当前位置：文档库 › 组件生产流程中英文对照

组件生产流程中英文对照

太阳能电池组件生产流程英文解说

中文：太阳能电池组件生产工艺

组件线又叫封装线，封装是太阳能电池生产中的关键步骤，没有良好的封装工艺，多好的电池也生产不出好的组件板。电池的封装不仅可以使电池的寿命得到保证，而且还增强了电池的抗击强度。产品的高质量和高寿命是赢得可客户满意的关键，所以组件板的封装质量非常重要。

工艺流程如下：

1、电池检测——

2、正面焊接—检验—

3、背面串接—检验—

4、敷设（玻璃清洗、材料切割、玻璃预处理、敷设）——

5、层压——

6、去毛边（去边、清洗）——

7、装边框（涂胶、装角键、冲孔、装框、擦洗余胶）——

8、焊接接线盒——

9、高压测试——10、组件测试—外观检验—11、包装入库；

1.2工艺简介：

在这里只简单的介绍一下工艺的作用，给大家一个感性的认识，具体内容后面再详细介绍：

1、电池测试：由于电池片制作条件的随机性，生产出来的电池性能不尽相同，所以为了有效的将性能一致或相近的电池组合在一起，所以应根据其性能参数进行分类；电池测试即通过测试电池的输出参数（电流和电压）的大小对其进行分类。以提高电池的利用率，做出质量合格的电池组件。

2、正面焊接：是将汇流带焊接到电池正面（负极）的主栅线上，汇流带为镀锡的铜带，我们使用的焊接机可以将焊带以多点的形式点焊在主栅线上。焊接用的热源为一个红外灯（利用红外线的热效应）。焊带的长度约为电池边长的2倍。多出的焊带在背面焊接时与后面的电池片的背面电极相连。(我们公司采用的是手工焊接)

3、背面串接：背面焊接是将36片电池串接在一起形成一个组件串，我们目前采用的工艺是手动的，电池的定位主要靠一个膜具板，上面有36个放置电池片的凹槽，槽的大小和电池的大小相对应，槽的位置已经设计好，不同规格的组件使用不同的模板，操作者使用电烙铁和焊锡丝将“前面电池”的正面电极（负极）焊接到“后面电池”的背面电极（正极）上，这样依次将36片串接在一起并在组件串的正负极焊接出引线。

4、层压敷设：背面串接好且经过检验合格后，将组件串、玻璃和切割好的EVA 、玻璃纤维、背板按照一定的层次敷设好，准备层压。玻璃事先涂一层试剂（primer）以增加玻璃和EVA的粘接强度。敷设时保证电池串与玻璃等材料的相对位置，调整好电池间的距离，为层压打好基础。（敷设层次：由下向上：玻璃、EVA、电池、EVA、玻璃纤维、背板）。

5、组件层压：将敷设好的电池放入层压机内，通过抽真空将组件内的空气抽出，然后加热使EVA熔化将电池、玻璃和背板粘接在一起；最后冷却取出组件。层压工艺是组件生产的关键一步，层压温度层压时间根据EVA的性质决定。我们使用快速固化EVA时，层压循环时间约为25分钟。固化温度为150℃。

6、修边：层压时EVA熔化后由于压力而向外延伸固化形成毛边，所以层压完毕应将其切除。

7、装框：类似与给玻璃装一个镜框；给玻璃组件装铝框，增加组件的强度，进一步的密封电池组件，延长电池的使用寿命。边框和玻璃组件的缝隙用硅酮树脂填充。各边框间用角键连接。

8、焊接接线盒：在组件背面引线处焊接一个盒子，以利于电池与其他设备或电池间的连接。

9、高压测试：高压测试是指在组件边框和电极引线间施加一定的电压，测试组件的耐压性和绝缘强度，以保证组件在恶劣的自然条件（雷击等）下不被损坏。

10、组件测试：测试的目的是对电池的输出功率进行标定，测试其输出特性，确定组件的质量等级。

英文：

Solar cell module production process

Line called packaging line components, packaging is the production of solar ce lls a key step in the packaging process without a good, multi-well battery is also not a good component of production boards. Battery package not only the battery life is guaranteed, but also to enhance the combat strength of the battery. Product quality and high service life is to win can be the key to customer satisfaction, so the quality of components of the package board is very important.

Process is as follows:

1, the battery test - 2, positive Welding - Inspection -3, on the back of cascading - Inspection -4, laying (glass cleaning, material cutting, glass pre-processing, laying) - 5, laminating - 6, to flash ( to the side, cleaning) - 7, fitted border (glue, loading angle keys, punching, install box, scrub I glue) - 8, the welding junction box - 9, high-pressure test - 10, component testing -- -11 appearance inspection, packaging and storage;

1.2 Process Description:

Here only a brief look at the role of technology, give us an emotional understanding of the specific content of a further detail later:

1, the battery test: Because the randomness of the battery-chip manufacturing conditions, the production out of battery performance is different, we will be for the effective performance of identical or similar battery together, it should be classified according to their performance parameters; battery test that is by testing the battery output parameters (current and voltage) of the size of its classification. To improve the utilization of the battery to make the battery components of acceptable quality.

