齿轮术语中英文对照表
第一组公差
第二组公差
第三组公差
阿基米德蜗杆Archimedes worm
安全系数safety factor; factor of safety
安全载荷safe load
变形deformation
摆线齿轮cycloidal gear
摆线齿形cycloidal tooth profile
背锥角back angle
背锥距back cone distance
比例尺scale
变速speed change
变速齿轮change gear ; change wheel
变位齿轮modified gear
变位系数modification coefficient
标准齿轮standard gear
标准直齿轮standard spur gear
表面粗糙度surface roughness
不完全齿轮机构intermittent gearing
补偿compensation
参数化设计parameterization design, PD
残余应力residual stress
操纵及控制装置operation control device
槽数Geneva numerate
侧隙backlash
差动轮系differential gear train
差动螺旋机构differential screw mechanism
差速器differential
常用机构conventional mechanism; mechanism in common use 承载量系数bearing capacity factor
承载能力bearing capacity
成对安装paired mounting
尺寸系列dimension series
齿槽tooth space
齿槽宽spacewidth
齿侧间隙backlash
齿顶高addendum
齿顶圆addendum circle
齿根高dedendum
齿根圆dedendum circle
齿厚tooth thickness
齿距circular pitch
齿宽face width
齿廓tooth profile
齿廓曲线tooth curve
齿轮gear
齿轮变速箱speed-changing gear boxes
齿轮齿条机构pinion and rack
齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter
齿轮机构gear
齿轮轮坯blank
齿轮传动系pinion unit
齿轮联轴器gear coupling
齿条传动rack gear
齿数tooth number
齿数比gear ratio
齿条rack
齿条插刀rack cutter; rack-shaped shaper cutter
齿形链、无声链silent chain
齿形系数form factor
齿式棘轮机构tooth ratchet mechanism
插齿机gear shaper
重合点coincident points
重合度contact ratio
传动比transmission ratio, speed ratio
传动装置gearing; transmission gear
传动系统driven system
传动角transmission angle
传动轴transmission shaft
创新设计creation design
垂直载荷、法向载荷normal load
从动带轮driven pulley
从动件driven link, follower
从动件平底宽度width of flat-face
从动件停歇follower dwell
从动件运动规律follower motion
从动轮driven gear
粗线bold line
粗牙螺纹coarse thread
大齿轮gear wheel
打滑slipping
带传动belt driving
单列轴承single row bearing
单位矢量unit vector
当量齿轮equivalent spur gear; virtual gear
当量齿数equivalent teeth number; virtual number of teeth 当量摩擦系数equivalent coefficient of friction
当量载荷equivalent load
刀具cutter
导数derivative
倒角chamfer
导程lead
导程角lead angle
等效质量equivalent mass
(疲劳)点蚀pitting
垫圈gasket
垫片密封gasket seal
顶隙bottom clearance
定轴轮系ordinary gear train; gear train with fixed axes
动力学dynamics
动密封kinematical seal
动能dynamic energy
动力粘度dynamic viscosity
动力润滑dynamic lubrication
动载荷dynamic load
端面transverse plane
端面参数transverse parameters
端面齿距transverse circular pitch
端面齿廓transverse tooth profile
端面重合度transverse contact ratio
端面模数transverse module
端面压力角transverse pressure angle
锻造forge
惰轮idle gear
额定寿命rating life
额定载荷load rating
发生线generating line
发生面generating plane
法面normal plane
法面参数normal parameters
法面齿距normal circular pitch
法面模数normal module
法面压力角normal pressure angle
法向齿距normal pitch
法向齿廓normal tooth profile
法向直廓蜗杆straight sided normal worm
法向力normal force
反正切Arctan
范成法generating cutting
仿形法form cutting
非标准齿轮nonstandard gear
非接触式密封non-contact seal
非周期性速度波动aperiodic speed fluctuation
非圆齿轮non-circular gear
粉末合金powder metallurgy
分度线reference line; standard pitch line
分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder
分度圆柱螺旋角helix angle at reference cylinder
分母denominator
分子numerator
分度圆锥reference cone; standard pitch cone
封闭差动轮系planetary differential
复合应力combined stress
复式螺旋机构Compound screw mechanism
干涉interference
刚度系数stiffness coefficient
钢丝软轴wire soft shaft
根切undercutting
公称直径nominal diameter
高度系列height series
功work
工况系数application factor
工艺设计technological design
工作循环图working cycle diagram
工作机构operation mechanism
工作载荷external loads
工作空间working space
工作应力working stress
工作阻力effective resistance
工作阻力矩effective resistance moment
公法线common normal line
公制齿轮metric gears
功率power
功能分析设计function analyses design
共轭齿廓conjugate profiles
共轭凸轮conjugate cam
惯性力矩moment of inertia ,shaking moment
惯性力平衡balance of shaking force
冠轮crown gear
轨迹生成path generation
轨迹发生器path generator
滚刀hob
过度切割undercutting
耗油量oil consumption
耗油量系数oil consumption factor
