当前位置：文档库 › SPS-9140BMWG中文资料

SPS-9140BMWG中文资料

Optoway SPS-9140MWG

***********************************************************************************************************************************************************************

**********************************************************************************************************************************************************************

OPTOWAY TECHNOLOGY INC. No .38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303

Tel: 886-3-5979798 Fax: 886-3-5979737

12/1/2005 V2.0 1

SPS-9140MWG / SPS-9140BMWG (RoHS Compliant)

3.3V / 1310 nm / Multirate Digital Diagnostic SFP LC SINGLE-MODE TRANSCEIVER **********************************************************************************************************************************************************************

FEATURES

l Hot-Pluggable SFP Footprint LC Optical Transceiver l Small Form-Factor Pluggable (SFP) MSA compatible l Compliant with SONET OC-48 (LR-1) / SDH STM-16 (L-16.1)

l Compliant with Fibre Channel 1x/2x SM-LC-L FC-PI l Compliant with IEEE 802.3z 1000BASE l SFF-8472 Digital Diagnostic Function l 1310 nm DFB LD Transmitter l APD High Sensitivity Receiver l 26 dB Power Budget at Least

l AC/AC Coupling according to MSA l Single +3.3 V Power Supply l RoHS Compliant

l 0 to 70o C Operation : SPS-9140MWG l -10 to 85o C Operation : SPS-9140BMWG

l Class 1 Laser International Safety Standard IEC-60825 Compliant

APPLICATIONS

l SONET OC-48 / SDH STM-16 l SONET OC-12 / SDH STM-4 l SONET OC-3 / SDH STM-1

l Gigabit Ethernet / 1X/2X Fibre Channel

DESCRIPTION

The SPS-9140MWG series single mode transceivers is small form factor pluggable module for bi-directional serial optical data communications such as SONET OC-48 / SDH STM-16, Gigabit Ethernet 1000BASE and Fibre Channel 1x/2x SM-LC-L FC-PI. It is with the SFP 20-pin connector to allow hot plug capability. Digital diagnostic functions are available via an I 2C. This module is designed for single mode fiber and operates at a nominal wavelength of 1310 nm. A guaranteed minimum optical link budget of 26 dB is offered which can correspond to a link distance of over 40 km (assuming worst case fiber loss of 0.45 dB/km). The transmitter section uses a multiple quantum well 1310 nm DFB laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC.

LASER SAFETY

This single mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug.

ORDER INFORMATION

P/No. Bit Rate

(Mb/s)

SONET /SDH

Distance (km) Wavelength (nm) Package

Temp. (o C) TX Power (dBm) RX Sens. (dBm) RoHS Compliant SPS-9140MWG

Multirate* LR-1/L-16.1

40 1310 DFB LC SFP with DMI 0 to 70 3 to -2 -28 Yes SPS-9140BMWG Multirate* LR-1/L-16.1

1310 DFB LC SFP with DMI

-10 to 85

3 to -2

-28

Yes

Multirate*: 2.67 Gb/s / OC-48 / 2X FC / GbE / 1X FC / OC-12 / OC-3

Absolute Maximum Ratings

Parameter

Symbol Min Max Units Notes

Storage Temperature

Tstg -40 85 o C

Operating Case Temperature Topr 0 -10 70 85 o C SPS-9140MWG SPS-9140BMWG Power Supply Voltage

Vcc

-0.5

3.6

Recommended Operating Conditions

Parameter

Symbol Min Typ Max Units / Notes

Power Supply Voltage

Vcc 3.1 3.3 3.5 V

Operating Case Temperature Topr 0 -10 70 85 o

C / SPS-9140MWG o

C / SPS-9140BMWG

Power Supply Current I CC (TX+RX)

230 300 mA Data Rate

125

2488

2670

Mb/s

Transmitter Specifications (0o C < Topr < 70o C, 3.1V < Vcc < 3.5V)