2, positive welding: It's convergence with soldered to the battery positive (negative) of the main gate line, convergence zone for the tinned copper strip, we use a welding machine can weld with a

multi-point in the form of spot welding on the main gate Online. Welding heat source for an infrared lamp (using infrared thermal effect). Welding with the length of the side length of about 2 times the battery. More welding belt behind the back of welding with electrodes connected to the back of the battery piece. (Our company uses a manual welding)

3, on the back of concatenation: back of the weld is 36 cells cascaded together to form a component of the string, we are currently used process is manual, the battery depends mainly on the positioning of a membrane with plate 36 placed above the battery film grooves, groove size and battery size correspond to the location of tank has been designed well, different specifications of the components use a different template, the operator use electric soldering iron and solder wire will "in front of the battery," the positive electrode (cathode) Welding to the "behind the battery" on the back electrode (cathode), so that in turn will be 36 series with the component string together and welded out of positive and negative leads.

4, laminated lay: on the back of a good tandem and tested after passing the component string, glass and cut a good EVA, glass fiber, backplane according to a certain level, laying a good preparation for lamination. Glass pre-coated layer of reagent (primer) in order to increase the bonding strength of glass and EVA. When installed to ensure the battery strings and glass and other materials relative position, adjusting the distance between the battery, in order to laminate lay a solid foundation. (Laying of levels: from the bottom up: glass, EVA, cell, EVA, glass fiber, backplane).

5, component lamination: a good battery will be laid into the laminating machine, through the vacuum component of the air out, and then heated to melt the EVA batteries, glass and back bonding together; the final cooling out components. Lamination process is a key step in component production, lamination temperature lamination time, according to the nature of EVA. We use the

fast-curing EVA, the lamination cycle time is about 25 minutes. Curing temperature of 150 ℃.

6, trimming: laminated EVA melt when the pressure of reaching out after curing due to the formation of flash, so it should be removed laminated finish.

7, fitted box: similar to the glass mounted to a frame; to the glass component mounted aluminum frame to increase the intensity of the component, further sealing the battery components, longer battery life. Borders and glass components of the gap filled with silicone resin. The border between the connection with the angle button.

8, the welding junction box: In the component lead at the back of a box welded to facilitate the battery and other equipment or connections between cells.

9, high-pressure test: high-pressure test is defined as components of the border and the electrode lead a certain voltage is applied between the test component of the pressure resistance and dielectric strength to ensure that components in harsh natural conditions (lightning, etc.) will not be damaged under the .

10, component testing: the test objective is to calibrate the battery output power to test its output characteristics, determine the quality grade components.

机械零部件中英文对照

常用机械零部件中英文对照天轴line shaft 可倾瓦块轴承tilting-pad bearing 成型填料密封shaped packing seal 曲轴crank shaft 自润滑轴承self-lubricating bearing 含油轴承oil-impregnated bearing 制动功率braking power 板弹簧leaf spring 油(气)膜振盪oil/gas whip 空气弹簧air spring 花键联接spline joint 活塞环piston ring 飞轮fly wheel 径向滑动轴承journal bearing 气体轴承gas bearing 浮环密封floating ring seal 粉末冶金轴承powder metallurgy bearing 迷宫密封labyrinth seal 带式制动器band brake 推力滑动轴承thrust bearing 液体动压轴承hydrodynamic bearing

液体静压轴承hydrostatic bearing 焊接welding 球轴承ball bearing 连桿link 嵌入离合器jaw clucth 胀圈密封piston ring seal 超越离合器overrunning clutch 塔轮step pulley 填料函密封packing box seal 块式制动器shoe brake 楔联接wedge joint 滑动轴承材料sliding bearing material 滑轮pulley 万向联轴器universal coupling 游丝hairspring 过盈配合联接interference fit joint 铆接riveted joint 电磁制动器electromagnetic brake 电磁轴承electromagnetic bearing 槓桿ganggan 滚子轴承roller bearing 滚针轴承needle bearing

