维修术语
(灯)不亮not come on 不可用not serviceable
“工”型type I 不锈钢stainless steel
APU 舱门APU bay door 部件part
T 型件Tee extrusion 材料material
阿罗钉alodine 参考reference
安全带safety belt 餐板feed panel
安装install 餐车diner
安装座attach fitting 操纵control
按钮button 操作检查operational
按需要as required 槽spout
凹槽notch 侧板sidewall
凹坑dent 测量measure
把手,扶手handle 测试test
包皮cowl 插钉pin
保护层coating 插头plug
保险fuse 插座receptacle
报废discard 拆下remove
报告工程师report to engineer 长桁stringer
杯子cup 超标out of limit
比率转换器ratio changer 超标exceed the limit
壁橱closet 超过exceed
边缘edge 超控手柄override handle
便于检查easily to inspect 彻底修理drastically repair 变形deformation (n) 陈旧的worn
变形deform (v) 衬板liner
变压器transformer 衬套bush
标牌placard 成型shaping
标识sign 乘务员attendant
标志instruction 尺寸size
玻璃pane 充足的sufficient
玻璃纤维fiberglass 冲水按钮flush button
补片patch 冲洗flush
补片filler 冲压ram
冲压空气ram air 低压压气机LP-compressor
抽油defuel 底部bottom
出口exit 底盘base
除腐区reworked area 底漆primer
厨房galley 底座(结构件)mounting
厨房烤箱galley oven 底座(螺母)plate
储物柜closet 底座(天线)base
处理treatment 地板梁floor beam
处理dispose 地面ground
传感器sensor 地毯carpet
传输transmission 第二层two layer
垂直的vertical 点火电嘴ignitor
存放处location 电路circuit
错位migration 电门,开关switch
搭地线jumper 电气electrical
搭接处interface 电气接地ELEC bonding
搭接片splice strap 电源通电power
搭接片splice 电子avionics
打磨blend out 电子架 E rack
打磨片blent disk 电子架shelf
打止裂孔drill stop hole 电阻elec resistance 大翼wing 电阻resistance
大于more than 垫片washer
单向活门check-valve 吊仓nacelle
弹簧片spring seal 吊点mount cone
挡块retainer 调节adjust
挡雨板fender 调整片tap
导线wire 顶板ceiling
灯light 顶部top
灯泡bulb 顶部overhead
灯泡lamp定中弹簧decentering spring
灯箱light case 丢失miss
灯罩light lens 堵盖plug
登机门ENTRY DOOR 堵塞clog
端头ending 腐蚀corrosion
段section 腐蚀corrode
断break 附件(大)accessary
断开disconnect 附件(小)attach
断裂fracture 附近adjacent to
断裂的broken 复合complex
断丝,磨损fray 副驾驶员做椅first offcer's seat 锻件forged part 副翼aileron
多处numerous 改装modification
发动机engine 盖cap
翻新overhaul 杆rod
反光镜mirror 钢丝steel
方向舵rudder 钢索cable
防冰管anti-ice duck 割除cut out
防腐corrosion-inhibition割断,割下cut off
防静电static-free隔板clapboard,partition
防磨条wear strip 隔框bulkhead
防滞antiskid 隔热棉insulation-blanket
防撞灯anti-collision light 隔栅grille
放extend 各有each has
放电刷discharger 根据方案in according to disposition
分层delamination 根据监控指令单condition monitor order…
风层,脱胶delaminate 更换replace
风挡windshield 工程师engineer
风挡玻璃windscreen 功能测试functional test
风扇整流罩FAN COWL 功能检查functional
风蚀erode 供应系统feed system
封严sealing 供油管OIL TUBE
封严条seal 鼓轮drum
蜂窝芯stagger core 鼓起bulge
扶手armrest 固定secure
扶手盖板armrest cover 固化harden
辅助滑轨assistant track 固化剂hardener
故障fault 划痕,划伤scratch
刮伤scratch 划窝countersink
挂attach 环氧树脂epoxy resin
挂钩hook 恢复restore
挂上hang up 活动窗slide window
关上close 活门valve
观察镜view glass 货舱cargo compt
观察镜viewer 机构mechanism
观察员observer 机身fuselage
观察员observer 迹象mark
光滑地smoothly 加强doubling
滚轮roller 加强件stiffener
过道aisle 加强块doubler
过期expire 加强肋intercostal
过热传感元件overheat sensing element 加强修理reinforcement 海绵sponge 加温导线hot wire
焊接weld 加油面板refuel panel
焊条welding rod 加油站面板fueling station panel
恒速传动装置CSD case 夹子clip
横梁latitudinal beam 驾驶舱cockpit
横向lateral 间隙gap
后端rear 减速板speedbreak
后缘T/E 减压器reducer
厚度thickness 减震器shock absorber
呼叫灯call light 减震支柱shock strut
护板protect strap 检查inspect
护目镜goggles 检修门access door
护罩shroud 胶sealant
花键spline 胶带tape
滑轨track胶垫mat
滑轮pulley 胶垫圈rubber washer
滑丝cross thread 胶套rubber
滑梯罩slide cover 胶纸tape
滑油量oil lever 角材angler
角型件angle shape 喇叭megaphone
脚登板pedal 拦网block
铰链hinge 牢固性security
接地点ground point 老化aged
接耳lug 老化,退化deteriorate
接通,提供supply 雷达罩radome
接头fitting 肋rib
接线管splice 离合器clutch
接线片terminal lug 立柱pole
结构的structural 例行routine
金属屑metal particle 连杆link
襟翼flap 连接attatch
紧固件fastener 连接板attach plate
紧急出口exit 连接口coupling
进气道inlet duct 连接销lockwire
进气口inlet port 联锁interlock
