CRYSTAL OSCILLATORS
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Data Sheet 0635J
OE-X8HXXXXX
Precision SC-cut OCXO in 36x27mm “Europack”
CRYSTAL OSCILLATORS
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Data Sheet 0635J
OE-X8HXXXXX Series
Parameter Symb Condition Min Typ Max Unit Note Absolute Maximum Ratings
Input Break
Down Voltage
Vcc -0.5 13.0 V Storage temper. Ts -40 85 °C Control Voltage
Vc -1 9 V Electrical
Frequency
F 4.8 10.000 160 MHz 1* vs. Temp. ±10 ppb See chart below Frequency stability ?F/F
vs. Supply 1 2 ppb/V Aging
per day per year 5E-10 1E-7 after 30 days 5E-8 available2*Allan Variance
.1s to 10s 1E-11 SSB Phase Noise
1Hz 10 Hz 100 Hz 1 KHz 10 KHz -90 -120 -150 -153 -160 dBc/Hz 3* Retrace
After 30 minutes ±10 ppb G-sensitivity
worst direction ±1.0 ppb/G
A l l p a r a m e t e r s f o r 10 M H z
Input Voltage
Vcc 4.75 3.15 11.4 5.0 3.3 12.0 5.25 3.45 12.6
V See chart below to specify Power consumption
P steady state, 25°C steady state, -30°C start-up @ -30°C 0.8 1.5 2.5 1.2 3.2 W Standard Operating Temperature, for Op Temp. 85 °C ad 20% Spectral Purity
Subharmonics Spurious Harmonics/Sine -50 -35 -45 -80 -30
dBc At Higher Frequencies Load
10KOhm//15pF (HCMOS/TTL), 50 Ohm (Sinewave) Warm-up time τ to 0.1ppm accuracy 3 5 minutes 3 min. at 12V Output Waveform
3.3V HCMOS/TTL compatible or Sinewave (+7± 3) dBm -25dBm Harmonics at sine Control voltage
Vc 0 4.0 V Pull range
from nominal F ±0.5 ±1 ppm Deviation slope
Monotonic, posit 0.4 ppm/V Setability
Vc0 @25°C, Fnom. 1.0 2.0 3.0 V Environmental and Mechanical
Operating temp. range
-30°C to 70°C Standard, Other options – see chart below Mechanical Shock
Per MIL-STD-202, 30G, 11ms Vibration
Per MIL-STD-202, 5G to 2000 Hz Soldering Conditions
260°C for 10s Max leads only Electrical Connections
Pin Out
Pin #1-Vc ; Pin#2 – Vref; Pin #3 – Vcc; Pin #4- Output ; Pin #5- GND;
Notes: 1* Higher frequencies can be achieved either by using higher frequency crystals or by low noise analog harmonic multiplication. Both methods have advantages and drawbacks. If lowest possible phase noise on the noise floor is most important – high frequency crystal will be used. If
phase noise close to the carrier and aging are more important – multiplication will be used. Please consult factory for your specific requirement. 2* Aging rate is usually proportional to the operating frequency, unless higher frequency is achieved by multiplication. Keep it in mind
while specifying aging. 3* Phase noise deteriorates with frequencies going higher. If analog multiplication is used to achieve higher frequency the phase noise roughly follows the formula of additional 20LogN, where N is a multiplication factor across entire frequency offset range. If higher frequency is
achieved by using higher frequency crystal phase noise close to the carrier deteriorates due to the lower Q of the crystal and is usually worse, compared to multiplied solution. On the noise floor, however it remains more or less the same. This design usually starts utilizing multiplication techniques in the range of 25 MHz to 35 MHz.
CRYSTAL OSCILLATORS
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Data Sheet 0635J
OE-X8HXXXXX Series
Creating a Part Number