原料物性表(模板)

表

标识中文名：乙二醛英文名：glyoxal

分子式：C2H2O2分子量：58.04 CAS NO号：107-22-2

理化性质外观与性状：无色或黄色有潮解性的结晶或液体, 蒸气为绿色。

熔点(℃)：15 溶解性：溶于乙醇、醚，溶于水。沸点(℃)：50.5 相对密度(水=1)：1.14

燃烧爆炸危险性燃爆危险：本品易燃，有毒，具刺激性。

燃烧性：有害燃烧产物：一氧化碳、二氧化碳。闪点(℃)：稳定性：

爆炸极限(V%)：禁忌物：

引燃温度(℃)：灭火方法：

危险特性毒性

人体危害

个体防护呼吸系统防护：眼睛防护：

身体防护：

手防护：

其他防护：

急救措施皮肤接触：眼睛接触：吸入：

食入：

泄漏应急

处理

表10 甲醇甲醇

标识中文名：甲醇英文名：methyl alcohol

分子式：分子量：CAS NO号：67-56-1

理化性质外观与性状：无色澄清液体，有刺激性气味。

熔点(℃)：-97.8 溶解性：溶于水，可混溶于醇、醚等多数有机溶剂。沸点(℃)：64.8 相对密度(水=1)：0.79

燃烧爆炸危险性燃爆危险：本品易燃，具刺激性。

燃烧性：易燃有害燃烧产物：一氧化碳、二氧化碳。

闪点(℃)：11 稳定性：—

爆炸极限(V%)：385 禁忌物：酸类、酸酐、强氧化剂、碱金属。

引燃温度(℃)：5.5～44.0

灭火方法：尽可能将容器从火场移至空旷处。喷水保持火

场容器冷却，直至灭火结束。处在火场中的容器若已变色

或从安全泄压装置中产生声音，必须马上撤离。灭火剂：

抗溶性泡沫、干粉、二氧化碳、砂土。

危险特性易燃，其蒸气与空气可形成爆炸性混合物，遇明火、高热能引起燃烧爆炸。与氧化剂接触发生化学反应或引起燃烧。在火场中，受热的容器有爆炸危险。其蒸气比空气重，能在较低处扩散到相当远的地方，遇火源会着火回燃。

毒性LD50：5628 mg/kg(大鼠经口)；15800 mg/kg(兔经皮) LC50：83776mg/m3，4小时(大鼠吸入)

人体危害对中枢神经系统有麻醉作用；对视神经和视网膜有特殊选择作用，引起病变；可致代射性酸中毒。急性中毒：短时大量吸入出现轻度眼上呼吸道刺激症状（口服有胃肠道刺激症状）；经一段时间潜伏期后出现头痛、头晕、乏力、眩晕、酒醉感、意识朦胧、谵妄，甚至昏迷。视神经及视网膜病变，可有视物模糊、复视等，重者失明。代谢性酸中毒时出现二氧化碳结合力下降、呼吸加速等。慢性影响：神经衰弱综合征，植物神经功能失调，粘膜刺激，视力减退等。皮肤出现脱脂、皮炎等。

个体防护呼吸系统防护：可能接触其蒸气时，应该佩戴过滤式防毒面具（半面罩）。紧急事态抢救或撤离时，建议佩戴空气呼吸器。

眼睛防护：戴化学安全防护眼镜。

身体防护：穿防静电工作服。

手防护：戴橡胶手套。

其他防护：工作现场禁止吸烟、进食和饮水。工作完毕，淋浴更衣。实行就业前和定期的体检。

急救措施皮肤接触：脱去污染的衣着，用肥皂水和清水彻底冲洗皮肤。

眼睛接触：提起眼睑，用流动清水或生理盐水冲洗。就医。

吸入：迅速脱离现场至空气新鲜处。保持呼吸道通畅。如呼吸困难，给输氧。如呼吸停止，立即进行人工呼吸。就医。

食入：饮足量温水，催吐。用清水或1％硫代硫酸钠溶液洗胃。就医。

泄漏应急处理迅速撤离泄漏污染区人员至安全区，并进行隔离，严格限制出入。切断火源。建议应急处理人员戴自给正压式呼吸器，穿防静电工作服。不要直接接触泄漏物。尽可能切断泄漏源。防止流入下水道、排洪沟等限制性空间。

