DESCRIPTION
The PS2501A-1 and PS2501AL-1 are optically coupled isolators containing a GaAs light emitting diode and an NPN silicon phototransistor to realize an excellent cost performance.
The PS2501A-1 is in a plastic DIP (Dual In-line Package) and the PS2501AL-1 is lead bending type (Gull-wing) for surface mount.
FEATURES
? High isolation voltage (BV = 5 000 Vr.m.s.)
? Ordering number of taping product: PS2501AL-1-E3, E4, F3, F4
? Pb-Free product
? Safety standards ? UL approved: File No. E72422
APPLICATIONS
? Power supply ? Telephone/FAX. ? FA/OA equipment
? Programmable logic controller
PHOTOCOUPLER
PS2501A-1,PS2501AL-1
HIGH ISOLATION VOLTAGE SINGLE TRANSISTOR TYPE MULTI PHOTOCOUPLER SERIES
?NEPOC Series ?
Document No. PN10221EJ03V0DS (3rd edition) Date Published November 2004 CP(K)
The mark shows major revised points.
PACKAGE DIMENSIONS (UNIT : mm)
DIP Type
Lead Bending Type
Data Sheet PN10221EJ03V0DS
2
PS2501A-1,PS2501AL-1
MARKING EXAMPLE
ORDERING INFORMATION
Part Number Order Number Solder Plating
Specification Packing Style Safety Standard
Approval
Application Part
Number *1
PS2501A-1 PS2501A-1 Solder Magazine
case 100 pcs Standard products PS2501A-1
PS2501AL-1 PS2501AL-1 contains lead (UL Approved)
PS2501AL-1-E3 PS2501AL-1-E3 Embossed Tape 1 000 pcs/reel
PS2501AL-1-E4 PS2501AL-1-E4
PS2501AL-1-F3 PS2501AL-1-F3 Embossed Tape 2 000 pcs/reel
PS2501AL-1-F4 PS2501AL-1-F4
PS2501A-1 PS2501A-1-A Pb-Free Magazine case 100 pcs
PS2501AL-1 PS2501AL-1-A
PS2501AL-1-E3 PS2501AL-1-E3-A Embossed Tape 1 000 pcs/reel
PS2501AL-1-E4 PS2501AL-1-E4-A
PS2501AL-1-F3 PS2501AL-1-F3-A Embossed Tape 2 000 pcs/reel
PS2501AL-1-F4 PS2501AL-1-F4-A
*1 For the application of the Safety Standard, following part number should be used.
Data Sheet PN10221EJ03V0DS 3
PS2501A-1,PS2501AL-1
ABSOLUTE MAXIMUM RATINGS (T A = 25°C, unless otherwise specified)
Parameter Symbol Ratings Unit
Diode Reverse Voltage
V R 6 V
Forward Current (DC) I F 30 mA
Power Dissipation Derating
?P D /°C 1.5 mW/°C
Power Dissipation P D 150 mW
Peak Forward Current
*1
I FP 0.5 A Transistor Collector to Emitter Voltage V CEO 70 V
Emitter to Collector Voltage
V ECO 5 V Collector Current I C 30 mA
Power Dissipation Delay
?P C /°C 1.5 mW/°C
Power Dissipation P C 150 mW Isolation Voltage
*2
BV 5 000 Vr.m.s. Operating Ambient Temperature T A ?55 to +100 °C Storage Temperature
T stg
?55 to +150
°C
*1 PW = 100 μs, Duty Cycle = 1%
*2 AC voltage for 1 minute at T A = 25°C, RH = 60% between input and output
Data Sheet PN10221EJ03V0DS
4
PS2501A-1,PS2501AL-1
ELECTRICAL CHARACTERISTICS (T A = 25°C)
Parameter Symbol Conditions MIN. TYP. MAX. Unit
Diode Forward Voltage
V F
I F = 10 mA 1.2 1.4 V
Reverse Current I R V R = 5 V
5 μ
A
Terminal Capacitance C t V = 0 V, f = 1.0 MHz 10 pF Transistor Collector to Emitter Dark
Current
I CEO
V CE = 70 V, I F = 0 mA
100
nA
Coupled Current Transfer Ratio (I C /I F )
*1
CTR I F = 5 mA, V CE = 5 V
50 400 %
Collector Saturation Voltage V CE (sat) I F = 10 mA, I C = 2 mA
0.13 0.3 V
Isolation Resistance R I-O V I-O = 1.0 kV DC 1011
? Isolation Capacitance C I-O V = 0 V, f = 1.0 MHz
0.4
pF
Rise Time *2
t r V CC = 10 V, I C = 2 mA, R L = 100 ? 5 μs
Fall Time
*2t f
7
*1 CTR rank N : 50 to 400 (%) H : 80 to 160 (%) W : 130 to 260 (%) Q : 100 to 200 (%) L : 200 to 400 (%)
*2 Test circuit for switching time
V CC
OUT
?
