文档库 最新最全的文档下载
当前位置:文档库 › Cisco交换机基本命令配置大全

Cisco交换机基本命令配置大全

1.switch(config)# hostname hostname

在基于CLI的交换机上设置主机名/系统名:

switch(enable) set system name name-string

2.在基于IOS的交换机上设置登录口令:

switch(config)# enable password level 1 password

在基于CLI的交换机上设置登录口令:

switch(enable) set password

switch(enable) set enalbepass

3.在基于IOS的交换机上设置远程访问:

switch(config)# interface vlan 1

switch(config-if)# ip address ip-address netmask

switch(config-if)# ip default-gateway ip-address

在基于CLI的交换机上设置远程访问:

switch(enable) set interface sc0 ip-address netmask broadcast-address

switch(enable) set interface sc0 vlan

switch(enable) set ip route default gateway

4.在基于IOS的交换机上启用和浏览CDP信息:

switch(config-if)# cdp enable

switch(config-if)# no cdp enable

为了查看Cisco邻接设备的CDP通告信息:

switch# show cdp interface [type modle/port]

switch# show cdp neighbors [type module/port] [detail]

在基于CLI的交换机上启用和浏览CDP信息:

switch(enable) set cdp {enable disable} module/port

为了查看Cisco邻接设备的CDP通告信息:

switch(enable) show cdp neighbors[module/port] [vlan duplex capabilities detail]

5.基于IOS的交换机的端口描述:

switch(config-if)# description description-string

基于CLI的交换机的端口描述:

switch(enable)set port name module/number description-string

6.在基于IOS的交换机上设置端口速度:

switch(config-if)# speed{10 100 auto}

在基于CLI的交换机上设置端口速度:

switch(enable) set port speed moudle/number {10 100 auto}
switch(enable) set port speed moudle/number {4 16 auto}

7.在基于IOS的交换机上设置以太网的链路模式:

switch(config-if)# duplex {auto full half}

在基于CLI的交换机上设置以太网的链路模式:

switch(enable) set port duplex module/number {full half}

8.在基于IOS的交换机上配置静态VLAN:

switch# vlan database

switch(vlan)# vlan vlan-num name vla

switch(vlan)# exit

switch# configure teriminal

switch(config)# interface interface module/number

switch(config-if)# switchport mode access

switch(config-if)# switchport access vlan vlan-num

switch(config-if)# end

在基于CLI的交换机上配置静态VLAN:

switch(enable) set vlan vlan-num [name name]

switch(enable) set vlan vlan-num mod-num/port-list

9. 在基于IOS的交换机上配置VLAN中继线:

switch(config)# interface interface mod/port

switch(config-if)# switchport mode trunk

switch(config-if)# switchport trunk encapsulation {isl dotlq}

switch(config-if)# switchport trunk allowed vlan remove vlan-list

switch(config-if)# switchport trunk allowed vlan add vlan-list

在基于CLI的交换机上配置VLAN中继线:

switch(enable) set trunk module/

port [on off desirable auto nonegotiate]

Vlan-range [isl dotlq dotl0 lane negotiate]

10.在基于IOS的交换机上配置VTP管理域:

switch# vlan database

switch(vlan)# vtp domain domain-name

在基于CLI的交换机上配置VTP管理域:

switch(enable) set vtp [domain domain-name]
11.在基于IOS的交换机上配置VTP 模式:

switch# vlan database

switch(vlan)# vtp domain domain-name

switch(vlan)# vtp {sever cilent transparent}

switch(vlan)# vtp password password

在基于CLI的交换机上配置VTP 模式:

switch(enable) set vtp [domain domain-name] [mode{ sever cilent transparent }][password password]

12. 在基于IOS的交换机上配置VTP版本:

switch# vlan database

switch(vlan)# vtp v2-mode

在基于CLI的交换机上配置VTP版本:

switch(enable) set vtp v2 enable

13. 在基于IOS的交换机上启动VTP剪裁:

switch# vlan database

switch(vlan)# vtp pruning

在基于CL I 的交换机上启动VTP剪裁:

switch(enable) set vtp pruning enable

14.在基于IOS的交换机上配置以太信道:

switch(config-if)# port group group-number [distribution {source destination}]

