文档库

最新最全的文档下载
当前位置:文档库 > 日立 钻孔机代码

日立 钻孔机代码

––CNC番號是error alarm 發生的CNC番號。

––訊息番號訊息的番號表示000~919的番號。

000~199:CNC關係的訊息,和操作軸沒關係。

200~399:機械特有的訊息。

400~599:操作軸關係的訊息。

600~919:操作軸移動方向關係的訊息。

––訊息26各文字以內的訊息。

回復條件START、RESET、EMG表示為回復的條件。

注)狀態訊息是藍色、操作訊息是黃色、error、alarm訊息是以紅色表示。

9-2 MESSAGE TABLE

NO.000 SYSTEM PA RAMETER ERROR EMG 系統參數錯誤

NO.001 PA RITY(TH)A LA RM RESET 紙帶水平同位(TH)警報

NO.002 PA RITY(TV)A LA RM RESET 紙帶垂直同位(TV)警報

NO.003 CONSTANT TOO LA RGE RESET 常數太大

NO.004 INV A LID A DDRESS RESET 位址無效

NO.005 INV A LID CONSTANT RESET 常數無效

NO.006 ILLEGA L“–”CODE RESET 不合法“–”碼

NO.007 ILLEGA L“.”CODE RESET 不合法“.”碼

NO.008 UNDEFINE A DDRESS RESET 未定義位址

NO.009 UNDEFINE G CODE RESET 未定義G 碼

NO.010 UNDEFINE M CODE RESET 未定義M 碼

NO.011 INV A LIE END CODE RESET 無效結束碼

NO.012 ILLEGA L REPEAT COMMAND RESET 不合法副程式呼叫

NO.013 ILLEGA L REPEAT COMMAND RESET不合法重覆指令

NO.014 NO SUCH SUBPROGRAM RESET 未登錄副程式

NO.015 ILLEGA L SUBPROGRAM NEST RESET 多重副程式呼叫

NO.016 ILLEGA L DOUBLE ADDRESS RESET 不合法重覆位址

NO.017 NOT FOUND SEQUENCE NO RESET 未發現順序控制編號NO.018 ILLEGA L S&R CA LL RESET 不合法Step&Repeat指令呼出

NO.019 INV A LID MA CHINE HOME RESET 原點復歸未實施

NO.020 ILLEGA L RETURN CODE RESET 不合法程式結束碼

NO.021 ILLEGA L S&R RESET 不合法Step&Repeat指令開始

NO.022 ILLEGA L S&R END CODE RESET 不合法Step&Repeat指令結束

NO.023 ILLEGA L PA R T PROGRAM RESET 不合法紙帶格式(FORMAT)NO.024 FD FULL RESET 磁碟容量已滿

NO.025 FD NOT READY RESET 磁碟片未準備就緒

NO.026 ILLEGA L F COMMAND RESET 進刀速設定超出範圍外

NO.027 ILLEGA L S COMMAND RESET 回轉速設定超出範圍外

NO.028 ILLEGA L T COMMAND RESET 工具徑設定超出範圍外

NO.030 FD FILE PROTECTED RESET 禁止File讀出

NO.031 FILE W RITE PROTECTED RESET 禁止File寫入

NO.032 NO SUCH FILE RESET File未登錄

NO.033 ILLEGA L FILE NAME RESET 檔案名程不正確

NO.034 LIMIT OF SUBPROGRAM RESET 副程式超出限制

NO.035 ILLEGA L S&R NEST RESET 多重Step&Repeat呼出

NO.036 ILLEGA L ‘+’ CODE RESET 不合法“+”碼

NO.037 CONSTANT OUT OF RANGE RESET 常數超出被定範圍

NO.038 ILLEGA L PA RAMETER DATA RESET 不合法參數資料

NO.039 ILLEGA L COMMAND CONDITION RESET 不合法命令組合NO.040 FORMAT ERROR RESET 格式錯誤(FORMAT)

NO.041 DEVICE BUSY RESET 裝置使用中(忙碌)

