文档库

最新最全的文档下载
当前位置:文档库 > N1000-96-1122中文资料

N1000-96-1122中文资料

N1000-96-1122中文资料

N1000-96-1122中文资料

[ 2 YEAR WARRANTY ]? Active harmonic correction to EN61000-3-2

? 90VAC to 264VAC universal input

? Flexible output voltage configuration

? Two output power ratings

? Forced current sharing, all outputs

? DC OK(including LED)

? UL, CSA and TüV safety approvals

? Industry standard 5 x 8 x 11 inch footprint

The N1000 and N1200 series are a range of systems-orientated, one to four output power supplies which provide 1000W or 1200W of continuous power at line voltages from 90VAC to 264VAC. Both series are harmonically corrected and carry world wide safety approvals. Fully enclosed, fan cooled and in the industry standard 5 x 8 x 11 inch form, the N series is an ideal choice when the economy and predictable performance of a centralized system power supply are desired. A unique dual converter architecture isolates the 5VDC logic output and the peripheral voltages. Maximum flexibility is provided as power budgets shift and change during the design cycle or as system upgrades are implemented. This overcomes a major shortfall of many system power supplies which use a single converter. T o meet redundancy requirements, each output rail is isolated, individually regulated and features forced current share. System interface signals include AC and DC Good, current monitor (V1), overvoltage, OCP, over-temperature protection, remote enable, margin check and inhibit as standard. By combining robust performance and broad range, the N Series sets the standard for centralized system power supplies.

SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated

N1000-96-1122中文资料

N1000-96-1122中文资料

N1000-96-1122中文资料

N1000-96-1122中文资料

International Safety Standard Approvals

VDE0805/EN60950/IEC950 File No. R917062Certificate No. R9172062

UL1950 File No. E135734

CSA C22.2 No. 950 Bulletin No. 1402C

TüV

N1000-96-1122中文资料

Mechanical notes

A AC connector is 3 position terminal block (#8 screws included), mating to

#8 ring tongue terminal.

N1000-96-1122中文资料

B D

C output is 5/16-18 studs mating to 5/16 terminal lugs.

C J1 signal connector is Molex 39-30-1140 or equivalent. Mating connector

is Molex 39-01-2140 or equivalent.

D J2 signal connector is Molex 39-01-1120 or equivalent. Mating connector

is 39-01-2120 or equivalent.

E Signal connector contacts are Molex 39-00-0039 or equivalent.

F Auxiliary DC output(s) are 6 position terminal block (#8 screws included)

mating to #8 ring tongue terminal.

G TB1 and J2 are not installed on single output models.

N1000-96-1122中文资料

N1000-96-1122中文资料

ALL DIMENSIONS IN INCHES (mm)

Notes

11000W or 1200W max. power. 500/600W max. power (V2 thru V4). All outputs isolated.

2

Specifications refer to all outputs except as noted (V1).3Signal referenced to V1 output neg. sense trim.4Use 20AWG or larger twisted pair.

5Reference to Logic Ground (Pin J1-11).6See Figure 4.7See Figure 3.8

See Figure 5.

N1000-96-1122中文资料

Output Voltage

FIG. 4

N1000-96-1122中文资料

N1000-96-1122中文资料

FIG. 2 (Ref. FIG 5)

FIG. 1

Open = Nominal Voltage Tie to +5V for High Margin

N1000-96-1122中文资料

FIG. 3

N1000-96-1122中文资料

N1000-96-1122中文资料

N1000-96-1122中文资料

AC Power Fail Signal/DC OK Timing

AC Input Voltage

85Vrms

AC Good Flag

DC Outputs

DC Good Flag

FIG. 5

DS_N1000/N1200_19980401.PDF