径向驱动轴radial drive shaft 裂crack
静电,静压static 另一个another
救生衣lifevest 龙骨梁keel beam
咖啡壶coffee maker 滤网filter
卡箍clamp 铝箔foil
卡环collar 轮舱wheel well
开口销cotter pin 轮子wheel
靠背back panel 逻辑logic
壳体case 螺钉screw
可用available 螺钉孔screw hole
客舱cabin 螺杆bolt
空气循环隔栅air return grille 螺帽nut 口port 螺套insert
块piece 螺纹压伤cross threading
框架frame 马桶toilet
垃圾箱dustbin 慢车IDLE
拉紧pull 毛刺bur
毛胚件rough 破损damage
铆钉rivet 漆层coating
门槛sill 其中之一one of
门框door frame 启动活门start valve
蒙皮skin 启动机starter
密度density 起落架landing gear
密度计densitometer 气瓶cylinder
面板panel 千层片shim
面漆enamel 前厕所fwd lav
模糊blur 前缘L/E
模糊不清obscure 腔体cavity
磨损wear 墙纸wallpaper
目视visual 切口cutout
内侧interior board 勤务面板service panel 内层inner 轻度light
尼龙搭扣nylon fastener 轻微slight
尼龙扣nylon hook 清洁clean
拧紧tighten 清洁剂cleaner
扭力管torsional tube 区域zone
扭曲kink 曲柄crank
排row 去除深度remove depth
排放drain 去毛刺deburr
排水槽gutter 缺口nick
排水管drain tube 群边skirt edge
配平trim 燃油fuel
喷漆paint燃油泵fuel pump
喷砂sand blast 扰流板spoiler
皮带,片strap 热水器water boiler
皮托管pitot 人工行程限制manual travel limit 偏航阻尼器yaw damper 日光灯daylight lamp 平衡机构equalizer 软管,软护套hose
平滑的,使平滑smooth 润滑剂lubricant
平行balance 三段three section
散装bulk 逃离滑梯escape slide
刹车brake 天花板ceiling
上表面upper surface 天线antenna
上述above 填补fill
深度depth 跳开关breaker
渗漏leakage 凸轮cam
升降舵elevator 图纸DWG
绳rope 涂,粘贴apply
失效inoperative 退漆strip paint
湿安装wet installed 退色badly faded
试车run up 托板pallet
释压pressure-release 托板螺帽plate nut 收retract 脱开disengage
收发机tranceiver外outer
手柄towing lever 外侧outer board
手册manual 完成complete
手电torch 完成finish
手工handwork万向接头gimbal
手提的portable 维护maintain
手提灭火瓶extinguish bottle 尾部tail
树脂resin 尾舱tail compartment
双倍double 尾喷管exhaust nozzle
水平安定面horizontal stabilizer 尾锥TAIL CONE 撕裂tear 位置locate
伺服servo 温度temp
松动,松脱loose 涡杆jackscrew
送修send to repair 涡杆worm bolt
塑料plastic 涡轮turbine
随动盖板hinge access door 污染物contamination 锁lock 污物dirt
锁定lockout 无线电高度表radio altimeter
锁扣latch 稀释剂thinner
锁销lockpin 铣mill
系统system 溢出spill
下部lower 翼尖tip
下角LWR corner 翼间wing tip
下位锁downlock 翼梁spar
下陷concave 引进introduce
下缘条chord 引孔make guiding hole
纤维板fibre board 引孔drill hole
相关的relative 引气bleed
相磨chafe 引气管bleed hose
消音板accoustic panel 应急emergency
销子pin 永久性修理permanence repair
楔形块wedge 用…填补fill it up with…
信号灯annunciator 油封preservation
行李架luggage-rack 油箱fuel tank
行李箱stowage 游动梁walk beam
修边reform 雨刮wiper
修理repair 语音记录器voice recorder
锈蚀rust 预冷器precooler
循环cycle 预位ARM
压紧gland 原厚度original thickness
压力通风系统plenum system 原来originally 压条cover 阅读灯reading light
严重的serious 允许损伤allowable damage
阳极化anodize 杂志袋literature container
氧气oxygen 载荷调整preload adjust
氧气面罩oxygen mask 再循环recirculation
液压HYD 在位be in place
液压泵HYD PUMP 脏dirty
液压管HYD duct 增压pressurization
液压系统hydraulic system 增压泵boost pump
液压油管组件TUBE ASSY 粘贴bond
液压油箱hydraulic reservior 照明illuminate
移到move to 遮阳板shade
真空泵vacuum pump 自动刹车autobrake
拯救salvation 自动油门auto thrust
整流罩fairing 自锁螺帽jam nut
整流锥spinner 自由移动move freely
整形rework 总管manifold
正常normal 纵梁longeron
正常位置normal position 纵向longitudial
正驾驶员座椅captain's seat 阻力支柱drag strut
之间between 组件assembly,pack
支撑架bracket 组件(电气) unit
支撑座support mount 组件(机械) assy
支架bracket 最薄min thickness
支拄support 作动筒actuator
止动固定块stop block 坐垫cushion
止动块atopper 座椅seat
指点信标marker beacon antenna 注意caution
指示indication转接器adapter
制作fabricate 转弯灯runway turnoff light
中厕所mid lav 转向turn
中间,中央center 装饰条trim strip
周围around 准备prepare
轴shaft 着陆灯landing light
轴承bearing 自动关闭auto close
主轮main wheel 助推机构扳机power assist trigger
Categories of Defect
Categories of defect depends on experience of maintenance practice .In this manual, the default Method used to categorize the defect found on the aircraft into four areas. Structure defect , Material defect, Common parts and Components defect and General defect.