NO.042 ILLEGA L MESSA GE FILE EMG 不合法的訊息檔案

NO.043 ILLEGA L MACRO FILE EMG 不合法的巨集檔案

NO.044 ILLEGA L SUBPROGRAM STA R T RESET 不合法的輔助程式開始NO.060 END OF PRPGRAM STA R T 作業完了

NO.061 PROGRAM STOP STAR T 程式停止

NO.062 OPTIONAL STOP STA R T 選擇性停止

NO.064 TOP OF PROGRAM STA R T 程式開始

NO.067 READY FOR RESTAR T STAR T 程式準備完畢

NO.068 ILLEGA L HEADER COMMAND STAR T 不合法的程式頭指令

NO.072 ILLEGA L DEVICE RESET 未定義裝置

NO.079 WAITING FOR STA R T STA R T 等待開始狀態

NO.080 EMULATER ERROR EMG 內部演算錯誤

NO.100 DISK HA RDWARE ERROR EMG 磁碟硬體錯誤

NO.104 CMOS RAM SUM CHECK ERROR EMG CMOS RAM 檢查錯誤NO.110 DISK HARDWARE ERROR EMG 伺服器尚未就緒

NO.111 EXTERNAL IN/OUTPUT STA R T 外部裝置警報

NO.113 SERVO OPTICAL FIBER EMG 伺服光纖關係警報

NO.114 PARAMETER SETTING ERROR EMG 參數設定錯誤

NO.116 SEQENCER OPTICA L FIBER EMG 順序控制光纖關係警報

NO.117 DWQENCER HA RDWARE DGN.14 EMG 順序控制硬體錯誤DGN.14

NO.119 RS-232C 1 ERROR DGN.16 STA R T RS-232C通信埠 1 錯誤DGN.16

NO.120 RS-232C 2 ERROR DGN.16 STA R T RS-232C通信埠 2 錯誤DGN.16

NO.122 MAIN CPU ERROR DGN.000 EMG 主CPU硬體錯誤DGN.000

NO.123 SERVO CPU ERROR DGN.12,413 EMG 伺服CPU硬體錯誤DGN.12,413

NO.126 BPRKEN BATTERY EMG 電池異常

NO.127 DNC COMMUNICATION A LARM RESET DNC通信警報

NO.199 INTERNAL ERROR EMG 內部錯誤

NO.200 ILLEGA L CANNED CYCLE RESET 不當程式指令(DIL IC)

NO.201 ILLEGA L CANNED TEXT RESET 不當程式令令(文字)

NO.202 ILLEGA L CANNED CIRCLE RESE 不當程式指令(擴大孔)

NO.203 ILLEGA L CANNED SLOT RESET 不當程式指令(槽孔)

NO.205 ILLEGA L DRILL HIT COMMAND RESET 不當加工指令

NO.206 ILLEGA L DRILL CYCLE DATA RESET 不當加工循環資料

NO.207 READY FOR REVERSE STA R T 加工反轉就緒

NO.208 END OF MACHINE REVERSE STA R T 加工反轉結束

NO.209 HOLE NOT EQUAL STAR T 孔數不一致

NO.210 ILLEGA L TOOL PATH COMMAND RESET 不當切削加工指令

NO.213 ILLEGA L TOOL BIT SELECTION RESET 不當工具別選擇

NO.215 NC BUFFER OVER NC RESET NC 緩衝區超出

NO.216 PRESS THEN RESET THE EMG STOP RESET 請實施RESET EMG鍵以載入系統NO.250 LIMIT OF TOOL BIT LIFE STAR T 工具壽命終了

NO.251 UNDEFINE T CODE STA R T 未定義T CODE

NO.252 CHA NGE OF ATC TOOL BLOCK STAR T 請交換ATC部工具

NO.254 ILLEGA L NUMBER OF TOOL RESET 不當工具數分配(TOOLMNG)

NO.255 ILLEGA L SPINDLE SELECTION RESET 不當SPINDLE選擇(BH機能)