小量泄漏：用砂土或其它不燃材料吸附或吸收。也可以用大量水冲洗，洗水稀释后放入废水系统。

大量泄漏：构筑围堤或挖坑收容。用泡沫覆盖，降低蒸气灾害。用防爆泵转移至槽车或专用收集器内，回收或运至废物处理场所处置。

物性材料表

特性Feature 耐高温、耐冲击、高流动性、尺寸稳定。High temperature resistance, impact resistance, high liquidity, dimension stability. 用途Use 电子、电器零件、汽车部件等。Electronic, electrical parts, auto parts, etc. 注塑条件Injection conditions 预干燥温度Pre-drying temperature 预干燥时间Pre-drying time 进料区温度Feed zone temperature 压缩区温度Compression zone temperature 熔融区温度Melting zone temperature 喷嘴温度Nozzle Temperature 模具温度Mold 注射压力Injection pressure 物理机械性能Physical and mechanical properties 项目Project 单位unit 试验方法Test method 数值Value 密度Density 熔点Melting point 成型收缩率Mold Shrinkage 吸水率（24小时，23℃）Water Absorption (24 hours, 23 ℃) 熔融指数Melt Index 阻燃等级Flame Rating 拉伸断裂强度Tensile Strength 拉伸模量Tensile modulus 断裂伸长率Elongation at break 弯曲强度Bending 弯曲模量Bending modulus 悬臂梁（无缺口）冲击强度Izod (unnotched) impact strength 悬臂梁缺口冲击强度Izod notched impact strength 洛氏硬度Rockwell hardness 热变形温度（0.45MPa）Heat Deflection Temperature（0.45MPa） Dielectric Strength 绝缘破坏强度 Arc resistance 耐电弧性 Dielectric Constant 介电常数 Dielectric Losses 介电损耗 Characteristics 特性 平衡吸湿量Moisture Absorption at Equilibrium 线性成型收缩率，横向Linear Mould Shrinkage, Transverse 断裂伸长率Elongation at Break 屈服伸长率Elongation at Yield

PA10T材料物性表

P ROVISIONAL D ATA S HEET G RIVORY HT G RIVORY XE 4027 BLACK 9916 Product description Grivory XE 4027 black 9916 is a 30% glass-fibre reinforced flame retardant (UL 94 V-0) engineering thermoplastic material based on a semicrystalline, partially aromatic co-polyamide. Grivory XE 4027 black 9916 is free of halogens and red phosphorus. RoHS: Grivory XE 4027 black 9916 is in compliance with RoHS (2002/95/EC, Re-striction of Hazardous Substances). WEEE:Parts produced from Grivory XE 4027 black 9916 are not subject to "selec-tive treatment" according the Directive 2002/96/EC on Waste Electrical and Elec-tronic Equipment. ISO polymer designation: PA 10T/X ASTM designation: PPA, polyphthalamide The main distinguishing features of Grivory HT-PPA, when compared to other poly-amides, are its good performance at high temperatures providing parts which are stiffer, stronger, have better heat distortion and dimensional stability as well as excel-lent chemical resistance and low moisture absorption. Grivory XE 4027 black 9916 is especially suitable for injection moulded components in electrical and electronic applications which require a flame class acc. UL 94 V-0. The material is suitable for lead-free SMT reflow soldering acc. i.e. JEDEC J-STD-020C (peak temperature 260°C). Compo-nents conforming to JEDEC MSL1 are achievable.

