文档库 最新最全的文档下载
当前位置:文档库 › [英文硬件手册]NePort系列高性能嵌入式联网RJ45模块--支持1-3路高速串口,集成PoE,超低功耗

[英文硬件手册]NePort系列高性能嵌入式联网RJ45模块--支持1-3路高速串口,集成PoE,超低功耗

NePort?Hardware Manual

Conextop Technologies Co., Ltd.

All rights reserved

Disclaimer

Copyright?2003

Conextop, Inc.

All rights reserved.

Conextop,NePort,with its patent-pending technology, and neChip are trNePortmarks

of Conextop. All other trademarks are the property of their respective owners. Contacts

Contents

NePort Overview (4)

1. Features: (4)

2. Product Character: (4)

NePort Hardware Description (6)

1. NePort Internal Structure (6)

2. NePort Internal Circuit (6)

3. PCB Interface (6)

4. Ethernet Interface (9)

5. Status Leds (9)

6. Capsulation (10)

7. PCB Layout (10)

8.Product Mark (12)

9.Performance Guide (12)

10.Evaluation Kit (13)

NePort Overview

Conextop Technologies target at providing the most reliable and security M2M solution for the worldwide customers, and NePort is the most compact serial-IP module released in 2002, which has embedded all in a standard RJ45 connector, Neport is powered by our network processor SoC(Nechip), which includes a 10/100 MAC/PHY and 256 KB of SRAM on chip. It features a built-in web server for communications with a device via a standard Internet browser. Web capability can be used for remote configuration, real-time monitoring or troubleshooting. Neport has 512 KB of on-chip Flash for web pages and software upgrades. It acts as a dedicated co-processor that optimizes network activities permitting the host microprocessor to function at maximum efficiency.

1. Features:

◆Embed Web Server

Support update customized web

◆Embed Telnet Server

◆Provide RS232/422/485 signals.Can communicate with any devices with serial port

◆Port buffer for every serial port

◆High efficient Device Management and Trouble shoot tools

◆All parameters can be configured through internal web server

◆Provide serial login mode and configure system through serial port

◆Telnet server enables remote management

◆Email Alarm and data encryption

2. Product Character:

◆The most compact size, High intefration

compatible with standard RJ45 connector

◆High Performance, High Reliability, Industrial Temerature

◆32bits RISC NP7 series (NeChip NP7 series)

ARM7TDMI 55DMIPS

◆128KB SRAM (EN:256KB SRAM)

256KB/512KB Code + 32KB Boot

◆10/100Mbps Ethernet Interface (Auto sensing))

◆Provide 1-3 high speed serial ports

◆Serial Port: selectable Data bite 5.6.7.8 bits

◆Serial Port: selectable stop bite 1,2 bits

◆Baud rate: 110 – 460800bps

110 – 921600bps (EN Version)

◆Provide RS485/422 controller

◆Smart/High reliability networking stacks:

ETH、ARP、IP、UDP、TCP、ICMP、PING、BOOTP、AutoIP、DHCP、SNTP、POP3、SMTP、TFTP、DNS、TELNET、HTTP、PPP/PPPoE

SSH、SSL/TLS、HTTPS(EN Optional)

◆Embedded Web Server, support update customized webs

◆Email Alarm according to the triggers(EN Optional)

◆Data Encryption:

128-,192-,256bit AES / Tri-DES (Optional)

◆Multiplex communication modes: TCP Server/client, UDP Uni-cast/Multi-cast modes

◆Provide two programmable I/O

◆S upport Windows 95/98/ME/NT/2000/XP/2003/XP x64/2003 x64 COM driver、Linux

real、TTY、UNIX

◆Operation Voltage: 3.14~3.6 V DC

◆Low Power Consumption: 110 – 155mA @ 3.3V

◆Support POE

◆ 1.5KV electromagnetism isolation

◆All pins support anti-static protection

◆Operation Temperature

0°C to +70°C (32°F to 158°F),5% to 95% RH (Commercial Model)

-40°C to +80°C (-40°F to 176°F),5% to 95% RH (Industrial Model)

◆Storage Temperature

-40°C to +80°C (-40°F to 176°F),5% to 95% RH

NePort Hardware Description

1. NePort Internal Structure

NePort Integrate nechip,PHY,OSC,Reset and power circuit.

Chart2-1. Internal Structure

2. NePort Internal Circuit

Chart2-2. Function Circuit

3. PCB Interface

NePort can provide up to three high speed serial ports with standard CMOS signals which can tolerate 5V TTL signals. In the real application, neport’s serial port directly connect to the local CPU(or other processor) , then user devices can connect to Ethernet through neport now,serial data from local cpu will be sent to neport,and neport will convert the data from serial port to Ethernet according to the networking configuration

NePort Series include –POE,-L,-R,-EN versions, this doc just descript the standard version of neport.

