机械设计与制造英文翻译

外文翻译

How to extend the service life of bearing

Nature's harsh working conditions can lead to the failure of bearing, but if you follow some simple rules, opportunities for normal operation of the bearing can be improved. In the using process of bearing,extreme neglect in a bearing leads to overheating and possibly seizure or, at worst, an explosion. But even a failed bearing leaves clues as to what went wrong. After a little detective work, action can be taken to avoid a repeat performance.Some of the reasons for bearing failure, but common is incorrect use of improper use, pollution, lubricants, loading and unloading or handling damage and installation error, etc. The problem is often not difficult to diagnose, because of a failed bearing usually leaving the slightest trace what went wrong. However，while a postmortem yields good information，it is better to avoid the process altogether by specifying the bearing correctly in The first place．To do this，it is useful to review the manufacturers sizing guidelines and operating characteristics for the selected bearing.Equally important is the research requirement of noise, torque, beating, and possible exposure to pollutants, hostile liquid, and extreme temperatures. Whether can provide further clues bearing is suitable for this work.

1 bearing failure reason

About 40% of ball bearing failures are caused by contamination from dust, dirt, shavings, and corrosion. Contamination also causes torque and noise problems, and is often the result of improper handling or the application environment．Fortunately, a bearing failure caused by environment or handling contamination is preventable，and a simple visual examination can easily identify the cause．

Conducting a postmortem illustrates what to look for on a failed or failing bearing．Then，understanding the mechanism behind the failure, such as brinelling or fatigue, helps eliminate the source of the problem.

Brinelling is one type of bearing failure easily avoided by proper handing and assembly. It is characterized by indentations in the bearing raceway caused by shock loading－such as when a bearing is dropped-or incorrect assembly. Brinelling usually occurs when loads exceed the material yield point(350,000 psi in SAE 52100 chrome steel)．It may also be caused by improper assembly, Which places a load across the races．Raceway dents also produce noise，vibration，and increased torque.

A similar defect is a pattern of elliptical dents caused by balls vibrating between raceways while the bearing is not turning．This problem is called false brinelling. It occurs on equipment in transit or that vibrates when not in operation. In addition, debris created by false brinelling acts like an abrasive, further contaminating the bearing. Unlike brinelling, false binelling is often indicated by a reddish color from fretting corrosion in the lubricant.

False brinelling is prevented by eliminating vibration sources and keeping the bearing well lubricated. Isolation pads on the equipment or a separate foundation may be required to reduce

environmental vibration. Also a light preload on the bearing helps keep the balls and raceway in tight contact. Preloading also helps prevent false brinelling during transit.

Seizures can be caused by a lack of internal clearance, improper lubrication, or excessive loading. Before seizing, excessive, friction and heat softens the bearing steel. Overheated bearings often change color，usually to blue-black or straw colored．Friction also causes stress in the retainer，which can break and hasten bearing failure．

Premature material fatigue is caused by a high load or excessive preload．When these conditions are unavoidable，bearing life should be carefully calculated so that a maintenance scheme can be worked out．

Another solution for fighting premature fatigue is changing material．When standard bearing materials，such as 440C or SAE 52100，do not guarantee sufficient life，specialty materials can be recommended. In addition，when the problem is traced back to excessive loading，a higher capacity bearing or different configuration may be used．

Creep is less common than premature fatigue．In bearings．it is caused by excessive clearance between bore and shaft that allows the bore to rotate on the shaft．Creep can be expensive because it causes damage to other components in addition to the bearing．0ther more likely creep indicators are scratches，scuff marks，or discoloration to shaft and bore．To prevent creep damage，the bearing housing and shaft fittings should be visually checked．Misalignment is related to creep in that it is mounting related．If races are misaligned or cocked．The balls track in a noncircumferencial path．The problem is incorrect mounting or tolerancing，or insufficient squareness of the bearing mounting site．Misalignment of more than 1/4·can cause an early failu re．Contaminated lubricant is often more difficult to detect than misalignment or creep．Contamination shows as premature wear．Solid contaminants become an abrasive in the lubricant．In addition。

insufficient lubrication between ball and retainer wears and weakens the retainer．In this situation，lubrication is critical if the retainer is a fully machined type．Ribbon or crown retainers，in contrast，allow lubricants to more easily reach all surfaces．Rust is a form of moisture contamination and often indicates the wrong material for the application．If the material checks out for the job，the easiest way to prevent rust is to keep bearings in their packaging，until just before installation．

2 Avoiding failures

The best way to handle bearing failures is to avoid them．This can be done in the selection process by recognizing critical performance characteristics．These include noise，starting and running torque，stiffness，nonrepetitive runout，and radial and axial play．In some applications, these items are so critical that specifying an ABEC level alone is not sufficient．

Torque requirements are determined by the lubricant，retainer，raceway quality(roundness cross curvature and surface finish)，and whether seals or shields are used．Lubricant viscosity must be selected carefully because inappropriate lubricant，especially in miniature bearings，causes excessive torque．Also，different lubricants have varying noise characteristics that should be matched to the application. For example，greases produce more noise than oil．

Nonrepetitive runout(NRR)occurs during rotation as a random eccentricity between the inner and outer races，much like a cam action．NRR can be caused by retainer tolerance or eccentricities of the raceways and balls．Unlike repetitive runout, no compensation can be made for NRR.