Sabic DX10311原料物性表

L NP* Thermocomp* Compound DX10311A sia Pacific: COMMERCIAL DX10311 is 30% glass fiber reinforced, impact modified polycarbonate resin. High flow and good ductility. T YPICAL PROPERTIES 1 TYPICAL VALUE UNIT STANDARD M ECHANICAL T ensile Stress, brk, Type I, 5 mm/min 117M Pa A STM D 638T ensile Strain, brk, Type I, 5 mm/min 2.6%A STM D 638T ensile Modulus, 5 mm/min 8330M Pa A STM D 638F lexural Stress 190M Pa A STM D 790F lexural Modulus 7670M Pa A STM D 790T ensile Stress, break, 5 mm/min 119M Pa I SO 527T ensile Strain, break, 5 mm/min 2.7%I SO 527T ensile Modulus, 1 mm/min 8260M Pa I SO 527F lexural Stress, yield, 2 mm/min 182M Pa I SO 178F lexural Stress, break, 2 mm/min 181M Pa I SO 178F lexural Modulus, 2 mm/min 7720M Pa I SO 178I MPACT Charpy Impact, unnotched, 23°C 57k J/m2I SO 179/2C Izod Impact, unnotched, 23°C 752J /m A STM D 4812 Izod Impact, notched, 23°C 196J /m A STM D 256 Charpy Impact, notched, 23°C 20k J/m2I SO 179/2C T HERMAL H DT, 0.45 MPa, 3.2 mm, unannealed 128°C A STM D 648 CTE, -40°C to 40°C, flow 1.9E-051/°C A STM E 831 CTE, -40°C to 40°C, xflow 6.4E-051/°C A STM E 831P HYSICAL S pecific Gravity 1.42-A STM D 792M old Shrinkage, flow, 3.2 mm (5)0.1 - 0.3%S ABIC Method M old Shrinkage, xflow, 3.2 mm (5) 0.2 - 0.4% S ABIC Method Melt Volume Rate, MVR at 300°C/5.0 kg 37 c m3/10 min I SO 1133 1) 2) PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE SABIC INNOVATIVE PLASTICS Source, GMD, Last Update: COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("SABIC IP"), ARE SOLD SUBJECT TO SABIC IP' S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SABIC IP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SABIC IP MATERIALS, PRODUCTS, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN SABIC IP' S STANDARD CONDITIONS OF SALE, SABIC IP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN.Each user bears full responsibility for making its own determination as to the suitability of SABIC IP' s materials, products, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses necessary to assure that its finished parts incorporating SABIC IP materials or products will be safe and suitable for use under end-use conditions. Nothing in this or any other document, nor any oral recommendation or advice, shall be deemed to alter, vary, supersede, or waive any provision of SABIC IP' s Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by SABIC IP. No statement contained herein concerning a possible or suggested use of any material, product or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of SABIC Innovative Plastics Company or any of its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product or design in the infringement of any patent or other intellectual property right * LNP is a trademark of the SABIC Innovative Plastics Company * Thermocomp is a trademark of the SABIC Innovative Plastics Company ? 1997-2011 SABIC Innovative Plastics Company.All rights reserved T ypical values only. Variations within normal tolerances are possible for variose colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity. All properties, except the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294. O nly typical data for material selection purpose.Not to be used for p art or tool design. 3) T his rating is not intended to reflect hazards presented by this or any o ther material under actual fire conditions.4) O wn measurement according to UL. 5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

常见塑料物性的检测及标准

常见塑料物性的检测及标准 流动系数 （1）测试的标准：ASTMD1238 （2）常用的测试标准的量测仪器是溶液指数计（Melt In deGer ）. （3）流动系数检测方法：是一种表示塑胶材料加工时的流动性的数值。它是美 国量测标准协会（ASTM）根据美国杜邦公司（DuPont）惯用的鉴定塑料特性的方法制定而成，其测试方法是先让塑料粒在一定时间（10分钟）内、一定温度及压力（各种材料标准不同）下，融化成塑料流体，然后通过一直径为 2.1mm圆 管所流出的克（g）数。其值越大，表示该塑胶材料的加工流动性越佳，反之则越差。（4）测试的具体操作过程是：将待测高分子（塑料）原料置入小槽中，槽末接 有细管，细管直径为2.095mm，管长为8mm。加热至某温度后，原料上端藉由活塞施加某一定重量向下压挤，量测该原料在10分钟内所被挤出的重量，即 为该塑料的流动指数。有时您会看到这样的表示法？MI25g/10min ，它表示在 10分钟内该塑料被挤出25克。一般常用塑料的MI值大约介于1~25之间。MI愈大，代表该塑料原料粘度愈小及分子重量愈小，反之则代表该塑料粘度愈大及分子重量愈大。收缩率 测试的标准：ASTMD955 塑胶制品经冷却、固化并脱模成形后，其尺寸与原模具尺寸之差的百分比。 （3）因结构不同的关系，结晶性塑料与非结晶性塑料的收缩率存在明显的差异。一般地，结晶性塑料的收缩率比非结晶性塑料的收缩率大上好几倍（如下表所示）。同时有添加玻璃纤维或其它强化剂的塑胶材料，其收缩率可降低好几倍。

