金育PA-758_物性表
台南縣仁德鄉三甲村59-1號
TEL: 886-6-266-5000 FAX: 886-6-266-5555~7
透明 ABS, POLYLAC? PA-758March 6, 2009V1W 材料規格︰
特性(Properties)
測試方法
(Test Method)
測試條件
(Test Condition)
單位(Unit) PA-758
引張強度Tensile Strength ASTM D638 1/8”, 6 mm/min
Kg/cm2
(lb/in2)
405
(5,740)
彎曲強度Flexural Strength ASTM D790 1/4”, 2.8 mm/min
Kg/cm2
(lb/in2)
550
(7,780)
彎曲彈性率Flexural Modulus ASTM D790 1/4”, 2.8 mm/min
Kg/cm2
(lb/in2)
19,000
(270,000)
IZOD 衝擊強度Izod Impact Strength ASTM D256
(Notched)
1/4”, 23℃ Kg-cm/cm 16
200, 5Kg
℃ 3.0
流動係數Melt Flow Index ASTM D1238
220, 10Kg
℃
g/10min
34
比重Specific Gravity ASTM D792 23℃ -
1.08
軟化點
Vicat Softening Temp. ASTM D1525 1/8”, 50/hr
℃()
℃℉105(221)
熱變形溫度
H.D.T. ASTM D648 1/4”, 120/hr
℃()
℃℉88(190)
濁度
Haze
ASTM D1003 1/8” - 4.0 光線透過率
Light Transmission
ASTM D1003 1/8” % 89 燃燒率
Flammability
UL 94 - - 1/16” HB 以上數據僅代表一般通用數據，不代表每一產品的規格值
物性材料表
特性Feature 耐高温、耐冲击、高流动性、尺寸稳定。High temperature resistance, impact resistance, high liquidity, dimension stability. 用途Use 电子、电器零件、汽车部件等。Electronic, electrical parts, auto parts, etc. 注塑条件Injection conditions 预干燥温度Pre-drying temperature 预干燥时间Pre-drying time 进料区温度Feed zone temperature 压缩区温度Compression zone temperature 熔融区温度Melting zone temperature 喷嘴温度Nozzle Temperature 模具温度Mold 注射压力Injection pressure 物理机械性能Physical and mechanical properties 项目Project 单位unit 试验方法Test method 数值Value 密度Density 熔点Melting point 成型收缩率Mold Shrinkage 吸水率（24小时，23℃）Water Absorption (24 hours, 23 ℃) 熔融指数Melt Index 阻燃等级Flame Rating 拉伸断裂强度Tensile Strength 拉伸模量Tensile modulus 断裂伸长率Elongation at break 弯曲强度Bending 弯曲模量Bending modulus 悬臂梁（无缺口）冲击强度Izod (unnotched) impact strength 悬臂梁缺口冲击强度Izod notched impact strength 洛氏硬度Rockwell hardness 热变形温度（0.45MPa）Heat Deflection Temperature（0.45MPa） Dielectric Strength 绝缘破坏强度 Arc resistance 耐电弧性 Dielectric Constant 介电常数 Dielectric Losses 介电损耗 Characteristics 特性 平衡吸湿量Moisture Absorption at Equilibrium 线性成型收缩率，横向Linear Mould Shrinkage, Transverse 断裂伸长率Elongation at Break 屈服伸长率Elongation at Yield
PA10T材料物性表
P ROVISIONAL D ATA S HEET G RIVORY HT G RIVORY XE 4027 BLACK 9916 Product description Grivory XE 4027 black 9916 is a 30% glass-fibre reinforced flame retardant (UL 94 V-0) engineering thermoplastic material based on a semicrystalline, partially aromatic co-polyamide. Grivory XE 4027 black 9916 is free of halogens and red phosphorus. RoHS: Grivory XE 4027 black 9916 is in compliance with RoHS (2002/95/EC, Re-striction of Hazardous Substances). WEEE:Parts produced from Grivory XE 4027 black 9916 are not subject to "selec-tive treatment" according the Directive 2002/96/EC on Waste Electrical and Elec-tronic Equipment. ISO polymer designation: PA 10T/X ASTM designation: PPA, polyphthalamide The main distinguishing features of Grivory HT-PPA, when compared to other poly-amides, are its good performance at high temperatures providing parts which are stiffer, stronger, have better heat distortion and dimensional stability as well as excel-lent chemical resistance and low moisture absorption. Grivory XE 4027 black 9916 is especially suitable for injection moulded components in electrical and electronic applications which require a flame class acc. UL 94 V-0. The material is suitable for lead-free SMT reflow soldering acc. i.e. JEDEC J-STD-020C (peak temperature 260°C). Compo-nents conforming to JEDEC MSL1 are achievable.