NRR is reflected in the cost of the bearing．It is common in the industry to provide different bearing types and grades for specific applications．For example，a bearing with an NRR of less than 0.3um is used when minimal runout is needed，such as in disk—drive spindle motors．Similarly，machine—tool spindles

tolerate only minimal deflections to maintain precision cuts．Consequently, bearings are manufactured with low NRR just for machine-tool applications．

Contamination is unavoidable in many industrial products，and shields and seals are commonly used to protect bearings from dust and dirt．However，a perfect bearing seal is not possible because of the movement between inner and outer races．Consequently，lubrication migration and contamination are always problems．

Once a bearing is contaminated, its lubricant deteriorates and operation becomes noisier．If it overheats，the bearing can seize．At the very least，contamination causes wear as it works between balls and the raceway，becoming imbedded in the races and acting as an abrasive between metal surfaces．Fending off dirt with seals and shields illustrates some methods for controlling contamination．Noise is as an indicator of bearing quality．Various noise grades have been developed to classify bearing performance capabilities．

Noise analysis is done with an Anderonmeter, which is used for quality control in bearing production and also when failed bearings are returned for analysis. A transducer is attached to the outer ring and the inner race is turned at 1,800rpm on an air spindle. Noise is measured in andirons, which represent ball displacement in μm/rad.

With experience, inspectors can identify the smallest flaw from their sound. Dust, for example, makes an irregular crackling. Ball scratches make a consistent popping and are the most difficult to identify. Inner-race damage is normally a constant high-pitched noise, while a damaged outer race makes an intermittent sound as it rotates.

Bearing defects are further identified by their frequencies. Generally, defects are separated into low, medium, and high wavelengths. Defects are also referenced to the number of irregularities per revolution.

Low-band noise is the effect of long-wavelength irregularities that occur about 1.6 to 10 times per revolution. These are caused by a variety of inconsistencies, such as pockets in the race. Detectable pockets are manufacturing flaws and result when the race is mounted too tightly in multiplejaw chucks.

Medium-hand noise is characterized by irregularities that occur 10 to 60 times per revolution. It is caused by vibration in the grinding operation that produces balls and raceways. High-hand irregularities occur at 60 to 300 times per revolution and indicate closely spaced chatter marks or widely spaced, rough irregularities.

Classifying bearings by their noise characteristics allows users to specify a noise grade in addition to the ABEC standards used by most manufacturers. ABEC defines physical tolerances such as bore, outer diameter, and runout. As the ABEC class number increase (from 3 to 9), tolerances are tightened. ABEC class, however, does not specify other bearing characteristics such as raceway quality, finish, or noise. Hence, a noise classification helps improve on the industry standard.

译文：

如何延长轴承寿命

自然界苛刻的工作条件会导致轴承的失效，但是如果遵循一些简单的规则，轴承正常运转的机会是能够被提高的。在轴承的使用过程当中，极端忽视轴承导致过热和可能发作,或在最坏的情况下,发生爆炸。但是一个被损坏的轴承，会留下它为什么被损坏的线索。通过一些细致的侦察工作，我们可以可以采取行动,以避免重复的性能。

导致轴承失效的原因很多，但常见的是不正确的使用、污染、润滑剂使用不当、装卸或搬运时的损伤及安装误差等。这个问题往往不是很难诊断,因为一个失败的轴承通常留下蛛丝马迹哪里出了问题。然而，当

事后的调查分析提供出宝贵的信息时，最好首先通过正确地选定轴承来完全避免失效的发生。为了做到这一点，再考察一下制造厂商的尺寸定位指南和所选轴承的使用特点是非常重要的。同样重要的是噪声的研究要求,转矩,跳动,以及可能的暴露于污染物,敌对的液体,和极端温度。这可以提供进一步的线索轴承是否适合工作。

1 轴承失效的原因

大约40%的球轴承故障是由污染引起的灰尘、污垢,刨花和腐蚀。污染也导致转矩和噪声问题,往往是由于操作不当或应用程序。由环境和污染所产生的轴承失效是可以预防的，而且通过简单的肉眼观察是可以确定产生这类失效的原因。进行后期给出了寻找失败或失败的轴承,然后理解失败背后的机制,如渗碳硬化或疲劳,有助于消除问题的根源。

只要使用和安装合理，轴承的剥蚀是容易避免的。剥蚀的特征是在轴承圈滚道上留有由冲击载荷或不正确的安装产生的压痕。剥蚀通常是在载荷超过材料屈服极限时发生的。如果安装不正确从而使某一载荷横穿轴承圈也会产生剥蚀。轴承圈上的压坑还会产生噪声、振动和附加扭矩。

类似的一种缺陷是当轴承不旋转时由于滚珠在轴承圈间振动而产生的椭圆形压痕。这种破坏称为低荷振蚀。这种破坏在运输中的设备和不工作时仍振动的设备中都会产生。此外，低荷振蚀产生的碎屑的作用就象磨粒一样，会进一步损害轴承。与剥蚀不同，低荷振蚀的特征通常是由于微振磨损腐蚀在润滑剂中会产生淡红色。

