Gage 表，表压，规（线规）
GALV *Galvanize 镀锌
GL Ground Level 地面
GLV Globe Valve 截止阀
GEAR OP Gear Operated 齿轮传动的
GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊
GSKT Gasket 垫片
GTAW (Inert)Gas Tungsten Arc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀
H
H Hanger 吊架
HC Hose Connection 软管接头
H.CPLG Half Coupling 半节管接头
HDR Header 总管
HEX *Hexagon 六角形
HF Hard Alloy Face on阀内件（阀心）为
Valve Trim 硬质合金密封面
HH Hand Pole 手孔
HOR Horizontal 水平的
H.P *High Pressure 高压
HS Hose Station 软管
I
ID *Inside Diameter 内径
IN *Inch 英寸
INS Insulation 隔热
INST Instrument 仪表
INV Invert (inside bottom of pipe) 管子内底
IPS Iron Pipe size 铁管尺寸
ISO Isometric Drawing 周测图（空视图）
I.S.B.L Inside Battery Limit 装置边界内恻
ISNS Inside screw & Non-rising Stem 内螺纹非升杆
ISRS Inside screw & Rising stem 内螺纹升杆
J
JT Joint 接头
JS Jack Screw 顶开（起）螺栓
L
LC Locked Closed 在关闭状态下锁定
LEP Large end plain 大端为平的
LET Large end Threaded 大端带螺纹
LG Long 长
LGF Lens Gasket Face 透镜垫连接面
L.H.THD Left Hand Thread 左螺纹
LIFT Lift Type 升降式
LJ Lap Joint 搭接
LJF Lap Joint Flange 松套法兰
LO Locked Open 在开启状态下锁定
L.P. Low Pressure 低压
LR Long Radius 长半径
LRE Long Radius Elbow 长半径弯头
LTG Large Tongue & Groove 大椎槽
M
MATL Material 材料
MAX Maximum 最大
MB Machine Bolt 机器螺栓（单头）
MF Male and Female 凸和凹
MFG Manufacture 制造
MF *Manufacture 制造厂
MH Manhole 人孔
MI Malleable Iron 可锻铸铁
MIN *Minimum 最小
MJ Mechanical Joint 机械接头
M.L Match Line 连续线
MSS * Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.美国阀门和管件制造商标准化协会
MTO Material take-off 材料统计
MW Minimum Wall 最小壁厚
M.W. Mineral Wool 矿（物）棉
N
N *North 北
NB Nominal Bore 公称孔径
N.B. Non-Bonnet 无阀盖
NC Normally Closed 常闭
NIP Nipple 短管
NO Normally Open; 常开
*Number号；数量
NO INS No Insulation 不隔热
NOM Nominal 公称的；额定的
NOZ Nozzle 管口
NPS Nominal Pipe Size 公称管径
NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹
Pipe Thread
NS Nominal Size 公称直径
NV Needle Valve 针形阀
O
OD *Outside Diameter 外径
OET One end Threaded 一端带螺纹
OR Outside Radius 外半径
ORF Orifice 孔板
ORIENT Orientation 方位
OS & Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖
P
P Plug 堵头
PAP Piping Arrangement Plan 管道布置平面图
PB Pressure Seal Bonnet 压力密封的阀盖
P-B Plain End –Bevel End 平端—坡口端
PC Pressure Seal Cap 压力密封的阀帽
P.C.D. Pitch Circle Diameter 节圆直径
PE Plain End (not beveled) 平端（无坡口）
PF Platform 平台
PID Piping & Instrument Diagram管道及仪表流程图PN *Nominal Pressure 公称压力
PN Plant North 工厂北向
POS point of Support 支承点
P-P Plain End—Plain End 两端为平端
PREP Preparation 加工准备
PSIA *Pounds Per Square Inch
Absolute 磅/
PSIG Pounds Per Square Inch Gage 磅/
PT Point 点
PTFE *Polytetrafluoroethylene 聚四氟乙烯
PT.NO Part No. 件号
PV Plug Valve 旋塞阀
PVC *Poly Vinyl Chloride 聚氯乙烯
Q
QTY *Quantity 数量
R
R *Radius 半径
RED Reducer 异径管
REF Reference 参考
REINF Reinforce 加强
REQD Required 需要；申请
REV *Revision 修改
RF Raised Face 凸面
RG Ring Gasket 环形垫片
R.H.THD Right Hand Thread 右螺旋
RJ Ring Joint 环垫接头
RO Restriction Orifice 限流孔板
RPM *Revolutions Per Minute 转/分
RPS *Revolutions Per Second 转/秒