汽车零部件中英文对照表

汽车类Automobile English 整车Finished Automobile 轿车Passenger Car 休旅车Recreational Vehicle (RV) 小型商用车(3.5吨以下) Light Duty Commercial Car (Less Than 3.5 Tons) 大型商用车(3.5吨以上) Heavy Duty Commercial Car (More Than 3.5 Tons) 散装车Bulk Truck 搅拌车Mixer Truck 环境卫生车Garbage Truck 液罐车Refueling Truck 倾卸车Dumper Truck 曳引车Tractor Truck 消防车Fire Fighting Truck 堆高机Forklift 拖板车Pallet Truck 运钞车Armor Cash Carrier 冷气客车Air-Conditioned Car 冷冻车Freezer Car 拖车Trailer 车体打造(改装) Car Body Building (Refitting) 瓦斯车LPG Car 底盘车Chasis Truck 引擎零件Engine Parts 引擎Engine 引擎波司Engine Bush 引擎修理包Engine Gasket Kits 引擎零件Engine Parts 凸轮轴Camshaft 凸轮轴链轮Sprocket Camshaft 皮带张力器Tensioner 曲轴Crankshaft 曲轴皮带盘Crankshaft Pulley 曲轴轴承片Crankshaft Bearing 汽门Valve 汽门座Valve Seat 汽门摇臂Valve Arm 汽门摇臂盖Rocker Cover 汽门弹簧Valve Spring 汽门导管Valve Guide 汽缸头(盖) Cylinder Head 汽缸衬套Cylinder Liner 汽缸体Cylinder Block 波司垫片Washer 活塞Piston 活塞肖Piston Pin 活塞环Piston Ring 活塞衬套Piston Liner 飞轮Flywheel 飞轮环齿轮Ring Gear of Flywheel 时规炼条/皮带Timing Chain/Belt 连杆Connecting Rod 连杆轴承片Connecting Rod Bearing 摇臂轴Rocker Arm Shaft 汽门锁Valve Cotter 止推垫片Thrust Washer 共鸣箱Resonator 喷油嘴Injection Nozzle 燃料系统Fueling System 油箱Fuel Tank 油箱浮筒Gauge Fuel Tank 空气滤清器Air Cleaner 空气滤清器盖Air Cleaner Cover 空气滤清器导管Air Intake Tube 空气滤蕊Air Cleaner Element 消音器Exhaust Muffler 排气歧管Exhaust Manifold 排气管Exhaust Pipe 进气歧管Intake Manifold

电子元件中英文对照

一．电子元器件 Electronic Components 1．保险元器件safety device （1） fuse block （2） current fuse （3） other （4） temperature fuse （5） temperature switches （6） since the resumption of fuse 2. 变频器transducer （1） PLC transducer （2）High-performance Universal transducer （3）Constant Power Inverter （4）Constant Torque converter （5）Exclusive Inverter 3.变压器transformer

（1）Power Transformer （2）the isolation transformer （3）constant voltage transformer （4）pulse transformer （5）other transformers （6）Audio transformers （7）autotransformer （8）coupling transformer 4.场效应管voltage controller 5. 传感器sensor （1）Power Transformer （2）Photoelectric Sensors （3）Fiber Optic Sensors （4）Accelerometer （5）Proximity sensor

（6）Level, liquid level sensor （7）Pressure Sensor （8）Vibration Sensor （9）Gas Sensor （10）Acoustic sensor （11）Visual, image sensor （12）Moisture and humidity sensor （13）Displacement sensor （14）传感器Sensor sensor 6.传声器microphone 7.电容器capacitor （1）Glass capacitors （2）Glazed glass capacitors （3）Composite Dielectric Capacitors （4）Electrolytic capacitors

汽车零件中英文对照表

汽车、汽车零部件、配件中英文对照表汽车类 Automobile English 整车 Finished Automobile 轿车 Passenger Car 休旅车 Recreational Vehicle (RV) 小型商用车(3.5吨以下) Light Duty Commercial Car (Less Than 3.5 Tons) 大型商用车(3.5吨以上) Heavy Duty Commercial Car (More Than 3.5 Tons) 散装车 Bulk Truck 搅拌车 Mixer Truck 环境卫生车 Garbage Truck 液罐车 Refueling Truck 倾卸车 Dumper Truck 曳引车 Tractor Truck 消防车 Fire Fighting Truck 堆高机 Forklift 拖板车 Pallet Truck 运钞车 Armor Cash Carrier 冷气客车 Air-Conditioned Car 冷冻车 Freezer Car

拖车 Trailer 车体打造(改装) Car Body Building (Refitting) 瓦斯车 LPG Car 底盘车 Chasis Truck 引擎零件 Engine Parts 引擎 Engine 引擎波司 Engine Bush 引擎修理包 Engine Gasket Kits 引擎零件 Engine Parts 凸轮轴 Camshaft 凸轮轴链轮 Sprocket Camshaft 皮带张力器 Tensioner 曲轴 Crankshaft 曲轴皮带盘 Crankshaft Pulley 曲轴轴承片 Crankshaft Bearing 汽门 Valve 汽门座 Valve Seat 汽门摇臂 Valve Arm 汽门摇臂盖 Rocker Cover 汽门弹簧 Valve Spring 汽门导管 Valve Guide 汽缸头(盖) Cylinder Head

