钢结构桥梁中英文对照外文翻译文献
中英文对照外文翻译文献
(文档含英文原文和中文翻译)
Recent Research and Design Developments in Steel and Composite Steel-concrete Structures in USA
The paper will conclude with a look toward the future of structural steel research.
1. Research on steel bridges
The American Association of State Transportation and Highway Officials (AASTHO) is the authority that promulgates design standards for bridges in the US. In 1994 it has issued a new design specification which is a Limit States Design standard that is based on the principles of reliability theory. A great deal of work went into the development of this code in the past decade, especially on calibration and on the probabilistic evaluation of the previous specification. The code is now being implemented in the design office, together with the introduction of the Systeme
Internationale units. Many questions remain open about the new method of design, and there are many new projects that deal with the reliability studies of the bridge as a system. One such current project is a study to develop probabilistic models, load factors, and rational load-combination rules for the combined effects of live-load and wind; live-load and earthquake; live-load, wind and ship collision; and ship collision, wind, and scour. There are also many field measurements of bridge behavior, using modern tools of inspection and monitoring such as acoustic emission techniques and other means of non-destructive evaluation. Such fieldwork necessitates parallel studies in the laboratory, and the evolution of ever more sophisticated high-technology data transmission methods.
America has an aging steel bridge population and many problems arise from fatigue and corrosion. Fatigue studies on full-scale components of the Williamsburg Bridge in New York have recently been completed at Lehigh University. A probabilistic AASTHO bridge evaluation regulation has been in effect since 1989, and it is employed to assess the future useful life of structures using rational methods that include field observation and measurement together with probabilistic analysis. Such an activity also fosters additional research because many issues are still unresolved. One such area is the study of the shakedown of shear connectors in composite bridges. This work has been recently completed at the University of Missouri.
In addition to fatigue and corrosion, the major danger to bridges is the possibility of earthquake induced damage. This also has spawned many research projects on the repair and retrofit of steel superstructures and the supporting concrete piers. Many bridges in the country are being strengthened for earthquake resistance. One area that is receiving much research attention is the strengthening of concrete piers by "jacketing" them by sheets of high-performance reinforced plastic.
The previously described research deals mainly with the behavior of existing structures and the design of new bridges. However, there is also a vigorous activity on novel bridge systems. This research is centered on the application of high-performance steels for the design of innovative plate and box-girder bridges, such as corrugated webs, combinations of open and closed shapes, and longer spans
for truss bridges. It should be mentioned here that, in addition to work on steel bridges, there is also very active research going on in the study of the behavior of prestressed concrete girders made from very high strength concrete. The performance and design of smaller bridges using pultruded high-performance plastic composite members is also being studied extensively at present. New continuous bridge systems with steel concrete composite segments in both the positive moment and the negative moment regions are being considered. Several researchers have developed strong capabilities to model the three-dimensional non-linear behavior of individual plate girders, and many studies are being performed on the buckling and post-buckling characteristics of such https://www.wendangku.net/doc/9b5193853.html,panion experimental studies are also made,especially on members built from high-performance steels. A full-scale bridge of such steel has been designed, and will soon be constructed and then tested under traffic loading. Research efforts are also underway on the study of the fatigue of large expansion joint elements and on the fatigue of highway sign structures.
The final subject to be mentioned is the resurgence of studies of composite steel concrete horizontally curved steel girder bridges. A just completed project at the University of Minnesota monitored the stresses and the deflections in a skewed and curved bridge during all phases of construction, starting from the fabrication yard to the completed bridge.~ Excellent correlation was found to exist between the measured stresses and deformations and the calculated values. The stresses and deflections during construction were found to be relatively small, that is, the construction process did not cause severe trauma to the system. The bridge has now been tested under service loading, using fully loaded gravel trucks, for two years, and it will continue to be studied for further years to measure changes in performance under service over time. A major testing project is being conducted at the Federal Highway Administration laboratory in Washington, DC, where a half-scale curved composite girder bridge is currently being tested to determine its limit states. The test-bridge was designed to act as its own test-frame, where various portions can be replaced after testing. Multiple flexure tests, shear tests, and tests under combined bending and shear, are thus performed with realistic end-conditions and restraints. The experiments are
also modeled by finite element analysis to check conformance between reality and prediction. Finally design standards will be evolved from the knowledge gained. This last project is the largest bridge research project in the USA at the present time.
From the discussion above it can be seen that even though there is no large expansion of the nation's highway and railroad system, there is extensive work going on in bridge research. The major challenge facing both the researcher and the transportation engineer is the maintenance of a healthy but aging system, seeing to its gradual replacement while keeping it safe and serviceable.
2. Research on steel members and frames
There are many research studies on the strength and behavior of steel building structures. The most important of these have to do with the behavior and design of steel structures under severe seismic events. This topic will be discussed later in this paper. The most significant trends of the non-seismic research are the following: "Advanced" methods of structural analysis and design are actively studied at many Universities, notably at Cornell, Purdue, Stanford, and Georgia Tech Universities. Such analysis methods are meant to determine the load-deformation behavior of frames up to and beyond failure, including inelastic behavior, force redistribution, plastic hinge formation, second-order effects and frame instability. When these methods are fully operational, the structure will not have to undergo a member check, because the finite element analysis of the frame automatically performs this job. In addition to the research on the best approaches to do this advanced analysis, there are also many studies on simplifications that can be easily utilized in the design office while still maintaining the advantages of a more complex analysis. The advanced analysis method is well developed for in-plane behavior, but much work is yet to be done on the cases where bi-axial bending or lateraltorsional buckling must be considered. Some successes have been achieved, but the research is far from complete.