缺陷分类
缺陷的分类一般依照维修实践中的经验来分。在本手册中,我们将缺陷分为四类:结构缺陷、材料缺陷、零部件缺陷和一般性缺陷。
1. Common Structure Defects Terms
结构缺陷术语
凹坑(1)dent
凹槽(2)notch
变形(3)deform
划痕(4)nick
点腐蚀(5)pitting
断裂(6)broken
腐蚀(7)corrode
划伤(8)scratch
裂纹(9)crack
毛刺(10)butt
磨损(11)chafe
凸起(12)protrude
凹陷(13)sag
粗糙(14)rough
漆层剥落(15)finish missing
褪色(16)fade
积水(17)entrapped water
2. Common material defect terms
材料缺陷术语
Material is divided in two categories: metallic and non-metallic. 材料分为两类:金属材料及非金属材料
1)Common metallic defect:
一般性金属材料缺陷:
氧化(18)oxidize
划伤(8)scratch
扭曲(19)distort
跷起(20)not in contour
穿孔(21)puncture
碎屑(22)chip
腐蚀(7)corrode
磨损(11)chafe
变形(3)deform
风蚀/风化(23)erode
裂纹(9)crack
2) Common non-metallic defect:
一般性非金属材料缺陷:
发霉(24)mildew
分层(25)delaminate
风蚀/风化(23)erode
裂纹(9)crack
老化(26)deteriorate
起皱(27)wrinkle
受潮(28)saturated
建筑专业常用英语词汇
建筑专业常用英语词汇 A design basis 设计依据 计划建议书planning proposals 设计任务书design order 标准规范standards and codes 条件图information drawing 设计基础资料basic data for design 工艺流程图process flowchart 工程地质资料engineering geological data 原始资料original data 设计进度schedule of design B stage of design 设计阶段 方案scheme, draft 草图sketch 会谈纪要summary of discussion 谈判negotiation 可行性研究feasibility study 初步设计preliminary design 基础设计basic design 详细设计detail design 询价图enquiry drawing 施工图working drawing, construction drawing 竣工图as built drawing C climate condition 气象条件 日照sunshine 风玫瑰wind rose 主导风向prevailing wind direction 最大(平均)风速maximum (mean) wind velocity 风荷载wind load 最大(平均)降雨量maximum (mean) rainfall 雷击及闪电thunder and lightning
材料专业英语常见词汇(一) Structure ['str?kt??]组织 Ceramic [si'r?mik]陶瓷 Ductility [d?k'til?ti] 塑性 Stiffness ['stifnis]刚度 Grain [ɡrein]晶粒 Phase [feiz]相 Unit cell 单胞 Bravais lattice 布拉菲['l?tis]布拉菲点阵 Stack [st?k]堆垛 Crystal ['krist?l] 晶体 Metallic crystal structure [mi't?lik, me-]金属性晶体点阵Non-directional [,n?ndi'rek??n?l, -dai-]无方向性 Face-centered cubic ['kju:bik]面心立方 Body-centered cubic 体心立方Hexagonal close-packed [hek's?ɡ?n?l]['kl?us'p?kt]密排六方Copper ['k?p?] 铜 Aluminum [?'lju:min?m]铝 Chromium ['kr?umj?m]铬 Tungsten ['t??st?n]钨 Crystallographic Plane [,krist?l?u'ɡr?fik][plein]晶面Crystallographic direction 晶向 Property ['pr?p?ti] 性质 Miller indices ['indisi:z]米勒指数 Lattice parameters ['l?tis][p?'r?mit?]点阵参数 Tetragonal [te'tr?ɡ?n?l]四方的 Hexagonal [hek's?ɡ?n?l]六方的 Orthorhombic [,?:θ?'r?mbik]正交的Rhombohedra [,r?mb?u'hi:dr?] 菱方的 Monoclinic [,m?n?u'klinik]单斜的 Prism ['prizm]棱镜 Cadmium ['k?dmi?m]镉 Coordinate system [k?u'?:dinit, k?u'?:dineit]坐标系Point defect ['di:fekt, di'f-, di'fekt]点缺陷Lattice ['l?tis]点阵 Vacancy ['veik?nsi]空位 Solidification [,s?lidifi'kei??n]结晶 Interstitial [,int?'sti??l]间隙 Substitution [,s?bsti'tju:??n]置换 Solid solution strengthening [s?'lju:??n]['stre?θ?n, 'stre?kθ?n] 固溶强化
外贸常用英语 一、常用名词 舱位申请单/托运单(Booking Note/Form/Sheet) 装货单(Shipping Order, S/O,也称作配载通知,订舱确认单Booking Confirmation) 提货单(Delivery Order, D/O) 一般原产地证明(Certificate of Origin, C/O) 普惠制原产地证明(Generalized System of Preferences Certificate of Origin Form A,又称G.S.P证书,Form A证书) 报关(Customs clearance) 报关单(Customs declaration)、 外贸合同、销售确认书(Sales Confirmation)、采购确认书(Purchased Confirmation) 形式发票(Proforma Invoice)、商业发票(Commercial Invoice )、海关发票(Customs invoice)、 装箱单(Packing List)、重量单(Weight List) 提单(Bill Of Lading)、空运提单(Air Way Bill, AWB)、海运提单(Ocean Bill of Lading) 信用证(Letter Of Credit) 银行保函(Letter of Guarantee, L/G) 