GENERAL DATA
Life Expectancy
Minimum operations Mechanical 1 x 107
Electrical 1 x 105at 12 A 250 VAC Res.Operate Time (typical)7 ms at nominal coil voltage Release Time (typical)
3 ms at nominal coil voltage (with no coil suppression)
Dielectric Strength 5000 Vrms coil to contact
(at sea level for 1 min.)1000 Vrms between open contacts Insulation 1000 megohms min. at 20°C Resistance
500 VDC 50% RH Insulation
C250
(according to Overvoltage category: III DIN VDE 0110, Pollution degree: 3
IEC 60664-1)Nominal voltage: 250 VAC
Dropout
Greater than 10% of nominal coil voltage Ambient Temperature
At nominal coil voltage
Operating
-40°C (-40°F) to 85°C (185°F) standard -40°C (-40°F) to 105°C (221°F) sensitive Storage
-40°C (-40°F) to 105°C (221°F)Vibration 0.062" (1.5 mm) DA at 10–55 Hz Shock 10 g
Enclosure
P .B.T. polyester
Terminals
Tinned copper alloy, P.C.Max. Solder Temp.270°C (518°F)Max. Solder Time 5 seconds Max. Solvent Temp.80°C (176°F)Max. Immersion Time 30 Seconds Weight
14 grams
Packing unit in pcs
20 per plastic tube / 1000 per carton box
ZET TLER
electronics GmbH
Fax +49 89 800 97 200 https://www.wendangku.net/doc/814637653.html,
office@https://www.wendangku.net/doc/814637653.html, 0 97 800 89 +49 Tel. Germany
Puchheim, D-82178 Junkersstrasse 3, 2004-09-27
CONTACTS
Arrangement SPDT (1 Form C)
SPST (1 Form A, 1 Form B)Ratings
Resistive load:
Max. switched power:360 W or 3324 VA Max. switched current:12 A
Max. switched voltage:150 VDC* or 400 VAC
* Note: If switching voltage is greater than 30VDC,
special precautions must be taken.Please contact the factory.
Rated Load UL, CUR
12 A at 277 VAC resistive, 50k cycles (standard coils) [1]
12 A at 277 VAC resistive, 100k cycles (standard coils) [2] [3]
10 A at 250 VAC resistive, 100k cycles (sensitive coils) [1]
1/2
HP at 250 VAC (1 Form A) [1]1/3
HP at 125 VAC (1 Form A) [1]B300 Pilot Duty [2]R300 Pilot Duty [2]
VDE 12 A at 250 VAC resistive, [1] [2] and [3]Material Silver cadmium oxide [1] or silver tin oxide [2]or silver nickel [3]. Gold plating available Resistance
< 50 milliohms initially
POWER RELAY
FEATURES ?Dielectric strength 5000 Vrms ?Low cost
?Epoxy sealed version available ?12 Amp switching
?Isolation spacing greater than 10 mm
?
Reinforced insulation, EN 60730-1 (VDE 0631, part 1),EN 60335-1 (VDE 0700, part 1)?UL, CUR file E44211 ?VDE 40006031COIL
Power
At Pickup Voltage 196 mW, standard coil (typical)
141 mW, sensitive coil Max. Continuous 1.7 W at 20°C (68°F) ambient Dissipation Temperature Rise 26°C (47°F) standard coil (at nominal voltage)17°C (31°F) sensitive coil Max. Temperature
130°C (266°F)
NOTES
1.All values at 20°C (68°F).
2.Relay may pull in with less than “Must Operate” value.
3.Specifications subject to change without notice.
RELAY ORDERING DATA
COIL SPECIFICATIONS – 12 A RATING
ORDER NUMBER*
Nominal Coil
Must Operate
Max. Continuous
Coil Resistance 1 Form A 1 Form C VDC VDC VDC Ohm ± 10%
5
3.5
10.2
62 AZ761–1A–5D
AZ761–1C–5D 6 4.212.390AZ761–1A–6D AZ761–1C–6D 9 6.318.3200AZ761–1A–9D AZ761–1C–9D 128.424.7360 AZ761–1A–12D AZ761–1C–12D 1812.637.0810AZ761–1A–18D AZ761–1C–18D 2416.849.41,440 AZ761–1A–24D
AZ761–1C–24D 4833.698.05,760AZ761–1A–48D AZ761–1C–48D 6042.0112.97,500AZ761–1A–60D AZ761–1C–60D 11077.0206.925,200AZ761–1A–110D AZ761–1C–110D
COIL SPECIFICATIONS – SENSITIVE COIL - 10 A RATING ORDER NUMBER*
Nominal Coil
Must Operate
Max. Continuous
Coil Resistance 1 Form A 1 Form C VDC VDC VDC Ohm ± 10%
5
3.8
13.0
100
AZ761–1A–5DS AZ761–1C–5DS 6 4.515.6144AZ761–1A–6DS AZ761–1C–6DS 129.031.3576AZ761–1A–12DS AZ761–1C–12DS 1813.546.91,296AZ761–1A–18DS AZ761–1C–18DS 2418.062.62,304 AZ761–1A–24DS
AZ761–1C–24DS 4836.0
125.29,216AZ761–1A–48DS AZ761–1C–48DS 60
45.0
147.8
12,867
AZ761–1A–60DS
AZ761–1C–60DS
* “1A” or “1C” denote silver cadmium oxide contacts.Substitute “1B” in place of “1A” for 1 Form B contact.
Add suffix “E” to “1A” or “1B” or “1C” for silver tin oxide contacts. Add suffix “B” to “1A” or “1B” or “1C” for silver nickel contacts. Add suffix “E” at the end of order number for sealed version.
Add suffix “A” at the end of order number for gold plated contacts.
Add suffix “K” at the end of order number for 5 mm pin spacing version.
2004-09-27
ZET TLER
electronics GmbH
Fax +49 89 800 97 200 https://www.wendangku.net/doc/814637653.html,
office@https://www.wendangku.net/doc/814637653.html, 0 97 800 89 +49 Tel. Germany
Puchheim, D-82178 Junkersstrasse 3,