Another aspect of the frame behavior work is the study of the frames with semirigid joints. The American Institute of Steel Construction (AISC) has published design methods for office use. Current research is concentrating on the behavior of
such structures under seismic loading. It appears that it is possible to use such frames in some seismic situations, that is, frames under about 8 to 10 stories in height under moderate earthquake loads. The future of structures with semi-rigid frames looks very promising, mainly because of the efforts of researchers such as Leon at Georgia Tech University, and many others.
Research on member behavior is concerned with studying the buckling and post buckling behavior of compact angle and wide-flange beam members by advanced commercial finite element programs. Such research is going back to examine the assumptions made in the 1950s and 1960s when the plastic design compactness and bracing requirements were first formulated on a semi-empirical basis. The non-linear finite element computations permit the "re-testing" of the old experiments and the performing of new computer experiments to study new types of members and new types of steels. White of Georgia Tech is one of the pioneers in this work. Some current research at the US military Academy and at the University of Minnesota by Earls is discussed later in this report. The significance of this type of research is that the phenomena of extreme yielding and distortion can be efficiently examined in parameter studies performed on the computer. The computer results can be verified with old experiments, or a small number of new experiments. These studies show a good prospect fornew insights into old problems that heretofore were never fully solved.
3. Research on cold-formed steel structures
Next to seismic work, the most active part of research in the US is on cold-formed steel structures. The reason for this is that the supporting industry is expanding, especially in the area of individual family dwellings. As the cost of wood goes up, steel framed houses become more and more economical. The intellectual problems of thin-walled structures buckling in multiple modes under very large deformations have attracted some of the best minds in stability research. As a consequence, many new problems have been solved: complex member stiffening systems, stability and bracing of C and Z beams, composite slabs, perforated columns, standing-seam roof systems, bracing and stability of beams with very complicated
shapes, cold-formed members with steels of high yield stress-to-tensile strength ratio, and many other interesting applications. The American Iron and Steel Institute (AISI) has issued a new expanded standard in 1996 that brought many of these research results into the hands of the designer.
4. Research on steel-concrete composite structures
Almost all structural steel bridges and buildings in the US are built with composite beams or girders. In contrast, very few columns are built as composite members. The area of composite Column research is very active presently to fill up the gap of technical information on the behavior of such members. The subject of steel tubes filled with high-strength concrete is especially active. One of the aims of research performed by Hajjar at the University of Minnesota is to develop a fundamental understanding of the various interacting phenomena that occur in concrete-filled columns and beam-columns under monotonic and cyclic load. The other aim is to obtain a basic understanding of the behavior of connections of wide-flange beams to concrete filled tubes.
Other major research work concerns the behavior and design of built-up composite wide-flange bridge girders under both positive and negative bending. This work is performed by Frank at the University of Texas at Austin and by White of Georgia Tech, and it involves extensive studies of the buckling and post-buckling of thin stiffened webs. Already mentioned is the examination of the shakedown of composite bridges. The question to be answered is whether a composite bridge girder loses composite action under repeated cycles of loads which are greater than the elastic limit load and less than the plastic mechanism load. A new study has been initiated at the University of Minnesota on the interaction between a semi-rigid steel frame system and a concrete shear wall connected by stud shear connectors.
5. Research on connections
Connection research continues to interest researchers because of the great variety of joint types. The majority of the connection work is currently related to the seismic problems that will be discussed in the next section of this paper. The most interest in non-seismic connections is the characterization of the monotonic moment-rotation
behavior of various types of semi-rigid joints.
6. Research on structures and connections subject to seismic forces
The most compelling driving force for the present structural steel research effort in the US was the January 17, 1994 earthquake in Northridge, California, North of Los Angeles. The major problem for steel structures was the extensive failure of prequalified welded rigid joints by brittle fracture. In over 150 buildings of one to 26 stories high there were over a thousand fractured joints. The buildings did not collapse, nor did they show any external signs of distress, and there were no human injuries or deaths. A typical joint is shown in Fig. 2.2.1.
In this connection the flanges of the beams are welded to the flanges of the column by full-penetration butt welds. The webs are bolted to the beams and welded to the columns. The characteristic features of this type of connection are the backing bars at the bottom of the beam flange, and the cope-holes left open to facilitate the field welding of the beam flanges. Fractures occurred in the welds, in the beam flanges, and/or in the column flanges, sometimes penetrating into the webs.
Once the problem was discovered several large research projects were initiated at various university laboratories, such as The University of California at San Diego, the University of Washington in Seattle, the University of Texas at Austin, Lehigh University at Bethlehem, Pennsylvania, and at other places. The US Government under the leadership of the Federal Emergency Management Agency (FEMA) instituted a major national research effort. The needed work was deemed so extensive
that no single research agency could hope to cope with it. Consequently three California groups formed a consortium which manages the work:
(1) Structural Engineering Association of California.
(2) Applied Technology Council.
(3) California Universities for Research in Earthquake Engineering.
