文档库

最新最全的文档下载
当前位置:文档库 > h3c 基本配置方法

h3c 基本配置方法

=========================================================================

#名字,时间配置

sysname R1

clock timezone GMT add 8

clock timezone UTC add 8

clock datetime 9:30:20 2001/02/08

#告警

header motd XXXXXXXXXXXXXXXXXXXXXXXXXXX

Please input banner content, and quit with the character 'X'.

X

#Telnet配置

telnet server enable

user-interface vty 0 4

authentication-mode password

set authentication password simple cisco

user privilege level 3

acl 2000 inbound

acl number 2000

rule 5 deny source 1.1.1.1 0

#Telnet配置实用用户名验证

telnet server enable

local-user user

service-type telnet level 3

password simple ciscocisco

user-interface vty 0 4

acl 2000 inbound

authentication-mode scheme

#保存配置文件

save

The current configuration will be written to the device. Are you sure? [Y/N]:y

Please input the file name(*.cfg)[flash:/startup.cfg]

(To leave the existing filename unchanged, press the enter key):

flash:/startup.cfg exists, overwrite? [Y/N]:y

dir

Directory of flash:/

0 drw- - Dec 25 2009 19:34:36 logfile

1 -rw- 1363 Feb 08 2001 18:06:13 startup.cfg

2 -rw- 47646 Feb 08 2001 17:38:37 default.diag

#清除保存的配置文件

reset saved-configuration

dir

Directory of flash:/

0 drw- - Dec 25 2009 19:34:36 logfile

1 -rw- 1363 Feb 08 2001 18:10:24 startup.cfg

2 -rw- 47646 Feb 08 2001 17:38:37 default.diag

3 -rw- 1363 Feb 08 2001 18:10:40 f1.cfg

2540 KB total (2448 KB free)

#设置下次启动配置文件

startup saved-configuration f1.cfg

Please wait ....... Done!

dis startup

Current startup saved-configuration file: flash:/startup.cfg Next startup saved-configuration file: flash:/f1.cfg

#利用tftp备份和还原配置文件

backup startup-configuration to xxxx

restore startup-configuration from xxxx

startup-conf=save-conf

running-config=curr-conf

tftp 1.1.1.1 ?

get Download file from remote TFTP server

put Upload local file to remote TFTP server

sget Download securely from remote TFTP server

[R1-Ethernet0/4/0]port link-mode ?

bridge Switch to layer2 ethernet

route Switch to layer3 ethernet

#设置启动镜像

boot-loader file flash:/xxx.bin

reboot

schedule reboot at 11:11

#打开调试

terminal debugging

un deb all

#配置vlan,并把端口加入vlan

[SW1]vlan 30

[SW1-vlan30]port Ethernet 0/4/5 to Ethernet 0/4/7

#trunk配置

int e0/4/2

port link-type trunk

port trunk permit vlan all

port trunk pvid vlan xxx //native vlan

#配置stp

stp enable

stp mode rstp

stp priority 4096

stp edged-port enable //portfast

stp bpdu-protection

#mst

stp region-configuration

region-name zxc

instance 1 vlan 10 30

instance 2 vlan 20

active region-configuration

[SW2]int e0/4/2

[SW2-Ethernet0/4/2]stp cost ?

INTEGER<1-200000> Port path cost

[SW2-Ethernet0/4/2]stp instance 1 cost ?

INTEGER<1-200000> Port path cost

#配置dot1x

[SW1]dot1x

802.1x is enabled globally.

dot1x interface e0/4/4 to Ethernet 0/4/5

[SW1]local-user user

New local user added.

[SW1-luser-user]service-type lan-access

[SW1-luser-user]password simple cicso

#端口隔离

port-isolate enable

port-isolate uplink-port

[SW1-Ethernet0/4/7]user-bind ip-address 1.1.1.1 mac-address 1111-1111-1111 #链路汇集

[SWA] interface bridge-aggregation 1

[SWA-Ethernet1/0/1] port link-aggregation group 1

[SWA-Ethernet1/0/2] port link-aggregation group 1

display link-aggregation summary