锂电材料物性对比
电池材料厂家技术标准积累 深圳市贝特瑞 MSG-S(518) 负极石墨粒径：D10=9.764；D50=17.136um；D90=28.189；水分:0.039;碳含量:99.952;TAP密度;1.036 比表面 积:2.784；首次容量/效率:363.51/94.18 深圳市贝特瑞 518 负极石墨粒径：D10=9.862；D50=16.888um； D90=28.374；水分:0.04%; 碳含量:99.962; TAP密度;1.042% 比表面积:2.625；首次容量/效率:352.3/92.5% 深圳市贝特瑞 AG 负极石墨粒径：D10=7.137；D50=18.058um； D90=37.495；水分：0.035;碳含量：99.676;TAP密度：1.001 首次容量/效率:320.83/90.42% 深圳市贝特瑞 AG 负极石墨粒径：D10=7.53；D50=17.779um； D90=39.648；水分：0.041;碳含量：99.743;TAP密度：1.002 ，首次容量/效率:326.51/90.67% 深圳市贝特瑞 SAG-23 负极石墨粒径：D10=8.318；D50=21.097um； D90=47.119；水分：0.04；碳含量：99.925；TAP密度：1.021 ，比表面积:4.605；首次容量/效率:332.11/92.08 深圳市贝特瑞 818 负极石墨粒径：D10=11.453；D50=18.226um； D90=28.762；水分：0.036；碳含量：99.964;TAP密度：1.121 比表面积:1.947;首次容量/效率:364.63/95.29% 深圳市贝特瑞 818 负极石墨粒径：D10=10.859；D50=18.033um；
材料物性表
EXTRUSION APPLICATION
Introduction Responsible for a long line of accomplishments in outstanding engineering plastics, UBE NYLON products have won the trust and respect of users the world over. UBE NYLON – NYLON 6, NYLON COPOLYMERS – is in wide use throughout industry with their unique properties utilized to their fullest potential. UBE NYLON 6 has a number of excellent properties as follows: Excellent in impact strength and rigidity Having a smaller friction coefficient, thus excellent in abrasion resistance Excellent in resistance to oils, solvents and chemicals Superior in heat resistance Appropriate to mass production, contributing to cost reduction Summary 1. Introduction 2. Nomenclature 3. Monofilament Applications 4. Film Applications 5. TERPALEX Polyamide 6/66/12 Copolymer Nomenclature The first 2 digits in the code indicate the type of Polyamide. The third and fourth digits indicate the molecular weight level for 1000 series. In case of copolymer, the third digit shows the viscosity level. The co-polymerization ratio can be roughly calculated from the fourth digit multiplying by 5. “T” means the basic grade for monofilament application and the grade contain some additives for maintain good process stability and high trans-parency. In case of “MT”, means monomer con-taining grade offering good flexibility and softness. 10: Polyamide 6 homopolymer 50: Polyamide 6/66 copolymer 70: Polyamide 6/12 copolymer Ex. 1022FDX04: : c.a. 22 x 1,000 = 22,000 Ex. 5034MTX1: : level = 3 (high viscosity) : c.a. 80/20(4 x 5 = 20et%) : monomer-contain type 2 Introduction
物性表