The first letters in the name of each agency were combined to form the acronym SAC, which is the name of the joint venture that manages the research. We shall read much from this agency as the results of the massive amounts of research performed under its aegis are being published in the next few years.
The goals of the program are to develop reliable, practical and cost-effective guidelines for the identification and inspection of at-risk steel moment frame buildings, the repair or upgrading of damaged buildings, the design of new construction, and the rehabilitation of undamaged buildings.~ As can be seen, the scope far exceeds the narrow look at the connections only. The first phase of the research was completed at the end of 1996, and its main aim was to arrive at interim guidelines so that design work could proceed. It consisted of the following components:
~ A state-of-the-art assessment of knowledge on steel connections.
~ A survey of building damage.
~ The evaluation of ground motion.
~ Detailed building analyses and case studies.
~ A preliminary experimental program.
~ Professional training and quality assurance programs.
~ Publishing of the Interim Design Guidelines.
A number of reports were issued in this first phase of the work. A partial list of these is appended at the end of this paper.
During the first phase of the SAC project a series of full-scale connection tests under static and, occasionally, dynamic cyclic tests were performed. Tests were of pre-Northridge-type connections (that is, connections as they existed at the time of the earthquake), of repaired and upgraded details, and of new recommended
connection details. A schematic view of the testing program is illustrated in Fig.
2.2.2 Some recommended strategies for new design are schematically shown in Fig. 2.2.
3.
Fig. 2.2.3 some recommended improvements in the interim guidelines
The following possible causes, and their combinations, were found to have contributed to tile connection failures:
~ Inadequate workmanship in the field welds.
~ Insufficient notch-toughness of the weld metal.
~ Stress raisers caused by the backing bars.
~ Lack of complete fusion near the backing bar.
~ Weld bead sizes were too big.
~ Slag inclusion in the welds.
While many of the failures can be directly attributed to the welding and the
material of the joints, there are more serious questions relative to the structural system that had evolved over the years mainly based on economic considerations.' The structural system used relatively few rigid-frames of heavy members that were designed to absorb the seismic forces for large parts of the structure. These few lateral-force resistant frames provide insufficient redundancy. More rigid-frames with smaller members could have provided a tougher and more ductile structural system. There is a question of size effect: Test results from joints of smaller members were extrapolated to joints with larger members without adequate test verification. The effect of a large initial pulse may have triggered dynamic forces that could have caused brittle fracture in joints with fracture critical details and materials. Furthermore, the yield stress of the beams was about 30% to 40% larger than the minimum specified values assumed in design, and so the connection failed before the beams, which were supposed to form plastic hinges.
As can be seen, there are many possible reasons for this massive failure rate, and there is blame to go around for everyone. No doubt, the discussion about why and how the joints failed will go on for many more years. The structural system just did not measure up to demands that were more severe than expected. What should be kept in mind, however, is that no structure collapsed or caused even superficial nonstructural damage, and no person was injured or killed. In the strictest sense the structure sacrificed itself so that no physical harm was done to its users. The economic harm, of course, was enormous.
7. Future directions of structural steel research and conclusion
The future holds many challenges for structural steel research. The ongoing work necessitated by the two recent earthquakes that most affected conventional design methods, namely, the Northridge earthquake in the US and the Kobe earthquake in Japan, will continue well into the first decade of the next Century. It is very likely that future disasters of this type will bring yet other problems to the steel research community. There is a profound change in the philosophy of design for disasters: We can no longer be content with saving lives only, but we must also design structures which will not be so damaged as to require extensive repairs.
桥梁工程毕业设计外文翻译箱梁
桥梁工程毕业设计外文翻译箱梁
西南交通大学本科毕业设计（论文） 外文资料翻译 年级: 学号: 姓名: 专业: 指导老师:
6 月
外文资料原文： 13 Box girders 13.1 General The box girder is the most ?exible bridge deck form. It can cover a range of spans from25 m up to the largest non-suspended concrete decks built, of the order of 300 m. Single box girders may also carry decks up to 30 m wide. For the longer span beams, beyond about 50 m, they are practically the only feasible deck section. For the shorter spans they are in competition with most of the other deck types discussed in this book. The advantages of the box form are principally its high structural ef?ciency (5.4), which minimises the prestress force required to resist a given bending moment, and its great torsional strength with the capacity this gives to re-centre eccentric live loads, minimising the prestress required to carry them.