盘式制动器中英文对照外文翻译文献

中英文对照外文翻译文献 (文档含英文原文和中文翻译) 外文： An Experimental Analysis of Brake Efficiency Using four Fluids in a Disc Brake System ABSTRACT The paper studies disc brake failure in Mini-buses using an experimental analysis to test the maximum braking force when different brake fluids such as clean, less dirty, dirty and soapy water solution were used in the braking system. The experimental results clearly showed that the soap solution appears to be the best fluid as far as low viscosity and stability of viscosity with increase in temperature are concerned. However, the soap solution is not compatible with other fluid which makes it difficult to be substitute as a clean brake fluid. The result of the Thepra Universal Brake Testing Equipment used for the braking efficiency test indicated that a pedal brake of 117 kN produce a brake force of 0.96 kN for clean brake fluid, 0.91 kN for the less dirty, 0.85 kN for dirty and 1.44 kN for

汽车零部件中英文对照

汽车零部件中英文对照车轮系统Wheeling System 轮毂Wheel Hub 轮胎Tire 轮胎汽门嘴Tire Valve 轮圈Wheel Disk 轮圈盖Wheel Cover 内胎（含内衬）Inner Tire (Flap) 车轮系统Wheeling System 电装品 Electrical Parts 电瓶Battery 中央门控Central Door Lock 分电盘Distributor 火星塞Spark Plug 汽车用电子钟Digital Clock 汽车音响Car Audio 防盗器Car Burglar Alarm 雨刷及雨刷连 Wiper / Linkage 杆保险丝座 Fuse Seat 保险丝Fuse

配线Wire Harness 马达类Motor 高压线组Ignition Cable 喇叭Horn 发电机（零件）Alternator (Components) 开关类Switch 蜂鸣器Buzzer 预热塞Glow Plug 仪表Combination Meter 灯泡Bulb 灯类Lamp 点火线圈Ignition Coil 继电器Relay 倒车雷达Reverse Sensor 电池充电器Battery Charger 闪光器Flasher 省电器Energy Saving Unit 端子Terminal 电动座椅装置Power Seat Unit 马达零件Motor Components

电装品Electrical Parts

汽车用光盘Car CD 汽车用液晶显示器Car LCD 调整器Regulator 整流器Rectifier 电子点火器Ignition Module 倒车显示器Rear View Display 定速器Cruise Controller HID车灯安定器组合HID Ballast Complete Set LED 灯LED Lamp 车灯控制器Lighting Controller 点火线圈模块Ignition Coil Module 外装品Exterior Parts 水箱饰罩Radiator Grille 天线Antenna 车身护条Side Protector 防撞护垫Bumper Pad 后视镜Door Mirror for Headlights 挡泥板Mud Guard 扰流板Spoiler 装饰贴纸、标

元器件中英文对照

proteus元件库介绍 AND 与门 ANTENNA 天线BATTERY 直流电源 BELL 铃,钟 BVC 同轴电缆接插件BRIDGE 1 整流桥(二极管) BRIDGE 2 整流桥(集成块) BUFFER 缓冲器BUZZER 蜂鸣器 CAP 电容 CAPACITOR 电容CAPACITOR POL 有极性电容CAPVAR 可调电容CIRCUIT BREAKER 熔断丝COAX 同轴电缆 CON 插口 CRYSTAL 晶体振荡器 DB 并行插口 DIODE 二极管 DIODE SCHOTTKY 稳压二极管DIODE VARACTOR 变容二极管

DPY_3-SEG 3段LED DPY_7-SEG 7段LED DPY_7-SEG_DP 7段LED(带小数点) ELECTRO 电解电容 FUSE 熔断器 INDUCTOR 电感 INDUCTOR IRON 带铁芯电感INDUCTOR3 可调电感 JFET N N沟道场效应管 JFET P P沟道场效应管 LAMP 灯泡 LAMP NEDN 起辉器 LED 发光二极管 METER 仪表MICROPHONE 麦克风 MOSFET MOS管 MOTOR AC 交流电机 MOTOR SERVO 伺服电机 NAND 与非门 NOR 或非门 NOT 非门 NPN NPN三极管

NPN-PHOTO 感光三极管OPAMP 运放 OR 或门 PHOTO 感光二极管 PNP 三极管 NPN DAR NPN三极管PNP DAR PNP三极管 POT 滑线变阻器 PELAY-DPDT 双刀双掷继电器RES1.2 电阻 RES3.4 可变电阻RESISTOR BRIDGE ? 桥式电阻RESPACK ? 电阻 SCR 晶闸管 PLUG ? 插头 PLUG AC FEMALE 三相交流插头SOCKET ? 插座 SOURCE CURRENT 电流源SOURCE VOLTAGE 电压源SPEAKER 扬声器 SW ? 开关 SW-DPDY ? 双刀双掷开关