RS Resting Support 支承架，滑动架
RTJ Ring Type Joint（见RJ）
RV Relief Valve 安全泄液阀
S
S *South 南
S Spring 弹簧（管架用）
SAW (Automatic)Submerged Arc Wel**** 自动埋弧焊SB Stud Bolt 双头螺栓
SB Screwed Bonnet 螺纹阀盖
SC Sample Cooler 取样冷却器
SCH *Schedule 管壁厚系列号
SCRD Screwed 螺纹
SEP Small end Plain 小端为平的
SET Small end Threaded 小端带螺纹
SF Semi-Finished 半光
SG Sight Glass 视镜
SH Surface Hard Facing 硬质密封面
SK Sketch 草图
SMAW Shielded Metal Arc Wel**** 有保护的金属电弧焊SMLS Seamless 无缝
SN Swaged Nipple 异径短管
SO Slip – On 滑套
SOF Slip – On Flange 滑套法兰
SPEC *Specification 规定，说明
SPL Sound Pressure Lever 升压水准SQ *Square 方的，平方
SR Shout Radius 短半径
SRE Short Radius Elbow 短半径弯头SS *Stainless Steel 不锈钢
ST Steam Trap 蒸汽疏水阀
STD *Standard 标准
STG Small Tongue & Groove 小椎槽面STL *Steel 钢
STM Steam 蒸汽
STM.TR Steam Tracing 蒸汽拌热SUCT Suction 吸入口
SV Safety Valve 安全泄气阀
SW Socket Weld 承插焊
SWG Swage 锻造，模锻
SWMG Swing Type 旋启式
SYM Symmetrical 对称的
T
T Tee 三通
TE Threaded End 螺纹端
TEMP *Temperature 温度
TG Tongue & Groove 椎槽
THD *Threaded 螺纹的
THK *Thickness 厚度
TL Tangent Line 切线
TN True North 真实北向
TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶
TOS Top of Support 支架顶面
Top of Steel 钢结构顶面
TYP Typical 典型的
U
UB Union Bonnet 带活接头的阀盖UC Union Cap 带活接头的阀帽
UN Union 活接头
V
V Valve 阀
VAC Vacuum 真空
VAR Variable 可变的
VERT Vertical 垂直的
VOL *Volume 卷，册，容量，体积W
W *West 西
WB Weld Branch 焊接支管
WC Weld Cap 焊接管帽
WD Width 宽度
WE Weld End 焊接端
WL Wel**** Line 焊接线
WN Wel**** Neck 对焊法兰（颈部）WNF Weld Neck Flange 对焊法兰
WP Working Pressure 工作压力
W.P. Working Point 工作点
WT Wall Thickness 壁厚
Weight 重量
X
XH Extra Heavy 加强的，加厚的
XXH Double Extra Heavy 双倍加强（厚）的XS Extra Strong 加强的
XXS Double Extra Strong 双倍加强的
Y
YP Yield Point 屈服点
管道专业术语常用英语单词
管道专业术语常用英语 单词 Document number：BGCG-0857-BTDO-0089-2022
管道专业术语常用英语单词 在引进装置、涉外及中外合资技术改造工程的技术资料中，经常要接触到英语单词。由于管道安装涉及多项工程技术，而不从属于任何一项工程技术分支，故其技术性质有一定特殊性，不少英语词汇是在实践中逐渐形成的，借助一般科技英汉词典有时也难以找到它们的确切含意。现将管道安装工程中出现较多的单词整理列出，如果能熟悉这些单词，对阅英文图纸能收到事半功倍的效果。 一、专业名词术语 设计图 施工图 平面图 立面图 轴测图、透视图 详图、大样图、接点图 修改图竣工图图名 图号 比例 温度 设计温度 湿度 流量 流速 摄氏温度ayout； design final plan elevation isometric drawing；detail drawing record drawing as-completed drawing； as-built drawing title drawn No. scale temperature design temperature humidity flow flow velocity ? ? 毛重 净重 支座 支架 吊架 间距 跨距 焊接 焊缝 石棉水泥 接口 青铅接口 承口、大 头 插口、小 头 压力试验 水压试验 gross weight net weight saddle support cradle distance； clearance； spacing span welding weld； welding seam； bead asbestos-cement joint lead joint hub； bell； socket spigot pressure test hydraulic test
印刷中英文术语对照
印刷中英文术语对照 Woodfree paper 書紙 Matt paper 啞粉紙 Glossy paper 光粉紙 1.GSM与LBS( pound)的转换： English paper grade to grammage conversion Grammage Paper Grade (LBS.) 44 gsm 30 lb. text 59 gsm 16 lb. bond, 40 lb. text 67 gsm 45 lb. text 89 gsm 24 lb. bond, 60 lb. text 104 gsm 70 lb. text 118 gsm 80 lb. text 148 gsm 67 lb. bristol, 100 lb. text 162 gsm 60 lb. cover 163 gsm 90 lb. index 176 gsm 65 lb. cover 178 gsm 80 lb. bristol 199 gsm 110 lb. index 216 gsm 80 lb. cover 219 gsm 100 lb. bristol 253 gsm 140 lb. index 263 gsm 120 lb. bristol
