Futaba R6008HS_R6014HS 使用手册

Futaba R6008HS/R6014HS Manual https://www.wendangku.net/doc/5912724200.html,/file/2717941

From https://www.wendangku.net/doc/5912724200.html,

https://www.wendangku.net/doc/5912724200.html, collects and classifies the global product

instrunction manuals to help users access anytime and

anywhere, helping users make better use of products.

Home: https://www.wendangku.net/doc/5912724200.html,/ Chinese: https://www.wendangku.net/doc/5912724200.html,/

TM8(on 8ch mode), TM10(on 10ch mode), TM14(on multi-ch mode)

R6008HS/R6014HS

Compliance Information Statement (for U.S.A.)

This device, trade name Futaba Corporation of America, model number R6008HS/R6014HS, complies with part15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesiredoperation.The responsible party of this device compliance is:Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@https://www.wendangku.net/doc/5912724200.html, (Support)TEL (217)398-0007 or E-mail: service@https://www.wendangku.net/doc/5912724200.html, (Service)

R6008HS/R6014HS Specifi -cations

? Dual antenna diversity

? Power requirement: 4.8V or 6.0V battery or regulated output from ESC, etc. (*1)? Size: R6008HS: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)/R6014HS: 2.06 x 1.48 x 0.63 in. (52.3 x 37.5 x 16.0 mm)? Weight: R6008HS: 0.48 oz. (13.5g)/R6014HS: 0.72 oz. (20.8g)

(*1) Be sure that when using ESC's regulated

output the capacity of the ESC must meet your usage condition.

Re-adjust the F/S position (only

for TM-8)1 Press and hold the Link/Mode switch

between one(1) and two(2) seconds.

Makuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan

1M23N17413

?FUTABA CORPORA TION 2009, 01 (1)

Switch

Operation Mode Select

The operation mode is on "Normal mode" from factory shipping. When to change the mode, please follow the steps shown below.1 T urn off the receiver.

2 P ress and hold the link/mode switch and turn on the receiver. Keep the switch hold more than one(1) second. The LED starts flashing with the current status.

3 R elease the switch.

4 T urn off the receiver.

By doing this step, the mode can switch over between two(2) modes.

the LED when turning on the receiver. If possible there's no FASST transmitter turned on around you in order to make firmer check.

When turn on the receiver, the LED will be;

? Red when on "Normal mode"

? Green and Red (makes Orange) when on "High Speed mode". (After two(2) seconds, change to Red.)

If there are some FASST transmitter turned on around the receiver, the LED may show the above status for a brief moment then changed to the status indication as shown in the "LED indication" table.

LED Indication

Green Red Status

Solid Solid Initializing

Off Solid No signal reception Solid Off Receiving signals

Blink

Off

Receiving signals but ID is unmatched

Link to the transmitter

1 Press and hold the Link/Mode switch more

than two(2) seconds.

Thank you for purchasing the R6008HS , R6014HS FASST receiver. These models have two(2) operation mode as shown below.Normal mode/High Speed mode

The "Normal mode" accepts any type of servos or the peripherals as the frame rate of the output is 14ms. The "High Speed mode" only accept the digital servos for outputs from 1ch to 6ch, including BLS series, and most peripheral

equipments such as the gyros or brushless ESCs. The frame rate of the outputs is 7ms. The outputs for other channels indicated below allow to use any type of servos as the frame rate of these outputs are still 14ms on the High Speed mode.R6008HS - 7ch and 8ch

R6014HS - 7ch to 12ch, DG1, DG2

The R6008HS , R6014HS are compatible with the FASST transmitters as shown below.

MPDX-1 application(R6014HS only)

When to use the MPDX-1, please prepare the exclusive short-plug shown below.

Short-plug

(sold separately)

to R6014HS 's "DATA" port.

CH11 and Other channels can not use the MPDX-1.

? When not to use the MPDX-1, do not plug the short-plug to the "DAT A" port.

? Please note that when the short-plug is plugged to the "DA TA" port, both CH11 and CH12 become acceptable for MPDX-1. CH11 or CH12 can not separately set as the "MPDX-1-ready-output."