NO.256 CCD SENSOR A LA RM RESET CCD感測器警報

NO.257 NO DETECTION OF BIT HIGHT STA R T CCD感測器工具長度偵測不到

NO.258 TOOL DIAMETER ERR(DGN.181) STAR T CCD感測器工具直徑偵測異常

NO.260 CHECK STATION NG1(LONG) STA R T 裝著後確認工具長度(長)

NO.261 CHECK STATION NG2(LONG) STA R T 排出前確認工具長度(長)

NO.262 TOOL LET OUT ERROR START工具排出錯誤

NO.263 CHECK STATION NG1(SHORT) STA R T 裝著後確認工具長度(短)

NO.264 CHECK STATION NG2(SHORT) STA R T 排出前確認工具長度(短)

NO.265 CHECK STATION SENSOR A LARM STA R T CCD 感測器內有異物檢出

NO.266 HIGHT DETECTOR ALA RM STA R T CCD感測器工具刃先檢出異常

NO.267 TOOL LET OUT ERROR STA R T 工具釋放錯誤

NO.268 PANEL HEIGHT SENSOR ERROR RESET 自動R點設定機能感測異常檢出NO.269 AUTO UPLIM DATA ERROR #129 STA R T 自動R點設定機能參數異常DGN.129 NO.270 Z AXIS ORIGIN ERROR RESET Z軸原點復歸錯誤

NO.271 X,Y AXIS ORIGIN ERROR RESET X,Y軸原點復歸錯誤

NO.275 WORK ZERO A LA RM RESET 工作原點錯誤

NO.276 BOA RD EXCHA NGE POS. ERROR RESET 基板交換位置錯誤

NO.277 SUPPLY WORK NOT EQUAL RESET 供給基板板數不一致

NO.278 NO PANEL ON TABLE RESET 自動R點設定機能基板未發現

NO.280 ATC LOCK STAR T ATC鎖住

NO.282 M A DDRESS LOCK RESET M CODE鎖住

NO.283 REPLA CE TOOL PALLET,

TOOL NOT AV A ILABLE STA R T 請交換供給部工具盤(工具已用完)

NO.284 REPLA CE TOOL PALLET,

SWITH ATCIV ATE STAR T 請交換供給部工具盤(SWITCH ON)

NO.285 CHECK POD STA R T 排出,裝著POD確認

NO.286 INSERT TOOL INTO COLLET MANUA LLY STA R T

手動將工具插入COLLET中(粗徑)

NO.287 REMOVE TOOL INTO COLLET MANUA LLY STA R T

手動將COLLET之工具排出(粗徑)

NO.290 ATC CHUCK A LARM(LOW ER) STA R T ATC CHUCK異狀(下降端)

NO.291 ATC CHUCK A LARM(UPER) STA R T ATC CHUCK異狀(上昇端)

NO.292 CHECK ATC CHUCK NG(LONG) STA R T 檢查ATC CHUCK 鑽針(長)

NO.293 CHECK ATC CHUCK NG (SHOR T) STA R T 檢查ATC CHUCK鑽針(短)NO.294 A LL SPINDLES CA NCELLED RESET 全部SPINDLE軸取消

NO.300 SPINDLE FUSE A LA RM STA R T SPINDLE FUSE警報

NO.301 SPINDLE INVERTER A LARM EMG SPINDLE變頻器警報

NO.302 LOW AIR PRESSURE STA R T 空壓不足

NO.303 COLLING UNIT THERMA L A LARM EMG 主軸油冷卻裝置熱電驛警報

NO.304 COOLING UNIT TEMPERATURE STA R T 主軸油冷卻裝置油溫警報

NO.305 V A CLUM THARMAL A LARM EMG 集塵機熱電驛警報

NO.306 ATC POINT A LA RM STA R T A TC位置警報

NO.307 BDD ALA RM STA R T 斷針警報(BDD)