Safety Data Sheet complies with:directive 91/155/EEC revision:2.0 ISO 11014-1:Safety data sheet for chemical products. revision date:02/02/1998date of issue: 26/02/1998 p 1. Product and company identification Product name:Stanyl ?Product code:TE250F3 Manufacturer: DSM Engineering Plastics P.O. Box 43,6130 AA Sittard The Netherlands Emergency number: The Netherlands +31 (0)46 4 76 55 55 2. Composition/Information on ingredients This chemical product is a preparation Chemical nature:(poly)amide PA 46CAS number:50327-22-5Components contributing to the hazard: The material contains Sb 2O 3 as a synergist with an average content of max. 7%. Sb 2O 3 is classified as a harmful (Xn) substance with a risk phrase R40 carcinogen class 3. However, the Sb 2O 3 is embedded in an impervious matrix of polymer and is therefore less biological available than the free Sb 2O 3 (see also Section 15). 3. Hazards identification Most important hazards:Hazard warning not required Specific hazards: Vapour and fumes released at elevated processing temperatures may be irritant for the eyes, the nose, the throat and the respiratory tract and in case of overexposure may cause nausea and headache. The material is not classified as being a dangerous preparation according to the EEC-Directive 88/379 and the subsequent amendments. See also Section 15.4. First-Aid measures Inhalation: When fumes of molten material have been inhaled;- Move person to fresh air as quickly as possible - rest in half upright position - loosen clothing - keep warm In case of respiratory problems move person to first aid station for medical treatment.Skin contact: Any molten material on the skin/burns should be cooled (off) as quickly as possible by means of cold water.Cover the wound with sterile cloth and move person to first aid station or hospital for medical treatment.Attention: never pull off the molten material from the wound.Eye contact: Any material entering the eye should be flushed out with copious volumes of water.Ingestion: No danger of toxicity, this material is biologically inactive (see also Section 11). 5. Fire-fighting measures Extinguishing media: Water, water/foam, CO 2, ABC fire extinguisher powder.Specific Hazards: Treat the material as a solid that can burn. Moulded parts or solid granules generally burn slowly with flaming drips.
常用材料的热物性参数
表1 各种金属的热物性值 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相 线、固相线温度 (C) =7.88(20C) =7.3(1500C) =7.0(1600C) =7.86(15C) =7.86(15C) =7.85(15C) =7.85(15C) =7.83(15C)
