AZ762-1C-6D中文资料

POWER RELAY

FEATURES ?Dielectric strength 5000 Vrms ?Low cost

?Epoxy sealed version available ?16 Amp switching

?Isolation spacing greater than 10 mm

?

Reinforced insulation, EN 60730-1 (VDE 0631, part 1),EN 60335-1 (VDE 0700, part 1)?UL, CUR file E44211?VDE 40006031ZET TLER

electronics GmbH

Fax +49 89 800 97 200 https://www.wendangku.net/doc/c57245661.html,

office@https://www.wendangku.net/doc/c57245661.html, 0 97 800 89 +49 Tel. Germany

Puchheim, D-82178 Junkersstrasse 3, 2004-09-27

GENERAL DATA

Life Expectancy

Minimum operations Mechanical 1 x 107

Electrical 1 x 105

at 16 A 250 VAC Res.Operate Time (typical)7 ms at nominal coil voltage Release Time (typical)

3 ms at nominal coil voltage (with no coil suppression)

Dielectric Strength 5000 Vrms coil to contact

(at sea level for 1 min.)1000 Vrms between open contacts Insulation 1000 megohms min. at 20°C Resistance 500 VDC 50% RH Insulation

C250

(according to Overvoltage category: III DIN VDE 0110, Pollution degree: 3

IEC 60664-1)Nominal voltage: 250 VAC

Dropout

Greater than 10% of nominal coil voltage Ambient Temperature

At nominal coil voltage

Operating -40°C (-40°F) to 85°C (185°F)Storage -40°C (-40°F) to 105°C (221°F)Vibration 0.062" (1.5 mm) DA at 10–55 Hz Shock

10 g

Enclosure P .B.T. polyester

Terminals

Tinned copper alloy, P.C.Max. Solder Temp.270°C (518°F)Max. Solder Time 5 seconds Max. Solvent Temp.80°C (176°F)Max. Immersion Time 30 Seconds Weight

14 grams

Packing unit in pcs

20 per plastic tube / 1000 per carton box

CONTACTS

Arrangement SPDT (1 Form C)

SPST (1 Form A, 1 Form B)Ratings

Resistive load:

Max. switched power:480 W or 4432 VA Max. switched current:16 A

Max. switched voltage:150 VDC* or 440 VAC

* Note: If switching voltage is greater than 30VDC,

special precautions must be taken.Please contact the factory.

Rated Load UL, CUR

16 A at 277 VAC resistive, 100k cycles [3]16 A at 277 VAC resistive, 50k cycles [1]1 HP at 250 VAC (1 Form A) [1]1/2

HP at 125 VAC (1 Form A) [1]TV-5 at 125 VAC (1 Form A) [1]

16 A at 277 VAC resistive, 75k cycles [2]B300 Pilot Duty [2]R300 Pilot Duty [2]

VDE 16 A at 250 VAC resistive, [1] [2] and [3]

9 A at 250 VAC, inductive (Form A) [1] [2] and [3]Material Silver cadmium oxide [1] or silver tin oxide [2]or silver nickel [3]. Gold plating available Resistance

< 50 milliohms initially

COIL

Power

At Pickup Voltage 196 mW

(typical)

Max. Continuous 1.7 W at 20°C (68°F) ambient Dissipation Temperature Rise 26°C (47°F) at nominal coil voltage Max. Temperature

130°C (266°F)

NOTES

1.All values at 20°C (68°F).

2.Relay may pull in with less than “Must Operate” value.

3.Specifications subject to change without notice.

2004-09-27

ZET TLER

electronics GmbH

Fax +49 89 800 97 200 https://www.wendangku.net/doc/c57245661.html,

office@https://www.wendangku.net/doc/c57245661.html, 0 97 800 89 +49 Tel.

Germany

Puchheim, D-82178 Junkersstrasse 3,

RELAY ORDERING DATA

COIL SPECIFICATIONS – DC COIL

ORDER NUMBER*

Nominal Coil

Must Operate

Max. Continuous

Coil Resistance

1 Form C 1 Form A

VDC VDC VDC Ohm ± 10%

5

3.5

10.2

62 AZ762–1A–5D

AZ762–1C–5D 6 4.212.390AZ762–1A–6D AZ762–1C–6D 9 6.318.3200AZ762–1A–9D AZ762–1C–9D 128.424.7360 AZ762–1A–12D AZ762–1C–12D 1812.637.0810AZ762–1A–18D AZ762–1C–18D 2416.849.41,440 AZ762–1A–24D

AZ762–1C–24D 4833.698.05,760AZ762–1A–48D AZ762–1C–48D 6042.0112.97,500AZ762–1A–60D AZ762–1C–60D 110

77.0

206.9

25,200

AZ762–1A–110D

AZ762–1C–110D

* “1A” or “1C” denote silver cadmium oxide contacts.Substitute “1B” in place of “1A” for 1 Form B contact.

Add suffix “E” to “1A” or “1B” or “1C” for silver tin oxide contacts. Add suffix “B” to “1A” or “1B” or “1C” for silver nickel contacts. Add suffix “E” at the end of order number for sealed version.

Add suffix “A” at the end of order number for gold plated contacts.