模具工程常用词汇
模具钢材
alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板
carbon tool steel 碳素工具钢
clad sheet 被覆板
clod work die steel 冷锻模用钢
emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢
galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢
high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢
low alloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢
marging steel 马式体高强度热处理钢
martrix alloy 马特里斯合金
meehanite cast iron 米汉纳铸钢
meehanite metal 米汉纳铁
merchant iron 市售钢材
molybdenum high speed steel
钼系高速钢molybdenum steel
钼钢nickel chromium steel 镍铬钢
prehardened steel 顶硬钢
silicon steel sheet 硅钢板
stainless steel 不锈钢
tin plated steel sheet 镀锡铁板
tough pitch copper 韧铜
troostite 吐粒散铁
tungsten steel 钨钢
vinyl tapped steel sheet 塑料覆面钢板
四、模具零件:mold components
三板模:3-plate mold
二板模:2-plate mold
边钉/导边:leader pin/guide pin
边司/导套:bushing/guide bushing
中托司:shoulder guide bushing
中托边L:guide pin
顶针板:ejector retainner plate
托板:support plate
螺丝:screw
管钉:dowel pin
开模槽:ply bar scot
内模管位:core/cavity inter-lock
顶针:ejector pin
司筒:ejector sleeve
司筒针:ejector pin
推板:stripper plate
缩呵:movable core,return core core puller
扣机(尼龙拉勾):nylon latch lock
斜顶:lifter
模胚(架):mold base
上内模:cavity insert
下内模:core insert
行位(滑块):slide
镶件:insert
压座/斜鸡:wedge
耐磨板/油板:wedge wear plate
压条:plate
撑头: support pillar
唧嘴:sprue bushing 挡板:stop plate
定位圈:locating ring
锁扣:latch
扣鸡:parting lock set
推杆:push bar
栓打螺丝:S.H.S.B
顶板:eracuretun
活动臂:lever arm
分流锥:spure sperader
水口司:bush
垃圾钉:stop pin
隔片:buffle
弹弓柱:spring rod
弹弓:die spring
中托司:ejector guide bush
中托边:ejector guide pin
镶针:pin
销子:dowel pin
波子弹弓:ball catch
喉塞: pipe plug
锁模块:lock plate
斜顶:angle from pin
斜顶杆:angle ejector rod
尼龙拉勾:parting locks
活动臂:lever arm
复位键、提前回杆:early return bar
气阀:valves
斜导边:angle pin
术语:terms
承压平面平衡:parting surface support balance
模排气:parting line venting
回针碰料位:return pin and cavity interference
模总高超出啤机规格:mold base shut hight
顶针碰运水:water line interferes withejector pin
料位出上/下模:part from cavith (core) side
模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件:Do not use (core/cavity) insert
用铍铜做镶件:use beryllium copper insert
初步(正式)模图设计:preliinary (final) mold design
反呵:reverse core
弹弓压缩量:spring compressed length
稳定性好:good stability,stable
强度不够:insufficient rigidity
均匀冷却:even cooling
扣模:sticking
热膨胀:thero expansion
公差:tolorance
铜公(电极):copper electrode
模具工程常用词汇
die 模具die shoe 模座
figure file, chart file图档
cutting die, blanking die冲模
progressive die, follow (-on)die 连续模
compound die复合模
punched hole冲孔 panel board镶块
to cutedges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸
engraving, to engrave刻印
upsiding down edges翻边
to stake铆合
design modification设计变化 die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board范本
padding block垫块
stepping bar垫条
upper die base上模
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧 bolt螺栓
plate电镀
mold成型
material for engineering mold testing工程试模材料
not included in physical inventory不列入盘点
incoming material to be inspected进货待验
PCE assembly production schedule sheet PCE组装厂生产排配表
model机钟
work order工令
revision版次
production control confirmation生产确认
checked by初审
approved by核准
stock age analysis sheet 库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked 待验或重工
cause description原因说明
part number/ P/N 料号
item/group/class类别
prepared by制year-end physical inventory difference analysis sheet 年终盘点差异分析表
physical inventory盘点数量
physical count quantity账面数量
difference quantity差异
good product/accepted goods/ accepted parts/good parts 良品
defective product/non-good parts不良品
disposed goods处理品
on way location在途仓
oversea location海外仓spare parts physical inventory list 备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割 EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子
shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆
spring-box eject-plate弹簧箱顶板
bushing block衬套
insert 入块
capability能力
parameter参数 f
actor系数
phosphate皮膜化成
viscosity涂料粘度
alkalidipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模
demagnetization去磁;消磁
high-speed transmission高速传递
heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水
次 Chromate铬酸处理 Anodize阳性处理 seal封孔 revision 版次 part number/P/N料号 good products良
品 scraped products报放心品 defective products不良
品 finished products成品 disposed products处理
品 barcode条形码 flow chart流程窗体 assembly组
装 stamping冲压 molding成型 spare parts=buffer备
品 coordinate坐标 dismantle the die折模 auxiliary fuction 辅助功能 poly-line多义线 heater band 加热
片 thermocouple热电偶 sand blasting喷沙 grit 砂
砾 derusting machine除锈机 degate打浇口 dryer烘干
机 induction感应 induction light感应
光 response=reaction=interaction感应 ram连
杆 edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕疵 shine亮班 splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒 grit maker抽粒机cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨 drill
铝 boring镗 blinster气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank 摸柄 crank shaft曲柄 augular offset角度偏差 velocity速度 production tempo生产进度现状 torque扭
矩 spline=the multiple keys花键quenching淬火 tempering 回火
annealing退火 carbonization碳化 alloy合
金 tungsten high speed steel钨高速
的 moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性resistance 电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机模具工程类 plain die简易模 pierce die 冲孔模 forming die成型模 progressive die连续
模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce 冲孔 forming成型(抽凸,冲凸) draw hole抽
孔 bending折弯 trim切边 emboss凸点
dome凸圆 semi-shearing半剪 stamp mark冲记
号 deburr or coin压毛边 punch riveting冲压铆
合 side stretch侧冲压平 reel stretch卷圆压平 groove压
线 blanking下料 stamp letter冲字(料号) shearing剪
断 tick-mark nearside正面压印 tick-mark farside反面压印冲压名称类 extension dwg展开图 procedure dwg工程
图 die structure dwg模具结构图 material材
质 material thickness料片厚度
press specification冲床规格 die height range适用模
高 die height闭模高度 burr毛边 gap间隙 punch wt.上模重量
五金零件类
inner guiding post内导柱 inner hexagon screw内六角螺钉 dowel pin固定销coil spring弹簧 lifter pin顶料
销 eq-height
sleeves=spool等高套筒 pin销 lifter guide pin浮升导料
销 guide pin导正销wire spring圆线弹簧 outer guiding post 外导柱 stop screw止付螺丝 located pin定位销 outer bush 外导套
范本类
top plate上托板(顶板) top block上垫脚 punch set上模
座 punch pad上垫板 punch holder上夹板
stripper pad脱料背板
up stripper上脱料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板lower plate下模板 die pad下垫板 die holder下夹板 die set下模
座 bottom block下垫脚 bottom plate下托板(底
板) stripping plate内外打(脱料板)
outer stripper外脱料板 inner stripper内脱料
板 lower stripper下脱料板
零件类 punch冲头 insert入块(嵌入件) deburring punch压毛边冲子 groove punch压线冲子 stamped punch字模冲子 round punch圆冲子 special shape punch异形冲
子 bending block折刀 roller滚轴 baffle plate挡