续表1 各种金属的热物性值 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相 线、固相线温度 (C) =7.73(15C) Ts=1488 T L=1497 =7.84(15C) T S=1420 T L=1520 =7.7(15C) 13.1Cr,0.5Ni T S=1399 T L=1454 =7.0(15C) 比热相对于 普通铸铁
=7.1(15C) 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相 线、固相线温度 (C) =7.5~7.8(15C) =8.92 T S=T L=1083
s=2.70(15C) T S=T M=660.2 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相 线、固相线温度 (C) s=1.74 T L=T S=651 s=6.09 T S=1395 T L=1427
表2 铸型的热物性计算公式
硅砂，干型，呋喃铸型600C以下 0.385<<0.494 0.0058 Product Data Sheet CHARACTERISTICS TEST METHOD Physical Properties Specific Gravity ASTM D792 1.20 1.20 Mould Shrinkage ASTM D9550.1-0.3%0.001-0.003in/in Mechanical Properties Tensile Strength ASTM D63890MPa 13050psi Flexural Strength ASTM D790125MPa 18125psi Flexural Modulus ASTM D7906500MPa 943ksi Notched Izod Impact Strength (3.2mm) ASTM D256 85 J/m 1.6 ft-lb/in Thermal Properties Heat Deflection Temperature @ 1.82MPa (264 psi) ASTM D648145°C 293°F Electrical Properties Surface Resistivity ASTM D2571E15ohms 1E15ohms Description: Glass Fiber Reinforced Polypropylene PPR 40G NC702 Product Code: 5218702Internal Code: NATURAL Colour: Maxxam TM NOMINAL VALUE (SI)NOMINAL VALUE (ENGLISH)Flammability Properties Flame Rating @ 0.8mm Internal HB HB Processing Conditions PP Barrel Temperature 200-240 °C 392-464°F Mould Temperature 30-60 °C 86-140°F Drying Temperature 80-85 °C 176-185°F Drying Time 2-3 Hour 2-3 Hour Injection Pressure Hold Pressure Screw Speed Back Pressure Rev #: 0, Revision Date: 6/8/2010 PRINTED IN SHENZHEN LHM 33587 Walker Road,Avon Lake,Ohio 44012, USA, Tel 1-440-930 1000 WHEN YOU HAVE QUESTION WITH ENGINEERING PLASTICS, WE COMPOUND THE ANSWER. No.1, Qihang Industrial Park,Haoxiang Road, Shajing Town, Baoan,Shenzhen, P.R.China,Tel:86-755-29692888MODERATE MED-HIGH MED-HIGH THIS IS NOT A PRODUCT SPECIFICATION LOW THE INFORMATION PRESENTED HEREIN IS PRESENTED IN GOOD FAITH AND TO THE BEST OF OUR KNOWLEDGE IS TRUE AND ACCURATE. IT IS INTENDED AS A GUIDE AND IS OFFERED FOR USE AT YOUR DISCRETION AND RISK. POLYONE DOES NOT GUARANTEE RESULT AND DISCLAIM ANY LIABILITY INCURRED IN CONNECTION WITH THE USE OF THE PRODUCTS DESCRIBED OR THE INFORMATION PRESENTED Tel: 86-755-29692888 DuPont ? Zytel ? nylon resin Zytel ? 