在基于CLI的交换机上配置以太信道:

switch(enable) set port channel moudle/port-range mode{on off desirable auto}

15.在基于IOS的交换机上调整根路径成本:

switch(config-if)# spanning-tree [vlan vlan-list] cost cost

在基于CLI的交换机上调整根路径成本:

switch(enable) set spantree portcost moudle/port cost

switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list]

16.在基于IOS的交换机上调整端口ID:

switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority

在基于CLI的交换机上调整端口ID:

switch(enable) set spantree portpri {mldule/port}priority

switch(enable) set spantree portvlanpri {module/port}priority [vlans]
17. 在基于IOS的交换机上修改STP时钟:

switch(config)# spanning-tree [vlan vlan-list] hello-time seconds

switch(config)# spanning-tree [vlan vlan-list] forward-time seconds

switch(config)# spanning-tree [vlan vlan-list] max-age seconds

在基于CLI的交换机上修改STP时钟:

switch(enable) set spantree hello interval[vlan]

switch(enable) set spantree fwddelay delay [vlan]

switch(enable) set spantree maxage agingtiame[vlan]

18. 在基于IOS的交换机端口上启用或禁用Port Fast 特征:

switch(config-if)#spanning-tree portfast

在基于CLI的交换机端口上启用或禁用Port Fast 特征:

switch(enable) set spantree portfast {module/port}{enable disable}

19. 在基于IOS的交换机端口上启用或禁用UplinkFast 特征:

switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second]

在基于CLI的交换机端口上启用或禁用UplinkFast 特征:

switch(enable) set spantree uplinkfast {enable disab

le}[rate update-rate] [all-protocols off on]

20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP地址,然后使用下列命令: switch(config)# cluster enable cluster-name


21. 为了从一条中继链路上删除VLAN,可使用下列命令:

switch(enable) clear trunk module/port vlan-range

22. 用show vtp domain 显示管理域的VTP参数.

23. 用show vtp statistics显示管理域的VTP参数.

24. 在Catalyst交换机上定义TrBRF的命令如下:

switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp {ieee ibm}]

25. 在Catalyst交换机上定义TrCRF的命令如下:

switch (enable) set vlan vlan-num [name name] type trcrf

{ring hex-ring-num decring decimal-ring-num} parent vlan-num

26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口:

switch(enable) set vlan vlan-num mod-num/port-num

27. 命令show spantree显示一个交换机端口的STP状态.

28. 配置一个ELAN的LES和BUS,可以使用下列命令:

ATM (config)# interface atm number.subint multioint

ATM(config-subif)# lane serber-bus ethernet elan-name

29. 配置LECS:

ATM(config)# lane database database-name

ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address

ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address

ATM(lane-config-databade)# name …

30. 创建完数据库后,必须在主接口上启动LECS.命令如下:

ATM(config)# interface atm number

ATM(config-if)# lane config database database-name

ATM(config-if)# lane config auto-config-atm-address

31. 将每个LEC配置到一个不同的ATM子接口上.命令如下:

ATM(config)# interface atm number.subint multipoint

ATM(config)# lane client ethernet vlan-num elan-num

32. 用show lane server 显示LES的状态.

33. 用show lane bus显示bus的状态.

34. 用show lane database显示LECS数据库可内容.

35. 用show lane client显示LEC的状态.

36. 用show module显示已安装的模块列表.

37. 用物理接口建立与VLAN的连接:

router# configure terminal

router(config)# interface media module/port

router(config-if)# description description-string

router(config-if)# ip address ip-addr subnet-mask

router(config-if)# no shutdown

38. 用中继链路来建立与VLAN的连接:

router(config)# interface module/port.subinterface

router(config-ig)# encapsulation[isl dotlq] vlan-number

router(config-if)# ip address ip-address subnet-mask

39. 用LANE 来建立与VLAN的连接:

router(config)# interface atm module/port

router(config-if)# no ip address

router(config-if)# atm pvc 1 0 5 qsaal

router(config-if)# atm pvc 2 0 16 ilni

router(config-if)# interface atm module/port.subinterface multipoint

router(config-if)# ip addres

s ip-address subnet-mask

router(config-if)# lane client ethernet elan-num

router(config-if)# interface atm module/port.subinterface multipoint

router(config-if)# ip address ip-address subnet-name

router(config-if)# lane client ethernet elan-name

router(config-if)# …

40. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行:

router(config)# ip routing

router(config)# router ip-routing-protocol

router(config-router)# network ip-network-number

router(config-router)# network ip-network-number


41. 配置默认路由:

switch(enable) set ip route default gateway

42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令:

router(config)# interface interface number

router(config-if)# mls rp vlan-id vlan-id-num

43. 在路由处理器启用MLSP:

router(config)# mls rp ip

44. 为了把一个外置的路由处理器接口和交换机安置在同一个VTP域中:

router(config)# interface interface number

router(config-if)# mls rp vtp-domain domain-name

45. 查看指定的VTP域的信息:

router# show mls rp vtp-domain vtp domain name

46. 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令:

router(config-if)#mls rp management-interface

47. 要检验MLS-RP的配置情况:

router# show mls rp

48. 检验特定接口上的MLS配置:

router# show mls rp interface interface number

49. 为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表:

set mls flow [destination destination-source full]

50. 为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令:
router(config)# mls rp ip input-acl


51. 当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令:

switch(enable) set mls enable

52. 若想改变老化时间的值,可在特权模式下输入以下命令:

switch(enable) set mls agingtime agingtime

53. 设置快速老化:

switch(enable) set mls agingtime fast fastagingtime pkt_threshold

54. 确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定:

switch(enable) show mls include

55. 显示MLS高速缓存记录:

switch(enable) show mls entry

56. 用命令show in arp显示ARP高速缓存区的内容。

57. 要把路由器配置为HSRP备份组的成员,可以在接口配置模式下使用下面的命令:

router(config-if)# standby group-number ip ip-address

58. 为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下:

router(config-if)# standy group-number preempt

59. 访问时间和保持时间参数是可配置的:

router(config-if)# standy group-number timers hellotime holdtime

60. 配置HSRP跟踪:

router(config-if)# standy group-number track type-number interface

-priority

61. 要显示HSRP路由器的状态:

router# show standby type-number group brief

62. 用命令show ip igmp确定当选的查询器。

63. 启动IP组播路由选择:

router(config)# ip muticast-routing

64. 启动接口上的PIM:

dalllasr1>(config-if)# ip pim {dense-mode sparse-mode sparse-dense-mode}

65. 启动稀疏-稠密模式下的PIM:

router# ip multicast-routing

router# interface type number

router# ip pim sparse-dense-mode

66. 核实PIM的配置:

dallasr1># show ip pim interface[type number] [count]

67. 显示PIM邻居:

dallasr1># show ip neighbor type number

68. 为了配置RP的地址,命令如下:

dallasr1># ip pim rp-address ip-address [group-access-list-number][override]

69. 选择一个默认的RP:

dallasr1># ip pim rp-address

通告RP和它所服务的组范围:

dallasr1># ip pim send-rp-announce type number scope ttl group-list access-list-number

为管理范围组通告RP的地址:

dallasr1># ip pim send-rp-announce ethernet0 scope 16 group-list1

dallasr1># access-list 1 permit 266.0.0.0 0.255.255.255

设定一个RP映像代理:

dallasr1># ip pim send-rp-discovery scope ttl

核实组到RP的映像:

dallasr1># show ip pim rp mapping

dallasr1># show ip pim rp [group-name group-address] [mapping]

70. 在路由器接口上用命令ip multicast ttl-threshold ttl-value设定TTL阀值:

dallasr1>(config-if)# ip multicast ttl-threshold ttl-value


71. 用show ip pim neighbor显示PIM邻居表。

72. 显示组播通信路由表中的各条记录:

dallasr1>show ip mroute [group-name group-address][scoure][summary][count][active kbps]

73. 要记录一个路由器接受和发送的全部IP组播包:

dallasr1> #debug ip mpacket [detail] [access-list][group]