消除振动源并保持良好的轴承润滑可以防止低荷振蚀。给设备加隔离垫或对底座进行隔离可以减轻环境的振动。另外在轴承上加一个较小的预载荷不仅有助于滚珠和轴承圈保持紧密的接触，并且对防止在设备运输中产生的低荷振蚀也有帮助。

造成轴承卡住的原因是缺少内隙、润滑不当和载荷过大。在卡住之前，过大的摩擦和热量使轴承钢软化。过热的轴承通常会改变颜色，一般会变成蓝黑色或淡黄色。摩擦还会使保持架受力，这会破坏支承架，并加速轴承的失效。

材料过早出现疲劳破坏是由重载后过大的预载引起的。如果这些条件不可避免，就应仔细计算轴承寿命，以制定一个维护计划。

另一个解决办法是更换材料。若标准的轴承材料不能保证足够的轴承寿命，就应当采用特殊的材料。另外，如果这个问题是由于载荷过大造成的，就应该采用抗载能力更强或其他结构的轴承。

蠕动不象过早疲劳那样普遍。轴承的蠕动是由于轴和内圈之间的间隙过大造成的。蠕动的害处很大，它不仅损害轴承，也破坏其他零件。

蠕动的明显特征是划痕、擦痕或轴与内圈的颜色变化。为了防止蠕动，应该先用肉眼检查一下轴承箱件和轴的配件。

蠕动与安装不正有关。如果轴承圈不正或翘起，滚珠将沿着一个非圆周轨道运动。这个问题是由于安装不正确或公差不正确或轴承安装现场的垂直度不够造成的。如果偏斜超过0.25°，轴承就会过早地失效。

检查润滑剂的污染比检查装配不正或蠕动要困难得多。污染的特征是使轴承过早的出现磨损。润滑剂中的固体杂质就象磨粒一样。如果滚珠和保持架之间润滑不良也会磨损并削弱保持架。在这种情况下，润滑对于完全加工形式的保持架来说是至关重要的。相比之下，带状或冠状保持架能较容易地使润滑剂到达全部表面。

锈是湿气污染的一种形式，它的出现常常表明材料选择不当。如果某一材料经检验适合工作要求，那么防止生锈的最简单的方法是给轴承包装起来，直到安装使用时才打开包装。

2 避免失效的方法

解决轴承失效问题的最好办法就是避免失效发生。这可以在选用过程中通过考虑关键性能特征来实现。这些特征包括噪声、起动和运转扭矩、刚性、非重复性振摆以及径向和轴向间隙。

扭矩要求是由润滑剂、保持架、轴承圈质量（弯曲部分的圆度和表面加工质量）以及是否使用密封或遮护装置来决定。润滑剂的粘度必须认真加以选择，因为不适宜的润滑剂会产生过大的扭矩，这在小型轴承中尤其如此。另外，不同的润滑剂的噪声特性也不一样。举例来说，润滑脂产生的噪声比润滑油大一些。因此，要根据不同的用途来选用润滑剂。

在轴承转动过程中，如果内圈和外圈之间存在一个随机的偏心距，就会产生与凸轮运动非常相似的非重复性振摆（NRR）。保持架的尺寸误差和轴承圈与滚珠的偏心都会引起NRR。和重复性振摆不同的是，NRR是没有办法进行补偿的。

在工业中一般是根据具体的应用来选择不同类型和精度等级的轴承。例如，当要求振摆最小时，轴承的非重复性振摆不能超过0.3微米。同样，机床主轴只能容许最小的振摆，以保证切削精度。因此在机床的应用中应该使用非重复性振摆较小的轴承。

在许多工业产品中，污染是不可避免的，因此常用密封或遮护装置来保护轴承，使其免受灰尘或脏物的侵蚀。但是，由于轴承内外圈的运动，使轴承的密封不可能达到完美的程度，因此润滑油的泄漏和污染始终是一个未能解决的问题。

一旦轴承受到污染，润滑剂就要变质，运行噪声也随之变大。如果轴承过热，它将会卡住。当污染物处于滚珠和轴承圈之间时，其作用和金属表面之间的磨粒一样，会使轴承磨损。采用密封和遮护装置来挡开脏物是控制污染的一种方法。

噪声是反映轴承质量的一个指标。轴承的性能可以用不同的噪声等级来表示。

噪声的分析是用安德逊计进行的，该仪器在轴承生产中可用来控制质量，也可对失效的轴承进行分析。将一传感器连接在轴承外圈上，而内圈在心轴以1800r/min的转速旋转。测量噪声的单位为anderon。即用um/rad表示的轴承位移。

根据经验，观察者可以根据声音辨别出微小的缺陷。例如，灰尘产生的是不规则的劈啪声；滚珠划痕产生一种连续的爆破声，确定这种划痕最困难；内圈损伤通常产生连续的高频噪声，而外圈损伤则产生一种间歇的声音。