汇票(Draft)、本票(Promissory Note)、支票(Cheque, Check) 受益人证明(Beneficiary,s Certificate) 船公司证明(Shipping company’s certificate ) 保险单((Insurance)Policy)、保险凭证(Insurance Certificate) 海运险:平安险(FPA)、水渍险(WPA)、一切险(All Risks) 陆运险:陆运险(Overland Transportation Risks)、陆云一切险(Overland Transportation All Risks) 航空险:空运险(Air Transportation Risks)、空运一切险(Air Transportation All Risks) 邮包险:邮包险(Parcel Post Risks)、邮包一切险(Parcel Post All Risks) 纸箱(Carton, CTN,CTNS)、托盘(Pallet)、木箱(Wooden case)、铁箱(Iron Case)、布包(Bale)、裸装(nude (packed))、木质包装(WOOD PACKING MATERIAL)、无木质包装(NO WOOD PACKING MATERIAL) 唛头(Marks and Nos.) 截补料时间,截文件时间(SI CUT OFF TIME) 进口关税 (import tariff) 增值税(value added tax, VAT) 消费税(consumer tax; consumption tax) 集装箱(Container)、船东柜(Container of Carrier)、货主柜(Shipper Own Container) 整箱(Full Container Load, FCL)、拼箱(Less Than Container Load, LCL) 20英尺货柜(Twenty Equivalent Unit, TEU)、40英尺货柜(Forty Equivalent Unit, FEU) 集装箱货运站(Container Freight Station, CFS) 基本港(Base Port)、非基本港(Non-Base Port) 电汇(T/T, Telegraphic Transfer) 托收(Collection);付款交单(D/P, Document of Payment);承兑交单(D/A, Document against Acceptance)二、各类单证中常用词汇 (一)商业发票(commercial invoice ) 出票人(drawer) 受票人(drawee) 运输说明(transport details) 发票号(invoice NO.) 发票日期(invoice date) 合同号(S/C NO.) 信用证号码和日期(L/C NO. and Date) 支付条款(Terms of Payment)
公司英语 -----教育训练部 一:常用术语 Hon Hai 鸿海 CMM Component module move 机动组件整合 CEM Contract Manufaction service 合约委托代工 IBSC Internet Business Solution Center 国际互联网应用中心 PCEG Personal Computer Enclosure group 个人计算机外设事业群(FOXTEQ)CCBG Connector&cable business group CPBG Competition business group ESBG Enterprise system business group 鸿富锦事业群 SABG system assembly business group 系统组装事业群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鸿准 Stamping tool shop I 冲模一厂 Stamping tool shop II 冲模二厂 Prototype workshop 样品中心 Steel factory 裁剪厂 PCE molding tooling workshop PCE塑模厂 Hua Nan test and measurement center 华南检测中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 镁合金 Engineer standard 工标 Document center (database center)资料中心 Design Center 设计中心 Painting 烤漆(厂) Assembly组装(厂) Stamping 冲压(厂) Education and Training教育训练 proposal improvement/creative suggestion提案改善 Technological exchange and study 技术交流研习会 Technology and Development Committee 技术发展委员会 BS Brain Storming 脑力激荡 QCC Quality Control Circle 品质圈
建筑常用英语词汇Chin ese restaura nt 中餐厅 civil air defense 人防 classicalorder 古典柱式 Client 甲 coat room衣帽间, cloak room行寄存处 coffee咖啡厅 color match 配色 color system色彩系统 com mon room, com mun ity room 公共活动室computer room电子计算机房 Concept & Master Planning 概念及总规划Conceptual Design 概念设计conference room 会议室
constructivism 构成主义Con tact 联系 Cornice 飞檐 corridor 走廊 cottage 农舍 courtyard house Den til齿饰 department 咅部门 Design Basis设计基础Design Code 设计规Design Deliverable 设计成果Design Institution Design Narrative 设计说明Design Principle 设计原贝U Design Proposal 设计案
Design Referenee 设计参考Design Schedule设计流程表Desig n Task设计任务Detail大样(建筑专用)dining room 餐室 Dormer天窗 dormitory 宿舍 Double-hung window 双悬窗Drawing图,图纸 Eave屋檐 Elevation 立面 elevator apartment 电梯式公寓entrance hall 门厅entertainment center 娱乐中心entrance 入口
六. Abbreviation