中英文参考文献格式
中文参考文献格式 参考文献（即引文出处）的类型以单字母方式标识： M——专著，C——论文集，N——报纸文章，J——期刊文章，D——学位论文，R——报告，S——标准，P——专利；对于不属于上述的文献类型，采用字母“Z”标识。 参考文献一律置于文末。其格式为： （一）专著 示例 [1] 张志建.严复思想研究[M]. 桂林：广西师范大学出版社，1989. [2] 马克思恩格斯全集：第1卷[M]. 北京：人民出版社，1956. [3] [英]蔼理士.性心理学[M]. 潘光旦译注.北京：商务印书馆，1997. （二）论文集 示例 [1] 伍蠡甫.西方文论选[C]. 上海：上海译文出版社，1979. [2] 别林斯基.论俄国中篇小说和果戈里君的中篇小说[A]. 伍蠡甫.西方文论选：下册[C]. 上海：上海译文出版社，1979. 凡引专著的页码，加圆括号置于文中序号之后。 （三）报纸文章 示例 [1] 李大伦.经济全球化的重要性[N]. 光明日报，1998-12-27，（3） （四）期刊文章 示例 [1] 郭英德.元明文学史观散论[J]. 北京师范大学学报（社会科学版），1995（3）. （五）学位论文 示例 [1] 刘伟.汉字不同视觉识别方式的理论和实证研究[D]. 北京：北京师范大学心理系，1998. （六）报告 示例 [1] 白秀水，刘敢，任保平. 西安金融、人才、技术三大要素市场培育与发展研究[R]. 西安：陕西师范大学西北经济发展研究中心，1998. （七）、对论文正文中某一特定内容的进一步解释或补充说明性的注释，置于本页地脚，前面用圈码标识。 参考文献的类型 根据GB3469-83《文献类型与文献载体代码》规定，以单字母标识： M——专著（含古籍中的史、志论著） C——论文集 N——报纸文章 J——期刊文章 D——学位论文 R——研究报告 S——标准 P——专利 A——专著、论文集中的析出文献 Z——其他未说明的文献类型 电子文献类型以双字母作为标识： DB——数据库 CP——计算机程序 EB——电子公告
中英文论文对照格式
英文论文APA格式 英文论文一些格式要求与国内期刊有所不同。从学术的角度讲，它更加严谨和科学，并且方便电子系统检索和存档。 版面格式
表格 表格的题目格式与正文相同，靠左边，位于表格的上部。题目前加Table后跟数字，表示此文的第几个表格。 表格主体居中，边框粗细采用0.5磅；表格内文字采用Times New Roman，10磅。 举例： Table 1. The capitals, assets and revenue in listed banks
图表和图片 图表和图片的题目格式与正文相同，位于图表和图片的下部。题目前加Figure 后跟数字，表示此文的第几个图表。图表及题目都居中。只允许使用黑白图片和表格。 举例： Figure 1. The Trend of Economic Development 注：Figure与Table都不要缩写。 引用格式与参考文献 1. 在论文中的引用采取插入作者、年份和页数方式，如"Doe (2001, p.10) reported that …" or "This在论文中的引用采取作者和年份插入方式，如"Doe (2001, p.10) reported that …" or "This problem has been studied previously (Smith, 1958, pp.20-25)。文中插入的引用应该与文末参考文献相对应。 举例：Frankly speaking, it is just a simulating one made by the government, or a fake competition, directly speaking. (Gao, 2003, p.220). 2. 在文末参考文献中，姓前名后，姓与名之间以逗号分隔；如有两个作者，以and连接；如有三个或三个以上作者，前面的作者以逗号分隔，最后一个作者以and连接。 3. 参考文献中各项目以“点”分隔，最后以“点”结束。 4. 文末参考文献请按照以下格式：
桥梁专业外文翻译--欧洲桥梁研究
桥梁专业外文翻译--欧洲桥梁研究
附录 Bridge research in Europe A brief outline is given of the development of the European Union, together with the research platform in Europe. The special case of post-tensioned bridges in the UK is discussed. In order to illustrate the type of European research being undertaken, an example is given from the University of Edinburgh portfolio: relating to the identification of voids in post-tensioned concrete bridges using digital impulse radar. Introduction The challenge in any research arena is to harness the findings of different research groups to identify a coherent mass of data, which enables research and practice to be better focused. A particular challenge exists with respect to Europe where language barriers are inevitably very significant. The European Community was formed in the 1960s based upon a political will within continental Europe to avoid the European civil wars, which developed into World War 2 from 1939 to 1945. The strong political motivation formed the original community of which Britain was not a member. Many of the continental countries saw Britain’s interest as being purely economic. The 1970s saw Britain joining what was then the European Economic Community (EEC) and the 1990s has seen the widening of