05-2011, Rev. 0511Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-1
n 2 pole 8A, 2 form C (CO) or 2 form A (NO) contacts n DC or AC coil
n 5kV/10mm coil-contact, reinforced insulation n Ambient temperature up to 85°C
n WG version: product in accordance to IEC60335-1
n Reflow version: for THR (Through-Hole Reflow) soldering process
Typical applications
Boiler control, timers, garage door control, POS automation, interface modules
Approvals
VDE REG.-Nr. 6106, UL E214025, cCSAus 14385
Contact Data
Contact arrangement 2 form C (CO) or 2 form A (NO)Rated voltage 250VAC Max. switching voltage 400VAC Rated current 8A, UL: 10A Limiting continuous current 8A, UL: 10A Limiting making current, max. 4s, duty factor 10% 15A Breaking capacity max. 2000VA Contact material A gNi 90/10, AgNi 90/10 gold plated, AgSnO 2Frequency of operation, with/without load DC coil 360/72000h -1 AC coil 360/36000h -1Operate/release time max., DC coil 8/6ms Bounce time max., DC coil, form A/form B 4/10ms Electrical endurance see electrical endurance graph 1)Contact ratings Type Contact Load Cycles IEC 61810
RT424 DC coil C (CO) 8A, 250VAC, cos φ=1, 85°C 10x103RT444 AC coil A (NO) 8A, 250VAC, cos φ=1, 70°C 50x103RT424 AC coil C (CO) 8A, 250VAC, cos φ=1, 70°C 30x103UL 508
RT424 DC coil A/B (NO/NC) 10A, 250VAC, gen. purpose, 85°C 20x103RT424 DC coil A/B (NO/NC) 1/2hp, 240VAC, 85°C 1x103RT424 DC coil A/B (NO/NC) Pilot duty, B300, R300, 85°C 6x103EN60947-5-1
RTE24 DC coil A/B (NO/NC) AC15, 250VAC, 3A 6.050 RTE24 DC coil A/B (NO/NC) DC13, 24VDC, 2A 6.050 RTE24 DC coil A/B (NO/NC) DC13, 250VDC, 0.2A 6.050EN60730-1
RT424 DC coil A/B (NO/NC) 6(2)A, 250VAC, 85°C 100x103
Contact Data (continued)
Mechanical endurance DC coil
>30x106 operations DC coil, reflow version >10x106 operations AC coil
>5x106 operations AC coil, reflow version
>2x106 operations
Coil Data
Coil voltage range, DC coil/AC coil 5 to 110VDC / 24 to 230VAC Operative range, IEC 61810 2Coil insulation system according UL class F Coil versions, DC coil Coil Rated Operate Release
Coil Rated coil code voltage voltage voltage resistance power VDC VDC VDC ?±10%2) mW 005 5 3.5 0.5 62 403 006 6 4.2 0.6 90 400 009 9 6.3 0.9 200 400 012 12 8.4 1.2 360 400 024 24 16.8 2.4 1440 400 048 48 33.6 4.8 5520 417 060 60 42.0 6.0 85702) 420 110 110 77.0 11.0
288002)
420
2) Coil resistance ±12%. All figures are given for coil without pre-energization, at ambient temperature +23°C. Other coil voltages on request.
Coil versions, AC coil 50Hz
Coil Rated Operate Release Coil Rated coil code voltage voltage voltage resistance
power VAC VAC VAC ?±15%3) VA 524 24 18.0 3.6 3503) 0.76 615 115 86.3 17.3 8100 0.76 620 120 90.0 18.0 8800 0.75 700 200 150.0 30.0 24350 0.76 730 230 172.5
34.5 32500 0.74
3) Coil resistance ±10%. All figures are given for coil without pre-energization, at ambient temperature +23°C, 50Hz. Other coil voltages on request.
Power PCB Relay RT2
F0149-C
Z V b
05-2011, Rev. 0511Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-2
Other Data (continued)
Terminal type PCB-THT, plug-in
reflow version PCB-THR Mounting distance, AC coil ≥2.5mm Weight 13g Resistance to soldering heat THT, IEC 60068-2-20 RTII 270°C/10s RTIII 260°C/5s Resistance to soldering heat THR
reflow soldering (for reflow version) forced gas convection 4) or vapour phase 5) temperature profile according EN61730Packaging/unit tube/20pcs., box/500pcs.
