74HC05中文资料
1/8
July 2001s
HIGH SPEED:
t PD = 10ns (TYP .) at V CC = 6V s
LOW POWER DISSIPATION:I CC = 1μA(MAX.) at T A =25°C s
HIGH NOISE IMMUNITY:
V NIH = V NIL = 28 % V CC (MIN.)
s
WIDE OPERATING VOLTAGE RANGE:V CC (OPR) = 2V to 6V
s
PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 05
DESCRIPTION
The M74HC05 is an high speed CMOS HEX INVERTER (OPEN DRAIN) fabricated with silicon gate C 2MOS technology.
The internal circuit is composed of 3 stages including buffer output, which enables high noise immunity and stable output.
All inputs are equipped with protection circuits against static discharge and transient excess voltage.
M74HC05
HEX INVERTER (OPEN DRAIN)
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
PACKAGE TUBE T & R DIP M74HC05B1R SOP M74HC05M1R
M74HC05RM13TR TSSOP
M74HC05TTR
M74HC05
2/8
INPUT AND OUTPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
TRUTH TABLE
Z : High Impedance
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
PIN No SYMBOL NAME AND FUNCTION 1, 3, 5, 9, 11,
13
1A to 6A Data Inputs 2, 4, 6, 8, 10,
121Y to 6Y Data Outputs 7
GND Ground (0V)
14
V CC
Positive Supply Voltage
A Y L Z H
L
Symbol Parameter
Value Unit V CC Supply Voltage -0.5 to +7V V I DC Input Voltage -0.5 to V CC + 0.5V V O DC Output Voltage -0.5 to V CC + 0.5
V I IK DC Input Diode Current ± 20mA I OK DC Output Diode Current ± 20mA I O
DC Output Current
± 25mA I CC or I GND DC V CC or Ground Current
± 50mA P D Power Dissipation
500(*)mW T stg Storage Temperature -65 to +150
°C T L
Lead Temperature (10 sec)
300
°C
Symbol Parameter
Value Unit V CC Supply Voltage 2 to 6V V I Input Voltage 0 to V CC V V O Output Voltage 0 to V CC V T op Operating Temperature -55 to 125°C t r , t f
Input Rise and Fall Time
V CC = 2.0V 0 to 1000ns V CC = 4.5V 0 to 500ns V CC = 6.0V
0 to 400
ns
M74HC05
3/8
DC SPECIFICATIONS
AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = t f = 6ns)
Symbol
Parameter
Test Condition
Value Unit
V CC (V)T A = 25°C -40 to 85°C -55 to 125°C Min.Typ.
Max.
Min.Max.
Min.Max.
V IH
High Level Input Voltage
2.0 1.5 1.5 1.5V 4.5
3.15 3.15 3.156.0
4.2
4.2
4.2
V IL
Low Level Input Voltage
2.00.50.50.5V
4.5 1.35 1.35 1.356.0 1.8
1.8 1.8V OL
Low Level Output Voltage
2.0I O =20 μA 0.00.10.10.1V
4.5I O =20 μA 0.00.10.10.16.0I O =20 μA 0.00.10.10.14.5I O =4.0 mA 0.170.260.330.406.0
I O =5.2 mA 0.18
0.260.330.40I I Input Leakage Current
6.0V I = V CC or GND ± 0.1± 1± 1μA I OZ Output Leakage Current
6.0V I = V IH or V IL V O = V CC or GND ±0.5± 5± 10μA I CC
Quiescent Supply Current
6.0
V I = V CC or GND
1
1020
μA Symbol
Parameter
Test Condition
Value Unit
V CC (V)T A = 25°C -40 to 85°C -55 to 125°C Min.
Typ.Max.Min.
Max.Min.
Max.t THL
Output Transition Time
2.0307595110ns 4.581519226.07131619t PLZ
Propagation Delay Time
2.0R L = 1 K ?
2090115135ns
4.5111823276.010152023t PZL
Propagation Delay Time
2.0R L = 1 K ?
3390115135ns
4.591823276.0
8
15
20
23
M74HC05
CAPACITIVE CHARACTERISTICS
1) C PD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I CC(opr) = C PD x V CC x f IN + I CC /6 (per gate)
TEST CIRCUIT
L R T = Z OUT of pulse generator (typically 50?)
WAVEFORM : PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle)
Symbol
Parameter
Test Condition
Value Unit
V CC (V)T A = 25°C -40 to 85°C -55 to 125°C Min.
Typ.Max.Min.
Max.Min.
Max.C IN Input Capacitance 5.0510
10
10
pF C OUT Output
Capacitance
5.010pF C PD
Power Dissipation Capacitance (note 1)
5.0
6.5
pF
M74HC05
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
? The ST logo is a registered trademark of STMicroelectronics
? 2001 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom
? https://www.wendangku.net/doc/bc4133085.html,
8/8