8-PIN DIP, 400 V BREAK DOWN VOLTAGE, TRANSFER TYPE
2-ch Optical Coupled MOS FET
Solid State Relay
OCMOS FET
PS7141-1C,PS7141L-1C
DESCRIPTION
The PS7141-1C and PS7141L-1C are transfer type solid state relays containing normally open (N.O.) contact and normally close (N.C.) contact on output side.
They are suitable for analog signal control because of their low offset and high linearity. The PS7141L-1C has a surface mount type lead.
FEATURES
? 2 channel type (1 a + 1 b output) ? Low LED operating current (I F = 2 mA) ? Designed for AC/DC switching line changer ? Small package (8-pin DIP) ? Low offset voltage
? PS7141L-1C: Surface mount type ? UL approved: File No. E72422 (S) ? BSI approved: No. 8245/8246 ? CSA approved: No. CA 101391
APPLICATIONS
? Exchange equipment ? Measurement equipment ? FA/OA equipment
Document No. PN10280EJ01V1DS (1st edition) (Previous No. P12274EJ7V0DS00) Date Published February 2003 CP(K)
The mark shows major revised points.
PACKAGE DIMENSIONS (in millimeters)
2
Data Sheet PN10280EJ01V1DS
ORDERING INFORMATION (Solder Contains Lead)
Part Number Package Packing Style Application Part Number *1
PS7141-1C 8-pin DIP Magazine case 50 pcs PS7141-1C
PS7141L-1C PS7141L-1C
PS7141L-1C-E3 Embossed Tape 1 000 pcs/reel
PS7141L-1C-E4
*1 For the application of the Safety Standard, following part number should be used.
ORDERING INFORMATION (Pb-Free)
Part Number Package Packing Style Application Part Number *1
PS7141-1C-A 8-pin DIP Magazine case 50 pcs PS7141-1C
PS7141L-1C-A PS7141L-1C
PS7141L-1C-E3-A Embossed Tape 1 000 pcs/reel
PS7141L-1C-E4-A
*1 For the application of the Safety Standard, following part number should be used.
ABSOLUTE MAXIMUM RATINGS (T A = 25 °C, unless otherwise specified)
Ratings Unit
Parameter Symbol
Diode Forward Current (DC) I F 50 mA
Voltage V R 5.0 V
Reverse
Power
Dissipation P D 50 mW/ch
Peak Forward Current *1I FP 1 A
MOS FET Break Down Voltage V L 400 V
Continuous Load Current I L 150 mA
I LP 300 mA
Pulse Load Current *2
(AC/DC Connection)
Dissipation P D 375 mW/ch
Power
500 Vr.m.s.
Isolation Voltage *3BV 1
Total Power Dissipation P T 850 mW
Operating Ambient Temperature T A?40 to +85 °C
Storage Temperature T stg?40 to +100 °C
*1PW = 100 μs, Duty Cycle = 1 %
*2PW = 100 ms, 1 shot
*3AC voltage for 1 minute at T A = 25 °C, RH = 60 % between input and output
Data Sheet PN10280EJ01V1DS 3
RECOMMENDED OPERATING CONDITIONS (T A = 25 °C)
TYP.
Unit
MAX.
Parameter Symbol
MIN.
LED Operating Current I F 2 10 20 mA
LED Off Voltage V F 0 0.5 V
4
Data Sheet PN10280EJ01V1DS
ELECTRICAL CHARACTERISTICS (T A = 25 °C)
Parameter Symbol Conditions MIN.
TYP.
MAX.
Unit Diode Forward
Voltage V F I F = 10 mA 1.2 1.4 V
Reverse
Current I R V R = 5 V 5.0 μA
MOS FET Off-state Leakage
Current I Loff N.O.:
I F = 0 mA, V D = 400 V 0.03 1.0 μA
N.C.:
I F = 10 mA, V D = 400 V
Output
Capacitance
C out N.O.:
V D = 0 V, f = 1 MHz 65 pF/ch
N.C.:
V D = 0 V, f = 1 MHz, I F = 10 mA 185
Coupled LED On-state Current I Fon N.O.:
I L = 150 mA 2.0 mA
LED Off-state Current I Foff N.C.:
I L = 150 mA 2.0 mA
On-state
Resistance
R on1 N.O.:
I F = 10 mA, I L = 10 mA 20 30 ?
N.C.:
I F = 0 mA, I L = 10 mA 24 30
R on2 N.O.:
I F = 10 mA, I L = 150 mA, t ≤ 10
ms
16 25
N.C.:
I F = 0 mA, I L = 150 mA, t ≤ 10 ms 16 25
Turn-on
Time *1t on (N.O.)I F = 10 mA, V O = 5 V, R L = 500 ?,
0.33
1.0
ms
t on (N.C.) PW
≥ 10 ms 0.02 0.2
Turn-off
Time *1t off (N.O.)0.03 0.2
t off (N.C.)0.20 1.0
Isolation
Resistance
R I-O V I-O = 1.0 kV DC 109?