块 located block定位块 supporting block for location 定位支承块 air cushion plate气垫板 air-cushion eject-rod气垫顶杆 trimming punch切边冲子 stiffening rib punch
一、 = stinger 加强筋冲子 ribbon punch压筋冲
子 reel-stretch punch卷圆压平冲子 guide plate定位
板 sliding block滑块 sliding dowel block滑块固定
块 active plate活动板 lower sliding plate下滑块
板 upper holder block上压块 upper mid plate上中间
板 spring box弹簧箱 spring-box eject-rod弹簧箱顶
杆 spring-box eject-plate弹簧箱顶板 bushing bolck衬
套 cover plate盖板
guide pad导料块
塑件&模具相关英文
compre sion molding压缩成型 flash mold溢流式模
具 plsitive mold挤压式模具split mold分割式模具 cavity型控母模 core模心公模 taper锥拔 leather cloak仿皮
革 shiver饰纹 flow mark流痕 welding mark溶合
痕 post screw insert螺纹套筒埋值
self tapping screw自攻螺丝 striper plate脱料板piston活塞 cylinder汽缸套 chip细碎物 handle mold掌上型模具(移转成型用模具) encapsulation molding低压封装成
型(射出成型用模具)
two plate两极式(模具) well type蓄料井 insulated runner 绝缘浇道方式 hot runner热浇道 runner plat浇道模
块 valve gate阀门浇口 band heater环带状的电热
器 spindle阀针 spear head刨尖头 slag well冷料
井 cold slag冷料渣 air vent排气道 welding line熔合
痕 eject pin顶出针 knock pin顶出销 return pin回位销反顶针 sleave套筒 stripper plate脱料板 insert core放置入子runner stripper plate浇道脱料板 guide pin导
销 eject rod (bar)(成型机)顶业捧 subzero深冷处理three plate三极式模具
runner system浇道系统 stress crack应力电裂 orientation 定向 sprue gate射料浇口,直浇口 nozzle射
嘴 sprue lock pin料头钩销(拉料杆) slag well冷料
井 side gate侧浇口 edge gate侧缘浇口 tab gate搭接浇
口 film gate薄膜浇口 flash gate闸门浇口
slit gate缝隙浇口 fan gate扇形浇口 dish gate因盘形浇
口 diaphragm gate隔膜浇口 ring gate环形浇
口 subarine gate潜入式浇口
tunnel gate隧道式浇口 pin gate针点浇口 Runner less无浇道 (sprue less)无射料管方式 long nozzle延长喷嘴方
式 sprue浇口;溶渣
各种模具常用成形方式 accurate die casting 精密压
铸 powder forming 粉末成形 calendaring molding 压延成形 powder metal forging 粉末锻造
cold chamber die casting 冷式压铸
precision forging 精密锻造
cold forging 冷锻
press forging 冲锻
compacting molding 粉末压出成形
rocking die forging 摇动锻造
compound molding 复合成形
rotary forging 回转锻造
compression molding 压缩成形
rotational molding 离心成形
dip mold 浸渍成形
rubber molding 橡胶成形
encapsulation molding 注入成形
sand mold casting 砂模铸造
extrusion molding 挤出成形
shell casting 壳模铸造
foam forming 泡沫成形
sinter forging 烧结锻造
forging roll 轧锻
six sides forging 六面锻造
gravity casting 重力铸造
slush molding 凝塑成形
hollow(blow) molding 中空(吹出)成形
squeeze casting 高压铸造
hot chamber die casting 热室压铸
swaging 挤锻
hot forging 热锻
transfer molding 转送成形
injection molding 射出成形
warm forging 温锻
investment casting 精密铸造
matched die method 对模成形法 laminating method 被覆淋膜成形
low pressure casting 低压铸造
lost wax casting 脱蜡铸造
matched mould thermal forming 对模热成形模
各式模具分类用语
bismuth mold 铋铸模
landed plunger mold 有肩柱塞式模具
burnishing die 挤光模
landed positive mold 有肩全压式模具
button die 镶入式圆形凹模
loading shoe mold 料套式模具
center-gated mold 中心浇口式模具
loose detail mold 活零件模具
chill mold 冷硬用铸模
loose mold 活动式模具
clod hobbing 冷挤压制模
louvering die 百叶窗冲切模
composite dies 复合模具
manifold die 分歧管模具
counter punch 反凸模
modular mold 组合式模具
double stack mold 双层模具
multi-cavity mold 多模穴模具
electroformed mold 电铸成形模multi-gate mold 复式浇口模具
expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模
palletizing die 迭层模
family mold 反套制品模具
plaster mold 石膏模
transfer die连续自动冲切,连续冲模blank through dies 漏件式落料模
porous mold 通气性模具
duplicated cavity plate 复板模
positive mold 全压式模具
fantail die 扇尾形模具
pressure die 压紧模
fishtail die 鱼尾形模具
profile die 轮廓模
flash mold 溢料式模具
progressive die 顺序模
gypsum mold 石膏铸模
protable mold 手提式模具
hot-runner mold 热流道模具
prototype mold 雏形试验模具
ingot mold 钢锭模
punching die 落料模
lancing die 切口模
raising(embossing) 压花起伏成形
re-entrant mold 倒角式模具
sectional die 拼合模
runless injection mold 无流道冷料模具
sectional die 对合模具
segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套
single cavity mold 单腔模具
solid forging die 整体锻模
split forging die 拼合锻模
split mold 双并式模具
sprueless mold 无注道残料模具
squeezing die 挤压模
stretch form die 拉伸成形模
sweeping mold 平刮铸模
swing die 振动模具
three plates mold 三片式模具
trimming die 切边模
unit mold 单元式模具
universal mold 通用模具unscrewing mold 退扣式模具
yoke type die 轭型模
模具厂常用之标准零配件
air vent vale 通气阀
anchor pin 锚梢
angular pin 角梢
baffle 调节阻板
angular pin 倾斜梢
baffle plate 折流檔板
ball button 球塞套
ball plunger 定位球塞
ball slider 球塞滑块binder plate 压板blank holder 防皱压板
blanking die 落料冲头
bolster 上下范本
bottom board 浇注底板
bolster 垫板
bottom plate 下固定板
bracket 托架
bumper block 缓冲块
buster 堵口
casting ladle 浇注包
casting lug
铸耳 cavity 模穴(模仁)
cavity retainer plate 模穴托板center pin 中心梢
clamping block 锁定块
coil spring 螺旋弹簧
cold punched nut 冷冲螺母
cooling spiral 螺旋冷却栓
core 心型
core pin 心型梢
cotter 开口梢
cross 十字接头
cushion pin 缓冲梢
diaphragm gate 盘形浇口
die approach 模头料道
die bed 型底 die block 块形模体
die body 铸模座die bush 合模衬套
die button 冲模母模
die clamper 夹模器
die fastener 模具固定用零件
die holder 母模固定板
die lip 模唇
die plate 冲范本
die set 冲压模座
direct gate 直接浇口
dog chuck 爪牙夹头
dowel 定位梢
dowel hole 导套孔
dowel pin 合模梢
dozzle 辅助浇口
dowel pin 定位梢
draft 拔模锥度
draw bead 张力调整杆
drive bearing 传动轴承
ejection pad 顶出衬垫
ejector 脱模器
ejector guide pin 顶出导梢
ejector leader busher 顶出导梢衬套ejector pad 顶出垫
ejector pin 顶出梢
ejector plate 顶出板
ejector rod 顶出杆 ejector sleeve 顶出衬套ejector valve 顶出阀
eye bolt 环首螺栓
filling core 椿入蕊
film gate 薄膜形浇口
finger pin 指形梢
finish machined plate 角形范本
finish machined round plate 圆形范本fixed bolster plate 固定侧模板
flanged pin 带凸缘销
flash gate 毛边形浇口
flask 上箱
floating punch 浮动冲头
gate 浇口
gate land 浇口面
gib 凹形拉紧楔
goose neck 鹅颈管
guide bushing 引导衬套
guide pin 导梢
guide post 引导柱
guide plate 导板
guide rail 导轨
head punch 顶头冲孔
headless punch 直柄冲头
heavily tapered solid 整体模蕊盒hose nippler 管接头
impact damper 缓冲器
injection ram 压射柱塞
inlay busher 嵌入衬套
inner plunger 内柱塞
inner punch 内冲头
insert 嵌件
insert pin 嵌件梢
king pin 转向梢
king pin bush 主梢衬套
knockout bar 脱模杵
land 合模平坦面
land area 合模面
leader busher 导梢衬套
lifting pin 起模顶销
lining 内衬
locating center punch 定位中心冲头locating pilot pin 定位导梢
locating ring 定位环
lock block 压块
locking block 定位块
locking plate 定位板
loose bush 活动衬套
making die 打印冲子
manifold block 歧管档块
master plate 靠模样板
match plate 分型板
mold base 塑料模座
mold clamp 铸模紧固夹
mold platen 模用板
moving bolster 换模保持装置moving bolster plate 可动侧范本one piece casting 整体铸件parallel block 平行垫块paring line 分模线
parting lock set 合模定位器
pass guide 穴型导板
peened head punch 镶入式冲头pilot pin 导销
pin gate 针尖浇口
plate 衬板
pre extrusion punch 顶挤冲头punch 冲头
puncher 推杆
pusher pin 衬套梢
rack 机架
rapping rod 起模杆
re-entrant mold 凹入模
retainer pin 嵌件梢
retainer plate 托料板
return pin 回位梢
riding stripper 浮动脱模器
ring gate 环型浇口
roller 滚筒
runner 流道
runner ejector set 流道顶出器runner lock pin 流道拉梢
screw plug 头塞 set screw 固定螺丝shedder 脱模装置
shim 分隔片
shoe 模座之上下范本
shoot 流道
shoulder bolt 肩部螺丝
skeleton 骨架
slag riser 冒渣口
slide(slide core) 滑块
slip joint 滑配接头
spacer block 间隔块
spacer ring 间隔环 spider 模蕊支架spindle 主轴
