文档库 最新最全的文档下载
当前位置:文档库 › CCNA考试实验命令总结

CCNA考试实验命令总结

CCNA考试实验命令总结

路由器实验:


router> enable 从用户模式进入特权模式

router# disable or exit 从特权模式退出到用户模式

router# show sessions 查看本机上的TELNET会话

router# disconnect 关闭所有的TELNET会话

router# show users 查看本机上的用户

router# erase startup-config 删除NVRAM中的配置

router# reload 重启路由器

router# config terminal 从用户模式进入特权模式

router(config)# hostname rl 配置用户名为rl

router(config)# #banner welcome# 配置开机话语

router# show controllers serial0 查看串口0的物理层信息 主要是查看DTE/DCE

router# show ip interface 查看端口的IP配置信息

router# show hosts 查看主机表

end or ctrl+z 从各种配置模式退到特权模式

rl(config)# no ip domain-lookup 关闭动态域名解析

rl(config)# ip domain-lookup 打开动态域名解析

rl(config)# ip name-server 202.106.0.20 打开动态域名解析之后便可以 指定DNS服务

rl(config)# interface serial 0 进入serial 0的接口配置模式

rl(config-if)# no shutdown 路由器出厂默认所有端口关闭 使用此命令使它们打开

rl(config-if)# encapsulation ppp 封装ppp

rl(config-if)# clockrate 64000 如果是DCE使需要设置时钟速率 如果是DTE使不必设置

rl(config-if)# bandwidth 64 设置端口带宽为64K

rl(config-if)# ctrl+c 或者ctrl+z 快捷键退出到特权模式

rl# show interface serial 0 查看s0信息,如果看到serial和 line protocol都显示up 说明链路两端都设置成功
注意:如果出现serial down, line down 可能对方的端口没有打no shutdown或者电缆没有插好;如果出现serial up, line down 可能是DCE端没有设置clock rate, 也可能是封装格式不对

rl# show cdp neighbors 查看CDP邻居信息 rl# show cdp entry *

rl(config-if)# ip add 10.0.0.1 255.0.0.0 进入相应的接口,配置相应的IP地址

rl# ping 10.0.0.2 使用ping命令查看邻居的连通性

rl# show ip route 查看路由表,可以看到以C打头的路由 信息,这是直连的路由信息;可以看到 R开头的路由信息,是从rip学来的路由 信息;可看到以I开头的路由信息取代 了以R开头的路由信息,这是因为igrp 的管理距离是100,小于rip的120

rl(config-if)# router rip 启动RIP路由协议

rl(config-router)# network 10.0.0.0 发布网段 注意network后面是接的网络号而不是IP地址 rl# show ip protocol 查看配置的路由协议

rl(config)# router igrp 300 一定要注意在IGRP后面加自治系统号 考试的时候题目会告诉你AS NUMBER, 照敲就是

rl(config-router)# network 10.0.0.0

rl(config)# line vty0 4 进入虚拟线程配置模式,在这个模式里可对 telnet功能进行配置

rl(config-line)# login

rl(config-line)# password cisco 配置telnet密码,默认的网络设备 telnet的 功能是关闭

的,配了密码之后会自动打开

rl(config)# enable password cisco 配置进入enable模式的密码, 区分大小写

rl(config)# enable secret ciscocisco 配置进入enable模式的密码,是加密的密码 show run是看不见的

rl(config)# line console 0

rl(config-line)# login

rl(config-line)# password cisco 配置进入用户模式的密码

rl(config-line)# logging synchronous 输入同步

rl(config-line)# exec-timeout 0 0 禁止因为一段时间没有输入而跳出

rl# copy running-config startup-config 保存配置, 考试的时候注意题目的要求,如果 题目里要求你保存配置就一定不能少了这一项

r1# copy tftp startup-config

r1# copy running-config tftp

r1# copy tftp flash

交换机实验:

switch(config)# ip address 192.168.0.177 255.255.255.0 与路由器在接口上的配置IP不同,交换机是在全局配置模式配置

switch(config)# ip default-gateway 192.158.0.1 给交换机配置一个缺省网关,请注意,不用写掩码

switch(config)# vlan2 name cisco 配置一个vlan2并且指定名字叫CISCO

switch# show interfaces 查看端口状态

switch(config)# interface e0/10 进入端口e0/10

switch(config-if)# vlan-membership static 2 将端口放进vlan2里面

switch(config)# int f0/26 进入快速以太网端口f0/26

switch(config-if)# trunk on 启用trunk,注意:只能在百兆以上端口 启用trunk

switch(config-if)# notrunk-vlan 51 52 在主干上关闭VLAN51、52的传输

相关文档