168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 R/D R/I RCCP REV RMA RMA ROP RPN RTV S/N S/O SAI SCM SFC SIP SIS SMD SMT SOP SOR SPC SPEC SQM SWOT TE TOC TPI TPM TQA TQC TQM VQA VQM W/H W/O WHS WIP Research and Development Run-In Rough Cut Capacity Planning Revision Returned Merchandise Access Return Merchandise Approval(or Authorization Re-Order Point Risk Priority Number Return To Vendor Serial Number Sales Order Social Accountability International Supply Chain Management Shop Floor Control Standard Inspection Procedule Strategic Information System Surface Mounting Device Surface Mounting Technology Standard Operation Procedure Special Order Request Statistical Process Control Specification Supplier Quality Management Strengths、Weaknesses、Opportunities、 Threates test engineering Theory of Constraints Total Productive Innovation Total Production Management Total Quality Assurance Total Quality Control Total Quality Management Vender Quality Approval Vendor Quality Management Warehouse Work Order warehouse Work In Process 研發部常溫熱機(老
外贸常用英语词汇 1.商品品质数量包装价格 品质条件 品质quality 规格specifications 等级grade 标准standard 样品sample 色彩样品colour sample 款式样品pattern sample 原样original sample 复样duplicate sample 对等样品countersample 参考样品reference sample 封样sealed sample 代表性样品representative sample 商品目录catalogue 宣传小册pamphlet 说明书description 公差tolerance 货号article No. 花色(搭配)assortment 增减5% plus or minus 大路货(良好平均品质)fair average quality 数量条件 个数pcs 长度length 面积area 体积volume 容积capacity 净重net weight 毛重gross weight 皮重tare 毛作净gross for net 溢短装条款more or less clause 重量weight 装运重量shipping weight 卸货重量landed weight 理论重量theoretical weight 公吨metric ton 长吨long ton 短吨short ton 公斤kilogram, kilo, kg 磅pound, lb 盎司ounce, oz 件piece 双pair 打dozen 令ream 套set l 立方米cubic meter 升litre 加仑gallon 蒲式耳bushel 公制metric system 英制british system 美制 包装方法 起泡包装blister packing 中性包装neutral packing 吸塑包装skin packing 挂式包装hanging packing 引某人注目catch sb's eye 唛头mark 无牌的包装unlabelled packing 散装in bulk 散装in loose packing 裸装nude packing 整批包装bulk pack 零售包装consumer pack 大包装large packing 小包装inner packing, external packing, end packing ,压缩包装shrunk packaging 喷泡沫包装foam-spary packaging 礼品包装gift-wrap 袋bag, sack 麻袋jute bag 塑料袋polythelene bag, plastic bag 尼龙绳网袋polythelene net 拉链袋zippered bag 箱case, chest 盒box 木箱wooden case 纸箱carton 集装箱container 板条箱rate 纤维板箱fibre board case 小包packet 包bale 捆bundle 罐头tin , can 篮,篓,筐basket 竹篓bamboo basket 瓶bottle 小木桶wooden keg 大桶hogshead 铁桶iron drum 铁桶cylinder
4A广告公司常用英语词汇 A above-the-line advertising 线上广告 广告代理商能从媒介获得佣金(代理费)的广告,如报刊广告、广播广告、电视广告、影院广告、户外广告等。 account executive (AE) :客户经理 广告公司的业务人员职称。客户经理往往须负责下列工作:1,与客户及内部其他部门共同计划广告(planning),向各部门传达客户的诉求;2,内部协调(coordination);3,将广告设计稿提供给客户;4,监督执行政府的有关广告规章和法规(regulatory matters);5,利润管理(agency profit management)。客户经理通过计划和协调公司的服务部门,为客户提供更好的服务。 account service 客户服务 客户服务是广告代理商的中心工作,肩负着使客户满意从而建立起长期的合作关系,及推动广告代理商内部工作有效运转的任务。它是广告代理商直接同客户进行沟通、交流的一种功能。 advertising agency 广告代理商 习惯上称为“广告公司”,即《中华人民共和国广告法》中所称的广告经营者,一般设有许多职能和业务部门。 advertising campaign 广告活动 有时称为“运动”或“战役”。广告活动包括以下四个重点:制作适当的销售信息、及时传达给受众、选择适当的时机,用合理的成本。广告主制定一项能测定的目标后,为达到这一目标制定广告战略,然后在市场上执行,包括:广告计划、广告制作、销售及营销等。 advertising department 广告部 分为企业的广告部和媒介的广告部。企业的广告经理负责拟定、审核及实施企业的广告计划。一般也是负责有关广告的具体工作。媒介的广告部经理负责出售报刊等的版面,广播、电视的时间等。 airport advertising 机场广告 利用机场的候机室及在机场内其他各种场地和设备上制作刊出的广告,也包括在指示牌上制作的广告。 Appeal 诉求 广告通过媒介向目标受众诉说,以求达到所期望的反应。诉求是制定某种道德、动机、认同,或是说服受众应该去做某件事的理由。诉求分三类:理性的、感性的和道义的。诉求所用语句应具有强烈的感染力。