轴承缺陷可以通过其频率特性进一步加以鉴定。通常轴承缺陷被分为低、中、高三个波段。缺陷还可以根据轴承每转动一周出现的不规则变化的次数加以鉴定。

低频噪声是长波段不规则变化的结果。轴承每转一周这种不规则变化可出现1.6~10次，它们是由各种干涉（例如轴承圈滚道上的凹坑）引起的。可察觉的凹坑是一种制造缺陷，它是在制造过程中由于多爪卡盘夹的太紧而形成的。

中频噪声的特征是轴承每旋转一周不规则变化出现10~60次。这种缺陷是由在轴承圈和滚珠的磨削加工中出现的振动引起的。轴承每旋转一周高频不规则变化出现60~300次，它表明轴承上存在着密集的振痕或大面积的粗糙不平。利用轴承的噪声特性对轴承进行分类，用户除了可以确定大多数厂商所使用的ABEC标准外，还可确定轴承的噪声等级。ABEC标准只定义了诸如孔、外径、振摆等尺寸公差。随着ABEC级别的增加（从3增到9），公差逐渐变小。ABEC类,然而,没有指定其他轴承特征如水沟质量、完成或噪音。因此,噪声分类有助于提高行业标准。

毕设外文资料翻译.

理工学院 毕业设计外文资料翻译 专业：计算机科学与技术 姓名：马艳丽 学号： 12L0752218 外文出处：The Design and Implementation of 3D Electronic Map of Campus Based on WEBGIS 附件： 1.外文资料翻译译文；2.外文原文。

附件1：外文资料翻译译文 基于WebGIS的校园三维电子地图的设计与实现 一．导言 如今，数字化和信息化是当今时代的主题。随着信息革命和计算机科学的发展，计算机技术已经渗透到科学的各个领域，并引起了许多革命性的变化，在这些科目，古代制图学也不例外。随着技术和文化的不断进步，地图变化的形式和内容也随之更新。在计算机图形学中，地理信息系统（GIS）不断应用到Web，制作和演示的传统方式经历了巨大的变化，由于先进的信息技术的发展，地图的应用已经大大延长。在这些情况下，绘图将面临广阔的发展前景。电子地图是随之应运而生的产品之一。随着计算机技术，计算机图形学理论，遥感技术，航空摄影测量技术和其他相关技术的飞速发展。用户需要的三维可视化，动态的交互性和展示自己的各种地理相关的数据处理和分析，如此多的关注应支付的研究三维地图。东北石油大学及其周边地区的基础上本文设计并建立三维电子地图。 二．系统设计 基于WebGIS的校园三维电子地图系统的具有普通地图的一般特性。通过按键盘上的箭头键（上，下，左，右），可以使地图向相应的方向移动。通过拖动鼠标，可以查看感兴趣的任何一个地方。使用鼠标滚轮，可以控制地图的大小，根据用户的需求来查看不同缩放级别的地图。在地图的左下角会显示当前鼠标的坐标。在一个div层，我们描绘了一个新建筑物的热点，这层可以根据不同的地图图层的显示，它也可以自动调整。通过点击热点，它可以显示热点的具体信息。也可以输入到查询的信息，根据自己的需要，并得到一些相关的信息。此外，通过点击鼠标，人们可以选择检查的三维地图和卫星地图。 主要功能包括： ?用户信息管理：检查用户名和密码，根据权限设置级别的认证，允许不同权限的用户通过互联网登录系统。 ?位置信息查询：系统可以为用户提供模糊查询和快速定位。

机械毕业设计英文外文翻译460数字控制 (2)

附录 科技译文： Numerical Control Numerical Control(NC) is a method of controlling the movements of machineComponents by directly inserting coded instructions in the form of numerical data(numbers and data ) into the system.The system automatically interprets these data and converts to output signals. These signals ,in turn control various machine components ,such as turning spindles on and off ,changing tools,moving the work piece or the tools along specific paths,and turning cutting fluits on and off. In order to appreciate the importer of numerical control of machines ,let’s briefly review how a process such as machining has been carried out traditionally .After studying the working drawing of a part, the operator sets up the appropriate process parameters(such as cutting speed ,feed,depth of cut,cutting fluid ,and so on),determines the sequence of operations to be performed,clamps the work piece in a workholding device such as chuck or collet ,and proceeds to make the part .Depending on part shape and the dimensional accuracy specified ,this approach usually requires skilled