74. 要在CISCO路由器上配置CGMP:

dallasr1>(config-if)# ip cgmp

75.配置一个组播路由器,使之加入某一个特定的组播组:

dallasr1>(config-if)# ip igmp join-group group-address

76. 关闭 CGMP:

dallasr1>(config-if)# no ip cgmp

77. 启动交换机上的CGMP:

dallasr1>(enable) set cgmp enable

78. 核实Catalyst交换机上CGMP的配置情况:

catalystla1>(enable) show config

set prompt catalystla1>

set interface sc0 192.168.1.1 255.255.255.0

set cgmp enable

79. CGMP离开的设置:

Dallas_SW(enable) set cgmp leave

80. 在Cisco设备上修改控制端口密码:

R1(config)# line console 0

R1(config-line)# login

R1(config-line)# password Lisbon

R1(config)# enable password Lilbao

R1(config)# login local

R1(config)# username student password cisco

81. 在Cisco设备上设置控制台及vty端口的会话超时:

R1(config)# line console 0

R1(config-line)# exec-timeout 5 10

R1(config)# line vty 0 4

R1(config-line)# exec-timeout 5 2

82. 在Cisco设备上设定特权

级:

R1(config)# privilege configure level 3 username

R1(config)# privilege configure level 3 copy run start

R1(config)# privilege configure level 3 ping

R1(config)# privilege configure level 3 show run

R1(config)# enable secret level 3 cisco

83. 使用命令privilege 可定义在该特权级下使用的命令:

router(config)# privilege mode level level command

84. 设定用户特权级:

router(config)# enable secret level 3 dallas

router(config)# enable secret san-fran

router(config)# username student password cisco

85. 标志设置与显示:

R1(config)# banner motd ‘unauthorized access will be prosecuted!’


86. 设置vty访问:

R1(config)# access-list 1 permit 192.168.2.5

R1(config)# line vty 0 4

R1(config)# access-class 1 in

87. 配置HTTP访问:

Router3(config)# access-list 1 permit 192.168.10.7

Router3(config)# ip http sever

Router3(config)# ip http access-class 1

Router3(config)# ip http authentication local

Router3(config)# username student password cisco

88. 要启用HTTP访问,请键入以下命令:

switch(config)# ip http sever

89. 在基于set命令的交换机上用setCL1启动和核实端口安全:

switch(enable) set port security mod_num/port_num…enable mac address

switch(enable) show port mod_num/port_num

在基于CiscoIOS命令的交换机上启动和核实端口安全:

switch(config-if)# port secure [mac-mac-count maximum-MAC-count]

switch# show mac-address-table security [type module/port]

90. 用命令access-list在标准通信量过滤表中创建一条记录:

Router(config)# access-list access-list-number {permit deny} source-address [source-address]

91. 用命令access-list在扩展通信量过滤表中创建一条记录:

Router(config)# access-list access-list-number {permit deny{protocol protocol-keyword}}{source source-wildcard any}{destination destination-wildcard any}[protocol-specific options][log]

92. 对于带内路由更新,配置路由更新的最基本的命令格式是:

R1(config-router)#distribute-list access-list-number name in [type number]

93. 对于带外路由更新,配置路由更新的最基本的命令格式是:

R1(config-router)#distribute-list access-list-number name out [interface-name] routing-process autonomous-system-number

94. set snmp命令选项:

set snmp community {read-only ready-write read-write-all}[community_string]

95. set snmp trap 命令格式如下:

set snmp trap {enable disable}

[all moudle classis bridge repeater auth vtp ippermit vmps config entity stpx]

set snmp trap rvcr_addr rcvr_community

96. 启用SNMP chassis 陷阱:

Console>(enable) set snmp trap enable chassis

97. 启用所有SNMP chassis 陷阱:

Console>(enable) set snmp trap enable

98. 禁用SNMP chassis 陷阱:

Console>(enable) set snmp

trap disable chassis

99. 给SNMP陷阱接收表加一条记录:

Console>(enable) set snmp trap 192.122.173.42 public

100. show snmp 输出结果。

101. 命令set snmp rmon enable 的输出结果。

102. 显示SPAN信息:

Consile> show span


相关文档
相关文档 最新文档