NePort series with 8 pins

Chart2-1. V alid for NePort-L 、NePort-R and the other versions with 8 pins

PinNum Pin Name Type Description

1 GND Power Ground

2 VDD Power Power Input (+3.3V )

3 RESET Input Low level to reset (5V tolerant)

4 TXD Output Serial port: Data Output(5V tolerant)

5 RXD Input Serial port: Data Input(5V tolerant)

6 IO/RTS I/O Programmable I/O with multiplex Function:(5V tolerant)

1.RTS(Request to Send): Output, Hardware Flow Control

2.IO(input/output): Can be configured by web or device

manager ( Only for special models)

3.TCP Connection Status,Invalid when hardware flow

control is enabled

4. System status ,Invalid when hardware flow control is

enabled

5. RS-485/RS422 Controller (RS422: Low level)

7 Default Input Low level valid,Force to load factory setting(5V

tolerant)

Keep this pin be low level for more than 5

seconds,NePort will be forced to load the factory

setting and automatically reboot system

8 IO/CTS I/O Programmable I/O with multiplex Function:(5V tolerant)

1.RTS(Request to Send): InPut, Hardware Flow Control

2.IO(input/output): Can be configured by web or device

manager ( Only for special models)

3.TCP Connection Status,Invalid when hardware flow

control is enabled

4. System status ,Invalid when hardware flow control is

enabled

5. RS-422 Controller: High Level

Mark:

1.Place a 10uF capacitor between power and ground, and had better be close to NePort.

2.Should not connect upload resistance on Reset pin( Pin 3 ).

3.Recommend to connect upload resistance on RTS and CTS pin when uart work under

rs232 mode

4.Recommend to connect download resistance on RTS and CTS pin when uart work under

rs485/422 mode

10Pin Model of Neport Series

Chart2-2. V alid for NePort 、NePort-EN Series PinNum Pin Name Type Description

1 IO/CTS

RXD2 Bid Programmable I/O with multiplex Function:(5V tolerant)

1.RTS(Request to Send): InPut, Hardware Flow Control

2.IO(input/output): Can be configured by web or device

manager ( Only for special models)

3.TCP Connection Status,Invalid when hardware flow

control is enabled

4. System status ,Invalid when hardware flow control is

enabled

5. RS-422 Controller: High Level

6.UART2 TXD

2 GND Power Ground

3 VDD Power Power Input (+3.3V )

4 RESET Input Low level to reset (5V tolerant)

5 TXD1 Output Serial port: Data Output(5V tolerant)

6 RXD1 Input Serial port: Data Input(5V tolerant)

7 IO/RTS

TXD2 Bid Programmable I/O with multiplex Function:(5V tolerant)

1.RTS(Request to Send): Output, Hardware Flow Control

2.IO(input/output): Can be configured by web or device

manager ( Only for special models)

3.TCP Connection Status,Invalid when hardware flow

control is enabled

4. System status ,Invalid when hardware flow control is

enabled

5. RS-485/RS422 Controller (RS422: Low level)

6.UART2 TXD

8 Default Input Low level valid,Force to load factory setting(5V

tolerant)

Keep this pin be low level for more than 5

seconds,NePort will be forced to load the factory

setting and automatically reboot system

9 IO/P+

TXD3 Bid 1.IO(input/output): Can be configured by web or device manager ( Only for special models)

2.Anode output Of PoE

3.UART3 TXD

10 IO/P+

RXD3 Bid 1.IO(input/output): Can be configured by web or device manager ( Only for special models)

2.Cathode output of PoE

3.UART3 RXD

Mark::

1. Place a 10uF capacitor between power and ground, and had better be close to NePort

2. Should not connect upload resistance on Reset pin( Pin 3 )

3. Recommend to connect upload resistance on RTS and CTS pin when uart work under

rs232 mode

4. Recommend to connect download resistance on RTS and CTS pin when uart work under

rs485/422 mode

5. 8Pin Models are compatible with 10Pin models of NePort Series except CTS 、P+、P- signals 。

4. Ethernet Interface

NePort has integrated Ethernet transformer,RJ45 connector and status leds Chart2-3. Standard Ethernet signals(Industrial Starndard) Signal Type

Pin Num

Function Description Mark TX+ Output 1 Transmit signal: Positive TX- Output 2 Transmit signal: cathode RX+ Input 3 Receive signal: Positive RX-