机械工程英语翻译

Unit1 1、What is the difference between an alloy and a pure metal? Pure metals are elements which come from a particular area of the periodic table. Examples of pure metals include copper in electrical wires and aluminum in cooking foil and beverage cans. 合金与纯金属的区别是什么？纯金属是在元素周期表中占据特定位置的元素。例如电线中的铜和制造烹饪箔及饮料罐的铝。 Alloys contain more than one metallic element. Their properties can be changed by changing the elements present in the alloy. Examples of metal alloys include stainless steel which is an alloy of iron, nickel, and chromium; and gold jewelry which usually contains an alloy of gold and nickel. 合金包含不止一种金属元素。合金的性质能通过改变其中存在的元素而改变。金属合金的例子有：不锈钢是一种铁、镍、铬的合金，以及金饰品通常含有金镍合金。 2、 Why are metals and alloys used? Many metals and alloys have high densities and are used in applications which require a high mass-to-volume ratio. 为什么要使用金属和合金？许多金属和合金具有高密度，因此被用在需要较高质量体积比的场合。 Some metal alloys,such as those based on aluminum, have low densities and are used in aerospace applications for fuel economy. Many alloys also have high fracture toughness, which means they can withstand impact and are durable. 某些金属合金，例如铝基合金，其密度低，可用于航空航天以节约燃料。许多合金还具有高断裂韧性，这意味着它们能经得起冲击并且是耐用的。 3、The atomic bonding of metals also affects their properties. In m etals, the outer valence electrons are shared among all atoms, and ar e free to travel everywhere. Since electrons conduct heat and electri city, metals make good cooking pans and electrical wires. 金属的原子连结对它们的特性也有影响。在金属内部，原子的外层阶电子由所有原子共享并能到处自由移动。由于电子能导热和导电，所以用金属可以制造好的烹饪锅和电线。 It is impossible to see through metals, since these valence electrons absorb any photons of light which reach the metal. No photons pass through. 因为这些阶电子吸收到达金属的光子，所以透过金属不可能看得见。没有光子能通过金属. 4、Some of the useful properties of ceramics and glasses include high melting temperature, low density, high strength, stiffness, hardness, wear resistance, and corrosion resistance. 陶瓷和玻璃的特性高熔点、低密度、高强度、高刚度、高硬度、高耐磨性和

毕业设计外文翻译附原文

外文翻译 专业机械设计制造及其自动化学生姓名刘链柱 班级机制111 学号1110101102 指导教师葛友华

外文资料名称： Design and performance evaluation of vacuum cleaners using cyclone technology 外文资料出处：Korean J. Chem. Eng., 23(6), (用外文写) 925-930 (2006) 附件： 1.外文资料翻译译文 2.外文原文

应用旋风技术真空吸尘器的设计和性能介绍 吉尔泰金，洪城铱昌，宰瑾李， 刘链柱译 摘要：旋风型分离器技术用于真空吸尘器 - 轴向进流旋风和切向进气道流旋风有效地收集粉尘和降低压力降已被实验研究。优化设计等因素作为集尘效率，压降，并切成尺寸被粒度对应于分级收集的50％的效率进行了研究。颗粒切成大小降低入口面积，体直径，减小涡取景器直径的旋风。切向入口的双流量气旋具有良好的性能考虑的350毫米汞柱的低压降和为1.5μm的质量中位直径在1米3的流量的截止尺寸。一使用切向入口的双流量旋风吸尘器示出了势是一种有效的方法，用于收集在家庭中产生的粉尘。 摘要及关键词：吸尘器; 粉尘; 旋风分离器 引言 我们这个时代的很大一部分都花在了房子，工作场所，或其他建筑，因此，室内空间应该是既舒适情绪和卫生。但室内空气中含有超过室外空气因气密性的二次污染物，毒物，食品气味。这是通过使用产生在建筑中的新材料和设备。真空吸尘器为代表的家电去除有害物质从地板到地毯所用的商用真空吸尘器房子由纸过滤，预过滤器和排气过滤器通过洁净的空气排放到大气中。虽然真空吸尘器是方便在使用中，吸入压力下降说唱空转成比例地清洗的时间，以及纸过滤器也应定期更换，由于压力下降，气味和细菌通过纸过滤器内的残留粉尘。 图1示出了大气气溶胶的粒度分布通常是双峰形，在粗颗粒（>2.0微米）模式为主要的外部来源，如风吹尘，海盐喷雾，火山，从工厂直接排放和车辆废气排放，以及那些在细颗粒模式包括燃烧或光化学反应。表1显示模式，典型的大气航空的直径和质量浓度溶胶被许多研究者测量。精细模式在0.18?0.36 在5.7到25微米尺寸范围微米尺寸范围。质量浓度为2?205微克，可直接在大气气溶胶和 3.85至36.3μg/m3柴油气溶胶。

机械毕业设计英文外文翻译204机电一体化

附录 INTEGRATION OF MACHINERY （From ELECTRICAL AND MACHINERY INDUSTRY）ABSTRACT Machinery was the modern science and technology development inevitable result, this article has summarized the integration of machinery technology basic outline and the development background .Summarized the domestic and foreign integration of machinery technology present situation, has analyzed the integration of machinery technology trend of development. Key word：integration of machinery ，technology，present situation ，product t，echnique of manufacture ，trend of development 0. Introduction modern science and technology unceasing development, impelled different discipline intersecting enormously with the seepage, has caused the project domain technological revolution and the transformation .In mechanical engineering domain, because the microelectronic technology and the computer technology rapid development and forms to the mechanical industry seepage the integration of machinery, caused the mechanical industry the technical structure, the product organization, the function and the constitution, the production method and the management system has had the huge change, caused the industrial production to enter into “the integration of machinery” by “the machinery electrification” for the characteristic development phase. 1. Integration of machinery outline integration of machinery is refers in the organization new owner function, the power function, in the information processing function and the control function introduces the electronic technology, unifies the system the mechanism and the computerization design and the software which constitutes always to call. The integration of machinery development also has become one to have until now own system new discipline, not only develops along with the science and technology, but also entrusts with the new content .But its basic characteristic may summarize is: The integration of machinery is embarks from the system viewpoint, synthesis community technologies and so on utilization mechanical technology, microelectronic technology, automatic control technology,