sprue 注道
sprue bushing 注道衬套
sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料
spue line 合模线
square key 方键
square nut 方螺帽
square thread 方螺纹
stop collar 限位套
stop pin 止动梢
stop ring 止动环
stopper 定位停止梢
straight pin 圆柱销
stripper bolt 脱料螺栓
stripper bushing 脱模衬套
stripper plate 剥料板
stroke end block 行程止梢
submarine gate 潜入式浇口
support pillar 支撑支柱/顶出支柱support pin 支撑梢
supporting plate 托板
sweep templete 造模刮板
tab gate 辅助浇口
taper key 推拔键
taper pin 拔锥梢/锥形梢
teeming 浇注
three start screw 三条螺纹
thrust pin 推力销
tie bar 拉杵
tunnel gate 隧道形浇口
vent 通气孔
wortle plate 拉丝范本
模具常用之工作机械
3D coordinate measurement 三次元量床boring machine 搪孔机
cnc milling machine CNC铣床contouring machine 轮廓锯床
copy grinding machine 仿形磨床
copy lathe 仿形车床
copy milling machine 仿形铣床
copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机
drilling machine 冲孔机
engraving machine 雕刻机
engraving E.D.M. 雕模放置加工机
form grinding machine 成形磨床graphite machine 石墨加工机
horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床
jig boring machine 冶具搪孔机
jig grinding machine 冶具磨床
lap machine 研磨机
machine center 加工制造中心
multi model miller 靠磨铣床
NC drilling machine NC钻床
NC grinding machine NC磨床 NC lathe NC车床NC programming system NC程序制作系统planer 龙门刨床
profile grinding machine 投影磨床
projection grinder 投影磨床
radial drilling machine 旋臂钻床
shaper 牛头刨床
surface grinder 平面磨床
try machine 试模机
turret lathe 转塔车床
universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心
wire E.D.M. 线割放电加工机
具钢材
alloy tool steel 合金工具钢
aluminium alloy 铝合金钢
bearing alloy 轴承合金
blister steel 浸碳钢
bonderized steel sheet 邦德防蚀钢板
carbon tool steel 碳素工具钢
clad sheet 被覆板
clod work die steel 冷锻模用钢
emery 金钢砂
ferrostatic pressure 钢铁水静压力
forging die steel 锻造模用钢
galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢
high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢
low alloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢
martrix alloy 马特里斯合金
meehanite cast iron 米汉纳铸钢
meehanite metal 米汉纳铁
merchant iron 市售钢材
molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢 nickel chromium steel 镍铬钢prehardened steel 顶硬钢
silicon steel sheet 硅钢板
stainless steel 不锈钢
tin plated steel sheet 镀锡铁板
tough pitch copper 韧铜
troostite 吐粒散铁
tungsten steel 钨钢
vinyl tapped steel sheet 塑料覆面钢板
tap 攻牙
表面处理关连用语
age hardening 时效硬化
ageing 老化处理
air hardening 气体硬化
air patenting 空气韧化
annealing 退火
anode effect 阳极效应
anodizing 阳极氧化处理
atomloy treatment 阿托木洛伊表面
austempering 奥氏体等温淬火
austenite 奥斯田体/奥氏体
bainite 贝氏体
banded structure 条纹状组织
barrel plating 滚镀
barrel tumbling 滚筒打光
blackening 染黑法
blue shortness 青熟脆性
bonderizing 磷酸盐皮膜处理
box annealing 箱型退火
box carburizing 封箱渗碳
bright electroplating 辉面电镀
bright heat treatment 光辉热处理
bypass heat treatment 旁路热处理
carbide 炭化物
carburized case depth 浸碳硬化深层
carburizing 渗碳
cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化
coating 涂布被覆
cold shortness 低温脆性comemtite 渗碳体
controlled atmosphere 大气热处理corner effect 锐角效应
creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火
depth of hardening 硬化深层diffusion 扩散
diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花
etching 表面蚀刻
ferrite 肥粒铁
first stage annealing 第一段退火flame hardening 火焰硬化
flame treatment 火焰处理
full annealing 完全退火
gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度
granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性
hardenability curve 硬化性曲线hardening 硬化
heat treatment 热处理
hot bath quenching 热浴淬火
hot dipping 热浸镀
induction hardening 高周波硬化
ion carbonitriding 离子渗碳氮化
ion carburizing 离子渗碳处理
ion plating 离子电镀
isothermal annealing 等温退火liquid honing 液体喷砂法
low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理
martensite 马氏体/硬化铁炭metallikon 金属喷镀法
metallizing 真空涂膜
nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化
oil quenching 油淬化
overageing 过老化
overheating 过热
pearlite 针尖组织
phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化
pre-annealing 预备退火precipitation 析出
precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化
quench hardening 淬火
quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶
red shortness 红热脆性
residual stress 残留应力
retained austenite 残留奥
rust prevention 防蚀
salt bath quenching 盐浴淬火
sand blast 喷砂处理
seasoning 时效处理
second stage annealing 第二段退火secular distortion 经年变形segregation 偏析
selective hardening 部分淬火
shot blast 喷丸处理
shot peening 珠击法
single stage nitriding 等温渗氮sintering 烧结处理
soaking 均热处理
softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火
stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化
stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷
surface hardening 表面硬化处理temper brittleness 回火脆性
temper colour 回火颜色
tempering 回火
tempering crack 回火裂痕
texture 咬花
thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态
tufftride process 软氮化处理
under annealing 不完全退火
vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火
vacuum heat treatment 真空热处理vacuum nitriding 真空氮化
water quenching 水淬火
wetout 浸润处理
射出成形关联用语
activator 活化剂
bag moulding 气胎施压成形
bonding strength 黏合强度
breathing 排气
caulking compound 填隙料
cell 气孔
cold slug 半凝式射出
colorant 着色剂
color matching 调色
color masterbatch 色母料
compound 混合料
copolymer 共聚合体
cull 残料废品
cure 凝固化
cryptometer 不透明度仪
daylight 开隙
dry cycle time 空料试车周期时间ductility 延性
elastomer 弹性体
extruded bead sealing 压出粒涂层法feed 供料
filler 充填剂
film blowing 薄膜吹制法
floating platen 活动范本
foaming agent 发泡剂
gloss 光泽
granule 颗粒料
gunk 料斗
hot mark 热斑
hot stamping 烫印
injection nozzle 射出喷嘴
injection plunger 射出柱塞
injection ram 射出冲柱
isomer 同分异构物
kneader 混合机
leveling agent 匀涂剂
lubricant 润滑剂
matched die method 配合成形法mould clamping force 锁模力
mould release agent 脱模剂
nozzle 喷嘴
oriented film 取向薄膜
parison 吹气成形坏料
pellet 粒料
plasticizer 可塑剂
plunger 压料柱塞
porosity 孔隙率
post cure 后固化
premix 预混料
purging 清除
reciprocating screw 往复螺杆resilience 回弹性
resin injection 树脂射出法
rheology 流变学
sheet 塑料片shot 注射
shot cycle 射出循环
slip agent 光滑剂
take out device 取料装置
tie bar 拉杆
toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板
transparency 透明性
void content 空洞率塑料原料
acrylic 压克力
casein 酪素
cellulose acetate 醋酸纤维素CA
cellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料
cresol resin 甲酚树脂CF
dially phthalate 苯二甲酸二烯丙酯
disperse reinforcement 分散性强化复合材料engineering plastics 工程塑料
epoxy resin 环氧树脂EP
ethyl cellulose 乙基纤维素
ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVA ethylene-vinlacetate copolyme 醋酸乙烯共聚物EVA fiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPE
high impact polystyrene 高冲击聚苯乙烯HIPS
high impact polystyrene rigidity 高冲击性聚苯乙烯
low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素
phenolic resin 酚醛树脂
plastic 塑料
polyacrylic acid 聚丙烯酸PAP
polyamide 耐龙PA
polybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PC
polyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POM
polyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO
polypropylene 聚丙烯PP
polystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE
polyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVA polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物
silicone resin 硅树脂
thermoplastic 热塑性
thermosetting 热固性
thermosetting plastic 塑料
unsaturated polyester 不饱和聚酯树脂
成形不良用语
aberration 色差
bite 咬入
blacking hole 涂料孔(铸疵)
blacking scab 涂料疤
blister 起泡
blooming 起霜
blow hole 破孔
blushing 泛白
body wrinkle 侧壁皱纹
breaking-in 冒口带肉
bubble 膜泡
burn mark 糊斑
burr 毛边
camber 翘曲
cell 气泡
center buckle 表面中部波皱
check 细裂痕
checking 龟裂
chipping 修整表面缺陷
clamp-off 铸件凹痕
collapse 塌陷
color mottle 色斑corrosion 腐蚀
crack 裂痕
crazing 碎裂
crazing 龟裂
deformation 变形
edge 切边碎片
edge crack 裂边
fading 退色
filler speak 填充料斑fissure 裂纹
flange wrinkle 凸缘起皱flaw 刮伤
flow mark 流痕
galling 毛边
glazing 光滑
gloss 光泽
grease pits 污斑
grinding defect 磨痕haircrack 发裂
haze 雾度
incrustation 水锈indentation 压痕
internal porosity 内部气孔mismatch 偏模
mottle 斑点
necking 缩颈
nick 割痕
range peel 橘皮状表面缺陷overflow 溢流
peeling 剥离
pit 坑
pitting corrosion 点状腐蚀plate mark 范本印痕
pock 麻点
pock mark 痘斑
resin streak 树脂流纹resin wear 树脂脱落
riding 凹陷
sagging 松垂saponification 皂化
scar 疤痕
scrap 废料
scrap jam 废料阻塞
scratch 刮伤/划痕
scuffing 深冲表面划伤
seam 裂痕
shock line 模口挤痕
short shot 充填不足
shrinkage pool 凹孔
sink mark 凹痕
skin inclusion 表皮折迭straightening 矫直
streak 条状痕
surface check 表面裂痕
surface roughening
橘皮状表皮皱折
surging 波动
torsion 扭曲
warpage 翘曲
waviness 波痕
webbing 熔塌
weld mark 焊痕
whitening 白化
wrinkle 皱纹
模具常用刀具工作法用语adjustable spanner 活动扳手angle cutter 角铣刀
arbour 心轴
backing 衬垫
belt sander 带式打磨机
buffing 抛光
chamfering machine 倒角机chamfering tool 去角刀具
chisel 扁錾
chuck 夹具
compass 两角规
concave cutter 凹面铣刀
convex cutter 凸形铣刀
cross joint 十字接头
cutting edge clearance 刃口余隙角drill stand 钻台
edge file 刃用锉刀
file 锉刀flange joint 凸缘接头
grinder 砂轮机
hammer 铁锤
hand brace 手摇钻
hatching 剖面线
hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽
index head 分度头
jack 千斤顶
jig 治具
kit 工具箱
lapping 研磨
metal saw 金工锯
nose angle 刀角
pinchers 钳子
pliers 铗钳 plug 柱塞头
polisher 磨光器
protable driller 手提钻孔机punch 冲头
sand paper 砂纸
scraper 刮刀
screw driver 螺丝起子
scribing 划线
second out file 中纹锉
spanner 扳手
spline broach 方栓槽拉刀square 直角尺
square sleeker 方形镘刀
square trowel 直角度
stripping 剥离工具
T-slot T形槽
tool for lathe 车刀
tool point angle 刀刃角
tool post 刀架
tosecan 划线盘
trimming 去毛边
waffle die flattening 压纹效平wiper 脱模钳
wrench 螺旋扳手
各种冲模加工关连用语
barreling 滚光加工
belling 压凸加工
bending 弯曲加工
blanking 下料加工
bulging 撑压加工
burring 冲缘加工
cam die bending 凸轮弯曲加工coining 压印加工
compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工
curl bending 卷边弯曲加工
curling 卷曲加工
cutting 切削加工
dinking 切断蕊骨
double shearing 迭板裁断drawing 引伸加工
drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工
filing 锉削加工
fine blanking 精密下料加工
finish blanking 光制下料加工finishing 精整加工
flanging 凸缘加工
folding 折边弯曲加工
folding 折迭加工
forming 成形加工
impact extrusion 冲击挤压加工indenting 压痕加工
ironing 引缩加工
knurling 滚花
lock seaming 固定接合
louvering 百叶窗板加工
marking 刻印加工
necking 颈缩加工
notching 冲口加工
parting 分断加工
piercing 冲孔加工
progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工
restriking 二次精冲加工
riveting 铆接加工
roll bending 滚筒弯曲加工
roll finishing 滚压加工
rolling 压延加工
roughing 粗加工
scrapless machining 无废料加工seaming 折弯重迭加工
shaving 缺口修整加工
shearing 切断加工
sizing 精压加工/矫正加工
slitting 割缝加工
spinning 卷边?接
stamping 锻压加工
swaging 挤锻压加工
trimming 整缘加工
upsetting 锻粗加工
wiring 抽线加工
冲压机械及周边关连用语
back shaft 支撑轴
blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤
brake 煞车 buckle 剥砂面camlachie cramp 铸包
chamotte sand 烧磨砂
charging hopper 加料漏斗clearance 间隙
closed-die forging 合模锻造clump 夹紧
clutch 离合器
clutch brake 离合器制动器
clutch boss 离合器轮壳
clutch lining 离合器覆盖
coil car 带卷升降运输机
coil cradle 卷材进料装置
coil reel stand 钢材卷料架
column 圆柱
connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架
crank 曲柄轴
crankless 无曲柄式
cross crank 横向曲轴
cushion 缓冲
depression 外缩凹孔
dial feed 分度送料
die approach 模口角度
die assembly 合模
die cushion 模具缓冲垫
die height 冲压闭合高度
die life 模具寿命
die opening 母模逃孔
die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角
edging 边锻伸
embedded core 加装砂心
feed length 送料长度
feed level 送料高度
filling core 埋入砂心
filling in 填砂
film play 液面花纹
fine blanking press 精密下料冲床forging roll 辊锻机
finishing slag 炼后熔渣
fly wheel 飞轮
fly wheel brake 飞轮制动器
foot press 脚踏冲床
formboard 进模口板
frame 床身机架
friction 摩擦
friction brake 摩擦煞车
gap shear 凹口剪床
gear 齿轮
gib 滑块引导部
gripper 夹具
gripper feed 夹持进料
gripper feeder 夹紧传送装置hammer 槌机
hand press 手动冲床
hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床
hopper feed 料斗送料
idle stage Idle Station 空站
inching 微调尺寸
isothermal forging 恒温锻造
key clutch 键槽离合器
knockout 脱模装置
knuckle mechanic 转向机构
land 模具直线刀面部
loader 供料器 unloader 卸料机
loop controller 闭回路控制器
lower die 下模
micro inching device 微寸动装置microinching equipment 微动装置
moving bolster 活动工作台
notching press 冲缺口压力机
opening 排料逃孔
overload protection device 防超载装置pinch roll 导正滚轮
pinion 小齿轮
pitch 节距
pressfit 压入
progressive 连续送料
pusher feed 推杆式送料
pusher feeder 料片押片装置
quick die change system 快速换模系统regrinding 再次研磨
releasing 松释动作
reversed blanking 反转下料
robot 机器人
roll forming machine 辊轧成形
roll forming machine 辊轧成形机
roll release 脱辊
roller feed 辊式送料
roller leveler 辊式矫直机
rotary bender 卷弯成形机
safety guard 安全保护装置
scrap cutter 废料切刀
scrap press 废料冲床
seamless forging 无缝锻造shave 崩砂
shear angle 剪角
sheet loader 薄板装料机
shot 单行程工作
shrinkage fit 收缩配合
shut height 闭合高度
sieve mesh 筛孔
sintering of sand 铸砂烧贴
slide balancer 滑动平衡器
slug hole 逃料孔
spin forming machine 旋压成形机spotting 合模
stack feeder 堆栈拨送料机stickness 黏模性
straight side frame 冲床侧板stretcher leveler 拉伸矫直机
strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程
take out device 取料装置
toggle press 肘杆式压力机transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机
unloader 卸载机
vibration feeder 振动送料机wiring press 嵌线卷边机
线切割放电加工关连用语abnormal glow 不规则辉光放电arc discharge 电弧放电
belt 皮带
centreless 无心
chrome bronze 铭铜
clearance angle 后角
corner shear drop 直角压陷deflection 桡曲度
discharge energy 放电能量dressing 修整
dwell 保压flange 凸缘
gap 间隙
graphite 石墨
graphite contraction allowance 电极缩小余量graphite holder 电极夹座
hair crack 发裂
horn 电极臂
jump 跳刀
magnetic base 磁性座
master graphite 标准电极
pipe graphite 管状电极
pulse 脉冲
rib working 肋部加工
roller electrode 滚轮式电极
rotary surface 旋转面
shank 柄部
sharp edge 锐角部
tough bronze 韧铜
traverse 摇臂
tungsten bronze 钨青铜
waviness 波形起伏
working allowance 加工余量
working dischard 加工废料
锻铸造关连用语
accretion 炉瘤
acid converter 酸性转炉
acid lining cupola 酸性熔铁炉
acid open-hearth furnace 酸性平炉