Input 6 Receive signal: cathode Not used 4 Not used 5

Not used 7 Not used 8

SHIELD

Shield (Connect to Ground)

2KV electromagnetism Isolation

Mark: Please refer to Sheet2-4 for detailed pin description of RJ45 connector

5. Status Leds

NePort includes the follow status leds

◆ LINK (Green, Left Led ) ◆

ACT (Yellow ,Right Led )

Chart2-3. NePort Front View (Led)

Right Led Pin 1 Shield(GND)

Shield(GND)

Pin 8 Left Led

Sheet2-4.Description of status leds

LINK LED (Left )

ACT LED (Right )

Status Description

Status Description

ON

Link is normal Flash Transceive Ethernet packets OFF(Flash) Cable dropped / Link

disconnected

OFF

No data flow

6. Capsulation

NePort Shell as below: Chart2-5. Bottom View

Chart2-6. Side View

7. PCB Layout

For high reliability application with NePort embedded in user products,the follow items are strongly recommended:

1. Should place decoupling capacitor(0.1uF) beside neport

2. Place 10uF capacitor between power and ground beside neport

Fixed Shield Pin

mm Dim Min Typ

Max

A 10.78 10.80 10.96 B

11.43 C 6.35 D

2.54 E 2.54 F 1.27 G 37.92 38.20 38.50

H 3.10 3.15 3.20 I

2.80

2.85

2.90

mm Dim Min

Typ Max A 0.20 0.25 0.30 B 10.78 10.80 10.96

C - 17.15 -

D 2.85 3.05 3.25

E - 2.54 -

F -

1.80

-

7- 5- 3 -1

2

9

3. Had better provide isolated/independent power(3.3V) for neport Chart2-7. Recommended PCB Capsulation

NePort has integrated power-on reset circuit inside, no need external circuit to power-on reset neport, so reset pin can be left unconnected, if user need reset neport by additional I/O provided by MCU/DSP, we will recommend the follow application circuit.

Chart2-8. Recommended application circuit

Back

Front

10

8.Product Mark

Product mark includes the follow information. (Chart2-9)

1.Neport series

2.MAC address

3.Part number

4.Operation condition: temperature and work voltage

Chart2-9. Product mark

00-F0-0A-02-BE-01 MAC Address

Part Number

9.Performance Guide

Sheet2-4. NePort electrical parameters

Name Description Min Max Unit Condition

V DD Power Volatage -0.3 3.6 V

I DD Work Current 140 170 mA Full loading (-40℃/

+85℃)

V I Signal input voltage 0 5.5 V

V O Signal output voltage 0 V DD V

V IH High level input voltage 2 - V

V IL Low level input voltage - 0.8 V

V OH High level output voltage V DD-0.4 -

V OL Low level output voltage - 0.4

I OH High level output current -4 - V OH= V DD-0.4V

I OL Low level output current 4 - V OL= 0.4V

Sheet2-5. Normal electrical parameters

Name Description Min Typical Max Unit Condition V DD Work Voltage 3.1 3.3 3.5 V

I DD Work Current 140 150 160 mA

soldering Jointing Jointing Tem:260℃±5℃,DippingTime≤5±0.5s 10.Evaluation Kit

The evaluation kit targets at helping customers to integrate neport in their products efficiently. It includes the follow components

◆NePor Evaluation Board

◆NePort

◆+9V Power Adaptor

◆RS232 cross-over cable(DB9,Fmale-Female)

◆CAT5e UTP RJ45M/M

◆Product Disk

Chart 2-10. Evaluation Kit

Description of EVB

This Kit provide the whole platform for testing neport series, it includes ae neport(Standard version), a neport plug with 8/10 pins,standard RS232 interface with coms to rs232 converter chip and led indicators

Chart 2-11. Evaluation Board

00.F0.0A.02.00.1A

Chart 2-10. Schematic of Evaluation Board

RS232 Interface

There is one onboard RS232 chip from SIPEX, it is used to convert 3.3V COMS signals to RS232 signal, normally, RS232 interface provide one DB9 connector to communicate with external DTE, for instance, connect to PC serial port.

Chart 2-11. DB9 Pin Information

Sheet 2-6. Signal Description of RS232 Interface

NePort Signal Terminal Device(DTE)

DB9 Pin # Signal Name DB9 Pin # Signal Name

2 RXD 2 TXD

3 TXD 3 RXD

5 GND 5 GND

7 RTS 7 CTS

8 CTS 8 RTS

Mark:1. Pin not listed in the above sheet is not used by evaluation board

2. Recommend to make the shield of DB9 connect to ground

Power

On board DC JACK with internal size : 2.0mm,,power circuit support pole protection,input voltage arrange:7.5V~12V。adjustable power chips are LM2596 DC-DC and

LM1117-3.3V LDO from SIPEX。

Selectable Channel Switch

The Evaluation board provide 8bits DIP16/8 switch to select neport1 or neport2 to communicate with external rs232 interface. Push switch to ON will enable the corresponding signal.

