文档库 最新最全的文档下载
当前位置:文档库 › CK12BX472M中文资料

CK12BX472M中文资料

CERAMIC MOLDED AXIAL & RADIAL PERFORMANCE CHARACTERISTICS

GENERAL

Working Voltage:

C0G–50, 100 & 200 Volts

X7R–50, 100 & 200 Volts

Temperature Characteristics:

C0G–0 ±30 PPM/°C from -55°C to +125°C

X7R–±15% from -55°C to +125°C

Capacitance Tolerance:

C0G–±0.5 pF, ±1%, ±2%, ±5%, ±10%, ±20%

(±0.5 pF is tightest available tolerance) X7R–±10%, ±20%, -0 +100%, -20% +80% Construction:

Monolithic block of ceramic dielectric with interdigitated internal electrodes, encapsulated in a molded case, and having axial or radial leads. Meets flame test requirements of UL Standard 94V-0.

Terminal Strength:

EIA-198 Method 303 Condition A (2.2 kg)

ELECTRICAL

Capacitance:

Within specified tolerance when measured with 1 volt rms at 1 kHz (1000 pF or less at 1 MHz for C0G). Dissipation Factor:

25°C at 1 kHz (1000 pF or less at 1 MHz for C0G).

C0G–.15% maximum

X7R–2.5% maximum

Insulation Resistance:

After 2 minutes electrification at 25°C and rated voltage C0G–100K megohms or 1000 megohm - μF, whichever is less.

X7R–100K megohms or 1000 megohm - μF, whichever is less.

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current limited to 50 mA at 25°C.

Life Test:

2000 hours at 200% of rated voltage at 125°C. Post-Test limits at 25°C are:

Capacitance Change:

C0G–less than 3% or 0.25 pF, whichever is higher

X7R–±20% of initial value

Dissipation Factor:

C0G–.25% maximum

X7R–3.0% maximum

Insulation Resistance:

C0G–10K megohms or 100 megohm - μF, whichever is less

X7R–10K megohms or 100 megohm - μF, whichever is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current limited to 50 mA.

ENVIRONMENTAL

Moisture Resistance:

MIL-STD-202, Method 106, or EIA-198, Method 204,

Condition A, except 20 cycles.

Insulation Resistance:

C0G–10K megohms or 100 megohm - μF, whichever is less

X7R–10K megohms or 100 megohm - μF, whichever is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current limited to 50 mA.

Immersion Cycling:

MIL-STD-202, Method 104, Condition B. Post-Test limits at 25°C are:

Insulation Resistance:

C0G–10K megohms or 100 megohm - μF, whichever is less

X7R–10K megohms or 100 megohm - μF, whichever is less

Solderability:

MIL-STD-202, Method 208, Sn62 solder, 245°C for 5 ±1/2 seconds.

Resistance to Soldering Heat:

MIL-STD-202, Method 210, Condition B (260°C, 10 secs).

Depth of immersion — to a minimum of .050" from the capacitor body.

Lead Material:

Axial: Solder-coated copper clad steel

Radial: Solder-coated copper

CERAMIC MOLDED/MIL-C-11015 (CK) &MIL-PRF-39014 (CKR)

DIMENSIONS — INCHES & (MILLIMETERS)

CASE MILITARY

SIZE EQUIVALENT STYLES

L

D

C

C114CK12, CKR11.160 ±.010 (4.06 ±.25).090 ±.010 (2.29 ±.25).020, +.000, -.003 (.51, +.00, -.08)C124CK13, CKR12.250 ±.010 (6.35 ±.25).090 ±.010 (2.29 ±.25).020, +.000, -.003 (.51, +.00, -.08)C192CK14, CKR14.390 ±.010 (9.91 ±.25).140 ±.010 (3.56 ±.25).025, +.002, -.002 (.64, +.05, -.05)C202CK15, CKR15.500 ±.020 (12.70 ±.51).250 ±.015 (6.35 ±.38).025, +.002, -.002 (.64, +.05, -.05)C222

CK16, CKR16

.690 ±.030 (17.53 ±.76)

.350 ±.020 (8.89 ±.51)

.025, +.002, -.002 (.64, +.05, -.05)