270 gsm 100 lb. cover 307 gsm 140 lb. bristol 308 gsm 170 lb. index 325 gsm 120 lb. cover 2.印刷品中英文对照 日历：calendar 台历：desk calendar 挂历：wall calendar 精装书: Case bound, hard bound, cloth bound, hardback, hardcover book 小册子:brochure 纸相架:Paper frame 纸板书: Board book 纸匣: paper tray 螺旋簿: spiral book 合订本：bound book 书芯纸印的封面。小册子的所有纸张（包括封面）采用同一类或相同克重的纸张，称为简装本（self-cover brochure）。 翻页书: flipbook 3.纸张中英文对照 铜版纸,又称涂布印刷纸:Coated Art Paper(or Board), Coated Woodfree; Art paper;Art printing pape;Copper printing paper 双铜纸: both sides coated art paper 亚粉纸: dull finished art paper,matt art paper
软件工程关键术语中英文对照表
课程关键术语中英文对照表 1、Software 软件 2、U ser 用户 3、s oftware engineering 软件工程 4、D ocument 文档 5、D ata 数据 6、S oftware Crisis 软件危机 7、S oftware Engineering 软件工程 8、M aintenance 维护 9、B ug 故障 10、Correctness 正确性 11、Reliability 可靠性 12、IDE 集成开发环境 13、Maintainability 可维护性 14、Reusability 可重用性 15、Traceability 可跟踪性 16、Portability 可移植性 17、Interoperability 互操作性 18、Efficiency 有效性 19、Abstract 抽象 20、Modularity 模块化 21、Information Hiding 信息隐藏
23、Consistency 一致 24、Completeness 完整 25、Verifiability 可验证 26、Software Lifecycle 软件生命周期 27、Feasibility Investigation 可行性分析 28、Requirement 需求 29、Requirement Analysis 需求分析 30、Software Delivery 软件发布 31、Prototype 原型 32、Software Requirement Specification (SRS) 软件需求规格说明书 33、Software Architecture 软件体系结构 34、software development 软件开发 35、unit testing 单元测试 36、Integration Test Plan 集成测试计划 37、Detailed Design 详细设计 38、Unit Test Plan 单元测试计划 39、Integration Test 集成测试 40、Integration Test Report 集成测试报告 41、Software Process 软件过程 42、Software Process Model 软件过程模型 43、Incremental Model 增量模型
管道零件英文缩写
1管子及管件 1.1 P 管子Pipe 钢管的厚度在10mm以上的都称之为厚壁埋弧焊管埋弧焊的英文标识为SAW, 直缝埋弧焊钢管的简称为LSAW, 螺旋埋弧焊钢管为SSAW LSAW 钢管Longitudinally Submerged Arc Welding Steel Pipe 直缝双面埋弧焊钢管，它是利用埋弧焊技术生产的直缝钢管。 SAW 钢管全称Submerged Arc Welding Steel Pipe 埋弧焊钢管 螺旋缝埋弧焊钢管 1.2 EL 弯头Elbow 1.2.1 ELL 长半径弯头Long radius elbow 1.2.2 ELS 短半径弯头Short radius elbow 1.2.3 MEL斜接弯头（虾米腰弯头）Mitre elbow 1.2.4 REL 异径弯头Reducing elbow 1.3 T 三通Tee 1.3.1 LT 斜三通Lateral tee 1.3.2 RT 异径三通Reduci ng tee 1.4 R异径管接头（大小头）Reducer 1.4.1 CR 同心异径管接头（同心大小头）Concentric reducer 1.4.2 ER偏心异径管接头（偏心大小头）Eccentric reducer 1.5 CPL 管箍Coupling 1.5.1 FCPL 双头管箍Full coupling 1.5.2 HCPL 单头管箍Half coupling 1.5.3 RCPL 异径管箍Reducing coupling 1.6 BU内外螺纹接头Bushing
1.7 UN 活接头Un ion 1.8 HC 软管接头Hose coupler 1.9 SE 翻边短节Stub end 1.10 NIP 短节Pipe nipple or straight nipple 1.10.1 SNIP 异径短节Swaged n ipple 1.11 CP管帽（封头）Cap 1.12 PL管堵（丝堵）Plug 1.13 BLK 盲板Blank 1.13.1 SB 8 字盲板Spectacle blind （blank） 1.14 RP 补强板Reinforcing pad 支管台（或称加强管接头OLET 加强管接头（OLET ）的选用：当支管直径50＜DNC 200,选用不到标准三通时，应采用加强管接头连接。 pipe管线类型,saw 是埋弧焊管，LGS是管道材料Longitudinal Seam 的缩写直缝焊管，PE是这防腐类型是PE结构 是不是PE , BE，与你的焊接工艺WPS有关。如果是插焊、壁厚薄，就用PE; I - 如果对焊且壁厚较厚，那就要打坡口弄成BE。 