the community to a European Union, EU, with certain political goals together with the objective of a common European currency. Notwithstanding these financial and political developments, civil engineering and bridge engineering in particular have found great difficulty in forming any kind of common thread. Indeed the educational systems for University training are quite different between Britain and the European continental countries. The formation of the EU funding schemes —e.g. Socrates, Brite Euram and other programs have helped significantly. The Socrates scheme is based upon the exchange of students between Universities in different member states. The Brite Euram scheme has involved technical research grants given to
机械毕业设计英文外文翻译399驱动桥
附录A 英文文献 Drive Axle All vehicles have some type of drive axle/differential assembly incorporated into the driveline. Whether it is front, rear or four wheel drive, differentials are necessary for the smooth application of engine power to the road. Powerflow The drive axle must transmit power through a 90°angle. The flow of power in conventional front engine/rear wheel drive vehicles moves from the engine to the drive axle in approximately a straight line. However, at the drive axle, the power must be turned at right angles (from the line of the driveshaft) and directed to the drive wheels. This is accomplished by a pinion drive gear, which turns a circular ring gear. The ring gear is attached to a differential housing, containing a set of smaller gears that are splined to the inner end of each axle shaft. As the housing is rotated, the internal differential gears turn the axle shafts, which are also attached to the drive wheels. Rear-wheel drive Rear-wheel-drive vehicles are mostly trucks, very large sedans and many sports car and coupe models. The typical rear wheel drive vehicle uses a front mounted engine and transmission assemblies with a driveshaft coupling the transmission to the rear drive axle. Drive in through the layout of the bridge, the bridge drive shaft arranged vertically in the same vertical plane, and not the drive axle shaft, respectively, in their own sub-actuator with a direct connection, but the actuator is located at the front or the back of the adjacent shaft
中英文论文参考文献标准格式 超详细
超详细中英文论文参考文献标准格式 1、参考文献和注释。按论文中所引用文献或注释编号的顺序列在论文正文之后，参考文献之前。图表或数据必须注明来源和出处。 （参考文献是期刊时，书写格式为： [编号]、作者、文章题目、期刊名（外文可缩写）、年份、卷号、期数、页码。参考文献是图书时，书写格式为： [编号]、作者、书名、出版单位、年份、版次、页码。） 2、附录。包括放在正文内过份冗长的公式推导，以备他人阅读方便所需的辅助性数学工具、重复性数据图表、论文使用的符号意义、单位缩写、程序全文及有关说明等。 参考文献（即引文出处）的类型以单字母方式标识，具体如下： [M]--专著,著作 [C]--论文集(一般指会议发表的论文续集，及一些专题论文集，如《***大学研究生学术论文集》[N]-- 报纸文章 [J]--期刊文章：发表在期刊上的论文，尽管有时我们看到的是从网上下载的（如知网），但它也是发表在期刊上的，你看到的电子期刊仅是其电子版 [D]--学位论文：不区分硕士还是博士论文 [R]--报告：一般在标题中会有"关于****的报告"字样 [S]-- 标准 [P]--专利 [A]--文章：很少用，主要是不属于以上类型的文章 [Z]--对于不属于上述的文献类型，可用字母"Z"标识，但这种情况非常少见 常用的电子文献及载体类型标识： [DB/OL] --联机网上数据(database online) [DB/MT] --磁带数据库(database on magnetic tape) [M/CD] --光盘图书(monograph on CDROM) [CP/DK] --磁盘软件(computer program on disk) [J/OL] --网上期刊(serial online) [EB/OL] --网上电子公告(electronic bulletin board online) 很显然，标识的就是该资源的英文缩写，/前面表示类型，/后面表示资源的载体，如OL表示在线资源 二、参考文献的格式及举例 1．期刊类 【格式】[序号]作者.篇名[J].刊名,出版年份,卷号(期号)起止页码. 【举例】 [1] 周融，任志国，杨尚雷，厉星星.对新形势下毕业设计管理工作的思考与实践[J].电气电子教学学报，2003(6):107-109. [2] 夏鲁惠.高等学校毕业设计(论文)教学情况调研报告[J].高等理科教育,2004(1):46-52. [3] Heider, E.R.& D.C.Oliver. The structure of color space in naming and memory of two languages [J]. Foreign Language Teaching and Research, 1999, (3): 62 67. 2．专著类
