当前位置：文档库 › FAR-C7CF-06000-G39R中文资料

FAR-C7CF-06000-G39R中文资料

DS62-01001-1E

FUJITSU MEDIA DEVICE

DATA SHEET

LEAD FREE RESONA TORS

FAR Resonators

(RESONATOR 6 MHz to 25 MHz)

C7 Series (Type F/G/H)

s GENERAL DESCRIPTION

FAR C7 series is the small and highly precise resonator which is utilizing L T (LiT aO 3 : Lithium T antalate) crystal with high electro-mechanical coupling coefficient and has built-in load capacitors for use in microprocessor clock in the small ceramic package of low profile. FAR C7 series is excellent in the mechanical property, and has realized high reliability.

s FEATURES

?Frequency Range : 6 MHz to 25 MHz ?Ultra-small package

?Built-in load capacitors for use in microprocessor clock ?Completely lead-free device.

?Excellent in heat resistance to lead-free reflow soldering (Reflow temperature at +260 °C) ?

High reliability, excellent in shock and vibration resistance

s PACKAGES

C7 Series (Type F/G/H)

2s PRODUCT LINEUP

* : Other frequency tolerances available. Contact our sales representatives for specific requirements.

C7 Series (Type F/G/H)

s STANDARD FREQUENCIES

Notes : ? Other frequencies (within 6 MHz to 25 MHz) than standard are available.

? Standard resonant resistance is specified according to applied frequency.

s NOTES FOR USE

?The C7 series is designed in due consideration of impact resistance. The product can however be damaged by excessive impact applied, for example, when the product is let fall. Be careful in handling it.?Solder under the following conditions :

10 seconds Max at + 260 °C (temperature at surface of substrate)

Preheating is recommended to avoid extreme temperature change on device.?Avoid rapid and drastic temperature change during operation.?There is no specific direction in resonator mounting.

?Although the characteristics of the product are adjusted with the Fujitsu’s standard circuit, some of them may change depending on the combination with the IC used actually and on the design conditions of the target board. It is strongly recommended to check oscillation characteristic data before using the product in a real circuit. Also, Fujitsu is ready to obtain oscillation data from the IC or board of interest supplied from the customer.?This device is designed for reflow soldering and not fit for flow soldering.

Standard Frequency

[kHz]

Package Size

Resonance Resistance C7 Series (type F/G/H) 6000F 800 ? Max (Symbol : 9) 8000F 400 ? Max (Symbol : 8) 12000G 300 ? Max (Symbol : 0) 16000G 150 ? Max (Symbol : 1) 24000

300 ? Max (Symbol : 0)

C7 Series (Type F/G/H)

4s PART NUMBERING SYSTEM

(1) Series

(2) Package Type

(3) Package Size

(4) Frequency

See “s ST ANDARD FREQUENCIES”. (Example) Unit : kHz (Expressed in five digits)

8.0 MHz → 08000

(5) Initial Frequency Tolerance

(6) Built-in Load Capacitors

FAR?C7C??

(1) (2) (3) (4) (5) (6) (7) (8) (9)

Series Single Crystal Load Capacitors

C7LiTaO3Built-in

Designator Package Type

C CHIP

Designators Package Size

F 4.8 × 2.1 × 1.2 mm

G 3.2 × 2.1 × 0.9 mm

H 1.9 × 1.5 × 0.7 mm

Designators Initial Frequency Tolerance

G± 500 ppm

J± 1,000 ppm

K± 3,000 ppm

M± 5,000 ppm

Designators Capacitance

110pF± 4 pF

35pF± 2 pF

C7 Series (Type F/G/H)

(7) Resonance Resistance

(8) Customization

(9) Taping Specification Designators

Resonance Resistance

0300 ? Max 1150 ? Max 8400 ? Max 9

800 ? Max

Designators

Descriptions

? Not specified

A to Z

Serial number for custom design.

Designators

Descriptions

12 mm width career tape (F/G package) 8 mm width career tape (H package)

C7 Series (Type F/G/H)

6s MARKING

The manufacturing code (EIAJ) is expressed as in a cycle of 4 years according to the following table.

Jan.Feb.Mar.Apr.May Jun.Jul.Aug.Sep.Oct.Nov.Dec.

2001A B C D E F G H J K L M 2002N P Q R S T U V W X Y Z 2003a b c d e f g h j k l m 2004n p q r s t u v w x y z

C7 Series (Type F/G/H)

C7 Series (Type F/G/H) s TAPE AND REEL

C7 Series (Type F/G/H)

The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU MEDIA DEVICES sales representatives before ordering.

The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU MEDIA DEVICES electronic device; FUJITSU MEDIA DEVICES does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU MEDIA DEVICES assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MEDIA DEVICES or any third party or does FUJITSU MEDIA DEVICES warrant non-infringement of any third-party’s intellectual property right or other right by using such information. FUJITSU MEDIA DEVICES assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein.

The products described in this document are designed, and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).

Please note that FUJITSU MEDIA DEVICES will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products.

Any electronic devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions.

If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Control Law of Japan, the prior authorization by Japanese government should be required for export of those products from Japan.

F0411

?2004 FUJITSU LIMITED Printed in Japan