101L NC010 Value DAM 50%RH Identification Resin Identification ISO 1043PA66 Part Marking Code ISO 11469>PA66< Mechanical Yield Stress ISO 527MPa (kpsi) 82 (11.9)55 (8.0) Strain at Break ISO 527% 50mm/min 45 Nominal Strain at Break ISO 527%25>100 Yield Strain ISO 527% 4.525 Tensile Modulus ISO 527MPa (kpsi)3100 (450) 1400 (200) Tensile Creep Modulus ISO 899 MPa (kpsi) 1h 1400 (200) 1000h 820 (119) Poisson's Ratio 0.41 Flexural Modulus ISO 178MPa (kpsi)2800 (410) 1200 (174) Notched Charpy Impact Strength ISO 179/1eA kJ/m 2 -30°C (-22°F) 4.53 23°C (73°F) 5.515 Unnotched Charpy Impact Strength ISO 179/1eU kJ/m 2 -30°C (-22°F)400NB 23°C (73°F) NB NB Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated. The DuPont Oval Logo, DuPont?, The miracles of science? and Zytel? are trademarks or registered trademarks of DuPont Company. Copyright? 2005. 050630/050630 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body. For other medical applications see "DuPont Medical Caution Statement", H-50102. https://www.wendangku.net/doc/e816452622.html, Zytel ? 101L NC010 is a lubricated polyamide 66 resin for injection molding. Property Test Method Units 塑膠原材料物性表 材料名稱密度收縮率成本USD/kg燃燒狀態料管溫度射出壓力 (Kg/cm2)模溫 (C°)用途ABS (BK) 1.42~2.4 ABS (HB COLOR) 1.05 1.42~1.75/450 ABS (HB GF10) 1.2 1.75~3.72/about 500 ABS (HB GF20) 1.220.002 2.19/60-80 ABS (HB GF30) 2.25~4.26/ ABS (Natural) 1.25~2.4/ ABS (PA/757BK) 1.53~1.75/ ABS (PA/765AB) 2.2/ ABS (V0 GF10) 1.2 3.86/about 500 ABS (V0) 1.05 1.42~2.11 ABS (透明) 1.96~2.06 ABS (Acrylonitrile Butadiene Styrene)丙烯睛-丁二烯-苯乙烯1.05~1.1 0.005 1.25~2.4 易燃, 暗黃,有黑煙. 軟 化.特有氣味. 硬, 脆. 金 屬聲 180~260450~210050~80 電器,日用品外殼,玩具,家具,運動用品,燈 飾,汽車配件 AS (GF20) 1.260.002210-28060-80 AS=SAN(Styrene-Acrylonitrile Copolymer)丙烯睛-苯乙烯1.06 0.004/190~280 700~2300 40~80 食具,日用品,透明裝飾面,主表面 EPS 發泡膠 Expanded PolyStyrene貨品包裝,絕緣板, 裝飾品 EVA 乙烯-醋酸乙烯共聚物. Ethlene-Vinyl Acetate Copolymer橡皮膠120~25030~50鞋底,吹氣玩具製品,包裝膠膜 HIPS (BW-4(H45))/ HIPS (HB) 高衝擊聚苯乙烯 High Impact PS/ 1.1~1.3/ HIPS (PA-765BK) 2.2耐沖擊.玩具,日用品,收音機殼,電視機殼. HIPS (V0)/ 1.55 PA +GF30 (V0)260~29050~90 PA 66 (HB)/250~31050~90噪音小,軟. 牙刷,線圈架, 拉絲,束帶,齒輪,電動玩具外殼,電器配件,運動用品 PC(GE10G15) 5.508/ PC(GF40) 1.820.15%270-31080-120 PC(HB) 3.63 PC(L-1250YN) 1.2 3.7/ PC(N) 聚碳酸脂. 防彈膠 Polycarbonate 1.2 0.60% 4.2~4.75 稍難燃, 黃色焰,黑煙. 軟化. 特有味 260~300 (330劣化) 700~2100 85~120 咖啡壺,電動工具外殼,安全頭盔,透明片, 防硬玻璃,電器零件 PC(透明) 4.0~4.2 PC+ABS 2.32~2.98 PC+ABS (FR2000, V0) 4.485215~240about 75060~80 PC+ABS (KU2-1468,V0)240~280about 75060~90 材料名稱密度收縮率成本USD/kg燃燒狀態料管溫度射出壓力 (Kg/cm2)模溫 (C°)用途 PE 聚乙烯1.14 0.45% 易燃, 尖端黃,下端藍. 邊滴邊燃. 