部分汽车零部件中英文对照

部分汽车零部件中英文对照 1上连杆瓦：Upper Connecting Rod Bush 2下连杆瓦：Lower Connecting Rod Bush 3喷油泵柱塞偶件：Pump PMP（Plunger and Bare of Injection Pump）4斯太尔飞轮齿圈Styer Flywheel Ring Gear 5曲轴瓦Crankshaft Bearing 6曲轴止推片Crankshaft Thrust Bearing 7联轴器钢片总成Shaft Joint Assembly 8偏心瓦Eccentric Bush 9高压油泵修理包High-pressure Fuel Injection Pump Repair Kit 10油底壳垫子Oil Pan Gasket 11全车垫子full-car Gasket 12活塞连杆Piston-rod 13缸盖垫子Cylinder Head Gasket 14排气管垫子Exhaust Pipe Gasket 15 连杆套Connecting Rod Bushing 16活塞连杆固定螺栓Piston-rod Fixed Stud 17缸盖螺栓Cylinder Head Bolt 18增压器Supercharger 19增压器Supercharger 20水泵Water Pump 21机油泵Oil Pump 22熄火开关Shut-off Switch

23高压油管280 High-pressure Oil Tube 280 24高压燃油管High Pressure Oil Fuel Pipe 25高压油管（直）High-pressure Oil Tube (straight) 26回油管Oil Return Pipe 27机油软管（短）Engine Oil Rubber Hose (short) 28机油软管（长）Engine Oil Rubber Hose (long) 29燃油管（从油箱到燃油）Fuel Pipe (from the tank to the fuel) 1. Cylinder Block 气缸体 2. Cylinder Liner 气缸套 3. Cylinder Head 气缸盖 4. Cylinder Head Gasket 气缸盖垫 5. Cylinder Head Fasteners 气缸盖螺栓 6. Cylinder Head Cover Gasket 气缸盖罩衬垫 7. Cylinder Head Cover 气缸盖罩 8. Pistons 活塞 9. Piston Pin 活塞销 10. Piston Ring Set 活塞环组 11. Cranks Haft 曲轴 12. Crankshaft Bearing 曲轴轴瓦 13. Camshaft 凸轮轴 14. Camshaft Sprocket 凸轮轴齿形皮带轮 15. Camshaft Bearings 凸轮轴轴承 16. Tappet 挺杆

汽车制动器论文中英文对照资料外文翻译文献

毕业设计（论文）外文翻译 AUTOMOTIWE FINAL DRIVE FINAL DRIVE A final drive is that part of a power transmission system between the drive shaft and the differential. Its function is to change the direction of the power transmitted by the drive shaft through 90 degrees to the driving axles. At the same time. it provides a fixed reduction between the speed of the drive shaft and the axle driving the wheels. The reduction or gear ratio of the final drive is determined by dividing the number of teeth on the ring gear by the number of teeth on the pinion gear. In passenger vehicles, this speed reduction varies from about 3:1 to 5:1. In trucks it varies from about 5:1 to 11:1. To calculate rear axle ratio, count the number of teeth on each gear. Then divide the number of pinion teeth into the number of ring gear teeth. For example, if the pinion gear has 10 teeth and the ring gear has 30 (30 divided by 10), the rear axle ratio would be 3:1. Manufacturers install a rear axle ratio that provides a compromise between performance and economy. The average passenger car ratio is 3.50:1. The higher axle ratio, 4.11:1 for instance, would increase acceleration and pulling power but would decrease fuel economy. The engine would have to run at a higher rpm to maintain an equal cruising speed. The lower axle ratio. 3:1, would reduce acceleration and