影响成型收缩的因素有热收缩、结晶度(热塑性)或硬化度(热固性) 、弹性回 复、分子配向、与成型条件等因素。 <1>热塑性塑料 <2>热固性塑料 塑料名称 成形收缩率(%) 塑料名称 成形收缩率(%) EP 0.1~0.5 SP 0.0~0.5 MF 0.5~1.5 UF 0.6~1.4 塑料名称 成形收缩率 (%) ABS 0.3~0.8 AS 0.2~0.7 CA 0.3~0.8 CAB 0.4~0.5 CAP 1 CP 0.4~0.5 EC 0.4~0.5 EPS 0.4 FEP 3.0~4.0 FRP 0.1~0.4 EVA 0.5~1.5 HDPE 1.2~2.2 HIPS 0.2~1.0 LCP 0.1~1.0 LDPE 1.5~3.0 塑料名称 成形收缩率 (%) PA 0.6~2.5 PA-6 0.5~2.2 PA-66 0.5~2.5 PA-610 1.2 PA-612 1.1 PA-11 1.2 PA-12 0.3~1.5 PAR 0.8~1.0 PBT 1.3~2.4 PC 0.4~0.7 PCTFE 0.2~2.5 PE 0.5~2.5 PET 2.0~2.5 PES 0.5~1.0 PMMA 0.2~0.8 塑料名称 成形收缩率 (%) POM 0.8~3.5 PP 1.0~2.5 PPO 0.5~0.7 PPS 0.6~1.4 PS 0.2~1.0 PVA 0.5~1.5 PVAC 0.5~1.5 PVB 0.5~1.5 硬质PVC 0.1~0.5 软质PVC 1.0~5.0 PVCA 1.0~5.0 PVDC 0.5~ 2.5 PVFM 0.5~1.5 SAN 0.2~0.6 SB 0.2~1.0

锂电材料物性对比

电池材料厂家技术标准积累 深圳市贝特瑞 MSG-S(518) 负极石墨粒径：D10=9.764；D50=17.136um；D90=28.189；水分:0.039;碳含量:99.952;TAP密度;1.036 比表面 积:2.784；首次容量/效率:363.51/94.18 深圳市贝特瑞 518 负极石墨粒径：D10=9.862；D50=16.888um； D90=28.374；水分:0.04%; 碳含量:99.962; TAP密度;1.042% 比表面积:2.625；首次容量/效率:352.3/92.5% 深圳市贝特瑞 AG 负极石墨粒径：D10=7.137；D50=18.058um； D90=37.495；水分：0.035;碳含量：99.676;TAP密度：1.001 首次容量/效率:320.83/90.42% 深圳市贝特瑞 AG 负极石墨粒径：D10=7.53；D50=17.779um； D90=39.648；水分：0.041;碳含量：99.743;TAP密度：1.002 ，首次容量/效率:326.51/90.67% 深圳市贝特瑞 SAG-23 负极石墨粒径：D10=8.318；D50=21.097um； D90=47.119；水分：0.04；碳含量：99.925；TAP密度：1.021 ，比表面积:4.605；首次容量/效率:332.11/92.08 深圳市贝特瑞 818 负极石墨粒径：D10=11.453；D50=18.226um； D90=28.762；水分：0.036；碳含量：99.964;TAP密度：1.121 比表面积:1.947;首次容量/效率:364.63/95.29% 深圳市贝特瑞 818 负极石墨粒径：D10=10.859；D50=18.033um；