横坐标abscissa
互换性齿轮interchangeable gears
花键spline
滑键、导键feather key
滑动率sliding ratio
环面蜗杆toroid helicoids worm
缓冲装置shocks; shock-absorber
机械machinery
机械平衡balance of machinery
机械设计machine design; mechanical design
机械特性mechanical behavior
机械调速mechanical speed governors
机械效率mechanical efficiency
机械原理theory of machines and mechanisms
机械无级变速mechanical stepless speed changes 基础机构fundamental mechanism
基本额定寿命basic rating life
基于实例设计case-based design,CBD
基圆base circle
基圆半径radius of base circle
基圆齿距base pitch
基圆压力角pressure angle of base circle
基圆柱base cylinder
基圆锥base cone
极限位置extreme (or limiting) position
极位夹角crank angle between extreme (or limiting) positions
计算机辅助设计computer aided design, CAD
计算机辅助制造computer aided manufacturing, CAM
计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment
计算弯矩calculated bending moment
间隙backlash
减速比reduction ratio
减速齿轮、减速装置reduction gear
减速器speed reducer
渐开螺旋面involute helicoid
渐开线involute
渐开线齿廓involute profile
渐开线齿轮involute gear
渐开线发生线generating line of involute
渐开线方程involute equation
渐开线函数involute function
渐开线蜗杆involute worm
渐开线压力角pressure angle of involute
渐开线花键involute spline
键key
键槽keyway
交变应力repeated stress
交变载荷repeated fluctuating load
交叉带传动cross-belt drive
交错轴斜齿轮crossed helical gears
胶合scoring
角速度angular velocity
角速比angular velocity ratio
结构structure
结构设计structural design
截面section
节点pitch point
节距circular pitch; pitch of teeth
节线pitch line
节圆pitch circle
节圆齿厚thickness on pitch circle
节圆直径pitch diameter
节圆锥pitch cone
节圆锥角pitch cone angle
解析设计analytical design
紧边tight-side
紧固件fastener
径节diametral pitch
径向radial direction
径向当量动载荷dynamic equivalent radial load
径向当量静载荷static equivalent radial load
径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating
径向接触轴承radial contact bearing
径向平面radial plane
径向游隙radial internal clearance
径向载荷radial load
径向载荷系数radial load factor
径向间隙clearance
静力static force
静平衡static balance
静载荷static load
绝对运动absolute motion
绝对速度absolute velocity
可靠性reliability
可靠性设计reliability design, RD
理论廓线pitch curve
理论啮合线theoretical line of action
力矩moment
力平衡equilibrium
力偶couple
力偶矩moment of couple
轮坯blank
螺旋副helical pair
螺旋机构screw mechanism
螺旋角helix angle
螺旋线helix ,helical line
模块化设计modular design, MD 模数module
磨损abrasion ;wear; scratching 耐磨性wear resistance
内齿轮internal gear
内齿圈ring gear
内力internal force
内圈inner ring
啮合engagement, mesh, gearing 啮合点contact points
啮合角working pressure angle
啮合线line of action
啮合线长度length of line of action 盘形转子disk-like rotor
抛物线运动parabolic motion
疲劳极限fatigue limit
疲劳强度fatigue strength
偏置式offset
偏( 心) 距offset distance
偏心率eccentricity ratio
偏心质量eccentric mass
偏距圆offset circle
偏心盘eccentric
切齿深度depth of cut
曲齿锥齿轮spiral bevel gear
曲率curvature
曲率半径radius of curvature
曲面从动件curved-shoe follower 曲线运动curvilinear motion
全齿高whole depth
权重集weight sets
球面副spheric pair
球面渐开线spherical involute
球面运动spherical motion
人字齿轮herringbone gear
润滑装置lubrication device
润滑lubrication
三角形花键serration spline
三角形螺纹V thread screw
少齿差行星传动planetary drive with small teeth difference 升程rise
升距lift
实际廓线cam profile
输出轴output shaft
实际啮合线actual line of action
双曲面齿轮hyperboloid gear
顺时针clockwise
瞬心instantaneous center
死点dead point
太阳轮sun gear
特性characteristics
图册、图谱atlas
图解法graphical method
退火anneal
陀螺仪gyroscope
外力external force
外形尺寸boundary dimension
网上设计on-net design, OND
微动螺旋机构differential screw mechanism
位移displacement
蜗杆worm
蜗杆传动机构worm gearing
蜗杆头数number of threads
蜗杆直径系数diametral quotient
蜗杆蜗轮机构worm and worm gear
蜗杆形凸轮步进机构worm cam interval mechanism
蜗杆旋向hands of worm
蜗轮worm gear
无级变速装置stepless speed changes devices
相对速度relative velocity
相对运动relative motion
相对间隙relative gap
象限quadrant
橡皮泥plasticine
小齿轮pinion
小径minor diameter
谐波齿轮harmonic gear
谐波传动harmonic driving
斜齿轮的当量直齿轮equivalent spur gear of the helical gear 心轴spindle