部分汽车零部件中英文对照

电子元件中英文对照

一．电子元器件Electronic Components 1．保险元器件safety device （1）保险丝座 fuse block （2）电流保险丝 current fuse （3）其他保险元器件 other （4）温度保险丝 temperature fuse （5）温度开关 temperature switches （6）自恢复熔断器since the resumption of fuse 2. 变频器transducer （1）PLC 变频器 PLC transducer （2）高性能通用变频器High-performance Universal transducer （3）恒功率变频器Constant Power Inverter （4）恒转矩变频器Constant Torque converter （5）专用变频器Exclusive Inverter 3.变压器transformer （1）电源变压器Power Transformer （2）隔离变压器the isolation transformer （3）恒压变压器constant voltage transformer （4）脉冲变压器pulse transformer （5）其他变压器other transformers （6）音频变压器Audio transformers （7）自耦变压器autotransformer （8）耦合变压器coupling transformer 4.场效应管voltage controller 5. 传感器sensor （1）电磁传感器Power Transformer （2）光电传感器Photoelectric Sensors （3）光纤传感器Fiber Optic Sensors （4）加速度传感器Accelerometer （5）接近传感器Proximity sensor （6）料位、液位传感器Level, liquid level sensor （7）压力传感器Pressure Sensor （8）振动传感器Vibration Sensor （9）气体传感器Gas Sensor （10）声波传感器Acoustic sensor （11）视觉、图像传感器Visual, image sensor （12）水分、湿度传感器Moisture and humidity sensor （13）位移传感器Displacement sensor （14）敏感元件传感器Sensor sensor 6.传声器microphone 7.电容器capacitor （1）玻璃电容器Glass capacitors （2）玻璃釉电容器Glazed glass capacitors （3）复合介质电容器Composite Dielectric Capacitors

Cadence常用器件中英文对照表

Proteus常用器件中英文对照表AND 与门 ANTENNA 天线 BATTERY 直流电源 BELL 铃,钟 BVC 同轴电缆接插件 BRIDEG 1 整流桥(二极管) BRIDEG 2 整流桥(集成块) BUFFER 缓冲器 BUZZER 蜂鸣器 CAP 电容 CAPACITOR 电容 CAPACITOR POL 有极性电容CAPV AR 可调电容 CIRCUIT BREAKER 熔断丝 COAX 同轴电缆 CON 插口 CRYSTAL 晶振 DB 并行插口 DIODE 二极管 DIODE SCHOTTKY 稳压二极管

DIODE V ARACTOR 变容二极管DPY_3-SEG 3段LED DPY_7-SEG 7段LED DPY_7-SEG_DP 7段LED(带小数点) ELECTRO 电解电容 FUSE 熔断器 INDUCTOR 电感 INDUCTOR IRON 带铁芯电感INDUCTOR3 可调电感 JFET N N沟道场效应管 JFET P P沟道场效应管 LAMP 灯泡 LAMP NEDN 起辉器 LED 发光二极管 METER 仪表 MICROPHONE 麦克风 MOSFET MOS管 MOTOR AC 交流电机 MOTOR SERVO 伺服电机 NAND 与非门 NOR 或非门 NOT 非门

NPN NPN三极管 NPN-PHOTO 感光三极管OPAMP 运放 OR 或门 PHOTO 感光二极管 PNP 三极管 NPN DAR NPN三极管 PNP DAR PNP三极管 POT 滑线变阻器 PELAY-DPDT 双刀双掷继电器RES1.2 电阻 RES3.4 可变电阻 RESISTOR BRIDGE ? 桥式电阻RESPACK ? 电阻 SCR 晶闸管 PLUG ? 插头 PLUG AC FEMALE 三相交流插头SOCKET ? 插座 SOURCE CURRENT 电流源SOURCE VOLTAGE 电压源SPEAKER 扬声器

proteus常用元件中英文对照表

proteus常用元件中英文对照表元件名称中文名说明 7407 驱动门 1N914 二极管 1N4735 稳压二极管 74Ls00 与非门 74LS04 非门 74LS08 与门 74LS390 TTL 双十进制计数器 7SEG 4针BCD-LED 输出从0-9 对应于4根线的BCD码 7SEG 3-8译码器电路BCD-7SEG转换电路 ALTERNATOR 交流发电机 AMMETER-MILLI mA安培计 AND 与门 1N4735 稳压二极管 BA TTERY电池/电池组 BUS 总线 CAP 电容 CAPACITOR 电容器 CLOCK 时钟信号源 CRYSTAL 晶振 D-FLIPFLOP D触发器 FUSE 保险丝 GROUND地 LAMP 灯 LED-RED 红色发光二极管 LM016L 2行16列液晶可显示2行16列英文字符，有8位数据总线D0-D7，RS，R/W，EN三个控制端口（共14线），工作电压为5V。没背光，和常用的1602B功能和引脚一样（除了调背光的二个线脚） LOGIC ANAL YSER 逻辑分析器 LOGICPROBE 逻辑探针 LOGICPROBE[BIG] 逻辑探针用来显示连接位置的逻辑状态 LOGICSTATE 逻辑状态用鼠标点击,可改变该方框连接位置的逻辑状态LOGICTOGGLE 逻辑触发 MASTERSWITCH 按钮手动闭合,立即自动打开 MOTOR 马达 OR 或门 POT-LIN 三引线可变电阻器 POWER电源 RES 电阻 POT-LIN 可变电阻 RESISTOR电阻 SWITCH 按钮手动按一下一个状态 SWITCH-SPDT 二选通一按钮 VOLTMETER 伏特计