5) recommended fluid LS/230
Accessories
For details see datasheet
A ccessories Industrial Power Relay RT NOTE: indicated contact ratings and electrical endurance data for direct wiring of relays (according IEC 61810-1); for relays mounted on sockets deratings may apply.
Insulation Data
Initial dielectric strength between open contacts 1000V rms between contact and coil 5000V rms between adjacent contacts 2500V rms Clearance/creepage
between contact and coil ≥10/10mm between adjacent contacts ≥3/4mm Material group of insulation parts IIIa Tracking index of relay base PTI 250V reflow version
PTI 175V
Other Data
Material compliance: EU RoHS/ELV , China RoHS, REACH, Halogen content refer to the Product Compliance Support Center at https://www.wendangku.net/doc/d616382943.html,/customersupport/rohssupportcenter Resistance to heat and fire WG version or reflow version according EN60335, par30Ambient temperature DC coil -40 to 85°C AC coil -40 to 70°C AgSnO 2 contacts -40 to 70°C Category of environmental protection, IEC 61810 standard version RTII - flux proof, RTIII - wash tight reflow version RTII - flux proof Vibration resistance (functional),
form A/form B contact, 30 to 300Hz 20g/5g Shock resistance (destructive)
100g
PCB layout / terminal assignment
Bottom view on solder pins
S0163-BJ
S0163-BK
*) With the recommended PCB hole sizes a grid pattern from 2.5 m m to 2.54 m m can be used.
Dimensions
Process conditions for Reflow soldering
according to EN61760-1
THT version
THR version (reflow solderable)
Product code structure Typical product code RT 4 2 4 024
Type
RT Power PCB Relay RT2
Version
4 8A, pinning 5mm, flux proof
E 8A, pinning 5mm, wash tight (not for Reflow version)
Contact arrangement
2 2 form C (CO) contacts
4 2 form A (NO) contacts
Contact material
3 AgSnO
4 AgNi 90/10
5 AgNi 90/10 gold plated
Coil
Coil code: please refer to coil versions table
Version
Blank Standard version
WG Product in accordance with IEC 60335-1 (domestic appliances)
R Reflow solderable
Product code Version Contacts Contact material Coil Version Part number
RT423730 8A, 2 form C (CO) AgSnO 230VAC Standard 4-1393243-3
RT424005 pinning 5mm, contacts AgNi 90/10 5VDC 5-1393243-9
RT424006 flux proof 6VDC 6-1393243-1
RT424012 12VDC 6-1393243-3
RT424012WG IEC60335-1 compliant 7-1415538-8
RT424024 24VDC Standard 6-1393243-8
RT424024WG IEC60335-1 compliant 7-1415538-7
RT424048 48VDC Standard 7-1393243-0
RT424060 60VDC 7-1393243-3
RT424110 110VDC 7-1393243-5
RT424524 24VAC 7-1393243-6
RT424615 115VAC 7-1393243-8
RT424730 230VAC 7-1393243-9
RT425003 AgNi 90/10 3VDC 7-1415525-1
RT425005 gold plated 5VDC 8-1393243-0
RT425012 12VDC 8-1393243-2
RT425024 24VDC 8-1393243-5
RT444012 2 form A (NO) AgNi 90/10 12VDC 9-1393243-7
RT444024 contacts 24VDC 9-1393243-9
RTE24005 8A, 2 form C (CO) 5VDC 1393243-1
RTE24006 pinning 5mm, contacts 6VDC 1393243-2
RTE24012 wash tight 12VDC 1393243-4
RTE24024 24VDC 1-1393243-0
RTE24048 48VDC 1-1393243-1
RTE24110 110VDC 1-1393243-4
RTE24524 24VAC 1-1393243-5
RTE24615 115VAC 1-1393243-7
RTE24730 230VAC 1-1393243-8
RTE25005 AgNi 90/10 5VDC 1-1393243-9
RTE25012 gold plated 12VDC 2-1393243-0
RTE25024 24VDC 2-1393243-1
RTE25524 2-1393243-4
RTE43009 2 form A (NO) AgSnO 9VDC 4-1415535-1
RTE44009 contacts AgNi 90/10 3-1393243-1
RTE44730 230VAC 3-1393243-5
This list represents the most common types and does not show all variants covered by this datasheet.
3 05-2011, Rev. 0511Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-
分销商库存信息:
TE Connectivity / Schrack RT424005