行程速度变化系数coefficient of travel speed variation
行程速比系数advance-to return-time ratio
行星齿轮装置planetary transmission
行星轮planet gear
行星轮变速装置planetary speed changing devices
行星轮系planetary gear train
旋转运动rotary motion
压力角pressure angle
应力图stress diagram
应力—应变图stress-strain diagram
优化设计optimal design
油杯oil bottle
有效圆周力effective circle force
圆带传动round belt drive
圆弧齿厚circular thickness
圆弧圆柱蜗杆hollow flank worm
圆角半径fillet radius
圆盘摩擦离合器disc friction clutch
圆盘制动器disc brake
原动机prime mover
原始机构original mechanism
圆形齿轮circular gear
圆柱滚子cylindrical roller
圆柱滚子轴承cylindrical roller bearing
圆柱副cylindric pair
圆柱蜗杆cylindrical worm
圆锥滚子tapered roller
圆锥滚子轴承tapered roller bearing
圆锥齿轮机构bevel gears
圆锥角cone angle
运动副kinematic pair
运动粘度kenematic viscosity
载荷load
展成法generating
直齿圆柱齿轮spur gear
直齿锥齿轮straight bevel gear
直径系数diametral quotient
直径系列diameter series
直廓环面蜗杆hindley worm
质量mass
中心距center distance
中心距变动center distance change
中径mean diameter
终止啮合点final contact, end of contact
周节pitch
轴shaft
轴承盖bearing cup
轴承合金bearing alloy
轴承座bearing block
轴承外径bearing outside diameter
轴颈journal
轴瓦、轴承衬bearing bush
轴端挡圈shaft end ring
轴环shaft collar
轴肩shaft shoulder
轴角shaft angle
轴向axial direction
轴向齿廓axial tooth profile
转动副revolute (turning) pair
转速swiveling speed ; rotating speed
转轴revolving shaft
转子rotor
装配条件assembly condition
锥齿轮bevel gear
锥顶common apex of cone
锥距cone distance
锥轮bevel pulley; bevel wheel
锥齿轮的当量直齿轮equivalent spur gear of the bevel gear 锥面包络圆柱蜗杆milled helicoids worm
准双曲面齿轮hypoid gear
自由度degree of freedom, mobility
总重合度total contact ratio
总反力resultant force
总效率combined efficiency; overall efficiency
组成原理theory of constitution
组合齿形composite tooth form
组合安装stack mounting
最少齿数minimum teeth number
最小向径minimum radius 作用力applied force
坐标系coordinate frame
塑胶模具类中英文对照专业术语工程部/ Design department: 1) Designer - 设计师。 2) Assembly drawing - 模具组装图。 3) Mold layout - 模具结构图。 4) 2D product drawing - 2D产品图。 5) 3D product data - 3D产品数据。 6) Part drawing - 散件图。 7) Insert molding - 镶件模。 8) 2 color mold / Double injection tool - 双色模。 9) Hydraulic system - 油/水压系统。 10) Parting line - 分模线。 11) Air venting - 排气槽。 12) Cooling system - 冷却系统。 13) Screw - 镙丝。 14) Hot runner system - 热流道。 15) Valve gate - 伐针入水口。 16) Fan gate - 扇型入水口。 17) Pin point gate - 针点进胶。 18) Moon gate / Banana gate - 香蕉,象牙入水口。 19) Submarine gate - 潜水口。 20) Injection machine tonnage - 注塑机吨数。 21) Number of cavity - 穴数。 22) Steel - 钢材。 23) Copper - 铜。 24) Tungsten copper - 钨铜。 25) Beryllium copper - 铍铜。 26) Hardening - 加硬/淬火。 27) Tempering - 回火。
财务专业术语中英文对照表 英文中文说明 Account Accounting system 会计系统 American Accounting Association 美国会计协会 American Institute of CPAs 美国注册会计师协会 Audit 审计 Balance sheet 资产负债表 Bookkeepking 簿记 Cash flow prospects 现金流量预测 Certificate in Internal Auditing 部审计证书 Certificate in Management Accounting 管理会计证书 Certificate Public Accountant注册会计师 Cost accounting 成本会计 External users 外部使用者 Financial accounting 财务会计 Financial Accounting Standards Board 财务会计准则委员会 Financial forecast 财务预测 Generally accepted accounting principles 公认会计原则 General-purpose information 通用目的信息 Government Accounting Office 政府会计办公室 Income statement 损益表 Institute of Internal Auditors 部审计师协会 Institute of Management Accountants 管理会计师协会 Integrity 整合性 Internal auditing 部审计 Internal control structure 部控制结构 Internal Revenue Service 国收入署 Internal users部使用者 Management accounting 管理会计 Return of investment 投资回报 Return on investment 投资报酬 Securities and Exchange Commission 证券交易委员会
AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT) AD直径:指胎面中心线直径(EU)。又叫T直径(GT) Auto-lock Ear A Lug on the cone ring used to mount the mold/container in the top half of a 60“ NRM Auto-lock press. 导环上的突缘,用于和60“ NRM Auto-lock 硫化机上半部连接。 Bead Ring The tire bead forming ring (also: toe ring) 钢圈,也称toe ring Bead Ring Register The landing and tapered seat that the bead ring fits into 钢圈配合:侧板上,和钢圈配合的平面及锥面 Bottom Container Plate The plate that the bottom sidewall plate is bolted to 模壳底座 Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes used for lifting. 模壳底座吊耳:装配在底座上、有水平的孔,用来吊装的吊耳 Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing. 装配在底座上,用来支承定位销套的突缘 Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press. 用来将底座装配在硫化机上的突缘 Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding. 分离钩:固定在花纹块底部的钩子,轮胎硫化完后若花纹块不能跟轮胎分离,就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。
Chemntherapeutic agents 化学疗法 thus xue fiao fa) Chemothcrjipy 化学疔,Z (hija xue Aaa fa) hns the goal of killing or stopping rhe development nf rapidly dividing cells. Examples are Cisplatin, Carboplat in, Bkomycin I 博来霉嗪1 (ftd l3f Sg S-fltinrncjrao 5 氟尿瞪喘(ft/ HiAO m dfinfl), mrthotrExate 甲員媒时{Jia 的 did /ioffk Vincristine fifr chun xJTj/a^, Vinblastine 衣祚碱 (chang chun ;ian}. Taxol and Tawiuvirtn .木戟题(SSfi ben 阳ng 钠* Since the sanK nicchanism (hat kilh malignant cdl or blocks de vela pment of a malignant cell cm have similar effects on a nnrnuil, rap idly dividing celt any of LhcNt agents ciin hax r c btid side clfccts. Some terms of cancer ircitLcd with chemcthera 卩、may cjus,e ihe cancer (o "disappear
1. 热力学thermodynamics 2. 热源heat source 3. 热力学平衡状态thermodynamic equilibrium state 4. 稳态steady state 5. 非稳态unsteady state 6. 可逆过程reversible process 7. 不可逆过程irreversible process 8. 热力学第一定律first law of thermodynamics 9. 热力学第二定律second law of thermodynamics 10. 热力学第三定律third law of thermodynamics 11. 内能internal energy 12. 焓enthalpy 13. 熵entropy 14. 热量heat 15. 理想气体ideal gas 16. 相变change of phase 17. 汽化vaporization 18. 蒸发evaporation 19. 沸腾boiling 20. 沸点boiling point 21. 凝结condensation 22. 饱和状态saturation state
23. 饱和温度saturation temperature 24. 饱和压力saturation pressure 25. 饱和液体saturation liquid 26. 饱和蒸汽saturation vapor 27. 过饱和supersaturation 28. 湿蒸汽wet vapor 29. 过热superheat 30. 过热蒸汽superheated vapor 31. 过热度degree of superheat 32. 过冷subcooling 33. 过冷液体subcooled liquid 34. 气-液混合物liquid-vapor mixture 35. 干度quality 36. 冷凝点condensation point 37. 冷凝液condensate 38. 共沸混合物azeotropic mixture 39. 共沸性azeotropy 40. 共沸点azeotropic point 41. 凝固solidification 42. 熔化fusion 43. 熔点melting point 44. 升华sublimation
语文课程与教学论 名词术语中英文对照表 the Chinese Course and Teaching and Learning Theory in Chinese and English Teaching materials editing teaching materials /Chinese Teaching Materials /edit teaching materials /Uniformed Chinese Teaching Materials /Experimental Teaching Materials /Mother Tongue Teaching Materials /Teaching Materials of the New Course *textbook *reading book *teaching reference book *exercises book *studying plan Technology /Educational Technology /Modern Educational Technology /Educational Technology in Chinese Teaching /multi-media technology /net technology /cloud serving technology *white board *net meeting *chat room *blog Teaching Basic Theory of the Teaching teaching aim teaching task teaching objective teaching model teaching tactics teaching principle teaching program teaching reform teaching case Courseware teaching resources teaching experiment /mother tongue teaching A Term List of 1. 教材( JC ) 教材编写 /语文教材 /编写教材 / 统编教材 /实验教材 /母语教材 /新课程教材 * 课本 * 读本 * 教学参考书(教参) * 练习册 *学案 2. 技术( JS ) / 教育技术 /现代 教育技术 /语文 教育技术 /多媒 体技术 / 网络 技术 /云服务技 术 * 白板 *网 络会议 *聊天室 * 博克 3. 教学 (JX ) 教学基本理论 教学目的 教学 任务 教学目标 教学模式 教学 策略 教学原则 教学大纲 教学 改革 教学案例 教学课件 教学 资源 教学实验 /母语教学
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机(尼龙拉勾)n yl on latch lock 45斜顶lifter 46模胚(架)mold base 47母模cavity in sert 48公模core insert 49行位(滑块)slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
各种专业名称英语词汇中英文对照表
————————————————————————————————作者: ————————————————————————————————日期: ?