制动器零件中英文对照讲解学习

CE-1 FRT BRAKE[breik]ASS'Y - LH/RH 前左/右转向节带盘式制动器轮毂总成KNUCKLE['n?kl]ASS'Y WITH HUB[h?b]BEARING['bε?ri?]- LH/RH 左/右转向节带轮毂总成 KNUCKLE M/C - LH/RH左/右转向节 KNUCKLE CASTING['kɑ:sti?]- LH/RH左/右转向节毛坯 BEARING - 1ST GEN双列球轴承 CIRCLIP ['s?:klip] 孔用弹性挡圈 HUB FLANGE[fl?nd?] 前轮毂 WHEEL[hwi:l] MT'G BOLT[b?ult] 前轮毂螺栓 SPLASH[spl??]SHIELD[?i:ld] 前防溅罩 BOLT - D/COVER 六角梅花头组合螺栓M6×14 DISC[disk] M/C 前制动盘 FLANGE BOLT 支架安装螺栓M12×1.25×28 FRT. CALIPER ['k?lip?(r)] ASS'Y-LH/RH 前左/右制动钳总成CYLINDER['silind?] M/C [PLATING['pleiti?]] -LH/RH 前左/右制动钳体CYLINDER CAST'G [PLATING] - LH/RH 前左/右制动钳体毛坯 BOOT[bu:t]PISTON['pist?n] ASS'Y 前钳体活塞防尘罩 RIM[rim] - BOOT PISTON 骨架 BOOT PISTON前活塞防尘罩 SEAL[si:l]PISTON 前活塞密封圈 PISTON M/C 前钳体活塞 CARRIER['k?ri?] M/C [PLATING] 制动钳支架 CARRIER CASTING 制动钳支架毛坯 GUIDE[ɡaid] PILLAR['pil?] SHIELD[?i:ld] 导柱防尘盖 GUIDE PILLAR CUSHION['ku??n] COLLAR['k?l?] 导柱缓冲套 GUIDE ROD[r?d] 导柱

元器件中英文对照

p r o t e u s元件库介绍AND 与门 ANTENNA 天线 BATTERY 直流电源 BELL 铃,钟 BVC 同轴电缆接插件 BRIDGE 1 整流桥(二极管) BRIDGE 2 整流桥(集成块) BUFFER 缓冲器 BUZZER 蜂鸣器 DB LAMP 灯泡 LAMP NEDN 起辉器 LED 发光二极管 METER 仪表 MICROPHONE 麦克风 MOSFET MOS管 MOTOR AC 交流电机 MOTOR SERVO 伺服电机 NAND 与非门 NOR 或非门 NOT 非门

NPN NPN三极管 NPN-PHOTO 感光三极管 OPAMP 运放 OR 或门 PHOTO 感光二极管 PNP 三极管 NPN DAR NPN三极管 PNP DAR PNP三极管 POT 滑线变阻器 PELAY-DPDT 双刀双掷继电器 RES1.2 电阻 SW-PB 开关 7407 驱动门 1N914 二极管 74Ls00 与非门 74LS04 非门 74LS08 与门 74LS390 TTL 双十进制计数器 7SEG 4针BCD-LED 输出从0-9 对应于4根线的BCD码7SEG 3-8译码器电路BCD-7SEG转换电路ALTERNATOR 交流发电机

AMMETER-MILLI mA安培计 AND 与门 BATTERY 电池/电池组 BUS 总线 CAP 电容 CAPACITOR 电容器 CLOCK 时钟信号源 CRYSTAL 晶振 D-FLIPFLOP D触发器 FUSE 保险丝 GROUND 地 OR 5楼 VTERM 串行口终端 Electromechanical 电机 Inductors 变压器 Laplace Primitives 拉普拉斯变换 Memory Ics Microprocessor Ics Miscellaneous 各种器件 Modelling Primitives 各种仿真器件是典型的基本元器模拟，不表示具体型号，只用于仿真，没有PCB Optoelectronics 各种发光器件发光二极管，LED，液晶等等

