mox1
MOX-1,2,3 & 4 MediceL?Performance Characteristics
Output
Range
Signal in 100% O
2
Resolution Expected Operating Life Response Time (air to
100% O
2
)
Linearity
Zero signal in N
2
at 20°C Operating Temp. Range Temp. Compensation
Pressure Range Relative Humidity Range Long Term Output Drift in
100% O
2
Housing Material
Packaging
N
2
O Resistance
Cross-Sensitivity
Warranty Period 9-13 mV in 210mBar O
2
0-1500mBar O
2
100±1%
1mBar O
2
1.5 x 106 % O
2
hours at 20°C 0.8 x 106 % O
2
hours at 40°C
T
90
< 15s
Linear 0-100% O
2
<200μV
-20°C to +50°C
±2% variation from 0-40°C
0.5-2.0Bar
0 to 99% non-condensing Typically <5% over 1 year
White ABS
Sealed blister packaging
Resistant to 100% N
2
O
Meets EN12598 requirements 13 months from date of despatch (This amounts to a variation of condition 6 of our standard terms and conditions which otherwise apply)
N.B.The specification is based on measurements made with cylinder gases using a flow rate of 100 mls min-1. Conditions at 20°C, 50%RH, and 1013mBar unless otherwise noted.
0088
Doc. Ref.: mox.pmd Issue 1.6Page 1 of 314th January 2004
MOX Outline Dimensions
N.B. All tolerances ±0.15mm unless otherwise stated
Doc. Ref.: mox.pmd Issue 1.6Page 2 of 314th January 2004
Doc. Ref.: mox.pmd Issue 1.6Page 3 of 314th January 2004
Every effort has been made to ensure the accuracy of this document at the time of printing. In accordance with the company’s policy of continued product improvement City Technology Limited reserves the right to make product changes without notice. No liability is accepted for any consequential losses, injury or damage resulting from the use of this document or from any omissions or errors herein. The data is given for guidance only. It does not constitute a specification or an offer for sale. The products are always subject to a programme of improvement and testing which may result in some changes in the characteristics quoted. As the products may be used by the client in circumstances beyond the knowledge and control of City Technology Limited, we cannot give any warranty as to the relevance of these particulars to an application. It is the clients’ responsibility to carry out the necessary tests to determine the usefulness of the products and to ensure their safety of operation in a particular application.
Performance characteristics on this data sheet outline the performance of newly supplied sensors. Output signal can drift below the lower limit over time.
Intended Use
These sensors are designed to be used to monitor the partial pressure of oxygen in anaesthesia, critical care,incubators and general Oxygen monitors.
Stabilisation time
Allow at least 15 minutes to stabilise in instrument before calibration.
Cleaning and Sterilisation
In case of contamination the sensor may be cleaned with distilled water and allowed to dry naturally. The sensor is not suitable for sterilisation by steam or exposure to chemicals such as ethylene oxide or hydrogen peroxide
Calibration Interval
These sensors are designed to have minimal drift over their useful lifetime however for maximun accuracy they should be calibrated in 100% Oxygen before use.
Cross-sensitivity
s a G t s e T O %(r o r r E 2)
O %05/e H %052%1 %5.1+o t 1+O %8.82/e n a h t o l a H %42N %2.76/2O %2o t %5.1+O %5.82/e n a r u l f o v e S %52N %5.66/2O %5.1+o t 1+O %5.82/e n a r u l f n E %52N %5.66/2O %8.1+o t 2.1+O %5.82/e n a r u l f o s I %52N %5.66/2O % 8.1o t 2.1+O C %52O %5.82/2N %5.66/2O % 1<