塑料原料之物性说明

塑料原料之物性说明 一流动特性(FLOW PROPERTIES) 热塑性塑料成型过程一般需经历加热塑化, 流动成型和冷却固化三个基本步骤.所谓加热塑化就是经过加热使固体高聚物变成粘性流体; 流动成型是借助注射机或挤塑机的柱塞或螺杆的移动,以很高的压力将粘性流体注入温度较低的闭合模具内,或以很高的压力将粘性流体从所要求形状的口模挤出,得到连续的型材;冷却固化是用冷却的方法使制品从粘流态变成玻璃态.几乎所有高聚物都是利用其粘流态下的流动行为进行加工成型的.表征流动特性的物理量如下: 1.熔融指数值(MELT INDEX) 熔融指数是评价热塑性聚合物特别是聚烯烃的挤压性的一种简单而实用的方法,其定义为: 在一定温度下, 熔融状态的高聚物在一定负荷下, 十分锺内从规定直径和长度的标准毛细管中流出的重量.其一般在熔融指数仪中测定. 可挤压性是指聚合物通过挤压作用形变时获得形状和保持形状的能力, 研究聚合物的挤出性质能对制品的材料和加工工艺作出正确的选择和控制,通常条件下,聚合物在固体状态不能通过挤压而成型,只有当聚合物处于粘流态时才能通过挤压获得宏观而有用的形变.挤压过程中,聚合物熔体主要受到剪切作用,故可挤压性主要取决于熔体的剪切粘度和拉伸粘度.大多数聚物熔体的粘度随剪切力或剪切速率增大而降低.. 熔融指数仪测定在给定剪切力下聚合物的流动度,用定温下10分锺内聚合物从出料孔挤出的重量(克)来表示,其数值就称为熔融指数. 所以流动度,即熔融指数实际上反映了聚合物分子量的大小,分子量较高的聚合物更易于缠结,分子体积更大,故有较大的流动阴力,表现出较高的粘度和低的流动度,亦即熔融指数低. 由于荷重小(1.2kgf)通测定的MI值不能说明注射或挤出成型时聚合物的实际流动性能.但用[MI]值能方便地表示聚合物流动性的高低. 2. 粘度 VISCOSITY ( Psi *S)

特殊塑胶材料PMMA CM-205物性表

The above statement is based on our current level of knowledge and covers the above products directly manufactured and supplied by CHI MEI CORPORA TION at the date of issue. CHI MEI CORPORA TION makes no warranties, whether express or implied, and assumes no liability in connection with any use of above information. Notwithstanding the foregoing, CHI MEI CORPORA TION shall in no event be held obligated or liable for any claims due to or arising from (i) any customer provided, consigned, materials and/or parts, which are incorporated or adopted in the products; (ii) any combination of the products with material not provided or authorized by our company; (iii) any modifications to the products which are made or directed by customer; (iv) our compliance with the specifications, instructions, and/or designs provided by customer; (v) any anti-trust, unfair competition and/or other unlawful actions effected by customer; or (vi) any defects, infringement, breach and/or violatio n which are arising out of customer’s faults or otherwise not solely and directly attributable to CHI MEI CORPORA TION. In no event will CHI MEI CORPORA TION be liable for any indirect, special, exemplary, punitive, or consequential damages (including lost profits) of any nature whatsoever whether arising out of the purchase, shipment, unloading, handling, or use of any product or otherwise. PMMA ACRYREX ? CM-205 產品敘述: High viscosity 物性 ISO 測試方法 測試條件 單位 CM-205 熔融指數 230℃×3.8KG ml/10 min 1.9 比重 1183 23 ℃ g/cm 3 1.19 拉伸強度 527 50 mm/min, yield MPa 70 50 mm/min, break MPa 70 延伸率 527 50 mm/min % 12 彎曲強度 178 2 mm/min MPa 103 彎曲彈性模數 2 mm/min GPa 2.8 IZOD 衝擊強度 180/1A 23 ℃ Notched KJ/m 2 2 -30 ℃ Notched KJ/m 2 - Charpy 衝擊強度 179 23 ℃ Notched KJ/m 2 2 -30 ℃ Notched KJ/m 2 - 維氏軟化溫度 306 1 Kg,50 ℃/hr ℃ 115 5 Kg,50 ℃/hr ℃ 107 熱變形溫度 75/A 1.8 MPa Unannealed ℃ 95 1.8 MPa Annealed ℃ 104 線膨脹係數 11359 - - 6 X 10-5 燃燒等級 - UL-94 - 1.5mm HB 成型收縮率 294-4 - % 0.2~0.6 標記 1043 - - >PMMA< January 16, 2017 Notes ：These are typical properties only and are not to be construed as specifications. Users should confirm results by their own tests.