机械工程专业英语翻译合集

1.我们可以把钢再次加热到临界温度以下的某一温度，然后在慢慢让其冷却。We can heat the steel again to a temperature below the critical temperature, then cool it slowly. 2.无论任何简单的机床，都是由单一元件即通称为机械零件或部件组成的。However simple, any machine is a combination of individual components generally referred to as machine elements or parts. 3.这些金属不都是好的导体。 All these metals are not good conductors. 4. 在做带电实验的时候，再怎么小心都不为过。 You can't be too careful in performing an experiment. 5.利用发电机可以把机械能转变成电能。 The mechanical energy can be changed back into electrical energy by means of a generator or dynamo. 6.假定电源输入的电压保持不变。 Assume that the voltage input of the power supply remains the same. 7.化石燃料是发电过程中最为频繁使用的能源。 Fossil fuels are most frequently used source daring the power generation process. 8单个机械零件的可靠性成为评估整台机器使用寿命的基本因素。 The individual reliability of machine elements becomes the basis for estimating the overall life 9.说我们生活在一个电子时代，这一点都不夸张。 It's no exaggeration to say that we live in an electronic age. 10.发动机的转速不应超过最大允许值。 Engine revolution should not exceed the maximum permissible. 11.如能从大型核电站获得成本极低的电力，电解氢的竞争能力就会增强。（Electrolytic hydrogen）。 If extremely low-cost power were ever to become available from large nuclear power plants, electrolytic hydrogen would become competitive. 12.电子技术提供了一种新的显示时间的方法。 A new way of displaying time has been given by electronics. 13.远距离输电需要高压，安全用电需要低压。 High voltage is necessary for long transmission line while low voltage for safe use. 14.铝的电阻大约是同等尺寸的铜的1.5倍。 The resistance of aluminum is approximately half again as great as that of copper for the same dimensions = size 15.In fact,it is impossible for no force to be exerted on a body,since in this world everything is subject to the for ce of gravity. 事实上，物体不受外力作用是不可能的，因为在这个世界上任何物体都要受到重力的作用。 16.In a thermal power plant,all the chemical energy is not

毕业设计英文翻译

使用高级分析法的钢框架创新设计 1．导言 在美国，钢结构设计方法包括允许应力设计法(ASD)，塑性设计法(PD)和荷载阻力系数设计法(LRFD)。在允许应力设计中，应力计算基于一阶弹性分析，而几何非线性影响则隐含在细部设计方程中。在塑性设计中，结构分析中使用的是一阶塑性铰分析。塑性设计使整个结构体系的弹性力重新分配。尽管几何非线性和逐步高产效应并不在塑性设计之中，但它们近似细部设计方程。在荷载和阻力系数设计中，含放大系数的一阶弹性分析或单纯的二阶弹性分析被用于几何非线性分析，而梁柱的极限强度隐藏在互动设计方程。所有三个设计方法需要独立进行检查，包括系数K计算。在下面，对荷载抗力系数设计法的特点进行了简要介绍。 结构系统内的内力及稳定性和它的构件是相关的，但目前美国钢结构协会（AISC）的荷载抗力系数规范把这种分开来处理的。在目前的实际应用中，结构体系和它构件的相互影响反映在有效长度这一因素上。这一点在社会科学研究技术备忘录第五录摘录中有描述。 尽管结构最大内力和构件最大内力是相互依存的（但不一定共存），应当承认，严格考虑这种相互依存关系，很多结构是不实际的。与此同时，众所周知当遇到复杂框架设计中试图在柱设计时自动弥补整个结构的不稳定（例如通过调整柱的有效长度）是很困难的。因此，社会科学研究委员会建议在实际设计中，这两方面应单独考虑单独构件的稳定性和结构的基础及结构整体稳定性。图28.1就是这种方法的间接分析和设计方法。

在目前的美国钢结构协会荷载抗力系数规范中，分析结构体系的方法是一阶弹性分析或二阶弹性分析。在使用一阶弹性分析时，考虑到二阶效果，一阶力矩都是由B1,B2系数放大。在规范中，所有细部都是从结构体系中独立出来，他们通过细部内力曲线和规范给出的那些隐含二阶效应，非弹性，残余应力和挠度的相互作用设计的。理论解答和实验性数据的拟合曲线得到了柱曲线和梁曲线，同时Kanchanalai发现的所谓“精确”塑性区解决方案的拟合曲线确定了梁柱相互作用方程。 为了证明单个细部内力对整个结构体系的影响，使用了有效长度系数，如图28.2所示。有效长度方法为框架结构提供了一个良好的设计。然而，有效长度方法的

毕设英文翻译英文版

72页 Machine Tools Objectived. Machine tools are the main engines of the manufacturing industry. This chapter covers a few of the details that are common to all classes of machine tools discussed in this book. After completing the chapter, the reader will be able to >understand the classification of the various machine tools used in manufacturing industries. >identify the differences between generating and forming of surfaces. > identify various methods used to generate different types of surfaces. >distinguish between the different accuracies and surface finishes that are achievable with different machine tools. >understand the different components of the machine tools and their functions. >learn about the different support structures used in the machine tools. >understand the various actuation systems that are useful to generate the required surfaces. >Learn the different types of guideways used in the machine tools. >understand the work holding requirements. 3.1 INTRODUCTION The earliest known machine tools are the Egyptian foot-operated lathes.