各种专业名称英语词汇中英文对照表 哲学Philosophy 马克思主义哲学Philosophy of Marxism 中国哲学ChinesePhilosophy 外国哲学ForeignPhilosophies ?逻辑学Logic?伦理学Ethics 美学Aesthetics 宗教学Science of Religion?科学技术哲学Philosophy of Science andTechnology?经济学Economics?理论经济学Theoretical Economics ?政治经济学PoliticalEconomy ?经济思想史History ofEconomic Thought ?经济史History of Economic 西方经济学WesternEconomics?世界经济World Economics ?人口、资源与环境经济学Population,Resources andEnvironmentalEconomics 应用经济学Applied Economics 国民经济学National Economics?区域经济学Regional Economics ?财政学(含税收学)Public Finance (includingTaxation) 金融学(含保险学) Finance (including Insurance)?产业经济学Industrial Economics ?国际贸易学International Trade 劳动经济学Labor Economics ?统计学Statistics ?数量经济学Quantita tive Economics ?中文学科、专业名称英文学科、专业名称 国防经济学National Defense Economics?法学Law 法学Science of Law ?法学理论Jurisprudence?法律史Legal History ?宪法学与行政法学Constitutional Law and Administrative Law 刑法学Criminal Jurisprudence 民商法学(含劳动法学、社会保障法学)Civil Law and Commercial Law (i ncluding Science of LabourLawand Science ofSocial Sec urityLaw)?诉讼法学Science of ProcedureLaws ?经济法学Sc ience ofEconomic Law ?环境与资源保护法学Science ofEnvironment andNatural Resources Protection Law 国际法学(含国际公法学、国际私法学、国际经济法学、)Internationallaw (including International Public law, International PrivateLaw a
仓库专业术语参考中英 文对照 Company Document number:WTUT-WT88Y-W8BBGB-BWYTT-19998
收发存专用的英语大全; 收货组ReceivingTeam; 收货区ReceivingArea; 散装区BulkStorage; 货架区RackStorage; 入库Entry; 入库单"Warehouseentry;"; 收货单ReceivingNote; 收货产品ReceivingProduct; 物品接收时间GoodsReceiveDate;物品数仓库收发存专用的英语大全 收货组ReceivingTeam 收货区ReceivingArea 散装区BulkStorage 货架区RackStorage 入库Entry 入库单"Warehouseentry"
收货单ReceivingNote 收货产品ReceivingProduct 物品接收时间GoodsReceiveDate 物品数量总计GoodsTotalMaterialQuantity重量weight 毛重GrossWeight 净重NetWeight 最大重量MaximumWeight 最小重量MiximumWeight 总计容量TotalCapacity 出库单DeliveryList 拣货PickingGoods 拣货区PickingArea 转储单TransferOrder 检验报告单InspectionDocument 物料清单BillofMaterial 料号PartNumber 电子单据ElectronicsNote
码盘Pallet-Sorting 分拣Picking/Sorting 采购订单PurchaseOrder(PO)手写单HandNote 到货通知ArrivalNotice 报关到货ImportingGoods 检验单InspectionNote 入库扫描EntryScanning 扫描Scan 存货InStock 冻结的BlockedStock 库存Inventory/Stock 库存清单StockList 发货区ShippingArea 发货单Deliverysheet 盘点Count 日盘DailyCount
工程专业术语中英文对照
CDB工程专业术语中英文对照(二) 添加时间:2013-4-24 节流截止放空阀 2011-08-10 16:50:46| 分类:English | 标签:|字号大中小订阅 六、仪表及自动控制 通用描述 COMMON DESCRIPTION 设备名称Equipment Name 缩写 ABB. 分散控制系统Distributed Control System DCS 安全仪表系统Safety Instrumentation System SIS 紧急切断系统Emergency Shutdown system ESD 火气系统Fire and Gas system F&G 监视控制和数据采集系统 Supervisory Control and Data Acquisition SCADA 可编程逻辑控制器Programmed Logic Controller PLC 远程终端单元Remote Terminal Unit RTU 站控系统Station Control System SCS 中央控制室Central Control Room CCR 操作间Operation room 机柜间Equipment room/ Cabinet room 大屏显示系统Large Screen Display system LSD 流量类仪表 FLOW INSTRUMENT 设备名称Equipment Name 孔板Orifice Plate 文丘里流量计Venturi Flowmeter 均速管流量计Averaging Pitot Tube 阀式孔板节流装置 Orifice Plate in quick change fitting 涡轮流量计Turbine Flowmeter