材料物性表

EXTRUSION APPLICATION

Introduction Responsible for a long line of accomplishments in outstanding engineering plastics, UBE NYLON products have won the trust and respect of users the world over. UBE NYLON – NYLON 6, NYLON COPOLYMERS – is in wide use throughout industry with their unique properties utilized to their fullest potential. UBE NYLON 6 has a number of excellent properties as follows: Excellent in impact strength and rigidity Having a smaller friction coefficient, thus excellent in abrasion resistance Excellent in resistance to oils, solvents and chemicals Superior in heat resistance Appropriate to mass production, contributing to cost reduction Summary 1. Introduction 2. Nomenclature 3. Monofilament Applications 4. Film Applications 5. TERPALEX Polyamide 6/66/12 Copolymer Nomenclature The first 2 digits in the code indicate the type of Polyamide. The third and fourth digits indicate the molecular weight level for 1000 series. In case of copolymer, the third digit shows the viscosity level. The co-polymerization ratio can be roughly calculated from the fourth digit multiplying by 5. “T” means the basic grade for monofilament application and the grade contain some additives for maintain good process stability and high trans-parency. In case of “MT”, means monomer con-taining grade offering good flexibility and softness. 10: Polyamide 6 homopolymer 50: Polyamide 6/66 copolymer 70: Polyamide 6/12 copolymer Ex. 1022FDX04: : c.a. 22 x 1,000 = 22,000 Ex. 5034MTX1: : level = 3 (high viscosity) : c.a. 80/20(4 x 5 = 20et%) : monomer-contain type 2 Introduction

塑胶原料物性大全

塑胶原料物性大全塑胶原料物性大全PVC硬度对照表 万年历查询 塑料单位换算表 7-1 概论 7-2 塑品设计之通则 6-1 结构发泡成形方法 6-2 结构发泡设计之考虑 6-3 塑品设计 6-4 组装方法 5-1 概论 5-2 材料之考虑 5-3 设计之考虑 5-4 尺寸因素与公差 4-1 概论 4-2 模具设计 4-3 产品设计之建议 3-1 概论 3-2 材料之考虑 3-3 设计之建议 3-4 发泡异形押出 3-5 拉挤成形(pultrusions) 2-1 概论 2-2 原型之设计

2-3 产品设计 2-4 模具设计 2-5 组装设计 1-1 塑料材料的选择 1-2 塑料加工方式的选择 PVC塑料配方的设计 PVC造粒中起粒原因分析 TPR/TPE热塑性弹性体的注塑成型 制品烫印故障的成因及对策 塑料压铸工艺介绍 塑料原料在加工过程中的不良反应与解决办法塑料抗静电配方 塑料挤出机的电器故障和维修方法 塑料挤胀成型技术 嵌件注塑成型技术的特点 抗静电PVC产品配方 水溶性塑料薄膜的特点及生产要领 注塑成型中出现熔接痕现象的分析和解决 注塑成型步骤一物料干燥 注塑成型步骤三(1)机台的参数设置 注塑成型步骤三塑化计量设置 注塑成型步骤二模温的设定 注塑过程中改性尼龙的应用介绍 牛奶膜的生产工艺介绍 硬质CPVC的挤出工艺解析

聚丙烯PP的成型 聚丙烯导电配方 聚丙烯类阻燃配方 聚乙烯PE的注塑成型工艺 聚乙烯的着色配方（绿色类） 聚乙烯着色配方（红色类） 聚乙烯着色配方（黄色类） 聚乙烯类阻燃配方 聚氯乙烯填充配方 迈格机械新款系列吹瓶机技术详解 通用工程塑料PBT在注塑行业里的具体应用采用小浇口进行注射成型的优点 ＰＶＣ塑料扣板使用方法 废旧塑料的风筛分离 再生LDPE工艺流程 再生PET工艺流程 再生PP聚丙乙烯工艺流程 再生PVC（硬料）工艺流程 塑料造粒小贴士 ABS塑料及产品注射成型工艺 LLDPE拉伸膜、保鲜膜的生产与应用研究 PET塑料及产品注射成型工艺 PET注拉吹制品壁厚分布的研究 TPR/TPE热塑性弹性体的注塑成型工艺 UPVC注射成型工艺