机械类毕业设计外文翻译

本科毕业论文(设计) 外文翻译 学院：机电工程学院 专业：机械工程及自动化 姓名：高峰 指导教师：李延胜 2011年05 月10日 教育部办公厅 Failure Analysis，Dimensional Determination And

Analysis，Applications Of Cams INTRODUCTION It is absolutely essential that a design engineer know how and why parts fail so that reliable machines that require minimum maintenance can be designed．Sometimes a failure can be serious，such as when a tire blows out on an automobile traveling at high speed．On the other hand，a failure may be no more than a nuisance．An example is the loosening of the radiator hose in an automobile cooling system．The consequence of this latter failure is usually the loss of some radiator coolant，a condition that is readily detected and corrected．The type of load a part absorbs is just as significant as the magnitude．Generally speaking，dynamic loads with direction reversals cause greater difficulty than static loads，and therefore，fatigue strength must be considered．Another concern is whether the material is ductile or brittle．For example，brittle materials are considered to be unacceptable where fatigue is involved． Many people mistakingly interpret the word failure to mean the actual breakage of a part．However，a design engineer must consider a broader understanding of what appreciable deformation occurs．A ductile material，however will deform a large amount prior to rupture．Excessive deformation，without fracture，may cause a machine to fail because the deformed part interferes with a moving second part．Therefore，a part fails(even if it has not physically broken)whenever it no longer fulfills its required function．Sometimes failure may be due to abnormal friction or vibration between two mating parts．Failure also may be due to a phenomenon called creep，which is the plastic flow of a material under load at elevated temperatures．In addition，the actual shape of a part may be responsible for failure．For example，stress concentrations due to sudden changes in contour must be taken into account．Evaluation of stress considerations is especially important when there are dynamic loads with direction reversals and the material is not very ductile． In general，the design engineer must consider all possible modes of failure，which include the following． ——Stress ——Deformation ——Wear ——Corrosion ——Vibration ——Environmental damage ——Loosening of fastening devices

机械工程专业英语 翻译

2、应力和应变 在任何工程结构中独立的部件或构件将承受来自于部件的使用状况或工作的外部环境的外力作用。如果组件就处于平衡状态,由此而来的各种外力将会为零,但尽管如此,它们共同作用部件的载荷易于使部件变形同时在材料里面产生相应的内力。 有很多不同负载可以应用于构件的方式。负荷根据相应时间的不同可分为: (a)静态负荷是一种在相对较短的时间内逐步达到平衡的应用载荷。 (b)持续负载是一种在很长一段时间为一个常数的载荷, 例如结构的重量。这种类型的载荷以相同的方式作为一个静态负荷; 然而,对一些材料与温度和压力的条件下,短时间的载荷和长时间的载荷抵抗失效的能力可能是不同的。 (c)冲击载荷是一种快速载荷(一种能量载荷)。振动通常导致一个冲击载荷, 一般平衡是不能建立的直到通过自然的阻尼力的作用使振动停止的时候。 (d)重复载荷是一种被应用和去除千万次的载荷。 (e)疲劳载荷或交变载荷是一种大小和设计随时间不断变化的载荷。 上面已经提到，作用于物体的外力与在材料里面产生的相应内力平衡。因此,如果一个杆受到一个均匀的拉伸和压缩，也就是说, 一个力,均匀分布于一截面,那么产生的内力也均匀分布并且可以说杆是受到一个均匀的正常应力,应力被定义为 应力==负载 P /压力 A, 因此根据载荷的性质应力是可以压缩或拉伸的,并被度量为牛顿每平方米或它的倍数。 如果一个杆受到轴向载荷，即是应力，那么杆的长度会改变。如果杆的初始长度L和改变量△L已知，产生的应力定义如下: 应力==改变长△L /初始长 L 因此应力是一个测量材料变形和无量纲的物理量 ,即它没有单位;它只是两个相同单位的物理量的比值。 一般来说,在实践中,在荷载作用下材料的延伸是非常小的, 测量的应力以*10-6的形式是方便的, 即微应变, 使用的符号也相应成为ue。 从某种意义上说，拉伸应力与应变被认为是正的。压缩应力与应变被认为是负的。因此负应力使长度减小。 当负载移除时，如果材料回复到初始的，无负载时的尺寸时，我们就说它是具有弹性的。一特定形式的适用于大范围的工程材料至少工程材料受载荷的大部分的弹性, 产生正比于负载的变形。由于载荷正比于载荷所产生的压力并且变形正比于应变, 这也说明,当材料是弹性的时候, 应力与应变成正比。因此胡克定律陈述, 应力正比于应变。 这定律服从于大部分铁合金在特定的范围内, 甚至以其合理的准确性可以假定适用于其他工程材料比如混凝土，木材，非铁合金。 当一个材料是弹性的时候，当载荷消除之后，任何负载所产生的变形可以完全恢复,没有永久的变形。