LN3--PU/Phylon/Rubber Process Contents for these three sections of English Version PFC: ?Phylon Work Sheet PH数据表 ?Components Specification Sheet(Phylon) 部件明细单(Phylon)?Component Specification Sheet Set Up(Phylon) (此部分无中文) ?Phylon Midsole Specifications PH全插规格 ?Phylon Preform Specifications PH粗胚规格 ?Preform Drawing 粗胚图 ?Component Specification Sheet Set Up(PU) (此部分无中文) ?PU Midsole Specifications PU全插规格 ?PU Midsole Specifications II PU数据表 ?Components Specification Sheet(PU) 部件明细单(PU) ?PU Midsole Pouring Specification PU灌注明细 ?Outsole Color Schedule 本底颜色明细 ?Outsole Preform Specifications 本底粗胚规格 ?Outsole Pressing Process 本底压制流程 ?Outsole Degreasing Process 本底水洗流程 ********************************************************************* ΦPU Section ΦPU部分 ********************************************************************* air bag schedule 空气袋分段 specific instructions 特别说明 air bag diagram 空气袋图示 hardness(skin on) 硬度(带皮) density 密度 elongation 延伸率 tear 撕力 tensile 拉力 split tear 撕裂 painting 喷漆 MCS number 材料编号 mold release agent 脱模剂 polyurethane 聚安脂 polyester 聚脂 Density must be within NIKE spec and follow weight chart 密度必须符合NIKE要求及重量表 No dirty midsole sidewalls yellowing or poor cosmetics due to mold condition. 无因模具造成的边墙黄变及外观不良。 Correct molded or painted colors per NIKE confirmation. 根据NIKE的确认,成型材料及喷漆颜色正确。 Correct top/bottom edge trimming within 1mm width allowance. 正确修边上部及底部边缘,允许1mm余量。 No larger than 5mm diameter internal air voids.(checked by light table)
术语表 Acceptance Criteria–接受标准:接受测试结果的数字限度、范围或其他合适的量度标准。Active Pharmaceutical Ingredient(API)(or Drug Substance)-活性要用成分(原料药)旨在用于药品制造中的任何一种物质或物质的混合物,而且在用于制药时,成为药品的一种活性成分。此种物质在疾病的诊断,治疗,症状缓解,处理或疾病的预防中有药理活性或其他直接作用,或者能影响机体的功能和结构。 API Starting Material–原料药的起始物料:用在原料药生产中的,以主要结构单元被并入该原料药的原料、中间体或原料药。原料药的起始物料可能是在市场上有售,能够根据合同或商业协议从一个或多个供应商处购得,或者自己生产。原料药的起始物料通常有特定的化学特性和结构。 Batch(or Lot)-批:有一个或一系列工艺过程生产的一定数量的物料,因此在规定的限度内是均一的。在连续生产中,一批可能对应与生产的某以特定部分。其批量可规定为一个固定数量,或在固定时间间隔内生产的数量。 Batch Number(or Lot Number)-批号用于标识一批的一个数字、字母和/或符号的唯一组合,从中可确定生产和销售的历史。 Bioburden–生物负载:可能存在与原料、原料药的起始物料、中间体或原料药中的微生物的水平和种类(例如,治病的或不治病的)。生物负载不应当当作污染,除非含量超标,或者测得治病生物。 Calibration–校验:证明某个仪器或装置在一适当的量程范围内测得的结果与一参照物,或可追溯的标准相比在规定限度内。 Computer System–计算机系统:设计安装用于执行某一项或一组功能的一组硬件元件和关联的软件。 Computerized System–计算机化系统与计算机系统整合的一个工艺或操作。Contamination–污染:在生产、取样、包装或重新包装、贮存或运输过程中,具化学或微生物性质的杂质或外来物质进入或沾染原料、中间体或原料药。 Contract Manufacturer–协议制造商:代表原制造商进行部分制造的制造商。 Critical–决定性的:用来描述为了确保原料药符合规格标准,必须控制在预定范围内的工艺步骤、工艺条件、测试要求或其他有关参数或项目。 Cross-Contamination–交叉污染:一种物料或产品对另一种物料或产品的污染。 Deviation–偏差:对批准的指令或规定的标准的偏离。 Drug(Medicinal)Product–药品:经最后包装准备销售的制剂(参见Q1A) Drug Substance–药物见原料药 Expiry Date(or Expiration Date)-有效期:原料药容器/标签上注明的日期,在此规定时间内,该原料药在规定条件下贮存时,仍符合规格标准,超过这以期限则不应当使用。 Impurity–杂质:存在与中间体或原料药中,任何不希望得到的成分。 Impurity Profile–杂质概况:对存在于一种原料药中的已知和未知杂质的描述。 In-Process Control(or Process Control)-中间控制:生产过程中为监测,在必要时调节工艺和/或保证中间体或原料药符合其规格而进行的检查。 Intermediate–中间体:原料药工艺步骤中生产的、必须经过进一步分子变化或精制才能成为原料药的一种物料。中间体可以分离或不分离。 Manufacture–制造:物料的接收、原料药的生产、包装、重新包装、贴签、重新贴签、质量控制、放行、贮存和分发以及相关控制的所有操作。 Material–物料:原料(起始物料,试剂,溶剂),工艺辅助用品,中间体,原料药和包装及贴签材料的统称。