aerator 松砂机
air set mold 常温自硬铸模
airless blasting cleaning 离心喷光
all core molding 集合式铸模
all round die holder 通用模座
assembly mark 铸造合模记号
back pouring 补浇注
backing sand 背砂
base bullion 粗金属锭
base permeability 原砂透气度
belling 压凸
billet 坏料
bleed 漏铸
blocker 预锻模膛
blocking 粗胚锻件
blow hole 铸件气孔
board drop hammer 板落锤bottom pour mold 底浇
bottom pouring 底注
boxless mold 脱箱砂模
break-off core 缩颈砂心
brick molding 砌箱造模法buckle 剥砂面
camber 错箱
camlachie cramp 铸包
cast blade 铸造叶片
casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心范本
core vent 砂蕊排气孔
corner gate 压边浇口
counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔
die approach 模口角度
draw out 锻造拔长
draw plate 起范本
draw spike 起模长针dummying 预锻
embedded core 加装砂心erosion 冲砂
fettling 铸件清理
filling core 埋入砂心
filling in 填砂
film play 液面花纹
finishing slag 炼后熔渣
flash gutter 锻模飞边槽
flask molding 砂箱造模
forging roll 辊锻机
formboard 进模口板gutter 锻模飞边槽
hammer man 锻工
heading machine 顶镦机impacter 卧式锻造机
inblock cast 整体铸造
ingot 铸锭
ingot blank 铸坯
inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸
roll forging 轧锻
rolled surface 轧制表面rough sand 粗砂
roughing forge 粗锻
sand crushing 塌箱seamless forging 无缝锻造separate 分离
shave 崩砂
shrinkage fit 收缩配合
shut height 闭合高度
sieve mesh 筛孔
sintering of sand 铸砂烧贴slag 熔渣
slag inclusion 夹渣stickness 黏模性
strip layout 带状胚料排样法tap casting 顶注
top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置
upending 顶锻
uphill casting 底铸
white cast iron 白口铸件
模具加工方法
barrel 滚筒(加工)
bending 波纹加工broaching 拉刀切削
centering 定中心
cutting 切削
cylindrical lathe cutting 外圆车削electric discharge machine 放电加工electrolytic grinding 电解研磨embossing 压花加工
facing 面车削
filing 锉刀修润
hand finishing 手工修润
hemming 卷边加工
hobbing 滚齿加工
joggling 摇动加工
lapping 抛光/研磨修润
laser beam machining 雷射加工lathe cutting 车床车削
planning 刨削加工
polishing 抛亮光
reaming 铰孔修润
rough machining 粗切削
rounding 圆形加工
sawing 锯削
scaling 清除钢碇缺陷
shaping 成形加工
skiving 表面研磨 slotting 切缝切削taper turning 锥度车削
thread cutting 螺纹切削
ultrasonic machining 超音波加工
up cut milling 逆铣加工
砂轮用语
abrasive 砂轮
Al2O3 氧化铝
borazon 氧化硼立方晶
buffing wheel 抛光布轮
diamond 钻石
dresser 砂轮整修机
dressing 修整
endless grinding belt 循环式研磨带finishing allowance 加工余量
grain 磨粒
grinding disc 研磨盘
jamp up 孔眼堵塞mesh 网筛目
resinoid grinding wheel 半树脂型砂轮 slitting 切缝量vitrified 陶瓷的
机械设计及周边其它用语
assembly drawing 装配图
auto tool change cycle 自动换刀时间周期
beam 横梁
bending moment 弯矩
bending stress 弯曲应力
bottoming 底靠
buckling 纵弯曲
chamfering 去角斜切
channel 凹槽
chattering 颤动
check point 查核点
chip 切屑
chip conveyor 排屑输送机
coefficient of friction 摩擦系数
compact 小型的
cooling pipe 冷却管
coupon 试样胚
deflection 挠曲量
distortion 扭曲变形
draft taper 拔模锥度
draw out 拉拔
fit tolerance 配合公差
flexible rigidity 弯曲刚性
gas vent 气孔
hatching 剖面线
heater cooler 加热器冷却装置
hook cavity 钩穴
inching 寸动
lug 凸缘
maintenance 维修保固
metallurgy 冶金学
notch effect 切口效果
out of roughness 真圆度
performance 动作性能
pit 坑
plane strain 倒角应力
plug mill 蕊棒轧管机
repeated load 重复载荷
riveted joint 铆钉接合
sand paper 砂纸
shift 偏移
shrink fit 热压配合
shrinkage hole 缩孔
sinking 凹陷
sketch 草图
spalling 剥落
straightness 直度
submarine 深陷式
surface roughness 表面粗度
tapping 攻螺丝
thermocouple 热电耦
torsion load 扭转载荷
toughness 韧性
tracing 描图
under cut 凹割
3D coordinate measurement 三次元量床3D modeling 三次元模拟
aberration 色差
abnormal glow 不规则辉光放电abrasive 砂轮 access 通路
accretion 炉瘤
accurate die casting 精密压铸
acid converter 酸性转炉
acid lining cupola 酸性熔铁炉
acid open-hearth furnance 酸性平炉activator 活化剂
acetylene 乙炔
adjustable spanner 活动扳手
aerator 松砂机
age hardening 时效硬化
ageing 老化处理
air hardening 气体硬化
airless plasting cleaning 离心喷光
air patenting 空气韧化
air permeability test 透气性试验
air set mold 常温自硬铸模
air vent valve 通气阀
all core molding 集合式铸模
alloy tool steel 合金工具钢allround die holder 通用模型aluminium alloy 铝合金钢ampere 电流安培梢
angle cutter 角铣刀
angle welding 角焊
angular pin 角梢
angular pin 倾斜梢
anode effect 阳极效应annealing 退火
anchor pin 锚
abrasive grinding 强力磨削abrasive 磨料的,研磨的absence 不在,缺席accesssory 附件accommodate 适应
accordingly 因此,从而,相应地accuracy 精度,准确性
actuate 开动(机器),驱动adequate 足够的
adhesive 粘合剂
adjacent 邻近的
adopt 采用
advance 进步
advisable 可取的
agitate 摇动
a large extent 很大程度algorithm 算法
align 定位,调准
alignment 校直
all-too-frequent 频繁allowance 容差,余量
alternate 交替,轮流alternatively 做为选择,也许aluminiun 铝
ample 充足的
analysis 分析
ancillary 补助的,副的angular 有角的
annealing 退火
aperture 孔
applied loads 作用力appropriate 适当的
arc 弧,弓形
arise 出现,发生
arrange 安排
article 制品,产品
ascertain 确定,查明
assemble 组装attitude 态度auxiliary 辅助的
avoid 避免axis 轴axle 轮轴,车轴alternative 替换物backup 备份batch 一批bearing 轴承,支座
bed 床身behavior 性能
bench-work 钳工工作bend 弯曲beneath 在??下
bin 仓,料架blank 坯料blank 冲裁,落料
blanking 落料模blast 一阵(风)blemish 缺点,污点bolster 模座,垫板boring 镗削,镗孔bracket 支架brass 黄铜break down 破坏breakage 破坏brine 盐水brittle 易碎的
buffer 缓冲器built-in 内装的bulging 凸肚
burr 毛刺bush 衬套by far ?得多,最
by means of 借助于boost 推进cabinet 橱柜call upon 要求
carbide 碳化物carburzing 渗碳carriage 拖板,大拖板carry along 一起带走
carry down over 从???上取下carry out 完成case hardening 表面硬化
case 壳,套cast steel 铸钢casting 铸造,铸件category 种类caution 警告,警示cavity and core plates 凹模和凸范本
cavity 型腔,腔,洞centre-drilling 中心孔
ceramic 陶瓷制品
chain doted line 点划线channel 信道,信道characteristic 特性
check 核算chip 切屑,铁屑chuck 卡盘chute 斜道circa 大约circlip (开口)簧环circuit 回路,环路circulate (使)循环clamp 夹紧clamp 压板clay 泥土
clearance 间隙clip 切断,夹住cold hobbing 冷挤压cold slug well 冷料井collapse 崩塌,瓦解collapsible 可分解的combination 组合commence 开始,着手
commence 开始commercial 商业的competitive 竞争的complementary 互补的complexity 复杂性complication 复杂化
compression 压缩comprise 包含compromise 妥协,折衷
concern with 关于concise 简明的,简练的confront 使面临
connector 连界面,接头
consequent 随之发生的,必然的
console 控制台
consume 消耗,占用
consummate 使完善
container 容器
contingent 可能发生的
CPU (central processing unit) 中央处理器conventional 常规的
converge 集中于一点
conversant 熟悉的
conversion 换算,转换
conveyer 运送装置
coolant 冷却液
coordinate (使)协调
copy machine 仿形(加工)机床
core 型芯,核心
corresponding 相应的
counteract 反作用,抵抗
couple with 伴随
contour 轮廓
crack (使)破裂,裂纹
critical 临界的
cross-hatching 剖面线
cross-section drawn 剖面图
cross-slide 横向滑板
CRT (cathoder-ray tube) 阴极射线管
crush 压碎
cryogenic 低温学的
crystal 结晶状的
cubic 立方的,立方体的
cup (使)成杯状,引伸
curable 可矫正的
curvature 弧线
curve 使弯曲
cutter bit 刀头,刀片
cyanide 氰化物
complicated 复杂的
dash 破折号
网易电力专业英语词汇(较全) 1)元件设备 三绕组变压器:three-column transformer ThrClnTrans 双绕组变压器:double-column transformer DblClmnTrans 电容器:Capacitor 并联电容器:shunt capacitor 电抗器:Reactor 母线:Busbar 输电线:TransmissionLine 发电厂:power plant 断路器:Breaker 刀闸(隔离开关):Isolator 分接头:tap 电动机:motor 2)状态参数 有功:active power 无功:reactive power 电流:current 容量:capacity 电压:voltage 档位:tap position 有功损耗:reactive loss 无功损耗:active loss 空载损耗:no-load loss 铁损:iron loss 铜损:copper loss 空载电流:no-load current 阻抗:impedance 正序阻抗:positive sequence impedance 负序阻抗:negative sequence impedance 零序阻抗:zero sequence impedance 无功负载:reactive load 或者QLoad 有功负载: active load PLoad 遥测:YC(telemetering) 遥信:YX 励磁电流(转子电流):magnetizing current 定子:stator 功角:power-angle