45ELB : 45度弯头、CAP :管帽、COUPLING :管箍、PLUG :管塞、REDC:同心异径管、R-TEE :异径三通、S-OLET :承插支管台、TEE:三通、T-OLET :螺纹支管台、UNION 活接头、W-OLET :焊接支管台。 20# GB8163-99 SCH80 SMLS.GALVH 和20# GB8163-99 SCH80 SMLS ; 前者比后者多了GALVH，这是热镀锌的意思。前边的是热镀锌的，后边的是不镀锌的。 CAP —帽、盖、COUPLING —耦合、PLUG —叉栓、R-TEE —R形三通管 ------- Reducer 一般指＞=2",两端对接焊口，swage 一般指＜2",两端可以是不同接头，如对接焊口，插入焊口，或者螺纹接头 swage 一般指异径管短节 swage 禾口reducer 各有同心cone,偏心ecc 两种 PIPE,SAW 丄GS BE GB/T 9711 PSL1 GB713 Q245R SH/T 3405 100%RT,ANTI-H2S 10MM PIPE :管道
软件工程复习资料-英文
Lecture 1 An Introduction to Software Engineering 1 what does software engineering concern? 1) Software engineering is concerned with theories, methods and tools for professional software development. 2) Software engineering is concerned with cost-effective software development. 2 What is software? Software includes: ①computer programs ②data structures ③documents 3 What is the two types of software products Generic software(通用软件) and custom software（定制软件） 4 The three key elements of a successful software project are: on time, within budget, satisfies the user’s needs 5 Generic activities in all software processes are: Specification（描述）, Development（开发）, Validation（有效性验证）, Evolution （进化） 6 The attributes of good software include: Maintainability（可维护性）, Dependability（可依赖性）, Efficiency（有效性）, Acceptability（可接受性）
管道及配件中英文对照
管道及配件中英文对照 化工管道词汇翻译 1.1管子Pipe 管子(按照配管标准规格制造的) pipe 管子(不按配管标准规格制造的其他用管) tube 钢管steel pipe 铸铁管cast iron pipe 衬里管lined pipe 复合管clad pipe 碳钢管carbon steel pipe 合金钢管alloy steel pipe 不锈钢stainless steel pipe 奥氏体不锈钢管austenitic stainless steel pipe 铁合金钢管ferritic alloy steel pipe 轧制钢管wrought-steel pipe 锻铁管wrought-iron pipe 无缝钢管seamless (SMLS) steel pipe 焊接钢管welded steel pipe 电阻焊钢管electric-resistance welded steel pipe 电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe
螺旋焊接钢管spiral welded steel pipe 镀锌钢管galvanized steel pipe 热轧无缝钢管hot-rolling seamless pipe 冷拔无缝钢管cold-drawing seamless pipe 水煤气钢管water-gas steel pipe 塑料管plastic pipe 玻璃管glass tube 橡胶管rubber tube 直管run pipe; straight pipe 1.2管件Fitting 弯头elbow 异径弯头reducing elbow 带支座弯头base elbow 长半径弯头long radius elbow 短半径弯头short radius elbow 长半径180°弯头long radius return 短半径180°弯头short radius return 带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand) 双支管弯头（形）double branch elbow 三通tee 异径三通reducing tee
管道零件英文缩写
1 管子及管件 1.1P 管子 Pipe 钢管的厚度在10mm以上的都称之为厚壁埋弧焊管 埋弧焊的英文标识为SAW, 直缝埋弧焊钢管的简称为LSAW, 螺旋埋弧焊钢管为SSAW LSAW 钢管 Longitudinally Submerged Arc Welding Steel Pipe 直缝双面埋弧焊钢管，它是利用埋弧焊技术生产的直缝钢管。 SAW钢管全称 Submerged Arc Welding Steel Pipe 埋弧焊钢管 螺旋缝埋弧焊钢管 1.2 EL 弯头 Elbow 1.2.1 ELL 长半径弯头 Long radius elbow 1.2.2 ELS 短半径弯头 Short radius elbow 1.2.3 MEL 斜接弯头（虾米腰弯头） Mitre elbow 1.2.4 REL 异径弯头 Reducing elbow 1.3 T 三通 Tee 1.3.1 LT 斜三通 Lateral tee 1.3.2 RT 异径三通 Reducing tee 1.4 R 异径管接头（大小头） Reducer 1.4.1 CR 同心异径管接头（同心大小头） Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头） Eccentric reducer 1.5 CPL 管箍 Coupling 1.5.1 FCPL 双头管箍 Full coupling 1.5.2 HCPL 单头管箍 Half coupling 1.5.3 RCPL 异径管箍 Reducing coupling 1.6 BU 内外螺纹接头 Bushing
