PhlatLight?
PT120
Projection Chipset
SUMMARY DATA SHEET
Technology Overview
Luminus Devices’ Projection Technology is an innovative solid-state light source created to replace arc lamps in projection systems. Enabled by unique use of Photonic Lattice technolo-gy, PhlatLight chipsets represent a major breakthrough in brightness that delivers all the benefits of solid state light sources in projections applications:
- Wide color gamut for vivid colors, exceeds NTSC.
-Instant turn-on, no more wait time.
- High Reliability; no lamp replacement
-Environmentally friendly technology - Mercury-free.
- Electronic control of color points and light intensity on
a frame by frame basis
PhlatLight products benefit from numerous innovations in the domain of packaging, thermal management and optical cou-pling that allow designers to achieve efficient light engine de-signs and deliver high screen brightness.
Features
?Matched RGB Chipset with 12mm2 emitting area designed for projection applications
?Photonic lattice technology for very high surface brightness ?100% surface emission for high collection efficiency and low optical losses
?Wide color gamut: RED 623 nm, GREEN 525 nm, BLUE 462 nm, EP Blue 460nm typical dominant wavelength ?Single emitting area per color allows for collection with sin-gle lens for simplified optics
?16:9 aspect ratio matched with micro-display and screen as-pect ratio
?Thermally efficient Type CX Common Anode package ?RoHS (lead-free) compliant
Applications
?Specifically engineered for Rear-Projection Displays, front projectors, head-up projection displays
?Optimized for Micro-Display diagonal sizes ranging from 0.65” to 0.95” with 16:9 aspect ratio.
?Suitable for DLP? (e.g. xHD5, 0.65”, 0.95” 1080p), LCoS, HTPS and 3LCD microdisplays
Optical and Electrical Characteristics
Symbol Red Green Blue EP-Blue1
Preliminary
Unit Bin Kit MPB MPB MPB EPA
Emitting Area11.9611.9611.9611.96mm2 Emitting Area Dimensions 4.6x2.6 4.6x2.6 4.6x2.6 4.6x2.6mm x mm Characteristics at recommended Pulsed Drive Current I F2,3
Reference Duty Cycle425502525% Recommended Peak Drive Current 5typ I F30303030A Peak Luminous Flux6typΦv18003500600750lm Peak Radiometric Power typΦr10.47.312.116.3W
Dominant Wavelength
λdmin619516455450nm typλd623525462460nm λdmax630535469468nm
FWHM - Spectral bandwidth at 50% of Φv typΔλd1*******nm Color Saturation7,8typ 1.000.790.990.99
Chromaticity Coordinates7,8typ x0.6970.1710.1440.154 typ y0.3030.7020.0400.024
Forward Voltage min V Fmin 2.2 3.5 3.5 3.2V typ V F 2.6 4.9 4.9 4.0V max V Fmax 3.4 5.9 5.9 5.2V
Dynamic Resistance typΩdyn0.020.030.020.02Ω Device Thermal Characteristics and Lifetime
Thermal Coefficient of Photometric Flux typ-1.1-0.2~0~0% / oC Thermal Coefficient of Radiometric Flux typ-0.7-0.2-0.2-0.2% / oC Forward Voltage Temperature Coefficient typ-3.0-3.0-3.0-3.0mV / oC Median Lifetime9>60,000>60,000>60,000>60,000Hours
Characteristics at Reference Continuous Drive Current I F (Continuous Waveform)2
Reference Drive Current typ I F 18181818A Luminous Flux typ Φv 10102450435540lm Radiometric Flux typ Φr 5.8 4.78.010.8W Dominant Wavelength typ λd
624528464462
nm
Color Saturation 7,8
typ 1.00
0.830.990.99FWHM - Spectral bandwidth at 50% of Φv typ Δλd 18382121nm
Chromaticity Coordinates
7,8
typ x 0.6980.1830.1410.153typ y 0.3010.7030.0440.025Forward Voltage min
V Fmin 2.0 3.1 3.1 2.8V typ V F 2.3 4.4 4.4 3.6V max
V Fmax 3.0 5.3 5.3 4.6V Dynamic Resistance
typ
Ωdyn
0.02
0.03
0.02
0.05
Ω
Note 1:EP-Blue is recommended for new designs. Please see page 9 for part ordering numbers.
Note 2:
All ratings are based on operation with a constant heat sink temperature T hs = 40oC. See Thermal Resistance section for T hs defini-tion.
Note 3:Parameters rated at typical duty cycle and Pulsed operation frequency f>240Hz;
Note 4:
Duty Cycle used to specify device ratings under Pulsed operation. PhlatLight devices can operate at duty cycles ranging from 1% to 100%. At higher duty cycles, drive current should be adjusted to maintain the junction temperature at desired levels to meet the application lifetime requirements.
Note 5:In pulsed operation, rise time from 10 to 90% of forward current should be larger than 0.5 microseconds.
Note 6:For Blue and EP-Blue devices, total flux from emitting area at typical dominant wavelength at recommended peak drive current con-ditions.
Note 7:In CIE 1931 chromaticity diagram coordinates, normalized to X+Y+Z=1Note 8:For Reference only
Note 9:
Assuming Tj<80oC for Red devices and Tj<115oC for Blue devices and Tj<125oC for Green devices
Optical and Electrical Characteristics
Symbol
Red
Green
Blue
EP-Blue 1
Preliminary
Unit
DC t T
--=T
Luminous Flux variation with Wavelength: Φv = f (λd ) at Recommended Operating Current I F
See note 1 on page 6.