上限:upper limit 下限:lower limit 并列的:apposable 高压: high voltage 低压:low voltage 中压:middle voltage 电力系统 power system 发电机 generator 励磁 excitation 励磁器 excitor 电压 voltage 电流 current 母线 bus 变压器 transformer 升压变压器 step-up transformer 高压侧 high side 输电系统 power transmission system 输电线 transmission line 固定串联电容补偿fixed series capacitor compensation 稳定 stability 电压稳定 voltage stability 功角稳定 angle stability 暂态稳定 transient stability 电厂 power plant 能量输送 power transfer 交流 AC 装机容量 installed capacity 电网 power system 落点 drop point 开关站 switch station 双回同杆并架 double-circuit lines on the same tower 变电站 transformer substation 补偿度 degree of compensation 高抗 high voltage shunt reactor 无功补偿 reactive power compensation 故障 fault 调节 regulation 裕度 magin 三相故障 three phase fault 故障切除时间 fault clearing time 极限切除时间 critical clearing time 切机 generator triping
一:常用術語 Hon Hai 鴻海 CMM Component module move 機動元件整合 CEM Contract Manu faction service 合約委托代工 IBSC Internet Business Solution Center 國際互聯網應用中心 PCEG Personal Computer Enclosure group 個人電腦外設事業群(FOXTEQ)CCBG Connector& cable business group CPBG Competition business group ESBG Enterprise system business group 鴻富錦事業群 SABG system assembly business group 系統組裝事業群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鴻準 Stamping tool shop I 沖模一廠 Stamping tool shop II 沖模二廠 Prototype workshop 樣品中心 Steel factory 裁剪廠 PCE molding tooling workshop PCE塑模廠 Hua Nan test and measurement center 華南檢測中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 鎂合金 Engineer standard 工標 Document center (database center)資料中心 Design Center 設計中心 Painting 烤漆(廠) Assembly組裝(廠) Stamping 沖壓(廠) Education and Training教育訓練 proposal improvement/creative suggestion提案改善 Technological exchange and study 技術交流研習會 Technology and Development Committee 技術發展委員會 BS Brain Storming 腦力激蕩 QCC Quality Control Circle 品質圈 PDCA Plan Do Check Action 計劃執行檢查總結 DCC delivery control center 交貨管制中心 3C Computer 電腦類產品 Consumer electronics 消費性電子產品 Communication 通訊類產品 Core value(核心价值) Love 愛心
a function of …的函数absorption:吸附acetone 丙酮 acrylics丙烯酸树脂Aerospace 航空agricultural engineering农业工程 agricultural engineer农艺师Amalgam 汞齐,水银;混合物,交叉 ammonia 氨ammonium nitrate硝酸铵ammonium sulfate 硫酸铵analyte分析物analytical chemistry分析化学 amorphous 非定型的,非晶型的,非结晶的,玻璃状的;无一定目的的,乱七八糟approximate to:接近,趋近area 面积argon氩aromatic 芳香烃的 as a whole整体而言ash纯碱asphalt沥青 a priori:先验的,既定的,不根据经验的,由原因推出结果的,演绎的,直觉的 accessory heater 附属加热器accident prevention事故预防 accountant会计师,会计,出纳activity coefficient活度系数 actualrate of absorption 实际吸收速率adiabatic绝热的,不传热的 alkane烷烃ammonia-air mixture 氨气-水混合物 ammonium phosphate磷酸铵anhydrous无水的applied Chemistry应用化学 aquatic plant 水生植物artificial人工的asphaltene沥青油 assay分析化验at right angles to 与…成直角,与…垂直 bottoms product塔底产品baffle-plate折流挡板,缓冲挡板 balance 抵消,平衡barrier障碍物batch间歇的;benzene苯 binary distillation双组分精馏bioengineering生物工程bionics(仿生学) biosynthesis生物合成blower 风机boundary layer 边界层 brick wall 墙壁brittleness 脆性bubble-cap tower 泡罩塔 Buchner funnel 布氏漏斗bulk explosive集装炸药buoyancy force 浮力 by virtue of 由于,根据,凭借于barrel桶(国际原油计量单位) base塔底,基础biological production生物制品生产 biomechanics生物力学bitumen沥青blood-flow dynamics血液流动动力学 boiling point 沸点bottom 底部,塔底branched chain支链烷烃 branched-chain(带支链的)bulk chemical 大宗化工产品 capillary action毛细管作用carbon dioxide 二氧化碳 capital expenditure 基建投资 carbon skeleton碳骨架 capital outlay 费用,成本,基建投资carrier载体 carbon tetrachloride四氯化碳straightforward简单明了的catalyst 催化剂 catalyst催化剂,catalytic cracking 催化裂化 catalytic oxidation催化氧化chemical additive添加剂 centrifuge离心.离心机,离心分离chemical process safety 化工过程安全 chain-shaped链状的chemical reactor transfer of heat, evaporation, crystallization结晶chain链c hlorofluorocarbon二氯二氟化碳,氟里昂 chemical reaction化学反应c irculating gas 循环气 civil engineer土木工程师closed system封闭系统 cleansing agent清洗剂compound化合物 close teamwork紧密的团队协作computer microchip 计算机芯片 coefficient系数concentration difference 浓度差 columnar liquid chromatography柱状液相色谱仪concentration gradient 浓度梯度combustion燃烧condensate冷凝液,凝缩液 commercial proportions 商业规模condensation冷凝
电力电子-专业词汇中英文对照(一) AbsorberCircuit 吸收电路 AC/ACFrequencyConverter 交交变频电路ACpowercontrol交流电力控制ACPowerController交流调功电路ACPowerElectronicSwitch交流电力电子开关AcVoltageController交流调压电路AsynchronousModulation异步调制BakerClampingCircuit贝克箝位电路 Bi-directionalTriodeThyristor双向晶闸管BipolarJunctionTransistor--BJT双极结型晶体管Boost-BuckChopper升降压斩波电路Boost Chopper升压斩波电路BoostConverter升压变换器BridgeReversibleChopper桥式可逆斩波电路BuckChopper降压斩波电路BuckConverter降压变换器Commutation 换流 Conduction Angle 导通角ConstantVoltageConstantFrequency--CVCF 恒压恒频
ContinuousConduction--CCM (电流)连续模式ControlCircuit 控制电路 CukCircuit CUK斩波电路CurrentReversible Chopper 电流可逆斩波电路CurrentSourceTypeInverter--CSTI 电流(源)型逆变电路Cycloconvertor 周波变流器 DC-AC-DC Converter 直交直电路 DCChopping 直流斩波 DCChoppingCircuit 直流斩波电路 DC-DCConverter 直流-直流变换器DeviceCommutation 器件换流DirectCurrentControl 直接电流控制DiscontinuousConductionmode (电流)断续模式displacementfactor 位移因数 distortionpower 畸变功率 doubleendconverter 双端电路 drivingcircuit 驱动电路 electricalisolation 电气隔离 fastactingfuse 快速熔断器 fastrecoverydiode 快恢复二极管fastrevcoveryepitaxialdiodes 快恢复外延二极管
电力电子专业英语 1、元件设备 三绕组变压器:three-column transformer ThrCln Trans 双绕组变压器:double-column transformer DblCl mnTrans 电容器:Capacitor 并联电容器:shunt capacitor 电抗器:Reactor 母线:Bus bar 输电线:Transmission Line 发电厂:power plant 断路器:Breaker 刀闸(隔离开关):Isolator
功角:power-angle 电压等级:voltage grade 空载损耗:no-load loss 铁损:iron loss 铜损:copper loss 空载电流:no-load current 阻抗:impedance 正序阻抗:positive sequence impedance 负序阻抗:negative sequence impedance 零序阻抗:zero sequence impedance 电阻:resistance 电抗:reactance 电导:conductance 电纳:susceptance 导纳:admittance
无功负载:reactive load 或者QLoad 有功负载: active load PLoad 遥测:YC(telemetering) 遥信:YX 励磁电流(转子电流):magnetizing current 定子:stator 功角:power-angle 上限:upper limit 下限:lower limit 并列的:apposable 高压: high voltage 低压:low voltage 中压:middle voltage 电力系统 power system 发电机 generator