建设部文献中英文对照
贯彻落实科学发展观大力发展节能与绿色建筑 （2005年2月23日） 中华人民共和国建设部 节能建筑是按节能设计标准进行设计和建造、使其在使用过程中降低能耗的建筑。 绿色建筑是指为人们提供健康、舒适、安全的居住、工作和活动的空间，同时在建筑全生命周期（物料生产，建筑规划、设计、施工、运营维护及拆除过程）中实现高效率地利用资源（能源、土地、水资源、材料）、最低限度地影响环境的建筑物。绿色建筑也有人称之为生态建筑、可持续建筑。 一、发展节能与绿色建筑的重要意义 建筑作为人工环境，是满足人类物质和精神生活需要的重要组成部分。然而，人类对感官享受的过度追求，以及不加节制的开发与建设，使现代建筑不仅疏离了人与自然的天然联系和交流，也给环境和资源带来了沉重的负担。据统计，人类从自然界所获得的50％以上的物质原料用来建造各类建筑及其附属设施，这些建筑在建造与使用过程中又消耗了全球能源的50％左右；在环境总体污染中，与建筑有关的空气污染、光污染、电磁污染等就占了34％；建筑垃圾则占人类活动产生垃圾总量的40％；在发展中国家，剧增的建筑量还造成侵占土地、破坏生态环境等现象日益严重。中国正处于工业化和城镇化快速发展阶段，要在未来15年保持GDP年均增长7％以上，将面临巨大的资源约束瓶颈和环境恶化压力。严峻的事实告诉我们，中国要走可持续发展道路，发展节能与绿色建筑刻不容缓。 绿色建筑通过科学的整体设计，集成绿色配置、自然通风、自然采光、低能耗围护结构、新能源利用、中水回用、绿色建材和智能控制等高新技术，具有选址规划合理、资源利用高效循环、节能措施综合有效、建筑环境健康舒适、废物排放减量无害、建筑功能灵活适宜等六大特点。它不仅可以满足人们的生理和心理需求，而且能源和资源的消耗最为经济合理，对环境的影响最小。 胡锦涛同志指出：要大力发展节能省地型住宅，全面推广节能技术，制定并强制执行节能、节材、节水标准，按照减量化、再利用、资源化的原则，搞好资源综合利用，实现经济社会的可持续发展。温家宝和曾培炎同志也多次指出，建筑节能不仅是经济问题，而且是重要的战略问题。 发展节能与绿色建筑是建设领域贯彻“三个代表”重要思想和十六大精神，认真落实以人为本，全面、协调、可持续的科学发展观，统筹经济社会发展、人与
本科毕业设计桥梁外文翻译
附录一：中文翻译 土木工程师 桥梁工程156 2003年3月发表于BEI 31~37页 2002年1月31日收到 C.詹姆斯 2002年12月9日通过高级土木工程师佩尔 Frischmann ，埃克塞特 关键词：桥梁；河堤；土工布；膜与土工格栅 英国锁城大桥 锁城大桥是横跨住宅发展区的铁路桥梁。由于工程施工受到周围建筑与地形的限制，该工程采取加固桥台、桥墩与桥面的刚构结构，以及预制栏杆等方法提高了大桥的使用安全程度，并降低了大桥建造与维护的费用。因此，城堡大桥科学的设计方案使工程成本降到最低。 一、引言 本文描述的是在受限制地区用最小的费用修建一座铁路桥梁使之成为开放的住宅发展区。锁城地区是位于住宅发展十分紧张的韦斯顿超 图1 锁城大桥位置远景
马雷的东部。监督桥梁建设的客户是城堡建设有限公司，它由二大房建者组成。该区的规划局是北盛捷区议会（NSDC）。该发展地区被分为布里斯托尔和埃克塞特。规划条件规定，直到建成这条横跨的铁路大桥为止，该地区南部区域不可能适应居住。可见锁城大桥的建成对该地区发展的重要性。 发展地区位于萨默塞特的边缘，这个地区地形十分的恶劣，该范围位于韦斯顿以北和A321飞机双程双线分隔线的南面。现在只有一条乡下公路，是南部区域的唯一通道。该地区是交通预期不适合住宅增加的区域。 由于盛捷地区水平高程的限制，新的铁路线在桥台两边必须设有高程差。并且该地区地形限制，允许正常横跨的区域较小，这导致在结构的布局上的一定数量的妥协。为了整个城堡地区的发展，全 图2 锁城大桥地图上位置 桥限速20公里/时，并考虑区域范围内的速度制约。这样在得到客户和NSDC的同意后，桥梁采取了最小半径的方法，这使得桥梁采用了比正常梯度更加陡峭地方法实现高程的跨越。 客户的工程师、工程顾问、一般设计原则和初步认同原则下(AIP)与NSDC发出投标文件。 该合同在2000年7月1授予安迪。投标价值1.31亿美元，合同期定为34周，到2001年4月完成。
中英文参考文献格式
中英文参考文献格式! (細節也很重要啊。。）来源：李菲玥的日志 规范的参考文献格式 一、参考文献的类型 参考文献（即引文出处）的类型以单字母方式标识，具体如下： M——专著C——论文集N——报纸文章J——期刊文章 D——学位论文R——报告S——标准P——专利 A——文章 对于不属于上述的文献类型，采用字母“Z”标识。 常用的电子文献及载体类型标识： ［ＤＢ/OL］——联机网上数据(database online) ［DB/MT］——磁带数据库(database on magnetic tape) ［Ｍ/CD］——光盘图书(monograph on CD ROM) ［ＣＰ／DK］——磁盘软件(computer program on disk) ［Ｊ／ＯＬ］——网上期刊(serial online) ［ＥＢ/OL］——网上电子公告(electronic bulletin board online) 对于英文参考文献，还应注意以下两点： ①作者姓名采用“姓在前名在后”原则，具体格式是：姓，名字的首字母. 如：Malcolm R ichard Cowley 应为：Cowley, M.R.，如果有两位作者，第一位作者方式不变，&之后第二位作者名字的首字母放在前面，姓放在后面，如：Frank Norris 与Irving Gordon应为：Norri s, F. & I.Gordon.； ②书名、报刊名使用斜体字，如：Mastering English Literature，English Weekly。二、参考文献的格式及举例 1．期刊类 【格式】[序号]作者.篇名[J].刊名，出版年份，卷号（期号）：起止页码. 【举例】 [1] 周融，任志国，杨尚雷，厉星星.对新形势下毕业设计管理工作的思考与实践[J].电气电子教学学报，2003(6)：107-109.