建筑术语中英文对照 建筑 build; architecture; construct; architectural; architectural & industrial ceramics 建筑安装工程量 construction work quantity 建筑板材 building board 建筑材料表 list of building materials 建筑材料检验 building material testing 建筑材料行 building material dealer 建筑材料运输列车 construction train 建筑草图 architectural sketch 建筑朝向 building orientation 建筑成本预算 construction cost estimate 建筑承包商 building contractor 建筑尺度 architectural scale 建筑处理 architectural treatment 建筑创作 architectural creation 建筑大五金 architectural metalwork 建筑大样 architectural detail 建筑单元 building unit 建筑费 construction cost 建筑风格 architectural style 建筑辅助系统 building subsystem 建筑钢 construction(al) steel 建筑钢板 building sheet 建筑高度 building height; height of building 建筑高度分区 building height zoning; height zoning 建筑工程升降机 builder's lift 建筑工地选择 siting
高分子专业术语中英文对照表
加工processing 反应性加工reactive processing 等离子体加工plasma processing 加工性processability 熔体流动指数melt [flow] index 门尼粘度Mooney index 塑化plasticizing 增塑作用plasticization 内增塑作用internal plasticization 外增塑作用external plasticization 增塑溶胶plastisol 增强reinforcing 增容作用compatibilization 相容性compatibility 相溶性intermiscibility 生物相容性biocompatibility 血液相容性blood compatibility 组织相容性tissue compatibility 混炼milling, mixing 素炼mastication 塑炼plastication 过炼dead milled 橡胶配合rubber compounding 共混blend 捏和kneading 冷轧cold rolling 压延性calenderability 压延calendering 埋置embedding 压片preforming 模塑molding 模压成型compression molding 压缩成型compression forming 冲压模塑impact moulding, shock moulding 叠模压塑stack moulding 复合成型composite molding 注射成型injection molding 注塑压缩成型injection compression molding 射流注塑jet molding 无流道冷料注塑runnerless injection molding 共注塑coinjection molding 气辅注塑gas aided injection molding 注塑焊接injection welding 传递成型transfer molding
CDB工程专业术语中英文对照(二) 添加时间:2013-4-24 节流截止放空阀 2011-08-10 16:50:46| 分类:English | 标签:|字号大中小订阅 六、仪表及自动控制 通用描述 COMMON DESCRIPTION 设备名称Equipment Name 缩写 ABB. 分散控制系统Distributed Control System DCS 安全仪表系统Safety Instrumentation System SIS 紧急切断系统Emergency Shutdown system ESD 火气系统Fire and Gas system F&G 监视控制和数据采集系统 Supervisory Control and Data Acquisition SCADA 可编程逻辑控制器Programmed Logic Controller PLC 远程终端单元Remote Terminal Unit RTU 站控系统Station Control System SCS 中央控制室Central Control Room CCR 操作间Operation room 机柜间Equipment room/ Cabinet room 大屏显示系统Large Screen Display system LSD 流量类仪表 FLOW INSTRUMENT 设备名称Equipment Name 孔板Orifice Plate 文丘里流量计Venturi Flowmeter 均速管流量计Averaging Pitot Tube 阀式孔板节流装置 Orifice Plate in quick change fitting 涡轮流量计Turbine Flowmeter
五金模具常用专业术语中英文对照表 上模座upper die set成型公form punch 脱料板stripper 垫板subplate/backup plate 下模座die plate滑块CAM slider 垫脚parallel 误检misfeeder 托板mounting plate顶料销kick off 初始管位first start pin带肩螺丝shoulder screw 两用销lifter pin氮气汽缸gas spring 弹簧护套spring cage 拔牙螺丝jack screw 侧冲组件cam section 导正装置guide equipment 漏废料孔slug hole刀口trim line 加强装置enhance equipment 入子insert 护套bushing 整形公restrike forming punch 止挡板stop plate 挂台head 扣位pocket of head 导柱guide post 导套guide bushing 