石腊燃燒味170-25040-60 PE (Polyethlene)0.95 3.50%150-23020-40包裝膠袋,膠瓶,水桶,電線,大貨桶,玩具PE(High Density PE) 高密160~310700~140025~70包裝膠袋,膠瓶,膠花,電線,大貨桶,玩具PE(Low Density PE) 低密150~310600~140025~70包裝膠袋,膠瓶,水桶,電線,大貨桶 常用溶剂 一、乙醇（ethyl alcohol，ethanol）CAS No.：64-17-5 （1）分子式 C2H6O （2）相对分子质量 46.07 （3）结构式 CH3CH2OH， （4）外观与性状：无色液体，有酒香。 （5）熔点（℃）：-114.1 （6）沸点（℃）：78.3 溶解性:与水混溶，可混溶于醚、氯仿、甘油等多数有机溶剂; 密度：相对密度(水=1)0.79;相对密度(空气=1)1.59; 稳定性:稳定;危险标记7(易燃液体); 主要用途:用于制酒工业、有机合成、消毒以用作溶剂 不同压力下乙醇物性参数变化 二、甲醇（methyl alcohol，Methanol）CAS No.：67-56-1 （1）分子式 CH4O （2）相对分子质量32．04 （3）结构式 CH3O， （4）外观与性状：无色澄清液体，有刺激性气味。 （5）熔点（℃）：-97.8，凝固点-97．49℃，沸点64．5℃．闪点(开口)16℃，燃点470℃，折射率1. 3285，表面张力22．55×10-3N／m （6）相对密度(20 ℃／4℃)0．7914 溶解度参数δ＝14．8，能与水、乙醇、乙醚、丙酮、苯、氯仿等有机溶剂混溶，甲醇对金属特别是黄铜有轻微的腐蚀性。易燃，燃烧时有无光的谈蓝色火焰。蒸气能与空气形成爆炸混合物．爆炸极限6．0％-36．5％(vol)。纯品略带乙醇味，粗品刺鼻难闻。有毒可直接侵害人的肢体细胞组织．特别是侵害视觉神经网膜，致使失明。正常人一次饮用4一10g 纯甲醉可产生严重中毒。饮用7-8g可导致失明，饮用30-100g就会死亡。空气中甲酵蒸气最高容许浓度5mg／m3。 不同压力下甲醇物性参数变化 表1 各种金属的热物性值 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相线、固相线温度 (C) =7.88(20C) =7.3(1500C) =7.0(1600C) =7.86(15C) =7.86(15C) =7.85(15C) =7.85(15C) =7.83(15C) 续表1 各种金属的热物性值 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相线、固相线温度 (C) =7.73(15C) Ts=1488 T L=1497 =7.84(15C) T S=1420 T L=1520 =7.7(15C) 13.1Cr,0.5Ni T S=1399 T L=1454 =7.0(15C) 比热相对于 普通铸铁 =7.1(15C) 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相线、固相线温度 (C) =7.5~7.8(15C) =8.92 T S=T L=1083 s=2.70(15C) T S=T M=660.2 温度 C 比热 cal/(g·C) 导热系数 cal/(cm·s· C) 密度(g/cm3)液相线、固相线温度 (C) s=1.74 T L=T S=651 s=6.09 T S=1395 T L=1427 表2 铸型的热物性计算公式 硅砂，干型，呋喃铸型600C以下 0.385<<0.494 0.0058 名称规格：POM FG2025 产地：韩国工程料 特性： 提供方：东莞东扬塑胶T E L：1 3 6 /8 6 6 5/6 6 6 1 ①原料描述部分 规格级别：--- 外观颜色：--- 用途概述：--- 备注说明：特性：玻纤填充Glass Fiber ②原料技术数据 性能项目试验条件[状态] 测试方法测试数据数据单位基本性能 吸水率23℃，60%RH ASTM D-570 0.20 % 熔体流动速率--- ASTM D-1238 9 g/10min 物理性能 填充材料含有率--- --- 25 % 比重--- ASTM D-792 1.59 --- 机械性能拉伸强度23℃ASTM D-638 1450 kgf/cm2 伸缩率23℃ASTM D-638 3 % 弯曲强度23℃ASTM D-790 2100 kgf/cm2 曲折弹性率23℃ASTM D-790 8.80 ×104kgf/cm2断裂强度2mmt ASTM D-732 760 kgf/cm2 IZOD冲击强度Notch 3.2mmt ASTM D-256 10 kgf.cm/cm 拉伸冲击强度 3.2mmt Stype ASTM D-1822 180 kgf.cm/cm2洛氏硬度M scale ASTM D-785 M95 --- 电气性能表面电阻率--- ASTM D-257 1×1016Ω 体积电阻率--- ASTM D-257 1×1014Ω.cm 耐电压--- ASTM D-149 23 KV/mm 加工性能成型收缩率3mmt,直径100mm --- 0.5 % 热性能 燃烧性0.8mmt UL 94 HB --- 熔点10℃/min DSC Method 165 oC 常用材料物性表 清洗要求 压力速度 ABS 210℃-245℃90℃≥2H 25℃-75℃中高压中高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 压中速正常温度下材料也会分解，停机十分钟需排料。 