Part IV:Commonly Used Professional Terms of Civil Engineering development organization 建设单位 design organization 设计单位 construction organization 施工单位 reinforced concrete 钢筋混凝土 pile 桩 steel structure 钢结构 aluminium alloy 铝合金 masonry 砌体(工程)reinforced ~ 配筋砌体load-bearing ~ 承重砌体unreinforced ~非配筋砌体 permissible stress (allowable stress) 容许应力plywood 胶合板 retaining wall 挡土墙 finish 装修 finishing material装修材料 ventilation 通风 natural ~ 自然通风 mechanical ~ 机械通风 diaphragm wall (continuous concrete wall) 地下连续墙 villa 别墅 moment of inertia 惯性矩 torque 扭矩 stress 应力normal ~ 法向应力shear ~ 剪应力 strain 应变 age hardening 时效硬化 air-conditioning system空调系统 (air) void ration(土)空隙比 albery壁厨,壁龛 a l mery壁厨,贮藏室 anchorage length锚固长度 antiseismic joint 防震缝 architectural appearance 建筑外观 architectural area 建筑面积 architectural design 建筑设计 fiashing 泛水 workability (placeability) 和易性 safety glass安全玻璃 tempered glass (reinforced glass) 钢化玻璃foamed glass泡沫玻璃 asphalt沥青 felt (malthoid) 油毡 riveted connection 铆接 welding焊接 screwed connection 螺栓连接 oakum 麻刀,麻丝 tee三通管 tap存水弯 esthetics美学 formwork 模板(工程) shoring 支撑 batching 配料 slipform construction (slipforming) 滑模施工 lfit-slab construction 升板法施工 mass concrete 大体积混凝土 terrazzo水磨石 construction joint 施工缝 honeycomb蜂窝,空洞,麻面 piled foundation桩基 deep foundation 深基础 shallow foundation浅基础 foundation depth基础埋深 pad foundation独立基础 strip foundation 条形基础 raft foundation筏基 box foundation箱形基础 BSMT=basement 地下室 lift 电梯electric elevator lift well电梯井 escalator 自动扶梯 Poisson’s ratio 泊松比μ Young’s modulus , modulus of elasticity 杨氏模量,弹性模量E safety coefficient 安全系数 fatigue failure 疲劳破坏 bearing capacity of foundations 地基承载力bearing capacity of a pile 单桩承载力 two-way-reinforcement 双向配筋 reinforced concrete two-way slabs钢筋混凝土双向板 single way slab单向板 window blind 窗帘sun blind wind load 风荷载 curing 养护 watertight concrete 防水混凝土 white cement白水泥 separating of concrete混凝土离折segregation of concrete mortar 砂浆~ joint 灰缝 pilaster 壁柱 fire rating耐火等级 fire brick 耐火砖 standard brick标准砖
电气工程常用专业英语词汇表 电气工程常用专业英语词汇表 电路基础 ideal voltage (current) source 理想电压(流)源volt-ampere characteristic 伏安特性potential difference 电位差 reference potential 参考电位resistance 电阻capacitance 电容 inductance 电感 reactance 电抗 inductive(capacitive) reactance 感(容)抗impedance 阻抗 equivalent circuit 等效电路 Ohm’s law 欧姆定律Kirchhoff’s law 基尔霍夫定律Kirchhoff’s voltage law(KVL)基尔霍夫电压定律Kirchhoff’s current law(KCL)基尔霍夫电流定律Thevenin’s theorem 戴维宁定理Norton’s theorem 诺顿定理 branch 支路 node 结点 loop 回路 mesh 网孔 open circuit 开路(断路) short circuit 短路 branch current analysis 支路电流法mesh current analysis 网孔电流法 ode voltage analysis 结点电位法n superposition theorem 叠加原理passive(active) two-terminal network 无(有)源二端网络root mean square (RMS) 均方根值 effective value 有效值instantaneous value 瞬时值 ampere 安培 volt 伏特 Hertz 赫兹 reactive power` 无功功率 active power 有功功率 transfer function 传递函数 apparent power 视在功率 power-factor compensation 功率因数补偿series (parallel) resonance 串(并)联谐振 amplitude(phase)-frequency response characteristic 幅(相)频特性 figure of merit 品质因素 pass-band 通频带bandwidth (BW) 带宽 first(second)-order filter 一(二)阶滤波器low(high)-pass filter 低(高)通滤波器band-pass(stop) filter 带通(阻)滤波器transfer function 转移函数 Bode diagram 波特图 Fourier series 傅立叶级数 three-phase circuit 三相电路 cutoff frequency 截止频率 FFT (Fast Fourier Transform) 快速傅立叶变换 state variable 状态变量 电机 generation 发电 transmission 输电 distribution 配电 coil 线圈 core 铁心 winding 绕组 electrical