油嘴oil nipple 接刀口mismatch/cookie bites 限位块stop block 挡块stopper 浮块lifter 压块keeper 靠块heel 对正块alignment block 简易模prototype tooling 检具gage/checking fixture 料带图strip layout 闭合高度shut hight 俯视图top view 料带strip 公差tolerance 正视图front view 走位travel 避位/空pocket 退磁demagnetization 间隙clearance 真空热外理vacuum heat treatment 镗孔mill hole 表面外理surface coasting 镀钛TD coasting 沉头counter sink 精锣finish mill 线割wire cutting 穿丝孔first wire hole 斜度taper 镭射laser-cut 上夹板/固定座holder/retainer 下模座lower die set 成刑母公forming die
专业术语常用名词缩写中英文对照表 来源:河北电视台网站时间:2007年8月27日点击:13 专业术语常用名词缩写中英文对照(A-L) A:Actuator 执行器 A:Amplifier 放大器 A:Attendance员工考勤 A:Attenuation衰减 AA:Antenna amplifier 开线放大器 AA:Architectural Acoustics建筑声学 AC:Analogue Controller 模拟控制器 ACD:Automatic Call Distribution 自动分配话务 ACS:Access Control System出入控制系统 AD:Addressable Detector地址探测器 ADM:Add/Drop Multiplexer分插复用器 ADPCM:Adaptive Differential ulse Code Modulation 自适应差分脉冲编码调制AF:Acoustic Feedback 声反馈 AFR:Amplitude /Frequency Response 幅频响应 AGC:Automati Gain Control自动增益控制 AHU:Air Handling Unit 空气处理机组 A-I:Auto-iris自动光圈 AIS:Alarm Indication Signal 告警指示信号 AITS:Acknowledged Information Transfer Service确认操作 ALC:Automati Level Control 自动平衡控制 ALS:Alarm Seconds 告警秒 ALU:Analogue Lines Unit 模拟用户线单元 AM:Administration Module管理模块 AN:Access Network 接入网 ANSI:American National Standards Institute美国国家标准学会 APS:Automatic Protection Switching 自动保护倒换 ASC:Automati Slope Control 自动斜率控制 ATH:Analogue Trunk Unit 模拟中继单元 ATM:Asynchrous Transfer Mode 异步传送方式 AU- PPJE:AU Pointer Positive Justification 管理单元正指针调整 AU:Administration Unit 管理单元 AU-AIS:Administrative Unit Alarm Indication SignalAU告警指示信号AUG:Administration Unit Group 管理单元组 AU-LOP:Loss of Administrative Unit Pointer AU指针丢失 AU-NPJE:AU Pointer Negative Justification管理单元负指针调整 AUP:Administration Unit Pointer管理单元指针 AVCD:Auchio &Video Control Device 音像控制装置 AWG:American Wire Gauge美国线缆规格 BA:Bridge Amplifier桥接放大器
一.电气名词 Electric items 二.线路(母线、回路)Lines (Bus , circuits) 三.设备 Equipments 四.保护、继电器 Protection , relays 五.电气仪表 Electric instruments 六.防雷 Lightning protection 七.接地 Grounding , earthing 八.室、所 Room , Substation 九.电修车间设备 Equipments of electric repair 十.材料 Material 十一.图名 Drawings , diagrams 十二.表头 Tables 十三.标准图词汇 Terms from standard DWG 一.电气名词 Electric items 交(直)流 Alternating (direct) current 短路电流 Short-circuit current 起始次暂态短路电流 Initial subtransient short-circuit current 冲击电流 Impulse current 稳态短路电流 Steady state short-circuit current 临界电流 Critical current 切断电流 Rupturing current 熔断电流 Blow-out current 故障电流 Fault current 计算电流 Calculating current 极限有限电流 Limit effective current 过电流 Over current 逆电流 Inverse current 整定电流 Setting current 额定电流 Rated current 电流密度 Current density 短路电流最大有效值 Maximum effective value of short-circuit current 高压 High-voltage , High-tension 低压 Low-voltage , Low-tension 计算电压 Calculating voltage 激磁电压 Exciting voltage 冲击电压 Impulse voltage 临界电压 Critical voltage 残留电压 Residual voltage 击穿电压 Puncture voltage 脉动电压 Pulsating voltage 供电电压 Supply voltage 电力电压 Power voltage