华三s2100配置

https://www.wendangku.net/doc/649643208.html,/Service/Document_Center/Switches/Catalog/S2100/S2108/Configure/User_Manual/H3C_S2100_UM(V1.04)/200906/636922_30005_0.htm#_Toc231880200
(s2100系列用户手册）
配置分级保护密码
system-view
Enter system view, return to user view with Ctrl+Z.
[H3C]super password H3C（h3c就是密码）
设置Web网管用户的用户名为admin，密码为123456，用户级别为管理级。
system-view
Enter system view, return to user view with Ctrl+Z.
[H3C]localuser admin 123456 1
进入AUX用户界面。
system-view
Enter system view, return to user view with Ctrl+Z.
[H3C]user-interface aux 0
[H3C-Aux]
配置AUX用户界面超时时间为8分30秒。
system-view
Enter system view, return to user view with Ctrl+Z.
H3C]user-interface aux 0
[H3C-Aux]idle-timeout 8 30
[H3C-Aux]
进入VTY用户界面。
system-view
Enter system view, return to user view with Ctrl+Z.
[H3C]user-interface vty 0
[H3C-vty]
配置VTY用户界面超时时间为7分钟。
system-view
Enter system view, return to user view with Ctrl+Z.
[H3C]user-interface vty 0
[H3C-vty]idle-timeout 7
在VTY视图下设置Telnet用户登录密码为H3C。
system-view
Enter system view, return to user view with Ctrl+Z.
[H3C]user-interface vty 0
[H3C-vty]set authentication password H3C（h3c就是密码）
创建管理VLAN 1接口。
system-view
Enter system view, return to user view with Ctrl+Z.
[H3C]vlan 1
[H3C-Vlan20]quit
[H3C]management-vlan 1
[H3C]interface vlan-interface 1
#为管理VLAN 1接口指定IP地址和掩码。
[H3C-Vlan-interface1]ip address 192.168.0.55 255.255.255.0
为管理VLAN接口指定/删除网关
[H3C-Vlan-interface1]ip ip gateway 192.168.0.1（配置完记得save保存，然后重启交换机reboot）
删除管理VLAN接口网关
[H3C-Vlan-interface1]undo ip gateway
设置端口隔离 24号口为进口
system-view
[Quidway]vlan 1
[Quidway-vlan1]port-isolate enable
[Quidway-vlan1]quit
[Quidway]interface Ethernet 0/24
[Quidway-Ethernet0/24]port-isolate uplink-port vlan 1
[Quidway-Ethernet0/24]quit
[Quidway]quit
save
设置端口流量为8M
system-view
[Quidway]interface Ethernet 0/1
[Quidway-Ethernet0/1]line-rate outbound 47
[Quidway-Ethernet0/1]line-rate inbound 47
[Quidway-Ethernet0/1]quit
[Quidway]interface Ethernet 0/2
[Quidway-Ethernet0/2]line-rate outbound 47
[Quidway-Ethernet0/2]line-rate inbound 47
从一口一直到23口
8M(35) 10M(37) 15M(42) 20M(47) 30M(57) 50M(77) 99M(126) 127(不限速）
**报文速率限制级别取值为1～127。如果速率限制级别取值在1～28范围内，则速率限制的粒度为64Kbps，这种情况下，当设置的级别为N，则端口上限制的速率大小为N*64K；如果速率限制级别取值在29～127范围内，则速率限制的粒度为1Mbps，这种情况下，当设置的级别为N，则端口上限制的速率大小为(N-27)*1Mbps
恢复

出厂值

restore default