Data Sheet on Solder Paste
IDENTITY
ECOSOLDER P ASTE M705-GRN360-K2-V No Revision 031669 C
Section
Manufacturer'Name
Senju Metal Industry Co.,Ltd. T elephone Number for Information 03(3888)5152
Address
23,Senju-Hasido-cho,Adachi-ku,T okyo,JAP AN 120-8555 Data Prepared 7. Feb. 2005
Section Hazardous Ingredients/Identity Information
Hazardous Components CAS No. OSHA PEL ACGIH TL V % Tin 7440-31-5 2mg/m (8-hrTW A) 2mg/m (8-hrTW A) 80 - 90 *Current OSHA standard,and ACGIH(1980)Intended changes
List for tin,tin oxide,and inorganic compounds(except SnH4),as Sn.
STEL is for 4 mg/m
Silver 7440-22-4 0.01mg/m (8Hr-TW A) 0.1mg/m (8Hr-TW A) 1 - 4 Copper 7440-50-8 0.1mg/m (8Hr TW A) 0.2mg/m (8Hr TW A) <1
Rosin 65997-05-9 3 - 5 Diethylene glycol 112-59-4 4 - 6 Mono hexylether
Section Physical/Chemical Characteristics
Boiling Point
over 260 Specific Gravity (H
O=1)
4.5
V apor Pressure (mm Hg)
NA Melting Point ( )
ALLOYS 217 - 219
V apor Density (AIR=1)
NA Evaporation Rate
(Butyl Acetate=1) NA
Solubility in Water
Insoluble
Appearance and Odor
Amber viscous paste,mild ether-like. Section Fire and Explosion Hazard Data
Flash Point (Solvent used in this flux)
C.O.C 141 Flammable Limits LEL
---
UEL
---
Extinguishing Media
Carbon dioxide and/or dry chemical
Special Fire Fighting Procedures
Use self-contained breathing apparatus and full protective clothing for fires in enclosed areas . Unusual Fire and Explosion Hazards
Section Reactivity Data IDENTITY ECOSOLDERP ASTE M705-GRN360-K2-V
Unstable Stability
Stable
Conditions to A void
Keep away from heat,sparks and open flames.
Incompatibility Strong oxidizing materials,acids,hydrogen peroxide.
Hazardous Decomposition or Byproducts Rosin acids,CO,CO ,aliphatic aldehydes. May Occur
Conditions to A void NA
Hazardous Polymerization
Will Not Occur
Section Health Hazard Data Route of Entry : Inhalation Skin Ingestion Health Hazards
When heated,vapors can cause irritation to eyes,nose and throat.May cause headache.
Carcinogenicity : Not listed NTP IARC Monographs OHSA Regulated Signs and Symptoms of Exposure
Symptoms of the neurological effects may include irritability ,headaches,insomnia,delirium, convulsion,muscular tremors,and palsy of the extremities. Medical Conditions Generally Aggravated by Exposure
Emergency and First Aid Procedures
Inhalation : Excessive overexposure may result in an acute or chronic illness. If symptoms are present,the individual shoud be removed from exposure and a physician consulted. Ingestion : Call a physician at once.
Skin : For hot metal burns,exposed area shoud be cooled with water and get medical attention. After handling solder ,wash throughly with soap and water . Section Precautions for Safe Handling and Use Steps to Be Taken in Case Material is Released or Spilled
A void inhalation of solder fume or dust. V acuuming is recommended.
Waste Disposal Method
Contact supplier or a licensed chemical waste disposal contractor for treatment,packaging,and disposal requirements. Precautions to Be Taken in Handling and Storing
A void breathing smoke during soldering. Wash hands before eating or smoking after handing solder . Other Precautions
Section Control Measures Respiratory Protection
A NIOSH approved dust/fume respirator should be worn where applicable limits may be exceeded. Local Exhaust Remove smoke from breathing area
Special Not required
V entilation Mechanical Other
Protective Gloves
Use plastic or rubber gloves and aprons where necessary to avoid skin contact.
Eye Protection
Safety glasses or goggles should be worn in areas where splashing may occur .
Other Protective Clothing or Equipment
Provide sufficient mechaniical (general and/or local exhaust) ventilation to maintain exposure below TL V's. Work/Hygienic Practices