NO.308 EXTERNAL DEVICE ALA RM STA R T 外部裝置警報

NO.310 FRONT DOOR OPENED STA R T 前門被打開

NO.311 SAFETY SENSER A LARM 1 STAR T 安全SENSOR警報1 NO.313 SPINDLE OIL SIGNA L RESET SPINDLE油信號警報

NO.314 A BC DEVICE A LA RM STAR T A BC裝置警報

No.315 DRYING UNIT OFF STAR T 空氣乾燥機停止中

No.316 WORK CLAMP A LAR T RESET 基板固定CLAMP機能異常檢出No.317 PIN CLAMP A LARM RESET PIN CLAMP機能異常

No.318 WORK PRESS A LARM RESET 押板機能動作異常

No.319 SAFETY SENSOR A LARM RESET 安全SENSOR警報2

No.320 XY A XIS INTERLOCK(G64.4) EMG X,Y軸連結鎖住(G64.4) No.321 Z AXIS INTERLOCK(G72.4) EMG Z軸連結鎖住(G72.4)

No.322 CUTTING INTERLOCK(G00.1) EMG 切削連結鎖住(00.1)

No.323 SPINDLE OFF EMG SPINDLE 停止中

No.324 MACHIINE LOCK EMG 機械鎖定

No.325 WAITING FOR M-ANS.DGN.039 RESET M CODE等待回應

No.326 STA R T INHIBIT EMG 啟動停止

No.327 WAIT FOR WARM-UP SPINDLE EMG SPINDLE暖機中

No.328 EXECUTING ABC CYCLE EMG ABC動作中

No.329 WAITING FOR OPERATINO STA R T 等待狀態

No.330 END OF PROGRAM STAR T 作業完了

No.331 PUSHING WORKPRESS EMG 押板機能動作中

No.337 A BC NOT REA DY STA R T 外部裝置A BC未就續No.346 PA CK COMMUNICATION A LARM X11-12 EMG PA CK通訊異常No.347 DEA E STOP ERROR EMG 超極限檢出警報

No.350 BDD A LARM RESET 斷針警報(BDD)

No.351 PRESET SCHEDULE EMG 1V/1W加工異常

No.352 SELECTED ILLEGA L MODE RESET 加工模式異常

No.353 RECLINNING A LARM RESET 板架柵欄警報(A BC) No.354 TOOL ASSINGNMENT ERROR,RESET 工具分配錯誤,檢查工具CHECK ON TOOL PALLET PA GE 分配頁