1.7 UN 活接头 Union 1.8 HC 软管接头 Hose coupler 1.9 SE 翻边短节 Stub end 1.10 NIP 短节 Pipe nipple or straight nipple 1.10.1 SNIP 异径短节 Swaged nipple 1.11 CP 管帽（封头） Cap 1.12 PL 管堵（丝堵） Plug 1.13 BLK 盲板 Blank 1.13.1 SB 8字盲板 Spectacle blind (blank) 1.14 RP 补强板 Reinforcing pad 支管台（或称加强管接头OLET 加强管接头(OLET)的选用:当支管直径50≤DN≤200,选用不到标准三通时,应采用加强管接头连接。 pipe 管线类型 ,saw 是埋弧焊管，LGS是管道材料Longitudinal Seam 的缩写直缝焊管，PE是这防腐类型是PE结构 是不是PE，BE，与你的焊接工艺WPS有关。 如果是插焊、壁厚薄，就用PE； 如果对焊且壁厚较厚，那就要打坡口弄成BE。 45ELB : 45度弯头、CAP：管帽、COUPLING：管箍、PLUG：管塞、REDC：同心异径管、R-TEE：异径三通、S-OLET：承插支管台、TEE：三通、T-OLET：螺纹支管台、UNION：活接头、W-OLET：焊接支管台。 20# GB8163-99 SCH80 SMLS.GALVH和20# GB8163-99 SCH80 SMLS；前者比后者多了GALVH，这是热镀锌的意思。前边的是热镀锌的，后边的是不镀锌的。 CAP—帽、盖、COUPLING—耦合、PLUG—叉栓、R-TEE—R形三通管 Reducer一般指>=2",两端对接焊口，swage一般指<2",两端可以是不同接头，如对接焊口，插入焊口，或者螺纹接头 swage一般指异径管短节 swage和reducer 各有同心conc,偏心ecc两种 PIPE,SAW,LGS BE GB/T 9711 PSL1 GB713 Q245R SH/T 3405 100%RT,ANTI-H2S 10MM
软件工程中英文对照外文翻译文献
中英文对照外文翻译 (文档含英文原文和中文翻译) Application Fundamentals Android applications are written in the Java programming language. The compiled Java code — along with any data and resource files required by the application — is bundled by the aapt tool into an Android package, an archive file marked by an .apk suffix. This file is the vehicle for distributing the application and installing it on mobile devices; it's the file users download to their devices. All the code in a single .apk file is considered to be one application. In many ways, each Android application lives in its own world: 1. By default, every application runs in its own Linux process. Android starts the process when any of the application's code needs to be executed, and shuts down the process when it's no longer needed and system resources are required by other applications. 2. Each process has its own virtual machine (VM), so application code runs in isolation from the code of all other applications. 3. By default, each application is assigned a unique Linux user ID. Permissions are set so that the application's files are visible only to that user and only to the application itself — although there are ways to export them to other applications as well. It's possible to arrange for two applications to share the same user ID, in which case they will be able to see each other's files. To conserve system resources, applications with the same ID can also arrange to run in the same Linux process, sharing the same
管道方案(中英文对照版)