Parameter Symbol Min Typ Max Units Notes

Optical

Optical Transmit Power Po -2 --- 3 dBm 1

Output Center Wavelength λ1280 1310 1335 nm

Output Spectrum Width ?λ--- --- 1 nm -20 dB Width

Side Mode Suppression Ratio SMSR 30 dB

Extinction Ratio E R8.2 --- --- dB

Output Eye Compliant with Telecordia GR-253-GORE and ITU-T Recommendation G.957

Optical Rise Time t r150 ps 20 % to 80% Values Optical Fall Time t f150 ps 20 % to 80% Values Relative Intensity Noise RIN -120 dB/Hz

Electrical

Data Input Current – Low I IL-350 μA

Data Input Current – High I IH350 μA

Differential Input Voltage V IH - V IL0.5 2.4 V Peak-to-Peak

TX Disable Input Voltage – Low T DIS, L0 0.5 V 2

TX Disable Input Voltage – High T DIS, H 2.0 Vcc V 2

TX Disable Assert Time T ASSERT10 μs

TX Disable Deassert Time T DEASSERT 1 ms

TX Fault Output Voltage -- Low T FaultL0 0.5 V 3

TX Fault Output Voltage -- High T FaultH 2.0 Vcc+0.3 V 3

1. Output power is power coupled into a 9/125 μm single mode fiber.

2. There is an internal 4.7K to 10K ohm pull-up resistor to VccTX.

3. Open collector compatible,

4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage).

Receiver Specifications(0o C < Topr < 70o C, 3.1V < Vcc < 3.5V)

Parameter Symbol Min Typ Max Units Notes

Optical

Sensitivity @ OC-48Sens1 -9 -28 dBm 4 Sensitivity @2X Fibre Channal Sens2 -9 -28 dBm 5 Sensitivity @Gigabit Ethernet Sens3 -9 -30 dBm 5 Sensitivity @OC-12 Sens4 -9 -29 dBm 4 Sensitivity @OC-3 Sens5 -18 -30 dBm 4

Signal Detect -- Asserted Pa --- -28 dBm Transition: low to high Signal Detect -- Deasserted Pd -40 --- --- dBm Transition: high to low Signal detect -- Hysteresis 1.0 --- dB

Optical Path Penalty 1 dB

Wavelength of Operation 1100 --- 1600 nm

Electrical

Differential Output Voltage V OH– V OL0.6 2.0 V

Output LOS Voltage -- Low V OL0 0.5 V 6

Output LOS Voltage -- High V OH 2.0 Vcc+0.3 V 6

4. Measured at 2-1 PRBS at BER 1E-10 @ 1300 nm.

5. Measured at 27-1 PRBS at BER 1E-12 @ 1300 nm.

6. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage).

*********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303

***********************************************************************************************************************************************************************

OPTOWAY TECHNOLOGY INC. No .38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303

Signal Name

Description

Signal Name Description

1 TX GND Transmitter Ground

11 RX GND Receiver Ground

2 TX Fault Transmitter Fault Indication

12 RX DATA OUT- Inverse Receiver Data Out 3 TX Disable Transmitter Disable (Module disables on high or open)

13 RX DATA OUT+ Receiver Data Out 4 MOD-DFE2 Modulation Definition 2 – Two wires serial ID Interface

14 RX GND Receiver Ground

5 MOD-DEF1 Modulation Definition 1 – Two wires serial ID Interface

15 Vcc RX Receiver Power – 3.3V ±5% 6 MOD-DEF0 Modulation Definition 0 – Ground in Module

16 Vcc TX Transmitter Power – 3.3V ±5% 7 N/C Not Connected 17 TX GND

Transmitter Ground 8 LOS Loss of Signal 18 TX DATA IN+ Transmitter Data In

9 RX GND Receiver Ground 19 TX DATA IN- Inverse Transmitter Data In 10

RX GND

Receiver Ground

TX GND

Transmitter Ground

Module Definition

MOD-DEF2 PIN 4 MOD-DEF1 PIN 5 MOD-DEF0 PIN 6 Interpretation by Host 4

SDA

SCL

LV-TTL Low

Serial module definition

protocol

Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 family of components.