物性表

Safety Data Sheet complies with:directive 91/155/EEC revision:2.0 ISO 11014-1:Safety data sheet for chemical products. revision date:02/02/1998date of issue: 26/02/1998 p 1. Product and company identification Product name:Stanyl ?Product code:TE250F3 Manufacturer: DSM Engineering Plastics P.O. Box 43,6130 AA Sittard The Netherlands Emergency number: The Netherlands +31 (0)46 4 76 55 55 2. Composition/Information on ingredients This chemical product is a preparation Chemical nature:(poly)amide PA 46CAS number:50327-22-5Components contributing to the hazard: The material contains Sb 2O 3 as a synergist with an average content of max. 7%. Sb 2O 3 is classified as a harmful (Xn) substance with a risk phrase R40 carcinogen class 3. However, the Sb 2O 3 is embedded in an impervious matrix of polymer and is therefore less biological available than the free Sb 2O 3 (see also Section 15). 3. Hazards identification Most important hazards:Hazard warning not required Specific hazards: Vapour and fumes released at elevated processing temperatures may be irritant for the eyes, the nose, the throat and the respiratory tract and in case of overexposure may cause nausea and headache. The material is not classified as being a dangerous preparation according to the EEC-Directive 88/379 and the subsequent amendments. See also Section 15.4. First-Aid measures Inhalation: When fumes of molten material have been inhaled;- Move person to fresh air as quickly as possible - rest in half upright position - loosen clothing - keep warm In case of respiratory problems move person to first aid station for medical treatment.Skin contact: Any molten material on the skin/burns should be cooled (off) as quickly as possible by means of cold water.Cover the wound with sterile cloth and move person to first aid station or hospital for medical treatment.Attention: never pull off the molten material from the wound.Eye contact: Any material entering the eye should be flushed out with copious volumes of water.Ingestion: No danger of toxicity, this material is biologically inactive (see also Section 11). 5. Fire-fighting measures Extinguishing media: Water, water/foam, CO 2, ABC fire extinguisher powder.Specific Hazards: Treat the material as a solid that can burn. Moulded parts or solid granules generally burn slowly with flaming drips.

材料物性表

Product Data Sheet CHARACTERISTICS TEST METHOD Physical Properties Specific Gravity ASTM D792 1.20 1.20 Mould Shrinkage ASTM D9550.1-0.3%0.001-0.003in/in Mechanical Properties Tensile Strength ASTM D63890MPa 13050psi Flexural Strength ASTM D790125MPa 18125psi Flexural Modulus ASTM D7906500MPa 943ksi Notched Izod Impact Strength (3.2mm) ASTM D256 85 J/m 1.6 ft-lb/in Thermal Properties Heat Deflection Temperature @ 1.82MPa (264 psi) ASTM D648145°C 293°F Electrical Properties Surface Resistivity ASTM D2571E15ohms 1E15ohms Description: Glass Fiber Reinforced Polypropylene PPR 40G NC702 Product Code: 5218702Internal Code: NATURAL Colour: Maxxam TM NOMINAL VALUE (SI)NOMINAL VALUE (ENGLISH)Flammability Properties Flame Rating @ 0.8mm Internal HB HB Processing Conditions PP Barrel Temperature 200-240 °C 392-464°F Mould Temperature 30-60 °C 86-140°F Drying Temperature 80-85 °C 176-185°F Drying Time 2-3 Hour 2-3 Hour Injection Pressure Hold Pressure Screw Speed Back Pressure Rev #: 0, Revision Date: 6/8/2010 PRINTED IN SHENZHEN LHM 33587 Walker Road,Avon Lake,Ohio 44012, USA, Tel 1-440-930 1000 WHEN YOU HAVE QUESTION WITH ENGINEERING PLASTICS, WE COMPOUND THE ANSWER. No.1, Qihang Industrial Park,Haoxiang Road, Shajing Town, Baoan,Shenzhen, P.R.China,Tel:86-755-29692888MODERATE MED-HIGH MED-HIGH THIS IS NOT A PRODUCT SPECIFICATION LOW THE INFORMATION PRESENTED HEREIN IS PRESENTED IN GOOD FAITH AND TO THE BEST OF OUR KNOWLEDGE IS TRUE AND ACCURATE. IT IS INTENDED AS A GUIDE AND IS OFFERED FOR USE AT YOUR DISCRETION AND RISK. POLYONE DOES NOT GUARANTEE RESULT AND DISCLAIM ANY LIABILITY INCURRED IN CONNECTION WITH THE USE OF THE PRODUCTS DESCRIBED OR THE INFORMATION PRESENTED Tel: 86-755-29692888