proteus元件中英文对照表解析

1.analog ics 模拟集成器件8个子类： amplifier 放大器 comparators 比较器 display drivers 显示驱动器 filters 滤波器 miscellaneous 混杂器件 regulators 三端稳压器 timers 555定时器 voltage references 参考电压 2，capacitors CAP电容，23个分类别 animated 可显示充放电电荷电容 audio grade axial 音响专用电容 axial lead polypropene 径向轴引线聚丙烯电容 axial lead polystyrene 径向轴引线聚苯乙烯电容 ceramic disc 陶瓷圆片电容 decoupling disc 解耦圆片电容 high temp radial 高温径向电容 high temp axial electrolytic高温径向电解电容 metallised polyester film 金属聚酯膜电容 metallised polypropene 金属聚丙烯电容 metallised polypropene film 金属聚丙烯膜电容 miniture electrolytic 微型电解电容 multilayer metallised polyester film 多层金属聚酯膜电容mylar film 聚酯薄膜电容 nickel barrier 镍栅电容 non polarised 无极性电容 polyester layer 聚酯层电容 radial electrolytic 径向电解电容 resin dipped 树脂蚀刻电容 tantalum bead 钽珠电容 variable 可变电容 vx a xial electrolytic VX 轴电解电容 3，CMOS 4000 series 4000系列数字电路 adders 加法器 buffers & drivers 缓冲和驱动器 comparators 比较器 counters 计数器 decoders 译码器 encoders 编码器 flip-flops & latches 触发器和锁存器 frequency dividers & tiner 分频和定定时器 gates & inverters 门电路和反相器 memory 存储器

protues中常用原件中英对照

protues元件库中英文对照表7407 驱动门serial ports; serial port 1N914 二极管 74Ls00 与非门 74LS04 非门 74LS08 与门 74LS390 TTL 双十进制计数器 7SEG 4针BCD-LED 输出从0-9 对应于4根线的BCD码 7SEG 3-8译码器电路 BCD-7SEG转换电路 ALTERNATOR 交流发电机 AMMETER-MILLI mA安培计 AND 与门 BA TTERY 电池/电池组 BUS 总线 CAP 电容 CAPACITOR 电容器 CLOCK 时钟信号源 CRYSTAL 晶振 D-FLIPFLOP D触发器 FUSE 保险丝

GROUND 地 LAMP 灯 Traffic lights 交通灯 MATRIX 点阵 RESPACK 排阻 LED-RED 红色发光二极管 LM016L 2行16列液晶可显示2行16列英文字符，有8位数据总线D0-D7，RS，R/W，EN三个控制端口（共14线），工作电压为5V。没背光，和常用的1602B功能和引脚一样（除了调背光的二个线脚） LOGIC ANAL YSER 逻辑分析器 LOGICPROBE 逻辑探针 LOGICPROBE[BIG] 逻辑探针用来显示连接位置的逻辑状态 LOGICSTATE 逻辑状态用鼠标点击,可改变该方框连接位置的逻辑状态 LOGICTOGGLE 逻辑触发 MASTERSWITCH 按钮手动闭合,立即自动打开 MOTOR 马达 OR 或门 POT-LIN 三引线可变电阻器 POWER 电源 RES 电阻 RESISTOR 电阻器 SWITCH 按钮手动按一下一个状态 SWITCH-SPDT 二选通一按钮 VOLTMETER 伏特计 VOLTMETER-MILLI mV伏特计

汽车零部件中英文对照

仪表板Instrument Panel 中央置物箱Console 孔塞Grommet Plug 地毯Floor Mat 安全带Seat Belt 车门扶手Door Armrest 车门把手Door Handle 车门锁Door Lock 车顶内衬Roof Lining 车窗升降摇柄Window Lifter Handle 车窗升降机Window Lifter 防水衬条Weather strip 油量表Fuel Gauge 门饰板Door Trim 室内镜Room Mirror 音响喇叭盖Speaker Cover (电动)座椅(Electric) Seat 顶蓬Headlining 烟灰缸Ashtray 各类隔音垫All Kinds of Silencer 饰板/饰条Garnish / Trim 仪表饰板Instrument Panel Garnish 遮阳板Sun visor 压条Moulding 点烟器Cigar Lighter 备胎板Trim for Spare Tire 天窗Sun Roof 后置物板Rear Parcel Shelf 后舱室饰板Rear Trunk Trim 仪表板支架 Instrumental Panel Mounting 其它Others 随车工具Tools

千斤顶Jack 尼龙绳、特多龙绳Nylon Rope 生产、检测及涂装设备 Production, Test & Painting Equipment 各类孔盖Cap、Cover 扣具Cargo Lash 夹片、管束Clamp, Clip 油土与基准模型 Clay Model and Master Model 油封Oil Seal 门铰链Door Hinge 故障标志Reflector 玻璃类Glass 修理业Repairing & Maintenance 粉末冶金Powder Metallurgy 轴承Bearing 塑料件Plastic Parts 隔热材Heat Insulator 电子件Electrical Parts 垫片类 Seal、Gasket、Washer、Packing 碳刷Carbon Brush 管类Pipe, Hose, Tube 铜套类Bushing 弹簧Spring 橡胶件Rubber Parts 帮浦类Pump 螺帽/螺栓/螺丝Nut/Bolt/Screw 锻造件(加工) Forging Parts (Processing) 滤清器类Filter 锁Lock 镜类> Mirror