No.403 X ENCODER ALA RM EMG X軸編碼器警報

No.405 X OVER SERVO DLOOP EMG X軸伺服迴路超出行程No.406 X AXIS INTERLOCK EMG X軸聯結警報

No.407 X VELOCTY A LARM EMG X軸速度警報

No.408 X REFERENCE POINT A LA RM EMG X軸參考點警報

No.409 X SERVO A LA RM EMG X軸伺服關係警報

No.413 Y ENCODER ALA RM EMG Y軸編碼器警報

No.415 Y OVER SERVO DLOOP EMG Y軸伺服迴路超出行程

No.416 Y AXIS INTERLOCK EMG Y軸聯結警報

No.417 Y VELOCTY A LARM EMG Y軸速度警報

No.418 Y REFERENCE POINT A LA RM EMG Y軸參考點警報

No.419 Y SERVO A LA RM EMG Y軸伺服關係警報

No.423 Z1 ENCODER A LARM EMG Z1軸編碼器警報

No.425 Z1 OVER SERVO DLOOP EMG Z1軸伺服迴路超出行程

No.426 Z1 A XIS INTERLOCK EMG Z1軸聯結警報

No.427 Z1 VELOCTY POINT ALA RM EMG Z1軸速度警報

No.428 Z1 REFERENCE POINT A LA RM EMG Z1軸參考點警報

No.429 Z1 SERVO A LA RM EMG Z1軸伺服關係警報

NO.433 Z2 ENCODER ALA RM EMG Z2軸編碼器警報

NO.435 Z2 OVER SERVO DLOOP EMG Z2軸伺服迴路超出行程NO.436 Z2 A XIS INTERLOCK EMG Z2軸聯結警報

NO.437 Z2 VELOCTY A LA RM EMG Z2軸速度警報

NO.438 Z2 REFERENCE POINT A LA RM EMG Z2軸參考點警報

NO.439 Z2 SERVO A LA RM EMG Z2軸伺服關係警報

NO.443 Z3 ENCODER ALA RM EMG Z3軸編碼器警報

NO.445 Z3 OVER SERVO DLOOP EMG Z3軸伺服迴路超出行程NO.446 Z3 A XIS INTERLOCK EMG Z3 軸聯結警報

NO.447 Z3 VELOCTY A LA RM EMG Z3軸速度警報

NO.448 Z3 REFERENCE POINT A LA RM EMG Z3軸參考點警報

NO.449 Z3 SERVO A LA RM EMG Z3軸伺服關係警報

NO.453 Z4 ENCODER ALA RM EMG Z4軸編碼器警報

NO.455 Z4 OVER SERVO DLOOP EMG Z4軸伺服迴路超出行程

NO.456 Z4 A XIS INTERLOCK EMG Z4軸聯結警報

NO.457 Z4 VELOCTY A LA RM EMG Z4軸速度警報

NO.458 Z4 REFERENCE POINT A LA RM EMG Z4軸參考點警報

NO.459 Z4 SERVO A LA RM EMG Z4軸伺服關係警報

NO.463 Z5 ENCODER ALA RM EMG Z5軸編碼器警報

NO.465 Z5 OVER SERVO DLOOP EMG Z5軸伺服迴路超出行程

NO.466 Z5 A XIS INTERLOCK EMG Z5軸聯結警報

NO.467 Z5 VELOCTY A LA RM EMG Z5軸速度警報

NO.468 Z5 REFERENCE POINT A LA RM EMG Z5軸參考點警報

NO.469 Z5 SERVO A LA RM EMG Z5軸伺服關係警報

NO.473 Z6 ENCODER A LA RM EMG Z6軸編碼器光學尺警報NO.475 Z6 OVER SERVO DLOOP EMG Z6軸伺服迴路超出行程

NO.476 Z6 A XIS INTERLOCK EMG Z6軸聯結警報

NO.477 Z6 VELOCTY A LA RM EMG Z6軸速度警報

NO.478 Z6 REFERENCE POINT A LA RM EMG Z6軸參考點警報

NO.479 Z6 Z6 SERVO ALA RM EMG Z6軸伺服關係警報

NO.600 X+ STORED STROKE 1 RESET X+側超出加工領域檢出

NO.601 X–STORED STROKE1 RESET X–側超出加工領域檢出

NO.602 X+ STORED STROKE2 RESET X+側使用者設定加工領域超出OT側檢出

NO.603 X–STORED STROKE 2 RESET X–側使用者設定加工領域超出OT側檢出

NO.604 X+ STORED STROKE 3 RESET X+側超出機械參數設定領域檢出

NO.605 X–STORED STROKE 3 RESET X–側超出機械參數設定領域檢出

NO.620 Y+ STORED STROKE 1 RESET Y+側超出加工領域檢出

NO.621 Y–STORED STROKE 1 RESET Y–側超出加工領域檢出

NO.622 Y+STORED STROKE 2 RESET Y+側使用者設定加工領域超出OT側檢出

NO.623 Y–STORED STROKE 2 RESET Y–側使用者設定加工領域超出OT側檢出

No.624 Y1+STORED STROKE 3 RESET Y+側超出機械參數領域檢出

No.625 Y1-STORED STROKE 3 RESET Y-側超出機械參數領域檢出

No.640 Z1+STORED STROKE 1 RESET Z1+側超出加工領域檢出

No.641 Z1-STORED STROKE 1 RESET Z1-側超出加工領域檢出

No.642 Z1+STORED STROKE 2 RESET Z1+側使用者設定加工領域超出OT側檢出No.643 Z1-STORED STROKE 2 RESET Z1-側使用者設定加工領域超出OT側檢出No.644 Z1+STORED STROKE 3 RESET Z1+側超出機械參數領域檢出