ABS+玻纤220℃-250℃90℃≥3H 50℃-80℃中高压中高速正常温度下材料也会分解，停机十分钟需排料。 ABS+AS 220℃-240℃90℃≥3H 60℃-85℃中高压中高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 ABS+PC 240℃-280℃110℃≥4H 50℃-100℃中高压高速长期高温下材料会分解，正常温度下半小时后需排料。 PA6 240℃-270℃105℃≥8H 80℃-90℃中高压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 PA6+玻纤250℃-280℃110℃≥8H 80℃-90℃中高压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 PA12 240℃-290℃85℃≥5H 30℃-40℃中压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 PA12+玻纤240℃-270℃85℃≥5H 80℃-90℃中压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 PA66+玻纤260℃-280℃105℃≥12H 70℃-90℃中压高速高温下材料会分解，正常温度下半小时后需清洗螺杆。 PBT 240℃-270℃140℃≥4H 25℃-50℃中压高速长期高温下材料会分解，正常温度下半小时后需排料。 PBT+玻纤240℃-265℃140℃≥4H 25℃-50℃中压高速长期高温下材料会分解，正常温度下半小时后需排料。 PC 260℃-300℃120℃≥4H 70℃-120℃高压高速、低速无需清洗，320℃高温下不会分解，如出现变色需排料。 PC+玻纤250℃-290℃125℃≥4H 70℃-120℃高压高速无需清洗，280℃高温下不易分解，如出现变色需排料。 PC+PBT 235℃-285℃130℃≥4H 35℃-95℃中高压高速长期高温下材料会分解，正常温度下半小时后需排料。 PE-HD 200℃-230℃/ / 50℃-95℃低压高速无需清洗，高温下不会分解，长期高温下流动性会增加。 PE-LD 180℃-220℃/ / 20℃-40℃中高压高速无需清洗，高温下不会分解，长期高温下流动性会增加。 PEI 340℃-400℃150℃≥4H 100℃-175℃中高压高速无需清洗，高温下不易分解，正常温度下半小时后需排料。 PEI+玻纤340℃-420℃150℃≥4H 100℃-175℃中高压高速无需清洗，高温下不易分解，正常温度下半小时后需排料。 PA12 聚酰胺12或尼龙12 化学和物理特性 PA12是从丁二烯线性，半结晶-结晶热塑性材料。它的特性和PA11相似，但晶体结构不同。 PA12是很好的电气绝缘体并且和其它聚酰胺一样不会因潮湿影响绝缘性能。它有很好的抗冲击性机化学稳定性。PA12有许多在塑化特性和增强特性方面的改良品种。和PA6及PA66相比，这些材料有较低的熔点和密度，具有非常高的回潮率。PA12对强氧化性酸无抵抗能力。 PA12的粘性主要取决于湿度、温度和储藏时间。它的流动性很好。收缩率在0.5%到2%之间，这主要取决于材料品种、壁厚及其它工艺条件。 注塑模工艺条件 干燥处理：加工之前应保证湿度在0.1%以下。如果材料是暴露在空气中储存，建议要在85C热空气中干燥4~5小时。如果材料是在密闭容器中储存，那么经过3小时温度平衡即可直接使用。 熔化温度：240~300C；对于普通特性材料不要超过310C，对于有阻燃特性材料不要超过270C。 模具温度：对于未增强型材料为30~40C，对于薄壁或大面积元件为80~90C，对于增强型材料为90~100C。增加温度将增加材料的结晶度。精确地控制模具温度对PA12来说是很重要的。 注射压力：最大可到1000bar（建议使用低保压压力和高熔化温度）。 注射速度：高速（对于有玻璃添加剂的材料更好些）。 流道和浇口:对于未加添加剂的材料，由于材料粘性较低，流道直径应在30mm左右。对于增强型材料要求5~8mm的大流道直径。流道形状应当全部为圆形。注入口应尽可能的短。可以使用多种形式的浇口。大型塑件不要使用小浇口，这是为了避免对塑件过高的压力或过大的收缩率。浇口厚度最好和塑件厚度相等。如果使用潜入式浇口，建议最小的直径为0.8mm。 热流道模具很有效，但是要求温度控制很精确以防止材料在喷嘴处渗漏或凝固。如果用热流道，浇口尺寸应当比冷流道要小一些。 典型用途 水量表和其他商业设备，电缆套，机械凸轮，滑动机构以及轴承等。 ABS 丙烯腈-丁二烯-苯乙烯共聚物 化学和物理特性 ABS是由丙烯腈、丁二烯和苯乙烯三种化学单体合成。每种单体都具有不同特性：丙烯腈有高强度、热稳定性及化学稳定性；丁二烯具有坚韧性、抗冲击特性；苯乙烯具有易加工、高光洁度及高强度。从形态上看，ABS是非结晶性材料。三中单体的聚合产生了具有两相的三元共聚物，一个是苯乙烯-丙烯腈的连续相，另一个是聚丁二烯橡胶分散相。ABS的特性主要取决于三种单体的比率以及两相中的分子结构。这就可以在产品设计上具有很大的灵活性，并且由此产生了市场上百种不同品质的ABS材料。这些不同品质的材料提供了不同的特性，例如从中等到高等的抗冲击性，从低到高的光洁度和高温扭曲特性等。ABS材料具有超强的易加工性，外观特性，低蠕变性和优异的尺寸稳定性以及很高的抗冲击强度。 注塑模工艺条件 干燥处理：ABS材料具有吸湿性，要求在加工之前进行干燥处理。建议干燥条件为材料物性表
物性表
各种塑料基本物性表
常见物性参数表
常用材料的热物性参数
POM FG2025物性表
常用材料物性表
材料物性表