A a bit 一个比特a coil of 一圈 a mix of comflicting information 一个混合的相互冲突的信号 a parallel or series circuit 并联成串联回路 abbreviate 缩写abruptly 突然地absolutely summable 完全可求和 absolute绝对 AC 交流accomplish 实现 accumulate 聚集accurately 精确的 acoustic声学acronym 缩写across the open connection point 开路电压actirated simultaneously 同时被激励activation 激励 activation 激活active devices有源器件 active 有源additional term附加项 adequate 适当地adjacent 相邻的adjustable可调的aeronautics 太空学aeronautics and astronautics 航空航天 aircraft飞行器 alarm 警报器 algebra 代数 algorithm 算法 all or nothing 宁为玉碎,不 为瓦全 allow the solution 求解 alter 转换 alternate current 交流 alternatively 或 者 altitude 海拔 amount 量 ampere 安培 amplification factor 放大系数 amplify放大 amplitude 振幅 an electric combination lock 电子号码锁 an exact relation 直接关系 an initial time 初始 analog ics 模 拟集成电路 analog 模拟 analogous fashion 类似的方式中 analogous 相似的 analog类似的 analytic and numerical solution 解析法和数值法求 解过程 anatomical 解 剖,人体解剖学 angle 角度 anisotropic 各 向异性的 annual 年 antenna天线 apparatus仪器 appliance 工具,设 备,装置,仪表 appointed任命 apprenticed学徒 approach进场 appropriate 适合 approuch 接近地面 approximate近似 arbitrary 任意 are also governed 符合 arise 出现,产 生 arithmetic operations 算 法操作 arithmetic 算术 armed force 军 事力量 artery动脉 artificially 人为 地 assemble 组合 associated with 伴随着 Associative Law 结合律 associative 结合 (率) assume假设 astatic needle 无定向磁针 astatic不定向的 astronautics 太 空航空学 astronomically 天 文学的 astronomy天文学 atmospheric 大气 atom 原子 atomic原子 attenuation衰减 audio音频 automotive vehicle 汽车 available to motivate 可用于驱 动 axial轴 B bachelor 学士 back-of-the-envel ope type analysis 黑箱类型的封 装中 back-of-the-envel ope 粗略 bandwidth带宽 bar 横杠 base 基极 basic operatiom 操作 battery 电池 be analogous to 与…相似 be appropriate for 适合 be conservative 保留 be converted into 转换成 be demited as命名 的为 be evaluated被赋 值/被评估 be expanded被扩展 be factored into 被给予系数 be indicated表示 be isotropic各个 同性的 be present in存在 be reduced to归纳 be referred to in terms of flow 被 比喻做流动的形态 be released 放 开 be subject to易遭 受… be supplemented by 被增加 be symbolically denoted with 用…符号表示 beam(光)束 behavior 性能 beta β bias 偏见 binary digit 二 进制数字 binary 二进制 biological 生物学 biomedical engineering生物医 学工程 bipolar transistor 双极管 bipolar 双极型 blacksmith铁匠 block 阻塞 Boltzman波尔兹曼 bookbinder 装 订商 Boolean algebra 布尔代数 Boolean 布尔 bound 跳跃 boundary condition 边界条件 bounded 有界的 bounding surface 边界局面 brackets 方括号 brightness亮度 broadcast广播 building block结 构单元 but rather to 而是 buzzer 蜂鸣器 by a vector 以 矢量方式
课一A Communications 通讯 1. equation n.相等, 平衡, 综合体, 2. communication n. 通信, 通讯, 交通communicate v.沟通, 通信, 3. triode n.三极管 4. storage n. 存储 5.transmission n. 传输, 传送, transmit v. 传输, 转送, 传达, 传导 6. amplifier n.放大器,扩音器 amplify v. 扩大,放大,增强amplification n. 扩大,放大 7. oscillator n.振荡器 8. correlate v. 是相互关联 correlation n.相互关系, 相关(性) 9. transmitter n.发射机 transmit receive transmission reception (发射) (接收) 10.subsequent adj.随后的 课一B Capacitors 电容 1.capacitor n. 电容器 2.capacitance n. 电容量(值) Resistor resistance capacitor capacitance inductor inductance 3. fixed adj. 固定的 variable adj. 可变的 4. dielectric n. 电介质,绝缘材料 adj. 绝缘的 5. relatively adv. 相对地 absolutely adv.绝对地 6. maximum adj. 最大的 n. 最大值 minimum adj. 最小的 n. 最小值 7. farad n. 法(拉) F ohm n. 欧姆Ω Henry n. 亨(利)H 8. trimmer n. 调整者, 整理者, 9. screwdriver n. 螺丝起子,改锥课二A Radio Transmitter无线电发射机 1. radio transmitter 无线电发射机 radio n. 无线电,无线 2. telecommunication n.电信,电信 学,无线电通信 telephone n.电话,电话机 telegraph n.电报, 电报机, 电讯 报 3. transmit v. 传输, 转送, 传达, 传导, 发射, 发报 transmit receive transmission reception transmitter receiver (发射) (接收) 4. intelligence n.信息、情报、智能 information/message n.信息 5. potential adj.潜在的, 可能的, 势 的, n.潜能, 潜力, 电位 6. generate v.产生,发生 generation n.产生, 发生, 一代,7. frequency n.频 low frequency 几个Hz到几十 kHz high frequency 几个MHz到几十 MHz radio frequency 几百MHz到 几个GHz 8. pulse signal 脉冲信号 9. wavelength n.波长用λ表示 10. output n.输出,产量 input n.输入 11. band n. 带,波段,频带 课二B Electromotive Force 电动势 1. electromotive adj.电动的,电动 势的 electromotive force 电动势 2.driving adj.驱动的 driving force n. 驱动力 driving unit 传动装置 3. volt n. 伏特 4. distinguish v.区分 5. potential difference 电位差 课三A Time Constant 时常数 1.nuclear adj.原子能的, n.核武器, 有核国 nuclear arms 核武 nuclear energy 核能 2.constant n.常数 adj.不断, 不断的, time constant 时间常数 3. instantaneously adv.瞬间地,即刻 instant n.瞬息, 一会儿, 时刻 4. dependent adj. 依赖的,依赖于,取决 于 5. capacitive adj.电容的,容性的 capacitor n.电容器 capacitance n.电容值 6.discharge n.放电v.放电 charge n.电荷,充电v.充电 7.universal 普遍的, 全体的, 通用的, 课三B RL Time Constant RL时序常数 1.inductor n.电感器 inductance n.电感值(量) inductive adj.感应的; 电感的 2. function n.功能, 函数,作用, 3. Decay n.衰减v. 衰减 decay constant 衰减常数 decay factor 衰减因子 4. reverse adj.反向的, 相反, 逆转的 5. peak value 峰值
CORPORATE COMMON ABBREVIATION 常用语缩写 1 Organization组织 1-1 HQ Head Quarter 总公司 1-2Chairmen主席 1-3Lite-On Group光宝集团 1-4 President 总裁 1-5Executive Vice President 常务副总裁 1-6Vice President副总裁 1-7HR Human Resource人力资源部 1-8FIN Finance 财务 1-9Sales 销售 1-10R&D Research & Developing 研发部 1-11QA 质量保证QA DQA CS 1-12MIS Management Information System资讯管理系统1-13Pur 采购Purchasing 1-14IMD Image management division 影像管理事业部 1-15ITS information technology system 计算机部 1-16QRA quality reliability assurance 品保部 1-17MFG manufacturing 制造部 1-18PMC production &material control 生(产)物(料)管(理) 1-19 PRO Procuremnet 采购开发部
1-20 PMO Plant Manager Office 厂长室 1-21 CEO Chief Executive Officer 执行总裁 2 Materials 材料 2-1PC Production Control 生产控制 2-1-1MPS Mass Production Schedule 量产计划 2-1-2FGI Finished goods Inventory 成品存货 2-1-3UTS Units To Stock存货单元 2-1-4WIP Working In Process Inventory在制品 2-1-5C/T Cycle Time 循环时间,瓶颈 2-1-6WD Working Days 工作天 2-1-7MTD Month To Days 月初到今日(例如总表整理) 2-1-8YTD Year To Days 年初到今日 2-1-9 SO Sales Order 销售单 2-1-10MO Manufacture Order 制造单 2-1-11 BTO Build To Order 订单生产 2-1-12 P/N part number 料号 2-1-13 FCST Forecast 预测计划 2-1-14 W/O Working Order 工单 2-1-15 P/O Purchasing Order 采购单 2-1-16 VDS Vendor Delivery Schedule 厂商送货进度表2-1-17 D/C Delivery Order 交货单 2-2 MC Material Control材料控制
transistor n 晶体管 diode n 二极管semiconductor n 半导体 resistor n 电阻器 capacitor n 电容器 alternating adj 交互的 amplifier n 扩音器,放大器integrated circuit 集成电路 linear time invariant systems 线性时不变系统voltage n 电压,伏特数 tolerance n 公差;宽容;容忍condenser n 电容器;冷凝器dielectric n 绝缘体;电解质electromagnetic adj 电磁的 adj 非传导性的 deflection n偏斜;偏转;偏差 linear device 线性器件 the insulation resistance 绝缘电阻 anode n 阳极,正极 cathode n 阴极 breakdown n 故障;崩溃 terminal n 终点站;终端,接线端emitter n 发射器 collect v 收集,集聚,集中insulator n 绝缘体,绝热器oscilloscope n 示波镜;示波器 gain n 增益,放大倍数 forward biased 正向偏置 reverse biased 反向偏置 P-N junction PN结 MOS(metal-oxide semiconductor)金属氧化物半导体 enhancement and exhausted 增强型和耗尽型 integrated circuits 集成电路 analog n 模拟 digital adj 数字的,数位的horizontal adj, 水平的,地平线的vertical adj 垂直的,顶点的amplitude n 振幅,广阔,丰富attenuation n衰减;变薄;稀薄化multimeter n 万用表 frequency n 频率,周率 the cathode-ray tube 阴极射线管 dual-trace oscilloscope 双踪示波器 signal generating device 信号发生器 peak-to-peak output voltage 输出电压峰峰值sine wave 正弦波 triangle wave 三角波 square wave 方波 amplifier 放大器,扩音器 oscillator n 振荡器 feedback n 反馈,回应 phase n 相,阶段,状态 filter n 