machine 电机 generator 发电机 motor 电动机 stator (rotor) 定子(转子) armature 电枢 brush 电刷 commutator 换向器 salient-pole 凸极 slip ring 滑环 induction motor 感应电动机 magnetic flux 磁通 asynchronous machine 异步电机 synchronous generator 同步发电机 eddy current 涡流 EMF(electromotive force)电动势 counter EMF 反电势 torque 转矩 excitation 励磁 prime mover 原动机 rectifier 整流器 leakage flux 漏磁通 demagnetization 退磁,去磁 short-circuit ratio 短路比 converter (inverter) 换流器(逆变器) synchronous condenser 同步调相机 magnetization curve 磁化曲线 separately exciting 他励 compounded excited 复励 self-exciting 自励 series(shunt)-wound 串(并)励
出口信贷export credit 出口津贴export subsidy 商品倾销dumping 外汇倾销exchange dumping 优惠关税special preferences 保税仓库bonded warehouse 贸易顺差favorable balance of trade 贸易逆差unfavorable balance of trade 进口配额制import quotas 自由贸易区free trade zone 对外贸易值value of foreign trade 国际贸易值value of international trade 普遍优惠制generalized system of preferences-GSP 最惠国待遇most-favored nation treatment-MFNT
价格条件 价格术语trade term (price term) 运费freight 单价price 码头费wharfage 总值total value 卸货费landing charges 金额amount 关税customs duty 净价net price 印花税stamp duty 含佣价price including commission 港口税port dues 回佣return commission . 装运港port of shipment
折扣discount, allowance 卸货港port of discharge 批发价wholesale price 目的港port of destination 零售价retail price 进口许口证import licence 现货价格spot price 出口许口证export licence 期货价格forward price 现行价格(时价)current price prevailing price 国际市场价格world (International)Market price 离岸价(船上交货价)FOB-free on board 成本加运费价(离岸加运费价)C&F-cost and freight 到岸价(成本加运费、保险费价)CIF-cost,insurance and freight 交货条件
一:常用術語 Hon Hai 鴻海 CMM Component module move 機動元件整合 CEM Contract Manu faction service 合約委托代工 IBSC Internet Business Solution Center 國際互聯網應用中心 PCEG Personal Computer Enclosure group 個人電腦外設事業群(FOXTEQ)CCBG Connector& cable business group CPBG Competition business group ESBG Enterprise system business group 鴻富錦事業群 SABG system assembly business group 系統組裝事業群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鴻準 Stamping tool shop I 沖模一廠 Stamping tool shop II 沖模二廠 Prototype workshop 樣品中心 Steel factory 裁剪廠 PCE molding tooling workshop PCE塑模廠 Hua Nan test and measurement center 華南檢測中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 鎂合金 Engineer standard 工標 Document center (database center)資料中心 Design Center 設計中心 Painting 烤漆(廠) Assembly組裝(廠) Stamping 沖壓(廠) Education and Training教育訓練 proposal improvement/creative suggestion提案改善 Technological exchange and study 技術交流研習會 Technology and Development Committee 技術發展委員會 BS Brain Storming 腦力激蕩 QCC Quality Control Circle 品質圈 PDCA Plan Do Check Action 計劃執行檢查總結 DCC delivery control center 交貨管制中心 3C Computer 電腦類產品 Consumer electronics 消費性電子產品 Communication 通訊類產品 Core value(核心价值) Love 愛心
英语建筑专业词汇 a. DESIGN BASIS 设计依据 b. DESIGN STAGE 设计阶段 c. CLIMATE CONDITION 气象条件 d. GENERAL ROOM NAME 常用房间名称 e. ROOFING & CEILING 屋面及天棚 f. WALL(CLADDING) 墙体(外墙板) g. FLOOR & TRENCH 地面及地沟 h. DOORS 、GLASS、WINDOWS & IRONMONGERY(HARDW ARE)门、玻璃、窗及五金件 I. STAIRCASE、LANDING & LIFT(ELEVATOR)楼梯、休息平台及电梯j. BUILDING MATERIAL WORDS AND PHRASES 建筑材料词汇及短语 【Bricks and Tiles 砖和瓦】 【Lime, Sand and Stone 灰、砂和石】【Cement, Mortar and Concrete 水泥、砂浆和混凝土】 【Facing And Plastering Materials 饰面及粉刷材料】 【Asphalt (Bitumen) and Asbestos 沥青和石棉】 【Timber 木材】 【Metallic Materials 金属材料】 【Non-Ferrous Metal 有色金属】 【Anti-Corrosion