CAPACITOR OUTLINE DRAWINGS (AXIAL LEADS)CAPACITOR OUTLINE DRAWINGS (RADIAL LEADS)

DIMENSIONS — INCHES & (MILLIMETERS)

MILITARY S CASE EQUIVALENT H L W LEAD SIZE STYLES HEIGHT

LENGTH

WIDTH

SPACING

CK05, CKR05.190 ±.010 (4.83 ±.25).190 ±.010 (4.83 ±.25).090 ±.010 (2.29 ±.25).200 ±.015 (5.08 ±.38)CK06, CKR06

.290 ±.010 (7.37 ±.25)

.290 ±.010 (7.37 ±.25)

.090 ±.010 (2.29 ±.25)

.200 ±.015 (5.08 ±.38)

C052/C056C062/C066

*Leads are .625 minimum when tape and reel packaged.

M I L -C -11015M I L -P R F -39014

CERAMIC MOLDED/MIL-C-11015 &MIL-PRF-39014 (CKR)

C114T (CKR11)

K 102052C 5K A X 2C CERAMIC *CASE SIZE

(See Table Below)

SPECIFICATION

Military

T — MIL-PRF-39014K — MIL-C-11015

CAPACITANCE

In picofarad code: First two digits are significant figures and third is number of zeroes following (except 9 indicates division by 10). Examples:0.1 ?F = 100,000 pF = 104 and 9.1 pF = 919.See tables for Standard Values.

FAILURE RA TE

INTERNAL CONSTRUCTION

CAPACITANCE TOLERANCE

Standard M —±20%K —±10%

A

—Not Applicable (Std.)M —1.0%P —0.1%R —0.01%S —

0.001%

LEAD MATERIAL

C — Standard

5 — Standard

WORKING VOLTAGE

1—1002—

2005—50

Standard tolerances for each Series are shown in the repetitive parts lists.

*CASE SIZES RADIAL AXIAL C052C114

C056C124C062C192C066C202

C222

TEMPERATURE CHARACTERISTIC

Capacitance Change With Temp.

Measured Measured Without With Bias

KEMET Military EIA Temp.DC Bias (Rated Designator Equivalent Equivalent

Range, °C Voltage Voltage)X BX X7R -55 to ±15%+15%(Stable)+125-25%R BR X7R

-55 to ±15%+15%(Stable)

+125-40%

**

**Part Number Example: C052K102K2X5CA (14 digits – no spaces)

ORDERING INFORMATION

MARKING INFORMATION

C114T (CKR11) THROUGH C222T (CKR16) PER MIL-PRF-39014

JK 103KP537A

J for JAN K for KEMET Capacitance

Capacitance Tolerance, FR Level & Date Code (Yr.)Date and Lot Code

C124T (CKR12)

CKR12

2657J 0537A 31433

Style

Dash No., J for JAN Date &Lot Code Source Code

(Federal Supply Code for Manufacturers,FSCM)

C192T (CKR14) C202T (CKR15) C222T (CKR16)

M390145-2125KEMET 0537A J50V 105K

Complete Part Number Manufacturer ’s Name

Date &Lot Code JAN &Voltage

Capacitance, pF Code, Capacitance Tolerance

C052/56T (CKR05) PER MIL-PRF-39014/01

*Add “V ” as the last digit for stand-off leads.

C062/66T (CKR06) PER MIL-PRF-39014/02

Lot Code &Voltage

Complete MIL Manufacturer ’*Add “V ” as the last digit for stand-off leads.

C114K (CK12) THROUGH C222K (CK16) PER MIL-C-11015

C114K (CK12) C124K (CK13)

KCK 12BX 102K 0537

KEMET, CK

Style (12 or 13), Temp. Char. (BX or BR)

Capacitance, pF Code, Capacitance Tolerance Date Code

C192K (CK14) C202K (CK15) C222K (CK16)

K100V CK14BX 123K 0537

KEMET, Voltage

Style (14, 15 or 16), Temp. Char. (BX or BR)Capacitance, pF Code, Capacitance Tolerance Date Code

C052K (CK05) PER MIL-C-11015/18 &C062K (CK06) PER MIL-C-11015/19

CERAMIC MOLDED/AXIAL — MIL-C-11015 & MIL-PRF-39014

STABLE TEMPERATURE CHARACTERISTICS—BX & BR (EIA-X7R)