管道工程施工质量管理工作细则 PIPING CONSTRUCTION QUALITY MANAGEMENT DETAIL RULES 目录 Content 1.0 编制目的及适用范围 Purpose for Preparation and Scope of Application 2.0 编制原则 Principles for Preparation 3.0执行标准及有关规定 Applicable Standards and Relevant Regulations 3.1 中国政府的相关法规和政策 Relevant laws, regulations and policies issued by Chinese government: 3.2 SECCO项目IPMT质量体系有关文件 Documentation related to IPMT quality system of SECCO project: 3.3 SECCO项目IPMT规定和要求 IPMT regulations and requirements of SECCO project: 3.4 施工验收标准及规范 Standards and codes for construction acceptance: 4.0 冲突和协调 Conflict and Coordination 5.0 专业技术经理与专业工程师 Specialist Technical Manager and Specialist Engineer 5.1专业技术经理 Specialist technical manager 5.2 专业工程师 Specialist engineer 6.0 HSE 7.0 施工过程中工程施工质量的控制 Quality Control in the Process of Construction
印刷专业用语(中英)
印刷专业用语 纸料： 260g粉灰260g grey back MC board 300g粉灰300g grey back MC board 350g粉灰350g grey back MC board 350g单粉咭(白芯/灰芯)350g single side coated board (white liner/grey liner) 350g双粉咭(白芯/灰芯)350g both sides coated board (white liner/grey liner) 80g书纸80g W/F PAPER 80g色书纸80g color W/FPAPER 157g双粉纸157g art paper 157g哑粉纸157g matt coated paper 防潮纸Moisture Proof paper 铜板不干胶Raflacoat self-adhesive 双铜纸glossy paper/ coated art paper 双胶纸offset paper 轻涂纸Light Weight Coated Paper 无光铜版纸matt art paper 光面铜版纸gloss paper 灰底白板卡纸CCNB的全称是Clay Coated News Back 牛底白板纸板CCKB(Clay Coated Kraft Back) 白底灰芯纸板CCWB(Clay Coated White Back)
铜板卡纸/白芯粉咭SBS(Solid Bleached Sulphate) 合成纸Synthetic paper 根据表面涂布情况SBS又分为单粉咭C1S(coated one side)和双粉咭 C2S(coated two sides)。根据表面涂布效果分为Matte(哑光纸)和Glossy(光面纸)。 坑纸: BEE-flute (125g牛咭+110g芯纸) WE-flute (140g白牛咭+110g芯纸) B3-flute (125g牛咭+115g芯纸) A3-flute (175g牛咭+115g芯纸) K3-flute (250g牛咭+115g芯纸) W3-flute (140g白牛咭+115g芯纸) A3B9-flute (175g牛咭+115g芯纸+125g牛咭+110g芯纸)K3B9-flute (250g牛咭+115g芯纸+125g牛咭+110g芯纸)印刷 印油Transparent ink 印光油Gloss Varnishing 印哑油Matt Varnishing 印专色Printed in spot color 表面处理 磨光Calendaring 磨光吸塑油Blister-calendaring varnish 过光油Varnishing
软件工程第八版(英文)机械工业出版社 课后习题
Part 1 Overview Chapter 1 Introduction 1.1 FAQs about software engineering 1.2 Professional and ethical responsibility Chapter 2 Socio-technical systems 2.1 Emergent system properties 2.2 Systems engineering 2.3 Organisations, people and computer systems 2.4 legacy systems Chapter 3 Critical systems 3.1 A simple safety-critical system 46 3.2 System dependability 47 3.3 Availability and reliability 51 3.4 Safety 55 3.5 Security 58 Chapter 4 Software processes 4.1 Software process models 65 4.2 Process iteration 71 4.3 Process activities 74 4.4 The Rational Unified Process 82 4.5 Computer-Aided Software Engineering 85 Chapter 5 Project management 92 5.1 Management activities 94 5.2 Project planning 96 5.3 Project scheduling 99 5.4 Risk management 104 Requirements Chapter 6 Software requirements 6.1 Functional and non-functional requirements 6.2 User requirements 6.3 System requirements 6.4 Interface specification 6.5 The software requirements document Chapter 7 Requirements engineering processes 7.1 Feasibility studies 7.2 Requirements elicitation and analysis 7.3 Requirements validation 7.4 Requirements management Chapter 8 System models 8.1 Context models 8.2 Behavioural models 8.3 Data models 8.4 Object models 