医学文献中英文对照
动脉粥样硬化所导致的心脑血管疾病是目前发病率和死亡率较高的疾病之一。在动脉粥样硬化的形成过程中, 内皮细胞病变是其中极其重要的因素，最显著的变化是动脉内皮功能紊乱, 血管内皮细胞的损伤和功能改变是动脉粥样硬化发生的起始阶段。 Cardiovascular and cerebrovascular disease caused by atherosclerosis is one of diseases with higher mortality and morbidity at present . In the formation of atherosclerosis, the endothelial cell lesion is one of the most important factors, in which, the most significant change is endothelial dysfunction. In addition, the injuries and the changes of vascular endothelial cells are the initial factors of atherosclerosis. 许多因素会导致血管内皮细胞受损, 主要包括脂多糖(Lipopolysaccharides , LPS)、炎症介质、氧自由基等。其中脂多糖因其广泛的生物学作用, 越来越引起研究者的关注。LPS 是一种炎症刺激物, 是革兰阴性杆菌细胞壁的主要组成成分，其通过刺激血管内皮细胞，引起其相关细胞因子和炎性因子的表达紊乱，尤其是Ca2+ 和活性氧簇(Reactive Oxygen Species , ROS的合成和释放发生改变诱导细胞氧化应激内环境紊乱。大量研究表明, LPS 直接参与动脉粥样硬化的形成过程, 特别是动脉粥样硬化血管炎症的初始阶段, LPS可通过直接作用或间接影响的方式激活并损伤内皮细胞，从而引 起血管内皮细胞形态与功能的改变。 Many factors induce vascular endothelial cell damage, including lipopolysaccharides (LPS), inflammatory mediators and oxygen free
桥梁专业外文翻译--欧洲桥梁研究
中文1850字 附录 Bridge research in Europe A brief outline is given of the development of the European Union, together with the research platform in Europe. The special case of post-tensioned bridges in the UK is discussed. In order to illustrate the type of European research being undertaken, an example is given from the University of Edinburgh portfolio: relating to the identification of voids in post-tensioned concrete bridges using digital impulse radar. Introduction The challenge in any research arena is to harness the findings of different research groups to identify a coherent mass of data, which enables research and practice to be better focused. A particular challenge exists with respect to Europe where language barriers are inevitably very significant. The European Community was formed in the 1960s based upon a political will within continental Europe to avoid the European civil wars, which developed into World War 2 from 1939 to 1945. The strong political motivation formed the original community of which Britain was not a member. Many of the continental countries saw Britain’s interest as being purely economic. The 1970s saw Britain joining what was then the European Economic Community (EEC) and the 1990s has seen the widening of the community to a European Union, EU, with certain political goals together with the objective of a common European currency. Notwithstanding these financial and political developments, civil engineering and bridge engineering in particular have found great difficulty in forming any kind of common thread. Indeed the educational systems for University training are quite different between Britain and the European continental countries. The formation of the EU funding schemes —e.g. Socrates, Brite Euram and other programs have helped significantly. The Socrates scheme is based upon the exchange of students between Universities in different member states. The Brite Euram scheme has involved technical research grants given to consortia of academics and industrial
桥梁外文翻译
毕业设计/论文 外文文献翻译 院系城市建设学院 专业班级 姓名 原文出处 评分 指导教师 华中科技大学武昌分校 20 12 年3月1日
Study on nonlinear analysis of a redundant cable-stayed bridge 1．Abstract A comparison on nonlinear analysis of a highly redundant cable-stayed bridge is performed in the study. The initial shapes including geometry and prestress distribution of the bridge are determined by using a two-loop iteration method, it is an equilibrium iteration loop and a shape iteration loop. For the initial shape analysis a linear and a nonlinear computation procedure are set up. In the former all nonlinearities of cable-stayed bridges are disregarded, and the shape iteration is carried out without considering equilibrium. In the latter all nonlinearities of the bridges are taken into consideration and both the equilibrium and the shape iteration are carried out. Based on the convergent initial shapes determined by the different procedures, the natural frequencies and vibration modes are then examined in details. Numerical results show that a convergent initial shape can be found rapidly by the two-loop iteration method, a reasonable initial shape can be determined by using the linear computation procedure, and a lot of computation efforts can thus be saved. There are only small differences in geometry and prestress distribution between the results determined by linear and nonlinear computation procedures. However, for the analysis of natural frequency and vibration modes, significant differences in the fundamental frequencies and vibration modes will occur, and the nonlinearities of the cable-stayed bridge response appear only in the modes determined on basis of the initial shape found by the nonlinear computation. 2. Introduction Rapid progress in the analysis and construction of cable-stayed bridges has been made over the last three decades. The progress is mainly due to developments in the fields of computer technology, high strength steel cables, orthotropic steel decks and construction technology. Since the first modern cable-stayed bridge was built in Sweden in 1955, their popularity has rapidly been increasing all over the world. Because of its aesthetic appeal, economic grounds and ease of erection, the
英文引用及参考文献格式要求
英文引用及参考文献格式要求 一、参考文献的类型 参考文献（即引文出处）的类型以单字母方式标识，具体如下： M——专著C——论文集N——报纸文章 J——期刊文章D——学位论文R——报告 对于不属于上述的文献类型，采用字母“Z”标识。 对于英文参考文献，还应注意以下两点： ①作者姓名采用“姓在前名在后”原则，具体格式是：姓，名字的首字母.如：MalcolmRichardCowley应为：Cowley,M.R.，如果有两位作者，第一位作者方式不变，&之后第二位作者名字的首字母放在前面，姓放在后面，如：FrankNorris与IrvingGordon应为：Norris,F.&I.Gordon.； ②书名、报刊名使用斜体字，如：MasteringEnglishLiterature，EnglishWeekly。 二、参考文献的格式及举例 1.期刊类 【格式】[序号]作者.篇名[J].刊名，出版年份，卷号（期号）：起止页码. 【举例】 [1]王海粟.浅议会计信息披露模式[J].财政研究，2004,21(1)：56-58. [2]夏鲁惠.高等学校毕业论文教学情况调研报告[J].高等理科教育，2004(1):46-52. [3]Heider,E.R.&D.C.Oliver.Thestructureofcolorspaceinnamingandmemo ryoftwolanguages[J].ForeignLanguageTeachingandResearch,1999,(3):62–6 7. 2.专著类 【格式】[序号]作者.书名[M].出版地：出版社，出版年份：起止页码. 【举例】[4]葛家澍，林志军.现代西方财务会计理论[M].厦门：厦门大学出版社，2001：42. [5]Gill,R.MasteringEnglishLiterature[M].London:Macmillan,1985:42-45. 3.报纸类 【格式】[序号]作者.篇名[N].报纸名，出版日期（版次）. 【举例】 [6]李大伦.经济全球化的重要性[N].光明日报，1998-12-27(3). [7]French,W.BetweenSilences:AVoicefromChina[N].AtlanticWeekly,198 715(33). 4.论文集 【格式】[序号]作者.篇名[C].出版地：出版者，出版年份：起始页码. 【举例】 [8]伍蠡甫.西方文论选[C].上海：上海译文出版社，1979：12-17. [9]Spivak,G.“CantheSubalternSpeak?”[A].InC.Nelson&L.Grossberg(e ds.).VictoryinLimbo:Imigism[C].Urbana:UniversityofIllinoisPress,1988, pp.271-313.