No.645 Z1-STORED STROKE 3 RESET Z1-側超出機械參數領域檢出

No.660 Z2+STORED STROKE1 RESET Z2+側超出加工領域檢出

No.661 Z2-STORED STROKE1 RESET Z2-側超出加工領域檢出

No.662 Z2+STORED STROKE2 RESET Z2+側使用者設定加工領域超出OT側檢出No.664 Z2+STORED STROKE3 RESET Z2+側超出機械參數設定領域檢出

No.665 Z2-STORED STROKE3 RESET Z2-側超出機械參數設定領域檢出

No.680 Z3+STORED STROKE1 RESET Z3+側超出加工領域檢出

No.681 Z3-STORED STROKE1 RESET Z3-側超出加工領域檢出

No.682 Z3+STORED STROKE2 RESET Z3+側使用者設定加工領域超出OT側檢出No.683 Z3-STORED STROKE2 RESET Z3-側使用者設定加工領域超出OT側檢出No.684 Z3+STORED STROKE3 RESET Z3+側超出機械參數設定領域檢出

No.685 Z3-STORED STROKE3 RESET Z3-側超出機械參數設定領域檢出

No.700 Z4+STORED STROKE1 RESET Z4+側超出加工領域檢出

No.701 Z4-STORED STROKE1 RESET Z4-側超出加工領域檢出

No.702 Z4+STORED STROKE2 RESET Z4+側使用者設定加工領域超出OT側檢出No.703 Z4-STORED STROKE2 RESET Z4-側使用者設定加工領域超出OT側檢出No.704 Z4+STORED STROKE3 RESET Z4+側超出機械參數設定領域檢出

No.705 Z4-STORED STROKE3 RESET Z4-側超出機械參數設定領域檢出

No.720 Z5+STORED STROKE1 RESET Z5+側超出加工領域檢出

No.721 Z5-STORED STROKE1 RESET Z5-側超出加工領域檢出

No.722 Z5+STORED STROKE2 RESET Z5+側使用者設定加工領域超出OT側檢出

No.723 Z5-STORED STROKE2 RESET Z5-側使用者設定加工領域超出OT側檢出No.724 Z5+STORED STROKE3 RESET Z5+側超出機械參數設定領域檢出

No.725 Z5-STORED STROKE3 RESET Z5-側超出機械參數設定領域檢出

No.740 Z6+STORED STROKE1 RESET Z6+側超出加工領域檢出

No.741 Z6-STORED STROKE1 RESET Z6-側超出加工領域檢出

No.742 Z6+STORED STROKE2 RESET Z6+側使用者設定加工領域超出OT側檢出No.743 Z6-STORED STROKE2 RESET Z6-側使用者設定加工領域超出OT側檢出No.744 Z6+STORED STROKE3 RESET Z6+側超出機械參數設定領域檢出

No.745 Z6-STORED STROKE3 RESET Z6-側超出機械參數設定領域檢出

No.1000 DOWN LOA D ERROR POWER OFF 下載警報

No.1001 ILLEGAL MESSA GE FILE POW ER OFF 不合法訊息檔案

No.1002 COMMON PARAMETER ERROR POW ER OFF 參數錯誤

No.1003 FD TASK CREATE ERROR POWER OFF FD工作建立錯誤

No.1005 SUBSYSTEM NOT ENTRY POW ER OFF 副系統未就續

No.1006 SUM INTERNAL ERROR POWER OFF SMU內部錯誤

No.1007 PUBDEF NOT ENTRY POWER OFF PUBDEF未進入

No.1008 PUBDEF A REA OVER POW ER OFF PUBDEF超出範圍

No.1039 MCU COMMAND TIME OVER POW ER OFF MCU指令時間超過

No.1040 CNC POW ER ERROR POW ER OFF CNC電源警報

No.1041 SMU RAM PARITY ERROR POW ER OFF SMU RAM同位元檢查錯誤

No.1042 BUS DEAD LOCK POW ER OFF BUS 死結

No.1043 SMU BUS ERROR POW ER OFF SMU BUS錯誤

No.1044 CNC THERMAL A LARM POW ER OFF CNC溫度警報