滤波器,过滤器 rectifier n整流器;纠正者 band-stop filter 带阻滤波器 band-pass filter 带通滤波器 decimal adj 十进制的,小数的hexadecimal adj/n十六进制的 binary adj 二进制的;二元的octal adj 八进制的 domain n 域;领域 code n代码,密码,编码v编码 the Fourier transform 傅里叶变换 Fast Fourier Transform 快速傅里叶变换microcontroller n 微处理器;微控制器assembly language instrucions n 汇编语言指令 chip n 芯片,碎片 modular adj 模块化的;模数的 sensor n 传感器 plug vt堵,塞,插上n塞子,插头,插销coaxial adj 同轴的,共轴的 fiber n 光纤relay contact 继电接触器 single instruction programmer 单指令编程器 dedicated manufactures programming unit 专 供制造厂用的编程单元 beam n (光线的)束,柱,梁 polarize v(使)偏振,(使)极化 Cathode Ray Tube(CRT)阴极射线管 neuron n神经元;神经细胞 fuzzy adj 模糊的 Artificial Intelligence Shell 人工智能外壳程序 Expert Systems 专家系统 Artificial Intelligence 人工智能 Perceptive Systems 感知系统 neural network 神经网络 fuzzy logic 模糊逻辑 intelligent agent 智能代理 electromagnetic adj 电磁的 coaxial adj 同轴的,共轴的 microwave n 微波 charge v充电,使充电 insulator n 绝缘体,绝缘物 nonconductive adj非导体的,绝缘的 antenna n天线;触角 modeling n建模,造型 simulation n 仿真;模拟 prototype n 原型 array n 排队,编队 vector n 向量,矢量 wavelet n 微波,小浪 sine 正弦cosine 余弦 inverse adj倒转的,反转的n反面;相反v 倒转 high-performance 高精确性,高性能 two-dimensional 二维的;缺乏深度的 three-dimensional 三维的;立体的;真实的 object-oriented programming面向对象的程序 设计 spectral adj 光谱的 attenuation n衰减;变薄;稀释 distortion n 失真,扭曲,变形 wavelength n 波长 refractive adj 折射的 ATM 异步传输模式Asynchronous Transfer Mode ADSL非对称用户数字线Asymmetric digital subscriber line VDSL甚高速数字用户线very high data rate digital subscriber line HDSL高速数据用户线high rate digital subscriber line FDMA频分多址(Frequency Division Multiple Access) TDMA时分多址(Time Division Multiple Access) CDMA同步码分多址方式(Code Division Multiple Access) WCDMA宽带码分多址移动通信系统(Wideband Code Division Multiple Access) TD-SCDMA(Time Division Synchronous Code Division Multiple Access)时分同步码分多址 SDLC(synchronous data link control)同步数据 链路控制 HDLC(high-level data link control)高级数据链路 控制 IP/TCP(internet protocol /transfer Control Protocol)网络传输控制协议 ITU (International Telecommunication Union) 国际电信联盟 ISO国际标准化组织(International Standardization Organization); OSI开放式系统互联参考模型(Open System Interconnect) GSM全球移动通信系统(Global System for Mobile Communications) GPRS通用分组无线业务(General Packet Radio Service) FDD(frequency division duplex)频分双工 TDD(time division duplex)时分双工 VPI虚路径标识符(Virtual Path Identifier); ISDN(Integrated Services Digital Network)综 合业务数字网 IDN综合数字网(integrated digital network) HDTV (high definition television)高清晰度电视 DCT(Discrete Cosine Transform)离散余弦变换 VCI(virtual circuit address)虚通路标识 MAN城域网Metropolitan area networks LAN局域网local area network WAN广域网wide area network 同步时分复用STDM Synchronous Time Division Multiplexing 统计时分复用STDM Statistical Time Division Multiplexing 单工传输simplex transmission 半双工传输half-duplex transmission 全双工传输full-duplex transmission 交换矩阵Switching Matrix 电路交换circuit switching 分组交换packet switching 报文交换message switching 奇偶校验parity checking 循环冗余校验CRC Cyclic Redundancy Check 虚过滤Virtual filter 数字滤波digital filtering 伪随机比特Quasi Random Bit 带宽分配Bandwidth allocation 信源information source 信宿destination 数字化digitalize 数字传输技术Digital transmission technology 灰度图像Grey scale images 灰度级Grey scale level 幅度谱Magnitude spectrum 相位谱Phase spectrum 频谱frequency spectrum 智能设备Smart Device 软切换Soft handover 硬切换Hard Handover 相干检测Coherent detection 边缘检测Edge detection 冲突检测collision detection 业务集合service integration 业务分离/综合service separation/ integration 网络集合network integration 环形网Ring networks 令牌环网Token Ring network 网络终端Network Terminal 用户终端user terminal 用户电路line circuit 电路利用率channel utilization(通道利用率) 相关性coherence 相干解调coherent demodulation 数字图像压缩digital image compression 图像编码image encoding 有损/无损压缩lossy/lossless compression 解压decompression 呼叫控制Call Control 误差控制error control 存储程序控制stored program control 存储转发方式store-and-forward manner 语音\视频传输voice\video transmission 视频点播video-on-demand(VOD) 会议电视Video Conference 有线电视cable television 量化quantization 吞吐量throughput 话务量traffic 多径分集Multipath diversity 多媒体通信MDM Multimedia Communication 多址干扰Multiple Access Interference 人机交互man machine interface 交互式会话Conversational interaction
电力系统power system 发电机generator 励磁excitation 励磁器exciter电压voltage 电流current 升压变压器step-up transformer 母线bus 变压器transformer 空载损耗:no-load loss铁损:iron loss 铜损:copper loss 空载电流:no-load current无功损耗:reactive loss有功损耗:active loss 输电系统power transmission system 高压侧high side 输电线transmission line 高压: high voltage低压:low voltage 中压:middle voltage 功角稳定angle stability稳定stability 电压稳定voltage stability 暂态稳定transient stability 电厂power plant 能量输送power transfer 交流AC直流DC 电网power system 落点drop point 开关站switch station 调节regulation 高抗high voltage shunt reactor并列的:apposable 裕度margin 故障fault 三相故障three phase fault分接头:tap 切机generator triping 高顶值high limited value 静态static (state) 动态dynamic (state)自动电压调节器AVR Automatic voltage regulator 电抗reactance 电阻resistance 功角power angle 有功(功率)active power 电容器:Capacitor电抗器:Reactor 断路器:Breaker 电动机:motor 功率因数:power-factor 定子:stator 阻抗电压:阻抗:impedance功角:power-angle 电压等级:voltage grade 有功负载: active load/PLoad无功负载:reactive load档位:tap position 电阻:resistor电抗:reactance 电导:conductance 电纳:susceptance上限:upper limit 下限:lower limit 正序阻抗:positive sequence impedance负序阻抗:negative sequence impedance零序阻抗:zero sequence impedance 无功(功率)reactive power功率因数power factor 无功电流reactive current 斜率slope额定rating 变比ratio 参考值reference value电压互感器PT 分接头tap 仿真分析simulation analysis下降率droop rate 传递函数transfer function 框图block diagram受端receive-side 同步synchronization 保护断路器circuit breaker 摇摆swing 阻尼damping 无刷直流电机:Brushless DC motor 刀闸(隔离开关):Isolator机端generator terminal 变电站transformer substation 永磁同步电机:Permanent-magnet Synchronism Motor 异步电机:Asynchronous Motor 三绕组变压器:three-column transformer ThrClnTrans 双绕组变压器:double-column transformer DblClmnTrans 固定串联电容补偿fixed series capacitor compensation 双回同杆并架double-circuit lines on the same tower 单机无穷大系统one machine - infinity bus system 励磁电流:magnetizing current 补偿度degree of compensation Electromagnetic fields 电磁场失去同步loss of synchronization 装机容量installed capacity无功补偿reactive power compensation故障切除时间fault clearing time 极限切除时间critical clearing time 强行励磁reinforced excitation 并联电容器:shunt capacitor < 下降特性droop characteristics 线路补偿器LDC(line drop compensation) 电机学Electrical Machinery 自动控制理论Automatic Control Theory电磁场Electromagnetic Field微机原理Principle of Microcomputer 电工学Electrotechnics Principle of circuits 电路原理Electrical Machinery 电机学 电力系统稳态分析Steady-State Analysis of Power System 电力系统暂态分析Transient-State Analysis of Power System 电力系统继电保护原理Principle of Electrical System’s Relay Protection 电力系统元件保护原理Protection Principle of Power Syste m’s Element