Attention:

1. User just can enable one group of this 8bits switch,(group 1:one:1-4 , Group 2:5-8), or

Evaluation board can’t communicate with external rs232 devices

2. When all of 8bits switch are disconnected or one group are disconnect but no neport

on the other group, such setting may cause no signal output to rs232

8Pin/2.0 pitch header

The Evaluation board provides 8pins pitch header for OEM/ODM customized development, and this pitch header can make neport signals connect to user’s MCU/DSP

efficiently to debug or testing according to the real application

Attention:

Should disconnect the extern rs232 interface to avoid effect testing result

Buttons

The Evaluation Board integrates three buttons used as reset / defaulting setting

NePort Summary

Embedded Seial-IP series NePort –L Series NePort-R Series NePort Series NePort-EN Series Single port series LX LX -485 RX RX -485 SX

SX -485 EXH EXH -485 ESX

Flash

Code/Boot(KB) 128k /32 128k /32 256k /32 256k /32 512k /32 512k /32 512k /32 512k /32 512k /32 SRAM(KB) 80/128 80/128 128 128 256 256 256 256 256 Memory and Speed

Speed (MIPS)

55 55 55 55 55 55 60 60 60 ARM7TDMI Y Y Y Y Y Y Y Y Y Core and System Multi-T RTOS Y Y Y Y Y Y Y Y Y Ethernet Speed (M) 10/100 10/100 10/100 10/100 10/100 10/100 10/100 10/100 10/100 Y Y Y Y Y Y Y Y Y RS232 Uart RS485/422

Y

Y

Y

Y

Y Max-Baudrate(bps) 115200 115200 460800 460800 460800 460800 921600 921600 921600 Serial Interfaces

Serial port Number

1 1 1 1 1 1 1/2/3 1/2/3 1/2/3 Programmable I/O PIO Number --

2 -- 2 -- -- -- 2 2 ARP/IP/ICMP/DHCP /BOOTP/TCP/UDP Y

Y Y Y Y Y Y Y Y TFTP Y Y Y Y Y Y Y Y Y SNTP -- -- -- -- Y Y -- Y Y Http Server (web customized) --Y Y Y Y Y Y Y Y Telnet Server Y(*) Y(*) Y Y Y Y Y Y Y DNS

Y(*) Y(*) Y(*) Y(*) Y Y Y Y Y Smtp (Email Trigger) -- -- -- -- Y(*) Y(*) -- Y Y Protocol stacks

PPP/PPPOE

-- -- -- -- -- Y(*) -- -- Y SSH -- -- -- -- -- -- -- -- Y SSL/TLS -- -- -- -- -- -- -- -- Y Https -- -- -- -- -- -- -- -- Y Advanced encryption protocols

Smtps

-- -- -- -- -- -- -- -- Y AES

-- -- -- -- -- -- -- -- Y DES/Triple-DES -- -- -- -- -- -- -- -- Y RC4 -- -- -- -- -- -- -- -- Y Encryption Arithmetic

MD5

-- -- -- -- -- -- -- -- Y Power suppler(V) 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 Analog parameters

I/O Tolerant(V)

5 5 5 5 5 5 5 5 5 10Base-T Activity 165 165 165 165 165 165 165 165 165 PowerConsumption (mA)

100Base-T Activity

155 155 155 155 155 155 155 155 155 Operating temperature arrange

C = 0 - +75°C I = - 40 - +85°C

C,I C,I C,I C,I C,I C,I C,I C,I C,I Package Option

(RJ45)

RJ45 Low Cost

RJ45 Low Cost

RJ45

RJ45

RJ45

RJ45

RJ45

RJ45

RJ45

More details by: https://www.wendangku.net/doc/ab982973.html,/products/embeddedsolution/wiredmodules/index.htm For details contact your local Conextop representative or

Conextop directly:

call OEM sales support at 86-755-26505615

More details about NePort at https://www.wendangku.net/doc/ab982973.html,

? Conextop Technologies –November 2003 - All rights reserved The Conextop corporate logo is a registered trademark of Conextop Technology. All other names are the property of their respective owners.

?2003 Conextop, Inc. All rights reserved. Conextop, NePort, with its patent-pending technology, and neChip are trademarks of Conextop. All other trademarks are the property of their respective owners. Specifications subject to change without notice. All rights reserved.

相关文档