Isolation
Capacitance
C I-O V = 0 V, f = 1 MHz 1.1 pF/ch
Data Sheet PN10280EJ01V1DS 5
*1 Test Circuit for Switching Time
V L
I F
Pulse Input
Input monitor monitor
V O
V O N.O. (between pin 5 and 6)N.C. (between pin 7 and 8)
Data Sheet PN10280EJ01V1DS
6
TYPICAL CHARACTERISTICS (T A = 25 °C, unless otherwise specified)
100
85
7550
250–25
2060
80100
400M a x i m u m F o r w a r d C u r r e n t I F (m A )
Ambient Temperature T A (?C)MAXIMUM FORWARD CURRENT vs.AMBIENT TEMPERATURE
LOAD CURRENT vs. LOAD VOLTAGE
L o a d C u r r e n t I L (m A )
Load Voltage V L (V)
100
85
750–25
50
25200
300
100
0M a x i m u m L o a d C u r r e n t I L (m A )
Ambient Temperature T A (?C)
MAXIMUM LOAD CURRENT vs.AMBIENT TEMPERATURE
O f f -s t a t e L e a k a g e C u r r e n t I L o f f (A )
Applied Voltage V D (V)
OFF-STATE LEAKAGE CURRENT vs.APPLIED VOLTAGE
F o r w a r d V o l t a g e V F (V )
Ambient Temperature T A (?C)AMBIENT TEMPERATURE
FORWARD VOLTAGE vs.
O u t p u t C a p a c i t a n c e
C o u t (p F )
Applied Voltage V D (V)
OUTPUT CAPACITANCE vs.APPLIED VOLTAGE
101010
1010
Data Sheet PN10280EJ01V1DS 7
Normalized to 1.0 at T A = 25 ?C,I F = 10 mA, I L = 10 mA (N.O.), I F = 0 mA, I L = 10 mA (N.C.)
0.51.52.03.01.02.50.0100
755025–25
0N o r m a l i z e d O n -s t a t e R e s i s t a n c e R o n
Ambient Temperature T A (?C)
NORMALIZED ON-STATE RESISTANCE vs.AMBIENT TEMPERATURE
N.C.
N.O.T u r n -o n T i m e t o n (m s )
Forward Current I F (mA)TURN-ON TIME vs. FORWARD CURRENT
Normalized to 1.0 at T A = 25 ?C,I F = 10 mA, V O = 5 V
100
0–25
2550752.53.00.02.0
1.51.00.5N o r m a l i z e d T u r n -o f f T i m e t o f f
Ambient Temperature T A (?C)
NORMALIZED TURN-OFF TIME vs.AMBIENT TEMPERATURE
N.C.
N.O.
T u r n -o f f T i m e t o f f (m s )
Forward Current I F (mA)
TURN-OFF TIME vs. FORWARD CURRENT
Normalized to 1.0 at T A = 25 ?C,I F = 10 mA, V O = 5 V
1000–25
2550752.53.00.02.01.51.00.5N o r m a l i z e d T u r n -o n T i m e t o n
Ambient Temperature T A (?C)NORMALIZED TURN-ON TIME vs.AMBIENT TEMPERATURE
N.C.
N.O.302520151050.2
0.60.81.2
0.41.00N.C.N.O.
V O = 5 V
Data Sheet PN10280EJ01V1DS
8
N u m b e r (p c s )
On-state Resistance R on (?)ON-STATE RESISTANCE (N.O.)DISTRIBUTION
N u m b e r (p c s )
On-state Resistance R on (?)
ON-STATE RESISTANCE (N.C.)
DISTRIBUTION
N u m b e r (p c s )
Turn-on Time t on (ms)TURN-ON TIME (N.O.) DISTRIBUTION
N u m b e r (p c s )
Turn-off Time t off (ms)TURN-OFF TIME (N.O.) DISTRIBUTION
N u m b e r (p c s )
Turn-on Time t on (ms)
TURN-ON TIME (N.C.) DISTRIBUTION
N u m b e r (p c s )
Turn-off Time t off (ms)
TURN-OFF TIME (N.C.) DISTRIBUTION
Remark The graphs indicate nominal characteristics.
Data Sheet PN10280EJ01V1DS 9
TAPING SPECIFICATIONS (in millimeters)
10
Data Sheet PN10280EJ01V1DS
RECOMMENDED SOLDERING CONDITIONS
(1) Infrared reflow soldering ? Peak reflow temperature 260°C or below (package surface temperature) ? Time of peak reflow temperature 10 seconds or less ? Time of temperature higher than 220°C 60 seconds or less ? Time to preheat temperature from 120 to 180°C 120±30 s
? Number of reflows Three
? Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.)
P a c k a g e S u r f a c e T e m p e r a t u r e T (?C )
Time (s)
Recommended Temperature Profile of Infrared Reflow
(2) Wave soldering ? Temperature 260°C or below (molten solder temperature) ? Time
10 seconds or less
? Preheating conditions 120°C or below (package surface temperature) ? Number of times One
? Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.)
(3) Cautions ? Fluxes
Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
Data Sheet PN10280EJ01V1DS 11
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE.
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information.
Restricted Substance
per RoHS Concentration Limit per RoHS
(values are not yet fixed)
Concentration contained
in CEL devices
-A -AZ
Lead (Pb) < 1000 PPM
Not Detected (*) Mercury < 1000 PPM Not Detected
Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected
PBB < 1000 PPM Not Detected
PBDE < 1000 PPM Not Detected
If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.