8.5 Structured methods Chapter 9 Critical systems specification 9.1 Risk-driven specification 9.2 Safety specification 9.3 Security specification 9.4 Software reliability specification Chapter 10 Formal specification 10.1 Formal specification in the software process 10.2 Sub-system interface specification 10.3 Behavioural specification Part 3 Design Chapter 11 Architectural design 11.1 Architectural design decisions 11.2 System organisation 11.3 Modular decomposition styles 11.4 Control styles 11.5 Reference architectures Chapter 12 Distributed systems architectures 12.1 Multiprocessor architectures 12.2 Client-server architectures 12.3 Distributed object architectures 12.4 Inter-organisational distributed computing Chapter 13 Application architectures 13.1 Data processing systems 13.2 Transaction processing systems 13.3 Event processing systems 13.4 Language processing systems Chapter 14 Object-oriented design 14.1 Objects and object classes 14.2 An object-oriented design process 14.3 Design evolution Key Points Further Reading Exercises Chapter 15 Real-time software design
管件标准中英文对照
管件标准中英文对照 Standard Code 规范代号 Standard Name 规范名称 ASME SA-234 中、高温用钢制碳钢和合金钢管道配件 Medium and high temperature used carbon and alloy steel pipe fittings ASME SA-420 低温用锻制碳钢和合金钢管配件 Low temperature forged carbon and alloy steel pipe fittings ASME SA-403 锻制奥氏体不锈钢管配件 Forged Durimet pipe fittings ASME B16.9 工厂制造的钢制对焊管件 Factory-Made wrought steel pipe fittings ASME B16.11 承插焊和螺纹锻钢管件 Socket-welding and Threaded forged fittings ASME B16.28 锻钢对焊小半径弯头和回弯头 Wrought steel butt-welding short radius elbows and returns ISO 5251 不锈钢对焊管件 Stainless steel butt-welding fittings MSS SP-43 锻制不锈钢对焊管件 Wrought stainless steel butt-welding fittings MSS SP-75 锻钢制对焊管件 Forging butt-welding fittings MSS SP-79 承插焊异径插入件 Socket-welding reducing Inserts MSS SP-83 3000磅级的钢制承插焊和螺纹活接头 Class 3000 steel socket-welding and threaded unions MSS SP-95 缩渐管和圆堵头 Swaged nipples and round plugs MSS SP-97 承插焊、螺纹和对焊端的整体加紧式管座 SW 、TH and BW ends for integrally reinforced forged branch outlet JIS B2311 通用钢制对焊管件 Universal steel butt-welding pipe fittings JIS B2312 钢制对焊管件 Steel butt-welding pipe fittings JIS B2313 钢板制对焊管件 Steel plate butt-welding pipe fittings JIS B2316 钢制承插焊管件 Steel socket-welding pipe fittings DIN 2605 钢制对焊管件弯头和弯管 Steel butt-welding pipe fittings.elbows and bends DIN 2615 钢制对焊管件三通 Steel butt-welding pipe fittings.tees DIN 2616 钢制对焊管件异径管 Steel butt-welding pipe fittings.reducers
常见职务中英文对照版