Absolute Maximum Ratings
Symbol
Red
Green
Blue
EP-Blue
Unit
Maximum Current 1,2
Max 36
363636A Maximum Operating Junction Temperature 3Max
T jmax
110170170170oC Storage Temperature Range
-40/+100
-40/+100
-40/+100
-40/+100
oC
Note 1:
Luminus PhlatLight LEDs are designed for operation to an absolute maximum forward drive current density of 2.5A/mm 2 cw, and
3A/mm 2 pulsed (f>240Hz, duty cycle < 60%). Please refer to absolute maximum rating table above for specific absolute maximum cur-rents for the products covered in this datasheet. Product lifetime data is specified at recommended forward drive currents. Sus-tained operation at absolute maximum currents will result in a reduction of device lifetime compared to recommended forward drive currents. Actual device lifetimes will also depend on junction temperature. Refer to the lifetime derating curves (available from Luminus) for further information.
Note 2:In pulsed operation, rise time from 10 to 90% of forward current should be larger than 0.5 microseconds.
Note 3:Sustained operation at Maximum Operating Junction T emperature (T jmax ) will result in reduced device life time.
Luminous Flux variation with Drive Current - Φv = f (I F ) - Typical
See notes 1,2 on page 6.
Dominant Wavelength variation with Forward Current - λd = f(I F ) - Typical
See notes 1,2 on page 6.
Forward Voltage variation with Drive current - V F = f(I F ) - Typical
See notes 1,2 on page 6.
See note 3 on page 6.
Chart Notes
Note 1:For Pulsed operation, typical RGB duty cycles used are 25%, 50% and 25% respectively for pulsed operation (T hs =40o C). Note 2:Yellow square indicate device operating point under recommended conditions listed in the Optical and Electrical Char-acteristics table.
Note 3:Typical Spectrum at recommended peak drive current.
Thermal Resistance
Thermistor Information
The thermistor used in PhlatLight? devices mounted on core-boards is from Murata Manufacturing Co. The global part number is NCP15XH103J03RC. Please see https://www.wendangku.net/doc/866787279.html,/ or http://www.murata.co.jp for details on calculating thermistor tempera-
ture.
1
2
28.00±0.2542
10.1
2x
3.13.0
ALIGNMENT HOLES 5.50
2x 2.9±0.1FASTENER HOLES
4.63EMITTING AREA 11.00
2.60EMITTING AREA
6.35
18.00
A
A
26.75±0.50
5.61
A
SECTION A-A
"A""B""C"
DETAIL A
DIMENSIONS IN MILLIMETERS
DIMENSION NAME DESCRIPTION
NOMINAL DIMENSION
TOLERANCE
"A"
TOP OF METAL SUBSTRATE TO TOP OF GLASS 0.95
0.13"B"EMITTING AREA TO TOP OF GLASS
0.670.16"C"
TOP OF METAL SUBSTRATE TO EMITTING AREA
0.28
0.05
Recommended connector for Anode and Cathode: Panduit Disco Lok ? Series P/N: DNG14-250FL-C or equivalent Thermistor Connector: MOLEX P/N 53780-0270. Recommended Female: MOLEX P/N 51146-0200 or equivalent For detailed drawing of the PT120 Type CX package, please refer to the DWG-001124 document
Ordering Information
https://www.wendangku.net/doc/866787279.html,
The products, their specifications and other information appearing in this document are subject to change by Luminus Devices without notice. Luminus Devices assumes no liability for errors that may appear in this document, and no liability otherwise arising from the application or use of the product or information contained herein. None of the information provided herein should be considered to be a representation of the fitness or suitability of the product for any particular application or as any other form of warranty . Luminus Devices’ product warranties are limited to only such warranties as accompany a purchase contract or purchase order for such products. Nothing herein is to be construed as constituting an additional warranty . No infor-mation contained in this publication may be considered as a waiver by Luminus Devices of any intellectual property rights that Luminus Devices may have in such information. PhlatLight ?
is a registered trademark of Luminus Devices, Inc., all rights reserved.
This product is protected by U.S. Patents 6,831,302; 7,074,631; 7,083,993; 7,084,434; 7,098,589; 7,105,861; 7,138,666; 7,166,870; 7,166,871;7,170,100; 7,196,354; 7,211,831; 7,262,550; 7,274,043; 7,301,271; 7,341,880; 7,344,903; 7,345,416; 7,348,603; 7,388,233; 7,391,059 Patents Pending in the U.S. and other countries.
Device Part Number
Color Description
PT-120-R-C11-MPB Red Bin Kit MPB Red PhlatLight PT120 device consisting of a 12mm 2 LED, thermistor and con-nector mounted on a type CX copper-core PCB
PT-120-G-C11-MPB Green Bin Kit MPB Green PhlatLight PT120 device consisting of a 12mm 2 LED, thermistor and connector mounted on a type CX copper-core PCB
PT-120-B-C11-MPB 1Note 1:Not recommended for new designs
Blue
Bin Kit MPB Blue PhlatLight PT120 device consisting of a 12mm 2 LED, thermistor and connector mounted on a type CX copper-core PCB
PT-120-B-C11-EPA 2
Note 2:
Bin Kit EP A Blue is recommended for new designs.
EP-Blue
Bin Kit EPA Blue PhlatLight PT120 device consisting of a 12mm 2 LED, thermistor and connector mounted on a type CX copper-core PCB