Materials 防腐蚀材料】【Building Hardware 建筑五金】 【Paint 油漆】 k. OTHER ARCHITECTURAL TERMS 其它建筑术语 【Discipline 专业】 【Conventional Terms 一般通用名词】【Architectural Physics 建筑物理】【Name Of Professional role 职务名称】【Drafting 制图】 a. DESIGN BASIS 设计依据 计划建议书planning proposals 设计任务书design order 标准规范standards and codes 条件图information drawing 设计基础资料basic data for design 工艺流程图process flowchart 工程地质资料engineering geological data 原始资料original data 设计进度schedule of design b. STAGE OF DESIGN 设计阶段 方案scheme, draft 草图sketch 会谈纪要summary of discussion 谈判negotiation 可行性研究feasibility study 初步设计preliminary design 基础设计basic design 详细设计detail design 询价图enquiry drawing 施工图working drawing, construction drawing 竣工图as built drawing c. CLIMATE CONDITION 气象条件 日照sunshine 风玫瑰wind rose 主导风向prevailing wind direction 最大(平均)风速maximum (mean) wind velocity 风荷载wind load 最大(平均)降雨量maximum (mean) rainfall 雷击及闪电thunder and lightning 飓风hurricane 台风typhoon 旋风cyclone 降雨强度rainfall intensity 年降雨量annual rainfall 湿球温度wet bulb temperature 干球温度dry bulb temperature 冰冻期frost period 冰冻线frost line 冰冻区frost zone 室外计算温度calculating outdoor temperature 采暖地区region with heating provision 不采暖地区region without heating provision 绝对大气压absolute atmospheric pressure 相对湿度relative humidity d. GENERAL ROOM NAME 常用房间名称办公室office
主题词表 English Chinese 01. 大气 atmospheric science 大气科学 meteorology 气象学 atmosphere 大气 atmospheric impurity 大气杂质 atmospheric suspended matter 大气悬浮物 atmospheric composition 大气成分 atmospheric mass 大气质量 atmospheric density 大气密度 atmospheric subdivision 大气分层 homosphere 均质层 heterosphere 非均质层 standard [pressure] level 标准层 isothermal layer 等温层 lower atmosphere 低层大气 middle atmosphere 中层大气 upper atmosphere 高层大气 troposphere 对流层 tropopause 对流层顶 stratosphere 平流层 stratopause 平流层顶 mesosphere 中间层 mesopause 中间层顶 thermosphere 热层 exosphere 外[逸]层 ionosphere 电离层 magnetosphere 磁层 ozonosphere 臭氧层 free atmosphere 自由大气 planetary atmosphere 行星大气 standard atmosphere(reference atmosphere) 标准大气(参考大气) homogeneous atmosphere 均质大气 isothermal atmosphere 等温大气 polytropic atmosphere 多元大气 scale height 大气标高 meteorological element 气象要素 air temperature 气温 wet-bulb temperature 湿球温度 dry-bulb temperature 干球温度 atmospheric pressure 气压 standard atmosphere pressure 标准大气压 station pressure 本站气压 sea-level pressure 海平面气压 pressure gradient 气压梯度 barometric height formula 压高公式pressure gradient force 气压梯度力Coriolis force 科里奥利力 water vapor 水[蒸]汽 water vapor pressure 水汽压 humidity 湿度 relative humidity 相对湿度 absolute humidity 绝对湿度 specific humidity 比湿 mixing ratio 混合比 dew point [temperature] 露点(温度) depression of the dew point (温度)露点差super-saturated air 过饱和空气 saturation specific humidity 饱和比湿saturation vapor pressure 饱和水汽压saturation deficit 饱和差 cloud 云 low cloud 低云 middle cloud 中云 high cloud 高云 cloud amount 云量 cloud height 云高 cloud genera 云属 cloud etage 云族 cloud species 云种 cloud variety 云类 cloud form 云状 cirrus, Ci 卷云 cirrostratus, Cs 卷层云 cirrocumulus, Cc 卷积云 altocumulus, Ac 高积云 altostratus, As 高层云 cumulus, Cu 积云 cumulus humilis, Cu hum 淡积云 cumulus congestus, Cu con 浓积云cumulonimbus, Cb 积雨云 cumulus fractus, Cu fra 碎积云stratocumulus, Sc 层积云 stratus, St 层云 nimbostratus, Ns 雨层云 stratiform cloud 层状云 cumuliform cloud 积状云 cold cloud 冷云 warm cloud 暖云 ice cloud 冰云 wind 风 wind direction 风向 wind speed, wind velocity 风速 maximum wind speed 最大风速