常见职务，职位英文译名 Accounting Assistant 会计助理 Accounting Clerk 记帐员 Accounting Manager 会计部经理 Accounting Stall 会计部职员 Accounting Supervisor 会计主管 Administration Manager 行政经理Administration Staff 行政人员 Administrative Assistant 行政助理Administrative Clerk 行政办事员 Advertising Staff 广告工作人员 Airlines Sales Representative 航空公司定座员Airlines Staff 航空公司职员 Application Engineer 应用工程师 Assistant Manager 副经理 Bond Analyst 证券分析员 Bond Trader 证券交易员 Business Controller 业务主任 Business Manager 业务经理 Buyer 采购员 Cashier 出纳员 Chemical Engineer 化学工程师 Civil Engineer 土木工程师 Clerk/Receptionist 职员/接待员 Clerk Typist & Secretary 文书打字兼秘书Computer Data Input Operator 计算机资料输入员Computer Engineer 计算机工程师 Computer Processing Operator 计算机处理操作员Computer System Manager计算机系统部经理Copywriter广告文字撰稿人 Deputy General Manager副总经理 Economic Research Assistant经济助究助理Electrical Engineer电气工程师 Engineering Technician工程技术员 English Instructor/Teacher英语教师 Export Sales Manager外销部经理 Export Sales Staff外销部职员 Financial Controller财务主任 Financial Reporter财务报告人 F.X. (Foreign Exchange)Clerk外汇部职员 F.X. Settlement Clerk外汇部核算员 Fund Manager财务经理 General Auditor审计长 General Manager/ President总经理 General Manager Assistant总经理助理 General Manager's Secretary 总经理秘书
管材、管件、阀门、接头、管道特件、紧固件、密封等中英文对照
管材、管件、阀门、接头、管道特件、紧固件、垫片、密封、工程材料等中英文对照 化工管道设计技术英语词汇(1－2－3) 1 管道组成件 Piping component 1.1 管子 Pipe 管子(按照配管标准规格制造的) pipe 管子(不按配管标准规格制造的其他用管) tube 钢管 steel pipe 铸铁管 cast iron pipe 衬里管 lined pipe 复合管 clad pipe 碳钢管 carbon steel pipe 合金钢管 alloy steel pipe 不锈钢 stainless steel pipe 奥氏体不锈钢管 austenitic stainless steel pipe 铁合金钢管 ferritic alloy steel pipe 轧制钢管 wrought-steel pipe 锻铁管 wrought-iron pipe 无缝钢管 seamless (SMLS) steel pipe 焊接钢管 welded steel pipe 电阻焊钢管 electric-resistance welded steel pipe 电熔（弧）焊钢板卷管 electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管 spiral welded steel pipe 镀锌钢管 galvanized steel pipe 热轧无缝钢管 hot-rolling seamless pipe 冷拔无缝钢管 cold-drawing seamless pipe 水煤气钢管 water-gas steel pipe 塑料管 plastic pipe 玻璃管 glass tube 橡胶管 rubber tube 直管 run pipe; straight pipe 1.2 管件 Fitting 弯头 elbow 异径弯头 reducing elbow 带支座弯头 base elbow k半径弯头 long radius elbow 短半径弯头 short radius elbow 长半径180°弯头 long radius return 短半径180°弯头 short radius return 带侧向口的弯头（右向或左向） side outlet elbow (right hand or left hand) 双支管弯头（形） double branch elbow
包装印刷中英文专业术语大全
包装印刷中英文专业术语大全 刀版die plate 菲林printing film/artwork 数码印刷digital printing 印前工序prepress process 包装种类 包装盒 packaging 天地盖盒lid and base box 彩盒color printing box 储物盒storage box 展示盒display stand 翻盖盒/可折叠盒folding paper box 珠宝盒Jewelry box 茶叶盒tea box 鞋盒shoe box 盒Box 纸盒 paper box 硬纸盒rigid paper box 瓦楞纸盒corrugated paper box 木盒Wooden Box 铁盒Iron Box 塑料透明盒 Plastic Transparency Box 苯乙烯盒 Styrol Box 礼盒presentation box 礼品盒gift box 展示盒showing box
箱Case 纸箱Carton 外箱master carton 瓦椤纸箱Corrugated Carton 旧瓦椤纸箱Old Corrugated Carton (O．C．C．) 木箱Wooden Case 板条箱Crate 木条箱Wooden Crate 竹条箱Bamboo Crate 胶合板箱Plywood Case 三层夹板箱3--Ply Plywood Case 镀锡铁皮胎木箱Tin Lined Wooden Case 集装箱Container 袋Bag(Sack) 布袋Cloth Bag 草袋Straw Bag 麻袋Gunny Bag／Jute Bag 旧麻袋Used Gunny Bag／Old Gunny Bag 新麻袋New Gunny Bag 尼龙袋Nylon Bag 聚丙烯袋Polypropylene Bag 聚乙烯袋Polythene Bag 塑料袋Poly Bag 塑料编织袋Polywoven Bag 纤维袋Fibre Bag 玻璃纤维袋Glass Fibre Bag 玻璃纸袋Callophane Bag 防潮纸袋Moisture Proof Pager Bag 乳胶袋子Emulsion Bag 三层牛皮纸袋3=ply Kraft Paper Bag 锡箔袋Fresco Bag 特大袋Jumbo Bag