平面设计中英文对照外文翻译文献
(文档含英文原文和中文翻译) 中英文翻译 平面设计 任何时期平面设计可以参照一些艺术和专业学科侧重于视觉传达和介绍。采用多种方式相结合，创造和符号，图像和语句创建一个代表性的想法和信息。平面设计师可以使用印刷，视觉艺术和排版技术产生的最终结果。平面设计常常提到的进程，其中沟通是创造和产品设计。 共同使用的平面设计包括杂志，广告，产品包装和网页设计。例如，可能包括产品包装的标志或其他艺术作品，举办文字和纯粹的设计元素，如形状和颜色统一件。组成的一个最重要的特点，尤其是平面设计在使用前现有材料或不同的元素。 平面设计涵盖了人类历史上诸多领域，在此漫长的历史和在相对最近爆炸视觉传达中的第20和21世纪，人们有时是模糊的区别和重叠的广告艺术，平面设计和美术。毕竟，他们有着许多相同的内容，理论，原则，做法和语言，有时同样的客人或客户。广告艺术的最终目标是出售的商品和服务。在平面
设计，“其实质是使以信息，形成以思想，言论和感觉的经验”。 在唐朝（ 618-906 ）之间的第4和第7世纪的木块被切断打印纺织品和后重现佛典。阿藏印在868是已知最早的印刷书籍。 在19世纪后期欧洲，尤其是在英国，平面设计开始以独立的运动从美术中分离出来。蒙德里安称为父亲的图形设计。他是一个很好的艺术家，但是他在现代广告中利用现代电网系统在广告、印刷和网络布局网格。 于1849年，在大不列颠亨利科尔成为的主要力量之一在设计教育界，该国政府通告设计在杂志设计和制造的重要性。他组织了大型的展览作为庆祝现代工业技术和维多利亚式的设计。 从1892年至1896年威廉?莫里斯凯尔姆斯科特出版社出版的书籍的一些最重要的平面设计产品和工艺美术运动，并提出了一个非常赚钱的商机就是出版伟大文本论的图书并以高价出售给富人。莫里斯证明了市场的存在使平面设计在他们自己拥有的权利，并帮助开拓者从生产和美术分离设计。这历史相对论是，然而，重要的，因为它为第一次重大的反应对于十九世纪的陈旧的平面设计。莫里斯的工作，以及与其他私营新闻运动，直接影响新艺术风格和间接负责20世纪初非专业性平面设计的事态发展。 谁创造了最初的“平面设计”似乎存在争议。这被归因于英国的设计师和大学教授Richard Guyatt，但另一消息来源于20世纪初美国图书设计师William Addison Dwiggins。 伦敦地铁的标志设计是爱德华约翰斯顿于1916年设计的一个经典的现代而且使用了系统字体设计。 在20世纪20年代，苏联的建构主义应用于“智能生产”在不同领域的生产。个性化的运动艺术在俄罗斯大革命是没有价值的，从而走向以创造物体的功利为目的。他们设计的建筑、剧院集、海报、面料、服装、家具、徽标、菜单等。 Jan Tschichold 在他的1928年书中编纂了新的现代印刷原则，他后来否认他在这本书的法西斯主义哲学主张，但它仍然是非常有影响力。 Tschichold ，包豪斯印刷专家如赫伯特拜耳和拉斯洛莫霍伊一纳吉，和El Lissitzky 是平面设计之父都被我们今天所知。 他们首创的生产技术和文体设备，主要用于整个二十世纪。随后的几年看到平面设计在现代风格获得广泛的接受和应用。第二次世界大战结束后，美国经济的建立更需要平面设计，主要是广告和包装等。移居国外的德国包豪斯设计学院于1937年到芝加哥带来了“大规模生产”极简到美国;引发野火的“现代”建筑和设计。值得注意的名称世纪中叶现代设计包括阿德里安Frutiger ，设计师和Frutiger字体大学;保兰德，从20世纪30年代后期，直到他去世于1996年，采取的原则和适用包豪斯他们受欢迎的广告和标志设计，帮助创造一个独特的办法，美国的欧洲简约而成为一个主要的先驱。平面设计称为企业形象;约瑟夫米勒，罗克曼，设计的海报严重尚未获取1950年代和1960年代时代典型。 从道路标志到技术图表，从备忘录到参考手册，增强了平面设计的知识转让。可读性增强了文字的视觉效果。 设计还可以通过理念或有效的视觉传播帮助销售产品。将它应用到产品和公司识别系统的要素像标志、颜色和文字。连同这些被定义为品牌。品牌已日益成为重要的提供的服务范围，许多平面设计师，企业形象和条件往往是同时交替使用。