EPS1D-F19-AE0009中文资料

*RoHS Directive 2002/95/EC Jan 27 2003 including Annex

Specifications are subject to change without notice.

Customers should verify actual device performance in their specific applications.

Closed Circuit Resistance ..............................................................................................................................................................................5 ohms maximum Open Circuit Resistance ..........................................................................................................................................................................500 K ohms minimum Contact Rating ....................................................................................................................................................10 milliamp @ 10 VDC or 0.1 watt maximum Insulation Resistance (500 VDC)......................................................................................................................................................1,000 megohms minimum Dielectric Withstanding Voltage (MIL-STD-202 Method 301)

Sea Level................................................................................................................................................................................................1,000 VAC minimum Electrical Travel ........................................................................................................................................................................................................Continuous Contact Bounce (15 RPM)..................................................................................................................................................................5 milliseconds maximum RPM (Operating)..................................................................................................................................................................................................120 maximum Encoder Switching Configuration (applies to detented version only)................................................................................................................Normally Open Phase Tolerance (CH A to CH B)..............................................................................................................................................................................90 ° ± 72 °

Environmental Characteristics

Operating Temperature Range ..........................................................................................................................................+1 oC to +85 oC (+34 °F to +185 °F)Storage Temperature Range ............................................................................................................................................-40 oC to +85 oC (-40 °F to +185 °F)https://www.wendangku.net/doc/7415086624.html,-STD-202, Method 103B, Condition B Vibration ..............................................................................................................................................................................................................................15 G Contact Bounce ............................................................................................................................................................................0.1 millisecond maximum Shock ..................................................................................................................................................................................................................................50 G Contact Bounce ............................................................................................................................................................................0.1 millisecond maximum Rotational Life ....................................................................................................................................................................................200,000 shaft revolutions Switch Life ..........................................................................................................................................................................................................100,000 cycles IP Rating..............................................................................................................................................................................................................................IP 40

Mechanical Characteristics

Mechanical Angle............................................................................................................................................................................................360 ° Continuous Running Torque..................................................................................................................................................................0.5 to 1.5 N-cm (0.75 to 2.25 oz-in.)Mounting Torque ..............................................................................................................................................................56 to 79 N-cm (5-7 lb.-in.) maximum Shaft Side Load (Static)....................................................................................................................................................................4.53 kg (10 lbs.) minimum Weight ....................................................................................................................................................................................Approximately 21 gms. (0.75 oz.)Terminals ....................................................................................................................................................................................Printed circuit board terminals Soldering Condition ....................................................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.

Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.

Part can be wave soldered at 260 °C (500 °F) for 5 seconds, no wash process with no clean flux.

Marking ................................................................................................................................................Manufacturer’s name and part number, and date code Hardware ......................................................One lockwasher and one mounting nut supplied with each encoder, except where noted in the part number.

Switch Characteristics

Switch Type ..................................................................................................................................................................................Push Momentary, SPST N.O.Power Rating (Resistive Load)........................................................................................................................................................10 milliamps @ 12 volts DC Closed Switch Resistance..............................................................................................................................Less than 200 ohms @ 440 gram force on shaft Switch Travel ......................................................................................................................................................................................................2.25 ±0.25 mm Switch Actuation Force..................................................................................................................................................................370 ±70 grams (5 ±1 oz.-in.)

Quadrature Output Table - This table is intended to show available outputs as currently defined.

FULL CYCLE PER DETENT

(Normally Open in Detent Shown)

(

y p

)

Open Circuit CW

Channel A

D

D

D

D

D

Closed Circuit Open Circuit

Closed Circuit Channel B

RECOMMENDED INCREMENTAL CONTROL DIAGRAM FOR USE WITH A DEBOUNCE CIRCUIT

*R

o H S C O M P L I A N T V E R S I O N S A V A I L A B L E

Specifications are subject to change without notice.

Customers should verify actual device performance in their specific applications.

EPS - Digital Contacting Encoder With Momentary Switch Option

SNAP-IN MOUNTING - S style bushing / F style shaft

Product Dimensions

PCB MOUNTING DIMENSIONS

1.10(.043)

MM (IN)

DIMENSIONS:

12345

TERMINAL PIN NO.

CHANNEL B COMMON CHANNEL A TOLERANCES: EXCEPT WHERE NOTED .51 .13DECIMALS: .XX ± (.020) .XXX ±

(.005)

EPS - Digital Contacting Encoder With Momentary Switch Option

How to Order

PART NUMBERING SYSTEM

REV. 10/08

Specifications are subject to change without notice.

Customers should verify actual device performance in their specific applications.