M I L -C -11015M I L -P R F -39014

(1) Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014 (2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours,P — .1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)

CERAMIC MOLDED/AXIAL — MIL-C-11015 & MIL-PRF-39014

STABLE TEMPERATURE CHARACTERISTICS—BX & BR (EIA-X7R)

(1) Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014 (2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours,

P — .1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)

CERAMIC MOLDED/RADIAL — MIL-C-11015 & MIL-PRF-39014 STABLE TEMPERATURE CHARACTERISTICS—BX & BR (EIA-X7R)

P — .1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)

(3)Insert “V” for standard design (C056). Leave blank for the flat bottom design (C052).

}

(4)Insert “2” for standard design (Style C052)Note: Stand-offs are available only

Insert “6” for stand-off design (Style C056)with the CKR, not the CK.

CERAMIC MOLDED/RADIAL — MIL-C-11015 & MIL-PRF-39014

STABLE TEMPERATURE CHARACTERISTICS—BX & BR (EIA-X7R)

(1)Insert proper letter for specification: K — MIL-C-11015; T — MIL-PRF-39014.

(2) Failure Rate Designator: A — Not applicable (MIL-C-11015); M — 1%/1000 Hours, P — .1%/1000 Hours, R — .01%/1000 Hours, S — .001%/1000 Hours (MIL-PRF-39014)

(3)Add “V” for stand-off design (C066). Leave blank for the flat bottom design (C062).

(4)Insert “2” for standard design (Style C062). Insert “6” for stand-off design (Style C066). Note: Stand-offs are available only with the CKR, not the CK.

CERAMIC LEADED PACKAGING INFORMATION

CERAMIC LEADED

PACKAGING INFORMATION

Ceramic Radial Tape and Reel Dimensions in Millimeters & (Inches)

Ceramic Radial

Lead Tape and Reel Packaging

(.20") center-to-center.C317**C322**C323**

C333**

C315*C320*

CK05**CKR05**C052**

C056**C066**

CK06**CKR06**C062**C330**C340**Sprocket Hole Diameter Sprocket Hole Pitch Component Pitch Lead Spacing (1)Sprocket Hole Center to Lead Center (1)Sprocket Hole Center to Component Center Height to Seating Plane (straight leads) (2)Component Height Above Tape Center

Dimension

Symbol Nominal mm (inch)Tolerance mm (inch)Dimension Symbol Nominal mm (inch)Tolerance

mm (inch)

Height to Seating Plane (formed leads) (2)Component Alignment Lead Protrusion Composite Tape Thickness

Overall Tape and Lead Thickness Carrier Tape Width Hold-Down Tape Width

Hold-Down Tape Location

Do P0P F P1P2H H1

± 0.2 (.008)± 0.3 (.012)± 0.3 (.012)+0.6 -0.2(+.024 -.008)± 0.7 (.028)± 1.3 (.051)

7301 7303±0.5 (.020) Minimum

Maximum

7301 730316.0 (.630) 18.0 (.709)4.0 (.157)1.0 (.039)0.7 (.051)1.5 (.059)18.0 (.709)5.0 (.197)3.0 (.118)

H 0?h L1t T W W0W2

7301 7303

±0.5 (.020) Minimum ±0.2 (.008)Maximum ±0.2 (.008)Maximum +1.0 - 0.5(+.039 -.020)Minimum Maximum

(1) Measured at the egress from the carrier tape, on the component side.

(2) Determined by a 4 digit suffix placed at the end of the part number, as follows: 7301 = 7303 = 4.0 (.157)12.7 (.500)12.7 (.500)5.08 2.54(.20) (.10)3.81 5.08(.150) (.200)6.35 (.250)

7301 730316.0 (.630) 18.0 (.709)32.2 (1.27)Recommended for parts with formed leads.Recommended for parts with straight leads.Example: C322C104K5R5CA7301Example: C320C104K5R5CA7303

(Note: Non-standard lead lengths

available in bulk only.)

# See page 15 for exact lead configuration for Series.

CERAMIC LEADED

PACKAGING INFORMATION

T a p e a n d R e e l P a c k a g i n g

(2) Quantity varies. For further details, please consult the factory.

相关文档