毕设外文翻译

英文翻译 题目: 通过分析变压器中溶解气体而进行故障诊断的专家系统 姓名: 宋日成 学院: 工学院 专业: 自动化 班级: 自动化112 班学号: 32211218 指导教师: 陆静职称: 讲师 2015年3月14日 南京农业大学教务处制

An Expert System for Transformer Fault Diagnosis Using Dissolved Gas Analysis W. S. Chan ·Y. L. Xu ·X. L. Ding ·W. J. Dai Received: 9 November 2005 / Accepted: 11 August 2006 / Published online: 7 September 2006? Springer-Verlag 2006 Abstract In order to automate the transformer fault diagnosis, improve the accuracy of judgment, the introduction of artificial intelligence expert system fault diagnosis. The system is based on fuzzy reasoning confidence by observing the information, the use of knowledge to reach a conclusion. Test proved this method reduces the randomness of judgment, improved diagnosis. Keywords:Expert System Transformer Troubleshooting 1 Introduction The power transformer is a major apparatus in a power system, and its correct functioning is vital to system operations. In order to minimize system outages,many devices have evolved to monitor the serviceability of power transformers. These devices, such as, Buchholz relays or differential relays, respond only to a severe power failure requiring immediate removal of the transformer from service, in which case, outages are inevitable. Thus, preventive techniques for early detection faults to avoid outages would be valuable. In this way, analysis of the mixture of the faulty gases dissolved in insulation oil of power transformer has received worldwide recognition as an effective method for the detection of incipient faults. Many researchers and electrical utilities have reported on their experience and developed interpretative criteria on the basis of DGA. However, criteria tend to vary from utility to utility. Each approach has limitations and none of them has a firm mathematical description. Therefore, transformer diagnosis is still in the heuristic stage. For this reason, knowledge-based programming is a suitable approach to implement in such a diagnostic problem. Based on the interpretation of DGA, a prototype of an expert system for diagnosis of suspected transformer faults and their maintenance procedures is proposed. The significant source in this knowledge base is the gas ratio method. Some limitations of this approach are overcome by incorporating the diagnostic procedure and the synthetic expertise method. Furthermore, data bases adopted from TPCS gas records of transformers are incorporated into the expert system to increase the practical performance. Uncertainty of diagnosis is managed by using fuzzy set concepts. This expert system is constructed with rule based knowledge representation, since it can be expressed by experts. The expert system building tool, Knowledge Engineering System (KES), is used in the development of the knowledge system

机械类毕业设计外文文献翻译

沈阳工业大学工程学院 毕业设计（论文）外文翻译 毕业设计（论文）题目：工具盒盖注塑模具设计 外文题目：Friction , Lubrication of Bearing 译文题目：轴承的摩擦与润滑 系（部）：机械系 专业班级：机械设计制造及其自动化0801 学生姓名：王宝帅 指导教师：魏晓波 2010年10 月15 日

外文文献原文： Friction , Lubrication of Bearing In many of the problem thus far , the student has been asked to disregard or neglect friction . Actually , friction is present to some degree whenever two parts are in contact and move on each other. The term friction refers to the resistance of two or more parts to movement. Friction is harmful or valuable depending upon where it occurs. friction is necessary for fastening devices such as screws and rivets which depend upon friction to hold the fastener and the parts together. Belt drivers, brakes, and tires are additional applications where friction is necessary. The friction of moving parts in a machine is harmful because it reduces the mechanical advantage of the device. The heat produced by friction is lost energy because no work takes place. Also , greater power is required to overcome the increased friction. Heat is destructive in that it causes expansion. Expansion may cause a bearing or sliding surface to fit tighter. If a great enough pressure builds up because made from low temperature materials may melt. There are three types of friction which must be overcome in moving parts: (1)starting, (2)sliding, and(3)rolling. Starting friction is the friction between two solids that tend to resist movement. When two parts are at a state of rest, the surface irregularities of both parts tend to interlock and form a wedging action. To produce motion in these parts, the wedge-shaped peaks and valleys of the stationary surfaces must be made to slide out and over each other. The rougher the two surfaces, the greater is starting friction resulting from their movement . Since there is usually no fixed pattern between the peaks and valleys of two mating parts, the irregularities do not interlock once the parts are in motion but slide over each other. The friction of the two surfaces is known as sliding friction. As shown in figure ,starting friction is always greater than sliding friction . Rolling friction occurs when roller devces are subjected to tremendous stress which cause the parts to change shape or deform. Under these conditions, the material in front of a roller tends to pile up and forces the object to roll slightly uphill. This changing of shape , known as deformation, causes a movement of molecules. As a result ,heat is produced from the added energy required to keep the parts turning and overcome friction. The friction caused by the wedging action of surface irregularities can be overcome