Data Sheet PN10221EJ03V0DS
5
PS2501A-1,PS2501AL-1
TYPICAL CHARACTERISTICS (T A = 25°C, unless otherwise specified)
200
150
1005002550751001251.5 mW/?C
D i o d e P o w e r D i s s i p a t i o n P D (m W )
Ambient Temperature T A (?C)DIODE POWER DISSIPATION vs.AMBIENT TEMPERATURE
200
150
100
50
0255075100125
1.5 mW/?C
T r a n s i s t o r P o w e r D i s s i p a t i o n P C (m W )
Ambient Temperature T A (?C)
TRANSISTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE
1F o r w a r d C u r r e n t I F (m A )
Forward Voltage V F (V)FORWARD CURRENT vs.FORWARD VOLTAGE
C o l l e c t o r C u r r e n t I C (m A )
Collector to Emitter Voltage V
CE (V)
COLLECTOR CURRENT vs.
COLLECTOR TO EMITTER VOLTAGE
C o l l e c t o r t o E m i t t e r
D a r k C u r r e n t I C
E O (n A )
Ambient Temperature T A (?C)COLLECTOR TO EMITTER DARK
CURRENT vs. AMBIENT TEMPERATURE
Collector Saturation Voltage V CE(sat) (V)
COLLECTOR CURRENT vs.
COLLECTOR SATURATION VOLTAGE
C o l l e c t o r C u r r e n t I C (m A )
Remark The graphs indicate nominal characteristics.
Data Sheet PN10221EJ03V0DS
6
PS2501A-1,PS2501AL-1
Ambient Temperature T A (?C)N o r m a l i z e d C u r r e n t T r a n s f e r R a t i o C T R
NORMALIZED CURRENT TRANSFER RATIO vs. AMBIENT TEMPERATURE
Forward Current I F (mA)
CURRENT TRANSFER RATIO vs.FORWARD CURRENT
Frequency f (kHz)
N
o r m a l i z e d G a i n G V
FREQUENCY RESPONSE
Time (Hr)
C T R (R e l a t i v e V a l u e )
LONG TERM CTR DEGRADATION
Load Resistance R L (?)
S w i t c h i n g T i m e t ( s )
μSWITCHING TIME vs.LOAD RESISTANCE
Load Resistance R L (k ?)
SWITCHING TIME vs.
LOAD RESISTANCE
S w i t c h i n g T i m e t ( s )
μ0.11
10
100
10
100 1 00010 000
t f
t r
t d
t s
I C = 2 mA, V CC = 10 V,CTR = 216 %
–––––
Remark The graphs indicate nominal characteristics.
Data Sheet PN10221EJ03V0DS
7
PS2501A-1,PS2501AL-1
TAPING SPECIFICATIONS (UNIT : mm)
Data Sheet PN10221EJ03V0DS
8
PS2501A-1,PS2501AL-1
PS2501A-1,PS2501AL-1
Data Sheet PN10221EJ03V0DS 9
NOTES ON HANDLING
1. Recommended soldering conditions (1) Infrared reflow soldering
? Peak reflow temperature 260°C or below (package surface temperature) ? Time of peak reflow temperature 10 seconds or less ? Time of temperature higher than 220°C 60 seconds or less ? Time to preheat temperature from 120 to 180°C 120±30 s
? Number of reflows Three
? Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.)
P a c k a g e S u r f a c e T e m p e r a t u r e T (?C )
Time (s)
Recommended Temperature Profile of Infrared Reflow
(2) Wave soldering ? Temperature 260°C or below (molten solder temperature) ? Time
10 seconds or less
? Preheating conditions 120°C or below (package surface temperature)
? Number of times One (Allowed to be dipped in solder including plastic mold portion.)
? Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.)
(3) Soldering by soldering iron
? Peak temperature (lead part temperature) 350°C or below ? Time (each pins)
3 seconds or less
? Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.)
(a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead. (b) Please be sure that the temperature of the package would not be heated over 100°C.
Data Sheet PN10221EJ03V0DS
10
PS2501A-1,PS2501AL-1
PS2501A-1,PS2501AL-1
(4) Cautions
? Fluxes
Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
2. Cautions regarding noise
Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings.
USAGE CAUTIONS
1.Protect against static electricity when handling.
2.Avoid storage at a high temperature and high humidity.
Data Sheet PN10221EJ03V0DS 11
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE.
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information.
Restricted Substance
per RoHS Concentration Limit per RoHS
(values are not yet fixed)
Concentration contained
in CEL devices
-A -AZ
Lead (Pb) < 1000 PPM
Not Detected (*) Mercury < 1000 PPM Not Detected
Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected
PBB < 1000 PPM Not Detected
PBDE < 1000 PPM Not Detected
If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.